In e820_add_entry() the e820_table is reallocated with g_renew() to make
space for a new entry. However, fw_cfg_arch_create() just uses the
existing e820_table pointer. This leads to a use-after-free if anything
adds a new entry after fw_cfg is set up.
Shift the addition of the etc/e820 file to the machine done notifier, via
a new fw_cfg_add_e820() function.
Also make e820_table private and use an e820_get_table() accessor function
for it, which sets a flag that will trigger an assert() for any *later*
attempts to add to the table.
Make e820_add_entry() return void, as most callers don't check for error
anyway.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <a2708734f004b224f33d3b4824e9a5a262431568.camel@infradead.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
fw_cfg.c and vapic.c are currently included unconditionally but
depend on other components. vapic.c depends on the local APIC,
while fw_cfg.c includes a piece of AML builder code that depends
on CONFIG_ACPI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240509170044.190795-9-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Current code uses mix of error_report()+exit(1)
and error_setg() to handle errors.
Use newer error_setg() everywhere, beside consistency
it will allow to detect error condition without killing
QEMU and attempt switch-over to SMBIOS3.x tables/entrypoint
in follow up patch.
while at it, clear smbios_tables pointer after freeing.
that will avoid double free if smbios_get_tables() is called
multiple times.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-13-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
legacy mode doesn't support structures of type 2 and more,
and CLI has a check for '-smbios type' option, however it's
still possible to sneak in type4 as a blob with '-smbios file'
option. However doing the later makes SMBIOS tables broken
since SeaBIOS doesn't expect that.
Rather than trying to add support for type4 to legacy code
(both QEMU and SeaBIOS), simplify smbios_get_table_legacy()
by dropping not relevant check in legacy code and error out
on type4 blob.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
smbios_get_tables() bails out right away if leagacy mode is enabled
and won't generate any SMBIOS tables. At the same time x86 specific
fw_cfg_build_smbios() will genarate legacy tables and then proceed
to preparing temporary mem_array for useless call to
smbios_get_tables() and then discard it.
Drop legacy related check in smbios_get_tables() and return from
fw_cfg_build_smbios() early if legacy tables where built without
proceeding to non legacy part of the function.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Handling most of smbios data generation in the machine_done notifier is similar
to how the ARM virt machine handles it which also calls smbios_set_defaults()
there. The result is that all pc machines are freed from explicitly worrying
about smbios setup.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240208220349.4948-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
e820 reserved entries were used before the dynamic entries with fw config files
were intoduced. Please see the following change:
7d67110f2d9a6("pc: add etc/e820 fw_cfg file")
Identical support was introduced into seabios as well with the following commit:
ce39bd4031820 ("Add support for etc/e820 fw_cfg file")
Both the above commits are now quite old. QEMU machines 1.7 and newer no longer
use the reserved entries. Seabios uses fw config files and
dynamic e820 entries by default and only falls back to using reserved entries
when it has to work with old qemu (versions earlier than 1.7). Please see
functions qemu_cfg_e820() and qemu_early_e820(). It is safe to remove legacy
FW_CFG_E820_TABLE and associated code now as QEMU 7.0 has deprecated i440fx
machines 1.7 and older. It would be incredibly rare to run the latest qemu
version with a very old version of seabios that did not support fw config files
for e820.
As far as I could see, edk2/ovfm never supported reserved entries and uses fw
config files from the beginning. So there should be no incompatibilities with
ovfm as well.
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220831045311.33083-1-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Type 41 defines the attributes of devices that are onboard. The
original intent was to imply the BIOS had some level of control over
the enablement of the associated devices.
If network devices are present in this table, by default, udev will
name the corresponding interfaces enoX, X being the instance number.
Without such information, udev will fallback to using the PCI ID and
this usually gives ens3 or ens4. This can be a bit annoying as the
name of the network card may depend on the order of options and may
change if a new PCI device is added earlier on the commande line.
Being able to provide SMBIOS type 41 entry ensure the name of the
interface won't change and helps the user guess the right name without
booting a first time.
This can be invoked with:
$QEMU -netdev user,id=internet
-device virtio-net-pci,mac=50:54:00:00:00:42,netdev=internet,id=internet-dev \
-smbios type=41,designation='Onboard LAN',instance=1,kind=ethernet,pcidev=internet-dev
The PCI segment is assumed to be 0. This should hold true for most
cases.
$ dmidecode -t 41
# dmidecode 3.3
Getting SMBIOS data from sysfs.
SMBIOS 2.8 present.
Handle 0x2900, DMI type 41, 11 bytes
Onboard Device
Reference Designation: Onboard LAN
Type: Ethernet
Status: Enabled
Type Instance: 1
Bus Address: 0000:00:09.0
$ ip -brief a
lo UNKNOWN 127.0.0.1/8 ::1/128
eno1 UP 10.0.2.14/24 fec0::5254:ff:fe00:42/64 fe80::5254:ff:fe00:42/64
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Message-Id: <20210401171138.62970-1-vincent@bernat.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These are needed by microvm too, so move them outside of PC-specific files.
With this patch, microvm.c need not include pc.h anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The microvm machine type uses fw_cfg but lacks SMBIOS and ACPI. Do not
include the files if the symbol is not present in QEMU and remove
dependencies on machine-specific files.
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
