If we build with --without-default-devices, CONFIG_HPET and
CONFIG_PARALLEL are set to N, which makes the respective devices go
missing from acpi tables.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Check that virtio-scsi-pci is present in the QEMU build before running
the tests.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Do not include tests that require devices that are not available in
the QEMU build.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Don't include tests that require devices not available in the QEMU
binary.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This test depends on the presence of the pcie-root-port device. Add a
build time dependency.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The tests are built once for all the targets, so as long as one QEMU
binary is built with CONFIG_LSI_SCSI_PCI=y, this test will
run. However some binaries might not include the device. So check this
again in runtime.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Check if the devices we're trying to add are present in the QEMU
binary. They could have been removed from the build via Kconfig or the
--without-default-devices option.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Migration Pull request (take3)
Hi
In this PULL request:
- Added to leonardo fixes:
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Please apply.
[take 2]
- rebase to latest upstream
- fix compilation of linux-user (if have_system was missing) (me)
- cleanup multifd_load_cleanup(leonardo)
- Document RAM flags (me)
Please apply.
[take 1]
This are all the reviewed patches for migration:
- AVX512 support for xbzrle (Ling Xu)
- /dev/userfaultd support (Peter Xu)
- Improve ordering of channels (Peter Xu)
- multifd cleanups (Li Zhang)
- Remove spurious files from last merge (me)
Rebase makes that to you
- Fix mixup between state_pending_{exact,estimate} (me)
- Cache RAM size during migration (me)
- cleanup several functions (me)
Please apply.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmPppZYACgkQ9IfvGFhy
# 1yPLvQ//f8D6txzFawaxrfzpSAHnq70Gx+B5GkIwgwB8nlPIC3QELEf5uooM/RGA
# nSaUctUNOJUWqVGK3vp3jDIep02DzdIUrlOfy96h+pnTMpyMWFC2BexDfveVMUId
# dw8WCWZkGCFDfIWuKF+GA8eTu6HM1ouzgCJrRmPtCqsikzAPkogPm60hQSTAQxm9
# Kzdp1SXV1HmyA440vy8rtYf71BKpvb9OJFmwgZ+ICy0rc1aUmgJbKxkwyOgiI2lq
# ONekpbOg7lzlFVAQu1QHTmYN13bsn4uzwUgdifn1PixFQyRE3AVs4jdTmqeLnoPe
# Ac6j8v3pDOw/Xf4kpRWUmhkqTMEJt8/lyneJzu1mQkw0wwiUtDvknFgPG8wJsa+J
# ZQr1cBXQj4IjtkN6+ixF7XYvx3T6pWz0L+/w2+TbFBdLWIrPgFH0yPYjhx7FdDid
# cjUHyS1a0w9ngnXOxRG8+UNHWCpPOUhXeeiyNioogYZNKu77PFxJVDMe3eB6dXAB
# pDfl4P129PloKAPafcz9E6Sxr+lIgrETZmsRJlRz4czg18TxlIukMlDtyrepNWti
# GtIf9xTpP3JKjpHnKbWLaxP5VeFC7kQd0qas4VxD+tDjbJdUZdZMfHcOSS0SMRGe
# q5LVEzMMIPCQJQIqiLEJ0HTUUOtB8i+bGoirNEbDqhLa/oZwPP8=
# =TDnO
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 13 Feb 2023 02:51:02 GMT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20230213-pull-request' of https://gitlab.com/juan.quintela/qemu: (22 commits)
ram: Document migration ram flags
migration/multifd: Move load_cleanup inside incoming_state_destroy
migration/multifd: Join all multifd threads in order to avoid leaks
migration/multifd: Remove unnecessary assignment on multifd_load_cleanup()
migration/multifd: Change multifd_load_cleanup() signature and usage
migration: Postpone postcopy preempt channel to be after main
migration: Add a semaphore to count PONGs
migration: Cleanup postcopy_preempt_setup()
migration: Rework multi-channel checks on URI
Update bench-code for addressing CI problem
AVX512 support for xbzrle_encode_buffer
migration: I messed state_pending_exact/estimate
migration: Make ram_save_target_page() a pointer
migration: Calculate ram size once
migration: Split ram_bytes_total_common() in two functions
migration: Make find_dirty_block() return a single parameter
migration: Simplify ram_find_and_save_block()
util/userfaultfd: Support /dev/userfaultfd
linux-headers: Update to v6.1
multifd: Remove some redundant code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
0x80 is RAM_SAVE_FLAG_HOOK, it is in qemu-file now.
