Section 3.4.7 of the datasheet explains that,
The RBE bit in the Interrupt Status register is set when the
SONIC finishes using the second to last receive buffer and reads
the last RRA descriptor. Actually, the SONIC is not truly out of
resources, but gives the system an early warning of an impending
out of resources condition.
RBE does not mean actual receive buffer exhaustion, and reception should
not be stopped. This is important because Linux will not check and clear
the RBE interrupt until it receives another packet. But that won't
happen if can_receive returns false. This bug causes the SONIC to become
deaf (until reset).
Fix this with a new flag to indicate actual receive buffer exhaustion.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit c2279bd0a1)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The jazzsonic driver in Linux uses the Silicon Revision register value
to probe the chip. The driver fails unless the SR register contains 4.
Unfortunately, reading this register in QEMU usually returns 0 because
the s->regs[] array gets wiped after a software reset.
Fixes: bd8f1ebce4 ("net/dp8393x: fix hardware reset")
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 083e21bbdd)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
These operations need to take place regardless of whether or not
rx descriptors have been used up (that is, EOL flag was observed).
The algorithm is now the same for a packet that was withheld as for
a packet that was not.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 80b60673ea)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When the SONIC receives a packet into the last available descriptor, it
retains ownership of that descriptor for as long as necessary.
Section 3.4.7 of the datasheet says,
When the system appends more descriptors, the SONIC releases ownership
of the descriptor after writing 0000h to the RXpkt.in_use field.
The packet can now be processed by the host, so raise a PKTRX interrupt,
just like the normal case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit d9fae13196)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The existing code has a bug where the Remaining Buffer Word Count (RBWC)
is calculated with a truncating division, which gives the wrong result
for odd-sized packets.
Section 1.4.1 of the datasheet says,
Once the end of the packet has been reached, the serializer will
fill out the last word (16-bit mode) or long word (32-bit mode)
if the last byte did not end on a word or long word boundary
respectively. The fill byte will be 0FFh.
Implement buffer padding so that buffer limits are correctly enforced.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 350e7d9a77)
*drop context dependencies from b7cbebf2b9, 1ccda935d4, and
19f7034773
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Section 3.4.1 of the datasheet says,
The alignment of the RRA is confined to either word or long word
boundaries, depending upon the data width mode. In 16-bit mode,
the RRA must be aligned to a word boundary (A0 is always zero)
and in 32-bit mode, the RRA is aligned to a long word boundary
(A0 and A1 are always zero).
This constraint has been implemented for 16-bit mode; implement it
for 32-bit mode too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit ea2270279b)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
A received packet consumes pkt_size bytes in the buffer and the frame
checksum that's appended to it consumes another 4 bytes. The Receive
Buffer Address register takes the former quantity into account but
not the latter. So the next packet written to the buffer overwrites
the frame checksum. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit bae112b80c)
*drop context dep. on 19f7034773
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Add a bounds check to prevent a large packet from causing a buffer
overflow. This is defensive programming -- I haven't actually tried
sending an oversized packet or a jumbo ethernet frame.
The SONIC handles packets that are too big for the buffer by raising
the RBAE interrupt and dropping them. Linux uses that interrupt to
count dropped packets.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit ada7431527)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Follow the algorithm given in the National Semiconductor DP83932C
datasheet in section 3.4.7:
At the next reception, the SONIC re-reads the last RXpkt.link field,
and updates its CRDA register to point to the next descriptor.
The chip is designed to allow the host to provide a new list of
descriptors in this way.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 5b0c98fcb7)
*drop context dep on 19f7034773
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This function re-uses its 'size' argument as a scratch variable.
Instead, declare a local 'size' variable for that purpose so that the
function result doesn't get messed up.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 9e3cd456d8)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
According to the datasheet, section 3.4.4, "in 32-bit mode ... the SONIC
always writes long words".
