Add a check that the requested offset + length does not go beyond the end
of the cel_log.
Whilst the cci->cel_log is large enough to include all possible CEL
entries, the guest might still ask for entries beyond the end of it.
Move the comment to this new check rather than before the check on the
type of log requested.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Buggy guest can write a message that advertises more data that
is provided. As QEMU internally duplicates the reported message
size, this may result in an out of bounds access.
Add sanity checks on the size to avoid this.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Buggy software might write a message that is too short for
either the header, or the header + the event data that is specified
in the header. This may result in accesses beyond the range of the
message allocated as a duplicate of the incoming message buffer.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cxl_cmd_dcd_release_dyn_cap() and cmd_dcd_add_dyn_cap_rsp() are missing
input message size checks. These must be done in the individual
commands when the command has a variable length input payload.
A buggy or malicious guest might send undersized messages via the mailbox.
As that size is used to take a copy of the mailbox content, each command
must check there is sufficient data. In this case the first check is that
there is enough data to read how many extents there are, and the second
that there is enough for those elements to be accessed.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the function of retrieving DC extents (cmd_dcd_get_dyn_cap_ext_list),
the output buffer index was not correctly updated while iterating the
extent list on the device, leaving the extents returned incorrect except for
the first one.
Fixes: 1c9221f19e ("hw/mem/cxl_type3: Add DC extent list representative and get DC extent list mailbox support")
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101132005.26633-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL spec 3.1 section 8.2.9.9.11.2 describes the DDR5 Error Check Scrub (ECS)
control feature.
ECS log capabilities field in following ECS tables, which is common for all
memory media FRUs in a CXL device.
Fix struct CXLMemECSReadAttrs and struct CXLMemECSWriteAttrs to make
log entry type field common.
Fixes: 2d41ce38fb ("hw/cxl/cxl-mailbox-utils: Add device DDR5 ECS control feature")
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
Misc HW patch queue
- Restrict probe_access*() functions to TCG (Phil)
- Extract do_invalidate_device_tlb from vtd_process_device_iotlb_desc (Clément)
- Fixes in Loongson IPI model (Bibo & Phil)
- Make docs/interop/firmware.json compatible with qapi-gen.py script (Thomas)
- Correct MPC I2C MMIO region size (Zoltan)
- Remove useless cast in Loongson3 Virt machine (Yao)
- Various uses of range overlap API (Yao)
- Use ERRP_GUARD macro in nubus_virtio_mmio_realize (Zhao)
- Use DMA memory API in Goldfish UART model (Phil)
- Expose fifo8_pop_buf and introduce fifo8_drop (Phil)
- MAINTAINERS updates (Zhao, Phil)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmagFF8ACgkQ4+MsLN6t
# wN5bKg//f5TwUhsy2ff0FJpHheDOj/9Gc2nZ1U/Fp0E5N3sz3A7MGp91wye6Xwi3
# XG34YN9LK1AVzuCdrEEs5Uaxs1ZS1R2mV+fZaGHwYYxPDdnXxGyp/2Q0eyRxzbcN
# zxE2hWscYSZbPVEru4HvZJKfp4XnE1cqA78fJKMAdtq0IPq38tmQNRlJ+gWD9dC6
# ZUHXPFf3DnucvVuwqb0JYO/E+uJpcTtgR6pc09Xtv/HFgMiS0vKZ1I/6LChqAUw9
# eLMpD/5V2naemVadJe98/dL7gIUnhB8GTjsb4ioblG59AO/uojutwjBSQvFxBUUw
# U5lX9OSn20ouwcGiqimsz+5ziwhCG0R6r1zeQJFqUxrpZSscq7NQp9ygbvirm+wS
# edLc8yTPf4MtYOihzPP9jLPcXPZjEV64gSnJISDDFYWANCrysX3suaFEOuVYPl+s
# ZgQYRVSSYOYHgNqBSRkPKKVUxskSQiqLY3SfGJG4EA9Ktt5lD1cLCXQxhdsqphFm
# Ws3zkrVVL0EKl4v/4MtCgITIIctN1ZJE9u3oPJjASqSvK6EebFqAJkc2SidzKHz0
# F3iYX2AheWNHCQ3HFu023EvFryjlxYk95fs2f6Uj2a9yVbi813qsvd3gcZ8t0kTT
# +dmQwpu1MxjzZnA6838R6OCMnC+UpMPqQh3dPkU/5AF2fc3NnN8=
# =J/I2
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 24 Jul 2024 06:36:47 AM AEST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
* tag 'hw-misc-20240723' of https://github.com/philmd/qemu: (28 commits)
MAINTAINERS: Add myself as a reviewer of machine core
MAINTAINERS: Cover guest-agent in QAPI schema
util/fifo8: Introduce fifo8_drop()
util/fifo8: Expose fifo8_pop_buf()
util/fifo8: Rename fifo8_pop_buf() -> fifo8_pop_bufptr()
util/fifo8: Rename fifo8_peek_buf() -> fifo8_peek_bufptr()
util/fifo8: Use fifo8_reset() in fifo8_create()
util/fifo8: Fix style
chardev/char-fe: Document returned value on error
hw/char/goldfish: Use DMA memory API
hw/nubus/virtio-mmio: Fix missing ERRP_GUARD() in realize handler
dump: make range overlap check more readable
crypto/block-luks: make range overlap check more readable
system/memory_mapping: make range overlap check more readable
sparc/ldst_helper: make range overlap check more readable
cxl/mailbox: make range overlap check more readable
util/range: Make ranges_overlap() return bool
hw/mips/loongson3_virt: remove useless type cast
hw/i2c/mpc_i2c: Fix mmio region size
docs/interop/firmware.json: convert "Example" section
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Implement transfer and activate functionality per 3.1 spec for
supporting update metadata (no actual buffers). Transfer times
are arbitrarily set to ten and two seconds for full and part
transfers, respectively.