Bigger usable flag is 0x200, noticing that.
We can reuse RAM_SAVe_FLAG_FULL.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Currently running migration_incoming_state_destroy() without first running
multifd_load_cleanup() will cause a yank error:
qemu-system-x86_64: ../util/yank.c:107: yank_unregister_instance:
Assertion `QLIST_EMPTY(&entry->yankfns)' failed.
(core dumped)
The above error happens in the target host, when multifd is being used
for precopy, and then postcopy is triggered and the migration finishes.
This will crash the VM in the target host.
To avoid that, move multifd_load_cleanup() inside
migration_incoming_state_destroy(), so that the load cleanup becomes part
of the incoming state destroying process.
Running multifd_load_cleanup() twice can become an issue, though, but the
only scenario it could be ran twice is on process_incoming_migration_bh().
So removing this extra call is necessary.
On the other hand, this multifd_load_cleanup() call happens way before the
migration_incoming_state_destroy() and having this happening before
dirty_bitmap_mig_before_vm_start() and vm_start() may be a need.
So introduce a new function multifd_load_shutdown() that will mainly stop
all multifd threads and close their QIOChannels. Then use this function
instead of multifd_load_cleanup() to make sure nothing else is received
before dirty_bitmap_mig_before_vm_start().
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Current approach will only join threads that are still running.
For the threads not joined, resources or private memory are always kept in
the process space and never reclaimed before process end, and this risks
serious memory leaks.
This should usually not represent a big problem, since multifd migration
is usually just ran at most a few times, and after it succeeds there is
not much to be done before exiting the process.
Yet still, it should not hurt performance to join all of them.
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Before assigning "p->quit = true" for every multifd channel,
multifd_load_cleanup() will call multifd_recv_terminate_threads() which
already does the same assignment, while protected by a mutex.
So there is no point doing the same assignment again.
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since it's introduction in commit f986c3d256 ("migration: Create multifd
migration threads"), multifd_load_cleanup() never returned any value
different than 0, neither set up any error on errp.
Even though, on process_incoming_migration_bh() an if clause uses it's
return value to decide on setting autostart = false, which will never
happen.
In order to simplify the codebase, change multifd_load_cleanup() signature
to 'void multifd_load_cleanup(void)', and for every usage remove error
handling or decision made based on return value != 0.
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Postcopy with preempt-mode enabled needs two channels to communicate. The
order of channel establishment is not guaranteed. It can happen that the
dest QEMU got the preempt channel connection request before the main
channel is established, then the migration may make no progress even during
precopy due to the wrong order.
To fix it, create the preempt channel only if we know the main channel is
established.
For a general postcopy migration, we delay it until postcopy_start(),
that's where we already went through some part of precopy on the main
channel. To make sure dest QEMU has already established the channel, we
wait until we got the first PONG received. That's something we do at the
start of precopy when postcopy enabled so it's guaranteed to happen sooner
or later.
For a postcopy recovery, we delay it to qemu_savevm_state_resume_prepare()
where we'll have round trips of data on bitmap synchronizations, which
means the main channel must have been established.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This is mostly useless, but useful for us to know whether the main channel
is correctly established without changing the migration protocol.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since we just dropped the only case where postcopy_preempt_setup() can
return an error, it doesn't need a retval anymore because it never fails.
Move the preempt check to the caller, preparing it to be used elsewhere to
do nothing but as simple as kicking the async connection.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The whole idea of multi-channel checks was not properly done, IMHO.
Currently we check multi-channel in a lot of places, but actually that's
not needed because we only need to check it right after we get the URI and
that should be it.
If the URI check succeeded, we should never need to check it again because
we must have it. If it check fails, we should fail immediately on either
the qmp_migrate or qmp_migrate_incoming, instead of failingg it later after
the connection established.