Therefore, use the same technique for the 'in_use' field that is used
everywhere else, and write the full long word.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 46ffee9ad4)
Conflicts:
hw/net/dp8393x.c
*roll in local dependencies on b7cbebf2b9
*drop functional dep. on 19f7034773
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The DP83932 and DP83934 have 32 data lines. The datasheet says,
Data Bus: These bidirectional lines are used to transfer data on the
system bus. When the SONIC is a bus master, 16-bit data is transferred
on D15-D0 and 32-bit data is transferred on D31-D0. When the SONIC is
accessed as a slave, register data is driven onto lines D15-D0.
D31-D16 are held TRI-STATE if SONIC is in 16-bit mode. If SONIC is in
32-bit mode, they are driven, but invalid.
Always use 32-bit accesses both as bus master and bus slave.
Force the MSW to zero in bus master mode.
This gets the Linux 'jazzsonic' driver working, and avoids the need for
prior hacks to make the NetBSD 'sn' driver work.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 3fe9a838ec)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The Least Significant bit of a descriptor address register is used as
an EOL flag. It has to be masked when the register value is to be used
as an actual address for copying memory around. But when the registers
are to be updated the EOL bit should not be masked.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 88f632fbb1)
Conflicts:
hw/net/dp8393x.c
*drop context dep. on 19f7034773
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Functions that take an Error ** parameter to pass an error to the
caller expect the parameter to point to null.
failover_replug_primary() violates this precondition in several
places:
* After qemu_opts_from_qdict() failed, *errp is no longer null.
Passing it to error_setg() is wrong, and will trip the assertion in
error_setv(). Messed up in commit 150ab54aa6 "net/virtio: fix
re-plugging of primary device". Simply drop the error_setg().
* Passing @errp to qemu_opt_set_bool(), hotplug_handler_pre_plug(),
and hotplug_handler_plug() is wrong. If one of the first two fails,
*errp is no longer null. Risks tripping the same assertion.
Moreover, continuing after such errors is unsafe. Messed up in
commit 9711cd0dfc "net/virtio: add failover support". Fix by
handling each error properly.
failover_replug_primary() crashes when passed a null @errp. Also
messed up in commit 9711cd0dfc. This bug can't bite as no caller
actually passes null. Fix it anyway.
Fixes: 9711cd0dfc
Fixes: 150ab54aa6
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-3-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
virtio_net_handle_migration_primary() returns early when it can't
ensure n->primary_dev is non-null. Checking it again right after that
early return is redundant. Drop.
If n->primary_dev is null on entering failover_replug_primary(), @pdev
will become null, and pdev->partially_hotplugged will crash. Checking
n->primary_dev later is useless. It can't actually be null, because
its caller virtio_net_handle_migration_primary() ensures it isn't.
Drop the useless check.
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-2-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
failover_replug_primary was returning true on failure which lead to
re-plug not working when a migration failed. Fix this by returning
success when hotplug worked. This is a bug that was missed in last
round of testing but was tested succesfully with this version. Also
make sure we don't pass NULL to qdev_set_parent_bus().
This fixes CID 1407224.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Bail out when primary device was already added before.
This avoids printing a wrong warning message during reboot.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
.dev_unplug_pending is set up by virtio-net code indepent of failover
support was set for the device or not. This gives a wrong result when
we check for existing primary devices in migration code.
Fix this by actually calling dev_unplug_pending() instead of just
checking if the function pointer was set. When the feature was not
negotiated dev_unplug_pending() will always return false. This prevents
us from going into the wait-unplug state when there's no primary device
present.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
RXpkt.in_use is always 16 bit wide, but when the bus access mode is 32bit
and the endianness is big, we must access the second word and not the
first. This patch adjusts the offset according to the size and endianness.
This fixes DHCP for Q800 guest.
Fixes: be92084198 ("dp8393x: manage big endian bus")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191106112341.23735-3-laurent@vivier.eu>
This patch adds support to handle failover device pairs of a virtio-net
device and a (vfio-)pci device, where the virtio-net acts as the standby
device and the (vfio-)pci device as the primary.
