Add '-drive' support to OTP device. Allow users to assign a raw file
as OTP image.
test commands for 16k otp.img filled with zero:
$ dd if=/dev/zero of=./otp.img bs=1k count=16
$ ./qemu-system-riscv64 -M sifive_u -m 256M -nographic -bios none \
-kernel ../opensbi/build/platform/sifive/fu540/firmware/fw_payload.elf \
-d guest_errors -drive if=none,format=raw,file=otp.img
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201020033732.12921-3-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently a single watch on /local/domain/X/backend is registered by each
QEMU process running in service domain X (where X is usually 0). The purpose
of this watch is to ensure that QEMU is notified when the Xen toolstack
creates a new device backend area.
Such a backend area is specific to a single frontend area created for a
specific guest domain and, since each QEMU process is also created to service
a specfic guest domain, it is unnecessary and inefficient to notify all QEMU
processes.
Only the QEMU process associated with the same guest domain need
receive the notification. This patch re-factors the watch registration code
such that notifications are targetted appropriately.
Reported-by: Jerome Leseinne <jerome.leseinne@gmail.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201001081500.1026-1-paul@xen.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
qemu-macppc updates
# gpg: Signature made Mon 19 Oct 2020 08:13:16 BST
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-macppc-20201019:
mac_oldworld: Change PCI address of macio to match real hardware
mac_oldworld: Drop some variables
mac_oldworld: Drop a variable, use get_system_memory() directly
mac_newworld: Allow loading binary ROM image
mac_oldworld: Allow loading binary ROM image
m48t59: remove legacy m48t59_init() function
ppc405_boards: use qdev properties instead of legacy m48t59_init() function
sun4u: use qdev properties instead of legacy m48t59_init() function
sun4m: use qdev properties instead of legacy m48t59_init() function
m48t59-isa: remove legacy m48t59_init_isa() function
uninorth: use qdev gpios for PCI IRQs
grackle: use qdev gpios for PCI IRQs
macio: don't reference serial_hd() directly within the device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MIPS patches queue
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
# gpg: Signature made Sat 17 Oct 2020 14:59:53 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20201017: (44 commits)
target/mips: Increase number of TLB entries on the 34Kf core (16 -> 64)
MAINTAINERS: Remove duplicated Malta test entries
MAINTAINERS: Downgrade MIPS Boston to 'Odd Fixes', fix Paul Burton mail
MAINTAINERS: Put myself forward for MIPS target
MAINTAINERS: Remove myself
docs/system: Update MIPS CPU documentation
tests/acceptance: Add MIPS record/replay tests
hw/mips: Remove exit(1) in case of missing ROM
hw/mips: Rename TYPE_MIPS_BOSTON to TYPE_BOSTON
hw/mips: Simplify code using ROUND_UP(INITRD_PAGE_SIZE)
hw/mips: Simplify loading 64-bit ELF kernels
hw/mips/malta: Use clearer qdev style
hw/mips/malta: Move gt64120 related code together
hw/mips/malta: Fix FPGA I/O region size
target/mips/cpu: Display warning when CPU is used without input clock
hw/mips/cps: Do not allow use without input clock
hw/mips/malta: Set CPU frequency to 320 MHz
hw/mips/boston: Set CPU frequency to 1 GHz
hw/mips/cps: Expose input clock and connect it to CPU cores
hw/mips/jazz: Correct CPU frequencies
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently an object link property is used to pass a reference to the OpenPIC
into the PCI host bridge so that pci_unin_init_irqs() can connect the PCI
IRQs to the PIC itself.
This can be simplified by defining the PCI IRQs as qdev gpios and then wiring
up the PCI IRQs to the PIC in the New World machine init function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201013114922.2946-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of using a INITRD_PAGE_MASK definition, use the
simpler INITRD_PAGE_SIZE one which allows us to simplify
the code by using directly the self-explicit ROUND_UP()
macro.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200927163943.614604-3-f4bug@amsat.org>
This function creates a clock and parents it to another object with a
given name. It calls clock_setup_canonical_path before returning the
new clock.
This function is useful to create clocks in devices when one doesn't
want to expose it at the qdev level (as an input or an output).
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201010135759.437903-4-luc@lmichel.fr>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Implement the ability of marking some versions deprecated. When
that CPU model is chosen, print a warning. The warning message
can be customized, e.g. suggesting an alternative CPU model to be
used instead.
The deprecation message will be printed by x86_cpu_list_entry(),
e.g. '-cpu help'.
QMP command 'query-cpu-definitions' will return a bool value
indicating the deprecation status.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1600758855-80046-1-git-send-email-robert.hu@linux.intel.com>
[ehabkost: reword commit message]
[ehabkost: Handle NULL cpu_type]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some code might race with placement of new devices on a bus.
We currently first place a (unrealized) device on the bus
and then realize it.
As a workaround, users that scan the child device list, can
check the realized property to see if it is safe to access such a device.
Use an atomic write here too to aid with this.
A separate discussion is what to do with devices that are unrealized:
It looks like for this case we only call the hotplug handler's unplug
callback and its up to it to unrealize the device.
An atomic operation doesn't cause harm for this code path though.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the race between device emulation code that tries to find
a child device to dispatch the request to (e.g a scsi disk),
and hotplug of a new device to that bus.