Neither should we fail any set capabiliities like what we used to do here:
5ad15e8614 ("migration: allow enabling mutilfd for specific protocol only", 2021-10-19)
Because logically the URI will only be set later after the capability is
set, so it doesn't make a lot of sense to check the URI type when setting
the capability, because we're checking the cap with an old URI passed in,
and that may not even be the URI we're going to use later.
This patch mostly reverted all such checks for before, dropping the
variable migrate_allow_multi_channels and helpers. Instead, add a common
helper to check URI for multi-channels for either qmp_migrate and
qmp_migrate_incoming and that should do all the proper checks. The failure
will only trigger with the "migrate" or "migrate_incoming" command, or when
user specified "-incoming xxx" where "xxx" is not "defer".
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Unit test code is in test-xbzrle.c, and benchmark code is in xbzrle-bench.c
for performance benchmarking. we have modified xbzrle-bench.c to address
CI problem.
Signed-off-by: ling xu <ling1.xu@intel.com>
Co-authored-by: Zhou Zhao <zhou.zhao@intel.com>
Co-authored-by: Jun Jin <jun.i.jin@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This commit is the same with [PATCH v6 1/2], and provides avx512 support for xbzrle_encode_buffer
function to accelerate xbzrle encoding speed. Runtime check of avx512
support and benchmark for this feature are added. Compared with C
version of xbzrle_encode_buffer function, avx512 version can achieve
50%-70% performance improvement on benchmarking. In addition, if dirty
data is randomly located in 4K page, the avx512 version can achieve
almost 140% performance gain.
Signed-off-by: ling xu <ling1.xu@intel.com>
Co-authored-by: Zhou Zhao <zhou.zhao@intel.com>
Co-authored-by: Jun Jin <jun.i.jin@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I called the helper function from the wrong top level function.
This code was introduced in:
commit c8df4a7aef
Author: Juan Quintela <quintela@redhat.com>
Date: Mon Oct 3 02:00:03 2022 +0200
migration: Split save_live_pending() into state_pending_*
We split the function into to:
- state_pending_estimate: We estimate the remaining state size without
stopping the machine.
- state pending_exact: We calculate the exact amount of remaining
state.
Thanks to Avihai Horon <avihaih@nvidia.com> for finding it.
Fixes:c8df4a7aeffcb46020f610526eea621fa5b0cd47
When we introduced that patch, we enden calling
state_pending_estimate() helper from qemu_savevm_statepending_exact()
and
state_pending_exact() helper from qemu_savevm_statepending_estimate()
This patch fixes it.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We are going to create a new function for multifd latest in the series.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We are recalculating ram size continously, when we know that it don't
change during migration. Create a field in RAMState to track it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It is just a big if in the middle of the function, and we need two
functions anways.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
Reindent to make Phillipe happy (and CODING_STYLE)
We used to return two bools, just return a single int with the
following meaning:
old return / again / new return
false false PAGE_ALL_CLEAN
false true PAGE_TRY_AGAIN
true true PAGE_DIRTY_FOUND /* We don't care about again at all */
Signed-off-by: Juan Quintela <quintela@redhat.com>
We will need later that find_dirty_block() return errors, so
simplify the loop.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Teach QEMU to use /dev/userfaultfd when it existed and fallback to the
system call if either it's not there or doesn't have enough permission.
Firstly, as long as the app has permission to access /dev/userfaultfd, it
always have the ability to trap kernel faults which QEMU mostly wants.
Meanwhile, in some context (e.g. containers) the userfaultfd syscall can be
forbidden, so it can be the major way to use postcopy in a restricted
environment with strict seccomp setup.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I introduced spurious files on my tree during a rebase:
commit ebfc578715
Author: Zhenzhong Duan <zhenzhong.duan@intel.com>
Date: Mon Oct 17 15:53:51 2022 +0800
multifd: Fix flush of zero copy page send request
Make IO channel flush call after the inflight request has been drained
in multifd thread, or else we may missed to flush the inflight request.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To make things worse, it appears like Zhenzhong is the one to blame.
for(int i=0; i < 1000000; i++) {
printf("I will not do rebases when I am tired\n");
}
Sorry, Juan.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The blk_register_buf() API is an optimization hint that allows some
block drivers to avoid I/O buffer housekeeping or bounce buffers.