The general idea is that we have a pair of devices, a (vfio-)pci and a
emulated (virtio-net) device. Before migration the vfio device is
unplugged and data flows to the emulated device, on the target side
another (vfio-)pci device is plugged in to take over the data-path. In the
guest the net_failover module will pair net devices with the same MAC
address.
To achieve this we need:
1. Provide a callback function for the should_be_hidden DeviceListener.
It is called when the primary device is plugged in. Evaluate the QOpt
passed in to check if it is the matching primary device. It returns
if the device should be hidden or not.
When it should be hidden it stores the device options in the VirtioNet
struct and the device is added once the VIRTIO_NET_F_STANDBY feature is
negotiated during virtio feature negotiation.
If the virtio-net devices are not realized at the time the (vfio-)pci
devices are realized, we need to connect the devices later. This way
we make sure primary and standby devices can be specified in any
order.
2. Register a callback for migration status notifier. When called it
will unplug its primary device before the migration happens.
3. Register a callback for the migration code that checks if a device
needs to be unplugged from the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-11-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 29 Oct 2019 02:33:36 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
COLO-compare: Fix incorrect `if` logic
virtio-net: prevent offloads reset on migration
virtio: new post_load hook
net: add tulip (dec21143) driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add Macintosh Quadra 800 machine in hw/m68k
# gpg: Signature made Mon 28 Oct 2019 18:14:25 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier/tags/q800-branch-pull-request:
BootLinuxConsoleTest: Test the Quadra 800
hw/m68k: define Macintosh Quadra 800
hw/m68k: add a dummy SWIM floppy controller
hw/m68k: add Nubus macfb video card
hw/m68k: add Nubus support
hw/m68k: implement ADB bus support for via
hw/m68k: add VIA support
dp8393x: manage big endian bus
esp: add pseudo-DMA as used by Macintosh
esp: move get_cmd() post-DMA code to get_cmd_cb()
esp: move handle_ti_cmd() cleanup code to esp_do_dma().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently offloads disabled by guest via the VIRTIO_NET_CTRL_GUEST_OFFLOADS_SET
command are not preserved on VM migration.
Instead all offloads reported by guest features (via VIRTIO_PCI_GUEST_FEATURES)
get enabled.
What happens is: first the VirtIONet::curr_guest_offloads gets restored and offloads
are getting set correctly:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=0, tso6=0, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_post_load_device (opaque=0x555557701ca0, version_id=11) at hw/net/virtio-net.c:2334
#3 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577c80 <vmstate_virtio_net_device>, opaque=0x555557701ca0, version_id=11)
at migration/vmstate.c:168
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2197
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
However later on the features are getting restored, and offloads get reset to
everything supported by features:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=1, tso6=1, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_set_features (vdev=0x555557701ca0, features=5104441767) at hw/net/virtio-net.c:773
#3 virtio_set_features_nocheck (vdev=0x555557701ca0, val=5104441767) at hw/virtio/virtio.c:2052
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2220
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
Fix this by preserving the state in saved_guest_offloads field and
pushing out offload initialization to the new post load hook.
Cc: qemu-stable@nongnu.org
Signed-off-by: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the basic functionality to emulate a Tulip NIC.
Implemented are:
- RX and TX functionality
- Perfect Frame Filtering
- Big/Little Endian descriptor support
- 93C46 EEPROM support
- LXT970 PHY
Not implemented, mostly because i had no OS using these functions:
- Imperfect frame filtering
- General Purpose Timer
- Transmit automatic polling
- Boot ROM support
- SIA interface
- Big/Little Endian data buffer conversion
Successfully tested with the following Operating Systems:
- MSDOS with Microsoft Network Client 3.0 and DEC ODI drivers
- HPPA Linux
- Windows XP
- HP-UX
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191022155413.4619-1-svens@stackframe.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Block patches for softfreeze:
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
# gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits)
qemu-iotests: restrict 264 to qcow2 only
Revert "qemu-img: Check post-truncation size"
block: Pass truncate exact=true where reasonable
block: Let format drivers pass @exact
block: Evaluate @exact in protocol drivers
block: Add @exact parameter to bdrv_co_truncate()
block: Do not truncate file node when formatting
block/cor: Drop cor_co_truncate()
block: Handle filter truncation like native impl.
