Generalize nvic_sysreg_ns_ops so that we can pass it an
arbitrary MemoryRegion which it will use as the underlying
register implementation to apply the NS-alias behaviour
to. We'll want this so we can do the same with systick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-2-git-send-email-peter.maydell@linaro.org
Now that do_ats_write() is entirely in control of whether to
generate a 32-bit PAR or a 64-bit PAR, we can make it use the
correct (complicated) condition for doing so.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1512503192-2239-13-git-send-email-peter.maydell@linaro.org
[PMM: Rebased Edgar's patch on top of get_phys_addr() refactoring;
use arm_s1_regime_using_lpae_format() rather than
regime_using_lpae_format() because the latter will assert
if passed ARMMMUIdx_S12NSE0 or ARMMMUIdx_S12NSE1;
updated commit message appropriately]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In do_ats_write(), rather than using the FSR value from get_phys_addr(),
construct the PAR values using the information in the ARMMMUFaultInfo
struct. This allows us to create a PAR of the correct format regardless
of what the translation table format is.
For the moment we leave the condition for "when should this be a
64 bit PAR" as it was previously; this will need to be fixed to
properly support AArch32 Hyp mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-11-git-send-email-peter.maydell@linaro.org
Now that ARMMMUFaultInfo is guaranteed to have enough information
to construct a fault status code, we can pass it in to the
deliver_fault() function and let it generate the correct type
of FSR for the destination, rather than relying on the value
provided by get_phys_addr().
I don't think there are any cases the old code was getting
wrong, but this is more obviously correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-10-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_pmsav5() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Note that PMSAv5 does not define any guest-visible fault status
register, so the different "fsr" values we were previously
returning are entirely arbitrary. So we can just switch to using
the most appropriae fi->type values without worrying that we
need to special-case FaultInfo->FSC conversion for PMSAv5.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-7-git-send-email-peter.maydell@linaro.org
All the callers of arm_ldq_ptw() and arm_ldl_ptw() ignore the value
that those functions store in the fsr argument on failure: if they
return failure to their callers they will always overwrite the fsr
value with something else.
Remove the argument from these functions and S1_ptw_translate().
This will simplify removing fsr from the calling functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-3-git-send-email-peter.maydell@linaro.org
Currently get_phys_addr() and its various subfunctions return
a hard-coded fault status register value for translation
failures. This is awkward because FSR values these days may
be either long-descriptor format or short-descriptor format.
Worse, the right FSR type to use doesn't depend only on the
translation table being walked -- some cases, like fault
info reported to AArch32 EL2 for some kinds of ATS operation,
must be in long-descriptor format even if the translation
table being walked was short format. We can't get those cases
right with our current approach.
Provide fields in the ARMMMUFaultInfo struct which allow
get_phys_addr() to provide sufficient information for a caller to
construct an FSR value themselves, and utility functions which do
this for both long and short format FSR values, as a first step in
switching get_phys_addr() and its children to only returning the
failure cause in the ARMMMUFaultInfo struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-2-git-send-email-peter.maydell@linaro.org
For the TT instruction we're going to need to do an MPU lookup that
also tells us which MPU region the access hit. This requires us
to do the MPU lookup without first doing the SAU security access
check, so pull the MPU lookup parts of get_phys_addr_pmsav8()
out into their own function.
The TT instruction also needs to know the MPU region number which
the lookup hit, so provide this information to the caller of the
MPU lookup code, even though get_phys_addr_pmsav8() doesn't
need to know it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-7-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The TT instruction is going to need to look up the MMU index
for a specified security and privilege state. Refactor the
existing arm_v7m_mmu_idx_for_secstate() into a version that
lets you specify the privilege state and one that uses the
current state of the CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-6-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For M profile, we currently have an mmu index MNegPri for
"requested execution priority negative". This fails to
distinguish "requested execution priority negative, privileged"
from "requested execution priority negative, usermode", but
the two can return different results for MPU lookups. Fix this
by splitting MNegPri into MNegPriPriv and MNegPriUser, and
similarly for the Secure equivalent MSNegPri.