Add an -r option to register the I/O buffer so that qemu-io can be used
to test the blk_register_buf() API. The next commit will add a test that
uses the new option.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230207203719.242926-4-stefanha@redhat.com>
The block layer APIs use BdrvRequestFlags while qemu-io code uses int.
Although the code compiles and runs fine, BdrvRequestFlags is clearer
because it differentiates between other types of flags like bdrv_open()
flags.
This is purely refactoring.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230207203719.242926-3-stefanha@redhat.com>
When a write request is converted into a write zeroes request by the
detect-zeroes= feature, it is no longer associated with an I/O buffer.
The BDRV_REQ_REGISTERED_BUF flag doesn't make sense without an I/O
buffer and must be cleared because bdrv_co_do_pwrite_zeroes() fails with
-EINVAL when it's set.
Fiona Ebner <f.ebner@proxmox.com> bisected and diagnosed this QEMU 7.2
regression where writes containing zeroes to a blockdev with
discard=unmap,detect-zeroes=unmap fail.
Buglink: https://gitlab.com/qemu-project/qemu/-/issues/1404
Fixes: e8b6535533 ("block: add BDRV_REQ_REGISTERED_BUF request flag")
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230207203719.242926-2-stefanha@redhat.com>
virtio_blk_update_config() calls blk_get_geometry and blk_getlength,
and both functions eventually end up calling bdrv_poll_co when not
running in a coroutine:
- blk_getlength is a co_wrapper_mixed function
- blk_get_geometry calls bdrv_get_geometry -> bdrv_nb_sectors, a
co_wrapper_mixed function too
Since we are not running in a coroutine, we need to take s->blk
AioContext lock, otherwise bdrv_poll_co will inevitably call
AIO_WAIT_WHILE and therefore try to un unlock() an AioContext lock
that was never acquired.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=2167838
Steps to reproduce the issue: simply boot a VM with
-object '{"qom-type":"iothread","id":"iothread1"}' \
-blockdev '{"driver":"file","filename":"$QCOW2","aio":"native","node-name":"libvirt-1-storage","cache":{"direct":true,"no-flush":false},"auto-read-only":true,"discard":"unmap"}' \
-blockdev '{"node-name":"libvirt-1-format","read-only":false,"cache":{"direct":true,"no-flush":false},"driver":"qcow2","file":"libvirt-1-storage"}' \
-device virtio-blk-pci,iothread=iothread1,drive=libvirt-1-format,id=virtio-disk0,bootindex=1,write-cache=on
and observe that it will fail not manage to boot with "qemu_mutex_unlock_impl: Operation not permitted"
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lukáš Doktor <ldoktor@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230208111148.1040083-1-eesposit@redhat.com>
The netdev-socket test intermittently fails on our s390x CI runner:
633/659 ERROR:../tests/qtest/netdev-socket.c:197:test_stream_unix:
assertion failed (resp == expect): ("st0: index=0,type=stream,connection error\r\n" == "st0: index=0,type=stream,unix:/tmp/netdev-socket.GZUG01/stream_unix\r\n")
ERROR
633/659 qemu:qtest+qtest-xtensa / qtest-xtensa/netdev-socket
ERROR 5.47s killed by signal 6 SIGABRT
This may just be because when the machine is under heavy load
running the CI tests it hits the timeout before the QEMU
under test has started to the point of being able to respond
to HMP queries.
Bump the timeout to 60 seconds to see if the intermittent
goes away.