cxl update-firmware mem0 -F fw.img
<on-going fw update>
cxl update-firmware mem0
"memdev":"mem0",
"pmem_size":"1024.00 MiB (1073.74 MB)",
"serial":"0",
"host":"0000:0d:00.0",
"firmware":{
"num_slots":2,
"active_slot":1,
"online_activate_capable":true,
"slot_1_version":"BWFW VERSION 0",
"fw_update_in_progress":true,
"remaining_size":22400
}
}
<completed fw update>
cxl update-firmware mem0
{
"memdev":"mem0",
"pmem_size":"1024.00 MiB (1073.74 MB)",
"serial":"0",
"host":"0000:0d:00.0",
"firmware":{
"num_slots":2,
"active_slot":1,
"staged_slot":2,
"online_activate_capable":true,
"slot_1_version":"BWFW VERSION 0",
"slot_2_version":"BWFW VERSION 1",
"fw_update_in_progress":false
}
}
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20240627164912.25630-1-dave@stgolabs.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240705125915.991672-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL spec 3.1 section 8.2.9.9.11.2 describes the DDR5 Error Check Scrub (ECS)
control feature.
The Error Check Scrub (ECS) is a feature defined in JEDEC DDR5 SDRAM
Specification (JESD79-5) and allows the DRAM to internally read, correct
single-bit errors, and write back corrected data bits to the DRAM array
while providing transparency to error counts. The ECS control feature
allows the request to configure ECS input configurations during system
boot or at run-time.
The ECS control allows the requester to change the log entry type, the ECS
threshold count provided that the request is within the definition
specified in DDR5 mode registers, change mode between codeword mode and
row count mode, and reset the ECS counter.
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Link: https://lore.kernel.org/r/20240223085902.1549-4-shiju.jose@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240705123039.963781-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL spec 3.1 section 8.2.9.9.11.1 describes the device patrol scrub control
feature. The device patrol scrub proactively locates and makes corrections
to errors in regular cycle. The patrol scrub control allows the request to
configure patrol scrub input configurations.
The patrol scrub control allows the requester to specify the number of
hours for which the patrol scrub cycles must be completed, provided that
the requested number is not less than the minimum number of hours for the
patrol scrub cycle that the device is capable of. In addition, the patrol
scrub controls allow the host to disable and enable the feature in case
disabling of the feature is needed for other purposes such as
performance-aware operations which require the background operations to be
turned off.
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Link: https://lore.kernel.org/r/20240223085902.1549-3-shiju.jose@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240705123039.963781-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The spec states that reads/writes should have no effect and a part of
commands should be ignored when the media is disabled, not when the
sanitize command is running.
Introduce cxl_dev_media_disabled() to check if the media is disabled and
replace sanitize_running() with it.
Make sure that the media has been correctly disabled during sanitation
by adding an assert to __toggle_media(). Now, enabling when already
enabled or vice versa results in an assert() failure.
Suggested-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Link: https://lore.kernel.org/r/20231222090051.3265307-4-42.hyeyoo@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240705120643.959422-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All DPA ranges in the DC regions are invalid to access until an extent
covering the range has been successfully accepted by the host. A bitmap
is added to each region to record whether a DC block in the region has
been backed by a DC extent. Each bit in the bitmap represents a DC block.