This takes us from 6 M profile MMU modes to 8, which means
we need to bump NB_MMU_MODES; this is OK since the point
where we are forced to reduce TLB sizes is 9 MMU modes.
(It would in theory be possible to stick with 6 MMU indexes:
{mpu-disabled,user,privileged} x {secure,nonsecure} since
in the MPU-disabled case the result of an MPU lookup is
always the same for both user and privileged code. However
we would then need to rework the TB flags handling to put
user/priv into the TB flags separately from the mmuidx.
Adding an extra couple of mmu indexes is simpler.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-5-git-send-email-peter.maydell@linaro.org
In ARMv7M the CPU ignores explicit writes to CONTROL.SPSEL
in Handler mode. In v8M the behaviour is slightly different:
writes to the bit are permitted but will have no effect.
We've already done the hard work to handle the value in
CONTROL.SPSEL being out of sync with what stack pointer is
actually in use, so all we need to do to fix this last loose
end is to update the condition we use to guard whether we
call write_v7m_control_spsel() on the register write.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-3-git-send-email-peter.maydell@linaro.org
For v8M it is possible for the CONTROL.SPSEL bit value and the
current stack to be out of sync. This means we need to update
the checks used in reads and writes of the PSP and MSP special
registers to use v7m_using_psp() rather than directly checking
the SPSEL bit in the control register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When support for multiple mappings per a region were added, this was
left behind, let's finish and remove unused bits.
Fixes: db0da029a1 ("vfio: Generalize region support")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The vfio_iommu_spapr_tce driver advertises kernel's support for
v1 and v2 IOMMU support, however it is not always possible to use
the requested IOMMU type. For example, a pseries host platform does not
support dynamic DMA windows so v2 cannot initialize and QEMU fails to
start.
This adds a fallback to the v1 IOMMU if v2 cannot be used.
Fixes: 318f67ce13 ("vfio: spapr: Add DMA memory preregistering (SPAPR IOMMU v2)")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 8c37faa475 ("vfio-pci, ppc64/spapr: Reorder group-to-container
attaching") moved registration of groups with the vfio-kvm device from
vfio_get_group() to vfio_connect_container(), but it missed the case
where a group is attached to an existing container and takes an early
exit. Perhaps this is a less common case on ppc64/spapr, but on x86
(without viommu) all groups are connected to the same container and
thus only the first group gets registered with the vfio-kvm device.
This becomes a problem if we then hot-unplug the devices associated
with that first group and we end up with KVM being misinformed about
any vfio connections that might remain. Fix by including the call to
vfio_kvm_device_add_group() in this early exit path.
Fixes: 8c37faa475 ("vfio-pci, ppc64/spapr: Reorder group-to-container attaching")
Cc: qemu-stable@nongnu.org # qemu-2.10+
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The refactoring of commit 296e5a0a6c has a nasty bug:
it accidentally dropped the generation of code to raise
the UNDEF exception when disas_thumb2_insn() returns nonzero.
This means that 32-bit Thumb2 instruction patterns that
ought to UNDEF just act like nops instead. This is likely
to break any number of things, including the kernel's "disable
the FPU and use the UNDEF exception to identify when to turn
it back on again" trick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513006964-3371-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
pci_find_primary_bus() only has one user, in pc_xen_hvm_init(). That's
inside the machine construction code, so it already has easy access to the
machine's primary PCI bus.
Get it directly, and thereby remove pci_find_primary_bus(). This removes
one of only a handful of users of the ugly pci_host_bridges global.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
include/hw/pci/pci_bus.h contains several data structures related to PCI
bridges that aren't needed by most users of pci_bus.h. We already have
a pci_bridge.h, so move them there.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
pci_bus_init(), pci_bus_new_inplace(), pci_bus_new() and pci_register_bus()
are misleadingly named. They're not used for initializing *any* PCI bus,
but only for a root PCI bus.
Non-root buses - i.e. ones under a logical PCI to PCI bridge - are instead
created with a direct qbus_create_inplace() (see pci_bridge_initfn()).
This patch renames the functions to make it clear they're only used for
a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