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230207165119.1479132-1-peter.maydell@linaro.org
Header cleanup patches for 2023-02-06
# -----BEGIN PGP SIGNATURE-----
#
# iQJGBAABCAAwFiEENUvIs9frKmtoZ05fOHC0AOuRhlMFAmPjQRUSHGFybWJydUBy
# ZWRoYXQuY29tAAoJEDhwtADrkYZTWHwQAI5D2HTRt3peFSPg/tFuYqSGtOobzM5x
# xdZxjWCtGV+dZ4TsyQ7yJkQ2i6aPjs0LzmTnTIsmf+p1OJSthvp4fQUzfXQauiJy
# OnNA76v7WjiXB8u8tcXtEkkHNmccp8n4KMjk33TfK/HQVx7lZ2EFurlCkvBr5wki
# FuDVad6R43ChmvBWdCUOi6G1IklAihm8AN4lBJu3iC7U8bjW4FmLLMitcu5OyKgt
# v9V4XFAe4eYUIPZ6uH5Lpr5m/qtrRXLe9KOdRUR2vDVL18Cf6Zl7mrUNtv7iV5TI
# hBOA12ZP5XXf81FXl7e8y3Xi2KXvb/el0wQ7SvtE7XB3Pdbfa5WSGKOc3VxYLmBA
# 4xUnEbzAogrrruovdk1bmh2LnVzCH66m72xaLCHBvjOU3M6V2B0eeaZ35FxNuFcB
# toHPAjeuzWkDAscVYcYKuPwnkNOMNqHxEdihrgy6mYLr6nauIYr7Lqgs3SqGqpct
# /HGy683+J+AqnHFTk1MTRftDxqk/Nku6ntAxLXndkpm3uDvu+iV5d3BfK3A9t7d1
# A2Y983DU6SiVwpMIv2eDL8sXYxuwIs56ZmPYIcSbqzpCXtdFqwWOTeFET/4vD+8t
# V3YKJ27jmWQ9bxbLHGPPYSKheuCVBIGsqxouE/Pbj5nXRKm/TeGp+20a4dWdE08r
# 2WTLAQbVQGD4
# =5TPW
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 08 Feb 2023 06:28:37 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-include-2023-02-06-v2' of https://repo.or.cz/qemu/armbru:
Drop duplicate #include
Don't include headers already included by qemu/osdep.h
Fix non-first inclusions of qemu/osdep.h
accel: Clean up includes
block: Clean up includes
riscv: Clean up includes
target/hexagon: Clean up includes
net: Clean up includes
migration: Clean up includes
qga: Clean up includes
hw/tricore: Clean up includes
hw/input: Clean up includes
hw/cxl: Clean up includes
crypto: Clean up includes
bsd-user: Clean up includes
scripts/clean-includes: Improve --git commit message
scripts/clean-includes: Skip symbolic links
scripts/clean-includes: Don't claim duplicate headers found when not
scripts/clean-includes: Fully skip / ignore files
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-17-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230202133830.2152150-16-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-15-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Changes to standalone programs dropped, because these intentionally
don't use qemu/osdep.h:
target/hexagon/gen_dectree_import.c
target/hexagon/gen_semantics.c
target/hexagon/idef-parser/idef-parser.h
target/hexagon/idef-parser/parser-helpers.c
target/hexagon/idef-parser/parser-helpers.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-14-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-13-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230202133830.2152150-12-armbru@redhat.com>
[Straightforward conflict with commit d5890ea072 resolved]
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-11-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-10-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-9-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-8-armbru@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-7-armbru@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-6-armbru@redhat.com>
When a symbolic link points to a file that needs cleaning, the script
replaces the link with a cleaned regular file. Not wanted; skip them.
We have a few symbolic links under subprojects/libvduse/ and
subprojects/libvhost-user/.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230202133830.2152150-4-armbru@redhat.com>
When running with --check-dup-head, the script always claims it "Found
duplicate header file includes." Fix to do it only when it actually
found some.
Fixes: d66253e46a ("scripts/clean-includes: added duplicate #include check")
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230202133830.2152150-3-armbru@redhat.com>
When clean-includes claims to skip or ignore a file, only the part
that sanitizes use of qemu/osdep.h skips the file. The part that
looks for duplicate #include does not, and neither does committing to
Git.
The latter can get unrelated stuff included in the commit, but only if
you run clean-includes in a dirty tree, which is unwise. Messed up
when we added skipping in commit fd3e39a40c "scripts/clean-includes:
Enhance to handle header files".
The former can cause bogus reports for --check-dup-head. Added in
commit d66253e46a "scripts/clean-includes: added duplicate #include
check", duplicating the prior mistake.
Fix the script to fully skip files.
