* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* assign icp_pit_init to icp_pit_info.instance_init
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SD spec for ACMD41 says that a zero argument is an "inquiry"
ACMD41, which does not start initialisation and is used only for
retrieving the OCR. However, Tianocore EDK2 (UEFI) has a bug [1]: it
first sends an inquiry (zero) ACMD41. If that first request returns an
OCR value with the power up bit (0x80000000) set, it assumes the card
is ready and continues, leaving the card in the wrong state. (My
assumption is that this works on hardware, because no real card is
immediately powered up upon reset.)
This change models a delay of 0.5ms from the first ACMD41 to the power
being up. However, it also immediately sets the power on upon seeing a
non-zero (non-enquiry) ACMD41. This speeds up UEFI boot, it should
also account for guests that simply delay after card reset and then
issue an ACMD41 that they expect will succeed.
[1] https://github.com/tianocore/edk2/blob/master/EmbeddedPkg/Universal/MmcDxe/MmcIdentification.c#L279
(This is the loop starting with "We need to wait for the MMC or SD
card is ready")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the creation of the SD card device from the sdhci_sysbus
device itself into the boards that create these devices.
This allows us to remove the cannot_instantiate_with_device_add
notation because we no longer call drive_get_next in the device
model.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-7-git-send-email-peter.maydell@linaro.org
Add a QOM bus for SD cards to plug in to.
Note that since sd_enable() is used only by one board and there
only as part of a broken implementation, we do not provide it in
the SDBus API (but instead add a warning comment about the old
function). Whoever converts OMAP and the nseries boards to QOM
will need to either implement the card switch properly or move
the enable hack into the OMAP MMC controller model.
In the SDBus API, the old-style use of sd_set_cb to register some
qemu_irqs for notification of card insertion and write-protect
toggling is replaced with methods in the SDBusClass which the
card calls on status changes and methods in the SDClass which
the controller can call to find out the current status. The
query methods will allow us to remove the abuse of the 'register
irqs' API by controllers in their reset methods to trigger
the card to tell them about the current status again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-5-git-send-email-peter.maydell@linaro.org
The following commits will remove support for the old sdhci-pci
command line syntax using the x-drive property:
-device sdhci-pci,x-drive=mydrive -drive id=mydrive,[...]
and replace it with an explicit sd device:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
(This is OK because x-drive is experimental.)
This commit removes the x-drive property so that old style
command lines will fail with a reasonable error message:
-device sdhci-pci,x-drive=mydrive: Property '.x-drive' not found
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-2-git-send-email-peter.maydell@linaro.org
Current QEMU doesn't clear PL061 state after reset. This causes a
weird issue with guest reboot via GPIO. Here is the device state
with two reboot requests:
(PL061State fields) data old_in_data istate
VM boot 0 0 0
After 1st ACPI reboot request 8 8 8
After VM PL061 driver ACK 8 8 0
After VM reboot 8 8 0
------------------------------------------------------------
2nd ACPI reboot request 8
In the second reboot request above, because the old_in_data field is 8,
QEMU decides that there is a pending edge IRQ already (see
pl061_update()) in input; so it doesn't raise up IRQ again. As a result
the second reboot request is lost. The correct way is to clear PL061
device state after reset.
The default reset state is found from the documents listed below. Per
Peter's suggestion that QEMU automatically calls reset function after
device initialization, this patch removes calling pl061_reset() from
pl061_initfn().
Reference:
[1] PL061 Technical Reference Manual
[2] Stellaris LM3S8962 Microcontroller Data Sheet
[3] Stellaris LM3S5P31 Microcontroller Data Sheet
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455729552-28026-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The LoPAPR specification defines the following for the RTAS
power-off call: "On successful operation, does not return".
However, the implementation in QEMU currently returns and runs
the guest CPU again for some more cycles. This caused some
trouble with the new ppc implementation of the kvm-unit-tests
recently. So let's make sure that the QEMU implementation
follows the spec, thus stop the CPU to make sure that the
RTAS call does not return to the guest anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4b23699 "pseries: Add pseries-2.6 machine type" added a new
SPAPR_COMPAT_2_5 macro in the usual way. However, it didn't add this
macro to the existing SPAPR_COMPAT_2_4 macro so that pseries-2.4
inherits newer compatibility properties which are needed for 2.5 and
earlier.
This corrects the oversight.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Also implement the command, by removing the hardcoded period of 20 ms/50 Hz
and replacing it by the one requested by user.
