The system controller on PolarFire SoC is access via a mailbox. The
control registers for this mailbox lie in the "IOSCB" region & the
interrupt is cleared via write to the "SYSREG" region. It also has a
QSPI controller, usually connected to a flash chip, that is used for
storing FPGA bitstreams and used for In-Application Programming (IAP).
Linux has an implementation of the system controller, through which the
hwrng is accessed, leading to load/store access faults.
Add the QSPI as unimplemented and a very basic (effectively
unimplemented) version of the system controller's mailbox. Rather than
purely marking the regions as unimplemented, service the mailbox
requests by reporting failures and raising the interrupt so a guest can
better handle the lack of support.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221117225518.4102575-4-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Fabric Interconnect Controllers provide interfaces between the FPGA
fabric and the core complex. There are 5 FICs on PolarFire SoC, numbered
0 through 4. FIC2 is an AXI4 slave interface from the FPGA fabric and
does not show up on the MSS memory map. FIC4 is dedicated to the User
Crypto Processor and does not show up on the MSS memory map either.
FIC 0, 1 & 3 do show up in the MSS memory map and neither FICs 0 or 1
are represented in QEMU, leading to load access violations while booting
Linux for Icicle if PCIe is enabled as the root port is connected via
either FIC 0 or 1.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-3-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On PolarFire SoC, some peripherals (eg the PCI root port) are clocked by
"Clock Conditioning Circuitry" in the FPGA. The specific clock depends
on the FPGA bitstream & can be locked to one particular {D,P}LL - in the
Icicle Kit Reference Design v2022.09 or later this is/will be the case.
Linux v6.1+ will have a driver for this peripheral and devicetrees that
previously relied on "fixed-frequency" clock nodes have been switched
over to clock-controller nodes. The IOSCB region is represented in QEMU,
but the specific region of it that the CCCs occupy has not so v6.1-rcN
kernels fail to boot in QEMU.
Add the regions as unimplemented so that the status-quo in terms of boot
is maintained.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-2-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 40244040a7 changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
-machine kernel-irqchip=off is broken for many guest OSes; kernel-irqchip=split
is the replacement that works, so remove the deprecated support for the former.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows attaching IDE_CFATA device to an IDE bus. Behaves like a
CompactFlash card in True IDE mode.
Tested with:
qemu-system-i386 \
-device driver=ide-cf,drive=cf,bus=ide.0 \
-drive id=cf,index=0,format=raw,if=none,file=cf.img
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Message-Id: <20221130120319.706885-1-lkundrak@v3.sk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While we initialize this value in cpu_common_reset, that
isn't called during startup, so set it as well in init.
This fixes -singlestep versus the very first TB.
Fixes: 04f5b647ed ("accel/tcg: Handle -singlestep in curr_cflags")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Size is used at lines 1088/1188 for the loop, which reads the last 4
bytes from the crc_ptr so it does need to get increased, however it
shouldn't be increased before the buffer is passed to CRC computation,
or the crc32 function will access uninitialized memory.
This was pointed out to me by clg@kaod.org during the code review of
a similar patch to hw/net/ftgmac100.c
Change-Id: Ib0464303b191af1e28abeb2f5105eb25aadb5e9b
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20221221183202.3788132-1-slongfield@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using Clang ("Apple clang version 14.0.0 (clang-1400.0.29.202)")
and building with -Wall we get:
hw/arm/smmu-common.c:173:33: warning: static function 'smmu_hash_remove_by_asid_iova' is used in an inline function with external linkage [-Wstatic-in-inline]
hw/arm/smmu-common.h:170:1: note: use 'static' to give inline function 'smmu_iotlb_inv_iova' internal linkage
void smmu_iotlb_inv_iova(SMMUState *s, int asid, dma_addr_t iova,
^
static
None of our code base require / use inlined functions with external
linkage. Some places use internal inlining in the hot path. These
two functions are certainly not in any hot path and don't justify
any inlining, so these are likely oversights rather than intentional.
Reported-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221216214924.4711-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hi,
"Host Memory Backends" and "Memory devices" queue ("mem"):
- virtio-mem fixes
- Use new MPOL_PREFERRED_MANY mbind() policy for memory backends if
possible
# gpg: Signature made Mon 02 Jan 2023 11:22:04 GMT
# gpg: using RSA key 1BD9CAAD735C4C3A460DFCCA4DDE10F700FF835A
# gpg: issuer "david@redhat.com"
# gpg: Good signature from "David Hildenbrand <david@redhat.com>" [marginal]
# gpg: aka "David Hildenbrand <davidhildenbrand@gmail.com>" [full]
# gpg: aka "David Hildenbrand <hildenbr@in.tum.de>" [unknown]
# Primary key fingerprint: 1BD9 CAAD 735C 4C3A 460D FCCA 4DDE 10F7 00FF 835A
* tag 'mem-2023-01-02' of https://github.com/davidhildenbrand/qemu:
hostmem: Honor multiple preferred nodes if possible
virtio-mem: Fix typo in function name
virtio-mem: Fix the iterator variable in a vmem->rdl_list loop
virtio-mem: Fix the bitmap index of the section offset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- fix#1263 for CR writes
- rework compare time handling
- The compare timer has to run even if CR.OCIEN is not set,
as SR.OCIF must be updated.