Fixes: fd3e39a40c ("scripts/clean-includes: Enhance to handle header files")
Fixes: d66253e46a ("scripts/clean-includes: added duplicate #include check")
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230202133830.2152150-2-armbru@redhat.com>
aspeed queue:
* various small cleanups and fixes
* new variant of the supermicrox11-bmc machine using an ast2500-a1 SoC
* at24c_eeprom extension to define eeprom contents with static arrays
* ast10x0 model and test improvements
* avocado update of images to use the latest
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmPiByEACgkQUaNDx8/7
# 7KF1nw/7BxVb8bxO5T00AnGDFNahDq3ItyisrbOkElDw18oN1eULrtZFH1UopjDE
# 3HKwR2nb4X7MfcLirVXXxwO1GgIxUkeCsVEY6hpg3TxDPRhPW2toNpNt/WCfFKgq
# ZdYdaKgkON/xHQPv6kgQzU2n9Zpuznj0CE9A3k1mAyBcCSitsvu4TW6AQBKmLgUR
# 9lu61onfX9XoPxZv3abuY3c3UyzevOc6BUT67dmr8naAhHLyBU+DWAW6Kg0Dtc9j
# p+bwxIDRimK50DJt9l13OLSAJyhrW1gMsPPGb+48OClpEOhHwq8oqRuMFpbHaQ0/
# 2MMtMbavXtzBScfmLzR3yw2IwohxSXKMe+7irkJiG/hc8/gtpRATaaS+zfvS0rla
# QybWYtJyjmW+QUOnmBsKGwT0PWJcOd3bKtVPgPd7WGeHGVtTBOqU/svExaO+gIv8
# uX1gOelEgLmLenUjc/Wp4cHgnePTBK8vG1g3IrEtcCblhwpr0e3/aJgHGgO3cQzH
# X9P2buwHyLzjsie9S1ebG9Ceg/VsGQpxNGISZdG+Z4c3+GYu5gcGQcqIAuFmwBnE
# QHSNHJXITyWjo7UuqL7e1J7vROUKn0S15V9MO/yOmZgkqubu4Gt3jGcJtIGqIBlu
# MFra7SiVjKBnt6PD3aKEdD9uahbqFUfmX9411ZmYUUzpfflKnCQ=
# =IY/i
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Feb 2023 08:09:05 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230207' of https://github.com/legoater/qemu: (25 commits)
aspeed/sdmc: Drop unnecessary scu include
tests/avocado: Test Aspeed Zephyr SDK v00.01.08 on AST1030 board
hw/arm/aspeed_ast10x0: Add TODO comment to use Cortex-M4F
hw/arm/aspeed_ast10x0: Map HACE peripheral
hw/arm/aspeed_ast10x0: Map the secure SRAM
hw/arm/aspeed_ast10x0: Map I3C peripheral
hw/arm/aspeed_ast10x0: Add various unimplemented peripherals
hw/misc/aspeed_hace: Do not crash if address_space_map() failed
hw/watchdog/wdt_aspeed: Log unimplemented registers as UNIMP level
hw/watchdog/wdt_aspeed: Extend MMIO range to cover more registers
hw/watchdog/wdt_aspeed: Rename MMIO region size as 'iosize'
hw/nvram/eeprom_at24c: Make reset behavior more like hardware
hw/arm/aspeed: Add aspeed_eeprom.c
hw/nvram/eeprom_at24c: Add init_rom field and at24c_eeprom_init_rom helper
hw/arm/aspeed: Replace aspeed_eeprom_init with at24c_eeprom_init
hw/arm: Extract at24c_eeprom_init helper from Aspeed and Nuvoton boards
hw/core/loader: Remove declarations of option_rom_has_mr/rom_file_has_mr
tests/avocado/machine_aspeed.py: Mask systemd services to speed up SDK boot
tests/avocado/machine_aspeed.py: update buildroot tests
m25p80: Add the is25wp256 SFPD table
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Migration Pull request
In this try
- rebase to latest upstream
- same than previous patch
- fix compilation on non linux (userfaultfd.h) (me)
- query-migrationthreads (jiang)
- fix race on reading MultiFDPages_t.block (zhenzhong)
- fix flush of zero copy page send reuest (zhenzhong)
Please apply.