When a DC extent is accepted, all the bits representing the blocks in the
extent are set, which will be cleared when the extent is released.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-13-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To simulate FM functionalities for initiating Dynamic Capacity Add
(Opcode 5604h) and Dynamic Capacity Release (Opcode 5605h) as in CXL spec
r3.1 7.6.7.6.5 and 7.6.7.6.6, we implemented two QMP interfaces to issue
add/release dynamic capacity extents requests.
With the change, we allow to release an extent only when its DPA range
is contained by a single accepted extent in the device. That is to say,
extent superset release is not supported yet.
1. Add dynamic capacity extents:
For example, the command to add two continuous extents (each 128MiB long)
to region 0 (starting at DPA offset 0) looks like below:
{ "execute": "qmp_capabilities" }
{ "execute": "cxl-add-dynamic-capacity",
"arguments": {
"path": "/machine/peripheral/cxl-dcd0",
"host-id": 0,
"selection-policy": "prescriptive",
"region": 0,
"extents": [
{
"offset": 0,
"len": 134217728
},
{
"offset": 134217728,
"len": 134217728
}
]
}
}
2. Release dynamic capacity extents:
For example, the command to release an extent of size 128MiB from region 0
(DPA offset 128MiB) looks like below:
{ "execute": "cxl-release-dynamic-capacity",
"arguments": {
"path": "/machine/peripheral/cxl-dcd0",
"host-id": 0,
"removal-policy":"prescriptive",
"region": 0,
"extents": [
{
"offset": 134217728,
"len": 134217728
}
]
}
}
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-12-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per CXL spec 3.1, two mailbox commands are implemented:
Add Dynamic Capacity Response (Opcode 4802h) 8.2.9.9.9.3, and
Release Dynamic Capacity (Opcode 4803h) 8.2.9.9.9.4.
For the process of the above two commands, we use two-pass approach.
Pass 1: Check whether the input payload is valid or not; if not, skip
Pass 2 and return mailbox process error.
Pass 2: Do the real work--add or release extents, respectively.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-11-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add (file/memory backed) host backend for DCD. All the dynamic capacity
regions will share a single, large enough host backend. Set up address
space for DC regions to support read/write operations to dynamic capacity
for DCD.
With the change, the following support is added:
1. Add a new property to type3 device "volatile-dc-memdev" to point to host
memory backend for dynamic capacity. Currently, all DC regions share one
host backend;
2. Add namespace for dynamic capacity for read/write support;
3. Create cdat entries for each dynamic capacity region.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-9-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per cxl spec r3.1, add dynamic capacity (DC) region representative based on
Table 8-165 and extend the cxl type3 device definition to include DC region
information. Also, based on info in 8.2.9.9.9.1, add 'Get Dynamic Capacity
Configuration' mailbox support.
Note: we store region decode length as byte-wise length on the device, which
should be divided by 256 * MiB before being returned to the host
for "Get Dynamic Capacity Configuration" mailbox command per
specification.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-5-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This enables wrapper devices to customize the base device's CCI
(for example, with custom commands outside the specification)
without the need to change the base device.
The also enabled the base device to dispatch those commands without
requiring additional driver support.
Heavily edited by Jonathan Cameron to increase code reuse
Signed-off-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-3-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows devices to have fully customized CCIs, along with complex
devices where wrapper devices can override or add additional CCI
commands without having to replicate full command structures or
pollute a base device with every command that might ever be used.
Signed-off-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-2-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_fixed_memory_window_config(), @errp is dereferenced in 2
places without ERRP_GUARD():
fw->enc_int_ways = cxl_interleave_ways_enc(fw->num_targets, errp);
if (*errp) {
return;
}
and
fw->enc_int_gran =
cxl_interleave_granularity_enc(object->interleave_granularity,
errp);
if (*errp) {
return;
}
For the above 2 places, we check "*errp", because neither function
returns a suitable error code. And since machine_set_cfmw() - the caller
of cxl_fixed_memory_window_config() - doesn't get the NULL @errp
parameter as the "set" method of object property,
cxl_fixed_memory_window_config() hasn't triggered the bug that
dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_fixed_memory_window_config().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When setting GLIB_VERSION_MAX_ALLOWED to GLIB_VERSION_2_58 or higher
(which we'll certainly do in the not too distant future), glib adds
type safety checks to the g_steal_pointer() macro. This trigger an
error in the ct3_load_cdat() function: The local char *buf variable is
assigned to uint8_t *buf in CDATObject, i.e. a pointer of a different
type. Change the local variable to the same type as buf in CDATObject
to avoid the error.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>