- The compare timer fires exactly once when the
compare value is less than the current value, but the
reload values is less than the compare value.
- The compare timer will never fire if the reload value is
less than the compare value. Disable it in this case.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
[PMM: fixed minor style nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CNT register is a read-only register. There is no need to
store it's value, it can be calculated on demand.
The calculated frequency is needed temporarily only.
Note that this is a migration compatibility break for all boards
types that use the EPIT peripheral.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qemu_v9fs_synth_mkdir() and qemu_v9fs_synth_add_file() functions
currently return a positive errno value on failure. This causes
checkpatch.pl to spit several errors like the one below:
ERROR: return of an errno should typically be -ve (return -EAGAIN)
+ return EAGAIN;
Simply change the sign. This has no consequence since callers
assert() the returned value to be equal to 0.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <166930551818.827792.10663674346122681963.stgit@bahia>
[C.S.: - Resolve conflict with 66997c42e0. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
ppc patch queue for 2022-12-21:
This queue contains a MAINTAINERS update, the implementation of the Freescale eSDHC,
the introduction of the DEXCR/HDEXCR instructions and other assorted fixes (most of
them for the e500 board).
# gpg: Signature made Wed 21 Dec 2022 17:18:53 GMT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20221221' of https://gitlab.com/danielhb/qemu:
target/ppc: Check DEXCR on hash{st, chk} instructions
target/ppc: Implement the DEXCR and HDEXCR
hw/ppc/e500: Move comment to more appropriate place
hw/ppc/e500: Resolve variable shadowing
hw/ppc/e500: Prefer local variable over qdev_get_machine()
hw/ppc/virtex_ml507: Prefer local over global variable
target/ppc/mmu_common: Fix table layout of "info tlb" HMP command
target/ppc/mmu_common: Log which effective address had no TLB entry found
hw/ppc/spapr: Reduce "vof.h" inclusion
hw/ppc/vof: Do not include the full "cpu.h"
target/ppc/kvm: Add missing "cpu.h" and "exec/hwaddr.h"
hw/ppc/e500: Add Freescale eSDHC to e500plat
hw/sd/sdhci: Support big endian SD host controller interfaces
MAINTAINERS: downgrade PPC KVM/TCG CPUs and pSeries to 'Odd Fixes'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently objects including "hw/ppc/spapr.h" are forced to be
target specific due to the inclusion of "vof.h" in "spapr.h".
"spapr.h" only uses a Vof pointer, so doesn't require the structure
declaration. The only place where Vof structure is accessed is in
spapr.c, so include "vof.h" there, and forward declare the structure
in "spapr.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221213123550.39302-4-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some SDHCI IP can be synthetized in various endianness:
https://github.com/u-boot/u-boot/blob/v2021.04/doc/README.fsl-esdhc
- CONFIG_SYS_FSL_ESDHC_BE
ESDHC IP is in big-endian mode. Accessing ESDHC registers can be
determined by ESDHC IP's endian mode or processor's endian mode.
Our current implementation is little-endian. In order to support
big endianness:
- Rename current MemoryRegionOps as sdhci_mmio_le_ops ('le')
- Add an 'endianness' property to SDHCIState (default little endian)
- Set the 'io_ops' field in realize() after checking the property
- Add the sdhci_mmio_be_ops (big-endian) MemoryRegionOps.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221101222934.52444-3-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
virtio,pc,pci: features, cleanups, fixes
make TCO watchdog work by default
part of generic vdpa support
asid interrupt for vhost-vdpa
added flex bus port DVSEC for cxl
misc fixes, cleanups, documentation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 21 Dec 2022 12:32:36 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (41 commits)
contrib/vhost-user-blk: Replace lseek64 with lseek
libvhost-user: Switch to unsigned int for inuse field in struct VuVirtq
hw/virtio: Extract QMP related code virtio-qmp.c
hw/virtio: Extract config read/write accessors to virtio-config-io.c
hw/virtio: Constify qmp_virtio_feature_map_t[]
hw/virtio: Guard and restrict scope of qmp_virtio_feature_map_t[]
hw/virtio: Rename virtio_ss[] -> specific_virtio_ss[]
hw/virtio: Add missing "hw/core/cpu.h" include
hw/cxl/device: Add Flex Bus Port DVSEC
hw/acpi: Rename tco.c -> ich9_tco.c
acpi/tests/avocado/bits: add mformat as one of the dependencies
docs/acpi/bits: document BITS_DEBUG environment variable
pci: drop redundant PCIDeviceClass::is_bridge field
remove DEC 21154 PCI bridge
vhost: fix vq dirty bitmap syncing when vIOMMU is enabled
acpi/tests/avocado/bits: add SPDX license identifiers for bios bits tests
include/hw: attempt to document VirtIO feature variables
vhost-user: send set log base message only once
vdpa: always start CVQ in SVQ mode if possible
vdpa: add shadow_data to vhost_vdpa
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