Previous try:
It includes:
- David Hildenbrand fixes for virtio-men
- David Gilbert canary to detect problems
- Fix for rdma return values (Fiona)
- Peter Xu uffd_open fixes
- Peter Xu show right downtime for postcopy
- manish.mishra msg fix fixes
- my vfio changes.
Please apply.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmPhobYACgkQ9IfvGFhy
# 1yMNaA/9EHDPqrI1HL/VkJG4nNOOsQR7RbburXEberZOzvLjnqpjUD3Ls9qV6rx+
# ieHa5T4imYJFk72Wa5vx4r1/dCjtJD2W6jg5+/0nTvYAHrs1U1VRqpuTr0HiXdbJ
# ZLLCnW5eDyO3eMaOX0MUkgHgL0FNkc/Lq5ViCTFsMu9O9xMuDLLdAC3cdvslKuOu
# X1gKByr9jT817Y9e36amYmRaJKC6Cr/PIekNVFu12HBW79pPusLX8KWEf4RBw4HR
# sPwTvMCR/BwZ0+2Lppan60G5rt/ZxDu40oU7y+RHlfWqevl4hDM84/nhjMvEgzc5
# a4Ahe2ERGLwwnC8z3l7v9+pEzSGzDoPcnRGvZcpUpk68wTDtxd5Bdq8CwmNUfL07
# VzWcYpH0yvmwjBba9jfn9fAVgnG5rVp558XcYLIII3wEToty3UDtm43wSdj2CGr6
# cu+IPAp+n/I5G9SRYBTU9ozJz45ttnEe0hxUtZ4I3MuhzHi1VEDAqTWM/X0LyS41
# TB3Y5B2KKpJYbPyZEH4nyTeetR2k7alTFzahCgKqVfOgL0nJx54petjS1K+B1P72
# g6lhP9WnQ33W+M8S7J/aGEaDJd1lFyFB2Rdjn2ZZnASH/fR9j0mFmXWvulXtjFNp
# Sfim3887+Iv4Uzw4VWEe3mM5Ypi/Ba2CmuTjy/pM08Ey8X1Qs5o=
# =ZQbR
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Feb 2023 00:56:22 GMT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20230206-pull-request' of https://gitlab.com/juan.quintela/qemu: (30 commits)
migration: save/delete migration thread info
migration: Introduce interface query-migrationthreads
multifd: Fix flush of zero copy page send request
multifd: Fix a race on reading MultiFDPages_t.block
migration: check magic value for deciding the mapping of channels
io: Add support for MSG_PEEK for socket channel
migration/dirtyrate: Show sample pages only in page-sampling mode
migration: Perform vmsd structure check during tests
migration: Add canary to VMSTATE_END_OF_LIST
migration/rdma: fix return value for qio_channel_rdma_{readv,writev}
migration: Show downtime during postcopy phase
virtio-mem: Proper support for preallocation with migration
virtio-mem: Migrate immutable properties early
virtio-mem: Fail if a memory backend with "prealloc=on" is specified
migration/ram: Factor out check for advised postcopy
migration/vmstate: Introduce VMSTATE_WITH_TMP_TEST() and VMSTATE_BITMAP_TEST()
migration/savevm: Allow immutable device state to be migrated early (i.e., before RAM)
migration/savevm: Prepare vmdesc json writer in qemu_savevm_state_setup()
migration/savevm: Move more savevm handling into vmstate_save()
migration/ram: Optimize ram_write_tracking_start() for RamDiscardManager
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This SoC uses a Cortex-M4F. QEMU only implements a M4,
which is good enough. Add a TODO note in case the M4F
is added.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Some SRAM appears to be used by the Secure Boot unit and
crypto accelerators. Name it 'secure sram'.
Note, the SRAM base address was already present but unused
(the 'SBC' index is used for the MMIO peripheral).