iotests: Test qcow2's snapshot table handling
iotests: Add peek_file* functions
qcow2: Fix v3 snapshot table entry compliancy
qcow2: Repair snapshot table with too many entries
qcow2: Fix overly long snapshot tables
qcow2: Keep track of the snapshot table length
qcow2: Fix broken snapshot table entries
qcow2: Add qcow2_check_fix_snapshot_table()
qcow2: Separate qcow2_check_read_snapshot_table()
qcow2: Write v3-compliant snapshot list on upgrade
qcow2: Put qcow2_upgrade() into its own function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio: features, tests
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 25 Oct 2019 12:47:59 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (25 commits)
virtio: drop unused virtio_device_stop_ioeventfd() function
libqos: add VIRTIO PCI 1.0 support
libqos: extract Legacy virtio-pci.c code
libqos: make the virtio-pci BAR index configurable
libqos: expose common virtqueue setup/cleanup functions
libqos: add MSI-X callbacks to QVirtioPCIDevice
libqos: pass full QVirtQueue to set_queue_address()
libqos: add iteration support to qpci_find_capability()
libqos: access VIRTIO 1.0 vring in little-endian
libqos: implement VIRTIO 1.0 FEATURES_OK step
libqos: enforce Device Initialization order
libqos: add missing virtio-9p feature negotiation
tests/virtio-blk-test: set up virtqueue after feature negotiation
virtio-scsi-test: add missing feature negotiation
libqos: extend feature bits to 64-bit
libqos: read QVIRTIO_MMIO_VERSION register
tests/virtio-blk-test: read config space after feature negotiation
virtio: add property to enable packed virtqueue
vhost_net: enable packed ring support
virtio: event suppression support for packed ring
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the cmsdk-apb-watchdog code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-22-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
Every caller of spapr_vio_qirq() immediately calls qemu_irq_pulse() with
the result, so we might as well just fold that into the helper.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
target-arm queue:
* target/arm: generate a custom MIDR for -cpu max
* hw/misc/zynq_slcr: refactor to use standard register definition
* Set ENET_BD_BDU in I.MX FEC controller
* target/arm: Fix routing of singlestep exceptions
* refactor a32/t32 decoder handling of PC
* minor optimisations/cleanups of some a32/t32 codegen
* target/arm/cpu64: Ensure kvm really supports aarch64=off
* target/arm/cpu: Ensure we can use the pmu with kvm
* target/arm: Minor cleanups preparatory to KVM SVE support
# gpg: Signature made Fri 16 Aug 2019 14:15:55 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190816: (29 commits)
target/arm: Use tcg_gen_extrh_i64_i32 to extract the high word
target/arm: Simplify SMMLA, SMMLAR, SMMLS, SMMLSR
target/arm: Use tcg_gen_rotri_i32 for gen_swap_half
target/arm: Use ror32 instead of open-coding the operation
target/arm: Remove redundant shift tests
target/arm: Use tcg_gen_deposit_i32 for PKHBT, PKHTB
target/arm: Use tcg_gen_extract_i32 for shifter_out_im
target/arm/kvm64: Move the get/put of fpsimd registers out
target/arm/kvm64: Fix error returns
target/arm/cpu: Use div-round-up to determine predicate register array size
target/arm/helper: zcr: Add build bug next to value range assumption
target/arm/cpu: Ensure we can use the pmu with kvm
target/arm/cpu64: Ensure kvm really supports aarch64=off
target/arm: Remove helper_double_saturate
target/arm: Use unallocated_encoding for aarch32
target/arm: Remove offset argument to gen_exception_bkpt_insn
target/arm: Replace offset with pc in gen_exception_internal_insn
target/arm: Replace offset with pc in gen_exception_insn
target/arm: Replace s->pc with s->base.pc_next
target/arm: Remove redundant s->pc & ~1
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