Update VMState version to store this new parameter.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SET_XDABR hypercall is similar to H_SET_DABR, but also sets
the extended DABR (DABRX) register.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to LoPAPR, h_set_dabr should simply set DABRX to 3
(if the register is available), and load the parameter into DABR.
If DABRX is not available, the hypervisor has to check the
"Breakpoint Translation" bit of the DABR register first.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a very simple hypercall that only sets up the SPRG0
register for the guest (since writing to SPRG0 was only permitted
to the hypervisor in older versions of the PowerISA).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
htab_save_first_pass could return without finishing its work due to
timeout. The patch checks if another invocation of it is necessary and
will call it in htab_save_complete if necessary.
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[removed overlong line]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With HV KVM, the guest's hash page table (HPT) is managed by the kernel and
not directly accessible to QEMU. This means that spapr->htab is NULL
and normally env->external_htab would also be NULL for each cpu.
However, that would cause ppc_hash64_load_hpte*() to do the wrong thing in
the few cases where QEMU does need to load entries from the in-kernel HPT.
Specifically, seeing external_htab is NULL, they would look for an HPT
within the guest's address space instead.
To stop that we have an ugly hack in the pseries machine type code to
set external htab to (void *)1 instead.
This patch removes that hack by having ppc_hash64_load_hpte*() explicitly
check kvmppc_kern_htab instead, which makes more sense.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At the moment the size of the hash page table (HPT) is fixed based on the
maximum memory allowed to the guest. As such, we allocate the table during
machine construction, and just clear it at reset.
However, we're planning to implement a PAPR extension allowing the hash
page table to be resized at runtime. This will mean that on reset we want
to revert it to the default size. It also means that when migrating, we
need to make sure the destination allocates an HPT of size matching the
host, since the guest could have changed it before the migration.
This patch replaces the spapr_alloc_htab() and spapr_reset_htab() functions
with a new spapr_reallocate_hpt() function. This is called at reset and
inbound migration only, not during machine init any more.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At present we calculate the recommended hash page table (HPT) size for a
pseries guest just once in ppc_spapr_init() before allocating the HPT.
In future patches we're going to want this calculation in other places, so
this splits it out into a helper function. While we're at it, change the
calculation to use ctz() instead of an explicit loop.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When migrating the 'pseries' machine type with KVM, we use a special fd
to access the hash page table stored within KVM. Usually, this fd is
opened at the beginning of migration, and kept open until the migration
is complete.
However, if there is a guest reset during the migration, the fd can become
stale and we need to re-open it. At the moment we use an 'htab_fd_stale'
flag in sPAPRMachineState to signal this, which is checked in the migration
iterators.
But that's rather ugly. It's simpler to just close and invalidate the
fd on reset, and lazily re-open it in migration if necessary. This patch
implements that change.
This requires a small addition to the machine state's instance_init,
so that htab_fd is initialized to -1 (telling the migration code it
needs to open it) instead of 0, which could be a valid fd.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
* Coverity fixes for IPMI and mptsas
* qemu-char fixes from Daniel and Marc-André
* Bug fixes that break qemu-iotests
* Changes to fix reset from panicked state
* checkpatch false positives for designated initializers
* TLS support in the NBD servers and clients
# gpg: Signature made Tue 16 Feb 2016 16:27:17 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
nbd: enable use of TLS with nbd-server-start command
nbd: enable use of TLS with qemu-nbd server
nbd: enable use of TLS with NBD block driver
nbd: implement TLS support in the protocol negotiation
nbd: use "" as a default export name if none provided
nbd: always query export list in fixed new style protocol
nbd: allow setting of an export name for qemu-nbd server
nbd: make client request fixed new style if advertised
nbd: make server compliant with fixed newstyle spec
nbd: invert client logic for negotiating protocol version
nbd: convert to using I/O channels for actual socket I/O
nbd: convert blockdev NBD server to use I/O channels for connection setup
nbd: convert qemu-nbd server to use I/O channels for connection setup
nbd: convert block client to use I/O channels for connection setup
qemu-nbd: add support for --object command line arg
qom: add helpers for UserCreatable object types
ipmi: sensor number should not exceed MAX_SENSORS
mptsas: fix wrong formula
mptsas: fix memory leak
mptsas: add missing va_end
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a number of off-by-ones, one of them spotted by Coverity.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MPI_DOORBELL_WHO_INIT_SHIFT is being repeated twice. Reported
by Coverity.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
