This new behaviour is in the ARM pseudocode function
AArch64.CheckFPAdvSIMDEnabled, which applies to AArch32
via AArch32.CheckAdvSIMDOrFPEnabled when the EL to which
the trap would be delivered is in AArch64 mode.
Given that ARMv9 drops support for AArch32 outside EL0, the trap EL
detection ought to be trivially true, but the pseudocode still contains
a number of conditions, and QEMU has not yet committed to dropping A32
support for EL[12] when v9 features are present.
Since the computation of SME_TRAP_NONSTREAMING is necessarily different
for the two modes, we might as well preserve bits within TBFLAG_ANY and
allocate separate bits within TBFLAG_A32 and TBFLAG_A64 instead.
Note that DDI0616A.a has typos for bits [22:21] of LD1RO in the table
of instructions illegal in streaming mode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 39a1fd2528 we fixed a bug in the handling of LPAE block
descriptors where we weren't correctly zeroing out some RES0 bits.
However this fix has a bug because the calculation of the mask is
done at the wrong width: in
descaddr &= ~(page_size - 1);
page_size is a target_ulong, so in the 'qemu-system-arm' binary it is
only 32 bits, and the effect is that we always zero out the top 32
bits of the calculated address. Fix the calculation by forcing the
mask to be calculated with the same type as descaddr.
This only affects 32-bit CPUs which support LPAE (e.g. cortex-a15)
when used on board models which put RAM or devices above the 4GB
mark and when the 'qemu-system-arm' executable is being used.
It was also masked in 7.0 by the main bug reported in
https://gitlab.com/qemu-project/qemu/-/issues/1078 where the
virt board incorrectly does not enable 'highmem' for 32-bit CPUs.
The workaround is to use 'qemu-system-aarch64' with the same
command line.
Reported-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220627134620.3190252-1-peter.maydell@linaro.org
Fixes: 39a1fd2528 ("target/arm: Fix handling of LPAE block descriptors")
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The architecture defines the OS DoubleLock as a register which
(similarly to the OS Lock) suppresses debug events for use in CPU
powerdown sequences. This functionality is required in Arm v7 and
v8.0; from v8.2 it becomes optional and in v9 it must not be
implemented.
Currently in QEMU we implement the OSDLR_EL1 register as a NOP. This
is wrong both for the "feature implemented" and the "feature not
implemented" cases: if the feature is implemented then the DLK bit
should read as written and cause suppression of debug exceptions, and
if it is not implemented then the bit must be RAZ/WI.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Starting with v7 of the debug architecture, there are three extra
ID registers that add information on top of that provided in
DBGDIDR. These are DBGDEVID, DBGDEVID1 and DBGDEVID2. In the
v7 debug architecture, DBGDEVID is optional, present only of
DBGDIDR.DEVID_imp is set. In v7.1 all three must be present.
Implement the missing registers. Note that we only need to set the
values in the ARMISARegisters struct for the CPUs Cortex-A7, A15,
A53, A57 and A72 (plus the 32-bit 'max' which uses the Cortex-A53
values): earlier CPUs didn't implement v7 of the architecture, and
our other 64-bit CPUs (Cortex-A76, Neoverse-N1 and A64fx) don't have
AArch32 support at EL1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220630194116.3438513-5-peter.maydell@linaro.org
The "OS Lock" in the Arm debug architecture is a way for software
to suppress debug exceptions while it is trying to power down
a CPU and save the state of the breakpoint and watchpoint
registers. In QEMU we implemented the support for writing
the OS Lock bit via OSLAR_EL1 and reading it via OSLSR_EL1,
but didn't implement the actual behaviour.
The required behaviour with the OS Lock set is:
* debug exceptions (apart from BKPT insns) are suppressed
* some MDSCR_EL1 bits allow write access to the corresponding
EDSCR external debug status register that they shadow
(we can ignore this because we don't implement external debug)
* similarly with the OSECCR_EL1 which shadows the EDECCR
(but we don't implement OSECCR_EL1 anyway)
Implement the missing behaviour of suppressing debug
exceptions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220630194116.3438513-4-peter.maydell@linaro.org
The target/arm/helper.c file is very long and is a grabbag of all
kinds of functionality. We have already a debug_helper.c which has
code for implementing architectural debug. Move the code which
defines the debug-related system registers out to this file also.
This affects the define_debug_regs() function and the various
functions and arrays which are used only by it.
The functions raw_write() and arm_mdcr_el2_eff() and
define_debug_regs() now need to be global rather than local to
helper.c; everything else is pure code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220630194116.3438513-3-peter.maydell@linaro.org
Fixes a bug in that we were not honoring MTE from user-only
SVE. Copy the user-only MTE logic from allocation_tag_mem
into sve_probe_page.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform the cleanup in the FIXME comment in common_semi_gdb_syscall.
Do not modify guest registers until the syscall is complete,
which in the gdbstub case is asynchronous.
In the synchronous non-gdbstub case, use common_semi_set_ret
to set the result. Merge set_swi_errno into common_semi_cb.
Rely on the latter for combined return value / errno setting.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When Streaming SVE mode is enabled, the size is taken from
SMCR_ELx instead of ZCR_ELx. The format is shared, but the
set of vector lengths is not. Further, Streaming SVE does
not require any particular length to be supported.
Adjust sve_vqm1_for_el to pass the current value of PSTATE.SM
to the new function.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mirror the properties for SVE. The main difference is
that any arbitrary set of powers of 2 may be supported,
and not the stricter constraints that apply to SVE.
Include a property to control FEAT_SME_FA64, as failing
to restrict the runtime to the proper subset of insns
could be a major point for bugs.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220620175235.60881-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