Note that this doesn't convert all the readers of the list
but only these that might go over that list without BQL held.
This is a very small first step to make this code thread safe.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-5-mlevitsk@redhat.com>
[Use RCU_READ_LOCK_GUARD in more places, adjust testcase now that
the delay in DEVICE_DELETED due to RCU is more consistent. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-9-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check if an address is free on the bus before plugging in the
device. This makes it possible to do the check without any
side effects, and to detect the problem early without having
to do it in the realize callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some objects accidentally inherit ObjectClass instead of Object.
They compile silently but may crash after downcasting.
In this patch, we introduce a coccinelle script to find broken
declarations and fix them manually with proper base type.
Signed-off-by: Sergey Nizovtsev <snizovtsev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The changes to come to NUMA support are all guest visible. In
theory we could just create a new 5_1 class option flag to
avoid the changes to cascade to 5.1 and under. The reality is that
these changes are only relevant if the machine has more than one
NUMA node. There is no need to change guest behavior that has
been around for years needlesly.
This new helper will be used by the next patches to determine
whether we should retain the (soon to be) legacy NUMA behavior
in the pSeries machine. The new behavior will only be exposed
if:
- machine is pseries-5.2 and newer;
- more than one NUMA node is declared in NUMA state.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20201007172849.302240-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm: uses the generic handler
qtest: uses the generic handler
whpx: changed to use the generic handler (identical implementation)
hax: changed to use the generic handler (identical implementation)
hvf: changed to use the generic handler (identical implementation)
tcg: adapt tcg-cpus to point to the tcg-specific handler
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DIAGNOSE 0x318 (diag318) is an s390 instruction that allows the storage
of diagnostic information that is collected by the firmware in the case
of hardware/firmware service events.
QEMU handles the instruction by storing the info in the CPU state. A
subsequent register sync will communicate the data to the hypervisor.
QEMU handles the migration via a VM State Description.
This feature depends on the Extended-Length SCCB (els) feature. If
els is not present, then a warning will be printed and the SCLP bit
that allows the Linux kernel to execute the instruction will not be
set.
Availability of this instruction is determined by byte 134 (aka fac134)
bit 0 of the SCLP Read Info block. This coincidentally expands into the
space used for CPU entries, which means VMs running with the diag318
capability may not be able to read information regarding all CPUs
unless the guest kernel supports an extended-length SCCB.
This feature is not supported in protected virtualization mode.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-9-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As more features and facilities are added to the Read SCP Info (RSCPI)
response, more space is required to store them. The space used to store
these new features intrudes on the space originally used to store CPU
entries. This means as more features and facilities are added to the
RSCPI response, less space can be used to store CPU entries.
With the Extended-Length SCCB (ELS) facility, a KVM guest can execute
the RSCPI command and determine if the SCCB is large enough to store a
complete reponse. If it is not large enough, then the required length
will be set in the SCCB header.
The caller of the SCLP command is responsible for creating a
large-enough SCCB to store a complete response. Proper checking should
be in place, and the caller should execute the command once-more with
the large-enough SCCB.
This facility also enables an extended SCCB for the Read CPU Info
(RCPUI) command.
When this facility is enabled, the boundary violation response cannot
be a result from the RSCPI, RSCPI Forced, or RCPUI commands.
In order to tolerate kernels that do not yet have full support for this
feature, a "fixed" offset to the start of the CPU Entries within the
Read SCP Info struct is set to allow for the original 248 max entries
when this feature is disabled.
Additionally, this is introduced as a CPU feature to protect the guest
from migrating to a machine that does not support storing an extended
SCCB. This could otherwise hinder the VM from being able to read all
available CPU entries after migration (such as during re-ipl).
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-7-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The header contained within the SCCB passed to the SCLP service call
contains the actual length of the SCCB. Instead of allocating a static
4K size for the work sccb, let's allow for a variable size determined
by the value in the header. The proper checks are already in place to
ensure the SCCB length is sufficent to store a full response and that
the length does not cross any explicitly-set boundaries.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-4-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
(In QEMU, we call this the "select" register.)
My memory isn't good enough to memorize what these magic runes
do. Label them to prevent mixups from happening in the future.
Side note: I assume it's safe to always set 0xA0 even though ATA2 claims
these bits are reserved, because ATA3 immediately reinstated that these
bits should be always on. ATA4 and subsequent specs only claim that the
fields are obsolete, so I assume it's safe to leave these set and that
it should work with the widest array of guests.
Signed-off-by: John Snow <jsnow@redhat.com>
I have been staring at this FIXME for years and I never knew what it
meant. I finally stumbled across it!
When writing to the command registers, the old value is shifted into a
HOB copy of the register and the new value is written into the primary
register. When reading registers, the value retrieved is dependent on
the HOB bit in the CONTROL register.
By setting bit 7 (0x80) in CONTROL, any register read will, if it has
one, yield the HOB value for that register instead.
Our code has a problem: We were using bit 7 of the DEVICE register to
model this. We use bus->cmd roughly as the control register already, as
it stores the value from ide_ctrl_write.
Lastly, all command register writes reset the HOB, so fix that, too.
Signed-off-by: John Snow <jsnow@redhat.com>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