Interestingly using CFLAGS=-Winitializer-overrides reports:
../hw/arm/aspeed_ast10x0.c:32:30: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides]
[ASPEED_DEV_SBC] = 0x7E6F2000,
^~~~~~~~~~
../hw/arm/aspeed_ast10x0.c:24:30: note: previous initialization is here
[ASPEED_DEV_SBC] = 0x79000000,
^~~~~~~~~~
This fixes with Zephyr:
uart:~$ rsa test
rsa test vector[0]:
[00:00:26.156,000] <err> os: ***** BUS FAULT *****
[00:00:26.157,000] <err> os: Precise data bus error
[00:00:26.157,000] <err> os: BFAR Address: 0x79000000
[00:00:26.158,000] <err> os: r0/a1: 0x79000000 r1/a2: 0x00000000 r2/a3: 0x00001800
[00:00:26.158,000] <err> os: r3/a4: 0x79001800 r12/ip: 0x00000800 r14/lr: 0x0001098d
[00:00:26.158,000] <err> os: xpsr: 0x81000000
[00:00:26.158,000] <err> os: Faulting instruction address (r15/pc): 0x0001e1bc
[00:00:26.158,000] <err> os: >>> ZEPHYR FATAL ERROR 0: CPU exception on CPU 0
[00:00:26.158,000] <err> os: Current thread: 0x38248 (shell_uart)
[00:00:26.165,000] <err> os: Halting system
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
[ clg: Fixed size of Secure Boot Controller Memory ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Avoid confusing two different things:
- the WDT I/O region size ('iosize')
- at which offset the SoC map the WDT ('offset')
While it is often the same, we can map smaller region sizes
at larger offsets.
Here we are interested in the I/O region size, so rename as
'iosize'.
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[ clg: Introduced temporary wdt_offset variable ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
EEPROM's are a form of non-volatile memory. After power-cycling an EEPROM,
I would expect the I2C state machine to be reset to default values, but I
wouldn't really expect the memory to change at all.
The current implementation of the at24c EEPROM resets its internal memory on
reset. This matches the specification in docs/devel/reset.rst:
Cold reset is supported by every resettable object. In QEMU, it means we reset
to the initial state corresponding to the start of QEMU; this might differ
from what is a real hardware cold reset. It differs from other resets (like
warm or bus resets) which may keep certain parts untouched.
But differs from my intuition. For example, if someone writes some information
to an EEPROM, then AC power cycles their board, they would expect the EEPROM to
retain that information. It's very useful to be able to test things like this
in QEMU as well, to verify software instrumentation like determining the cause
of a reboot.
Fixes: 5d8424dbd3 ("nvram: add AT24Cx i2c eeprom")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20230128060543.95582-6-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
- Create aspeed_eeprom.c and aspeed_eeprom.h
- Include aspeed_eeprom.c in CONFIG_ASPEED meson source files
- Include aspeed_eeprom.h in aspeed.c
- Add fby35_bmc_fruid data
- Use new at24c_eeprom_init_rom helper to initialize BMC FRUID EEPROM with data
from aspeed_eeprom.c
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
qemu-system-aarch64 -machine fby35-bmc -nographic -mtdblock fby35.mtd
...
user: root
pass: 0penBmc
...
root@bmc-oob:~# fruid-util bb
FRU Information : Baseboard
--------------- : ------------------
Chassis Type : Rack Mount Chassis
Chassis Part Number : N/A
Chassis Serial Number : N/A
Board Mfg Date : Fri Jan 7 10:30:00 2022
Board Mfg : XXXXXX
Board Product : Management Board wBMC
Board Serial : XXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXX
Board FRU ID : 1.0
Board Custom Data 1 : XXXXXXXXX
Board Custom Data 2 : XXXXXXXXXXXXXXXXXX
Product Manufacturer : XXXXXX
Product Name : Yosemite V3.5 EVT2
Product Part Number : XXXXXXXXXXXXXX
Product Version : EVT2
Product Serial : XXXXXXXXXXXXX
Product Asset Tag : XXXXXXX
Product FRU ID : 1.0
Product Custom Data 1 : XXXXXXXXX
Product Custom Data 2 : N/A
root@bmc-oob:~# fruid-util bmc
FRU Information : BMC
--------------- : ------------------
Board Mfg Date : Mon Jan 10 21:42:00 2022
Board Mfg : XXXXXX
Board Product : BMC Storage Module
Board Serial : XXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXX
Board FRU ID : 1.0
Board Custom Data 1 : XXXXXXXXX
Board Custom Data 2 : XXXXXXXXXXXXXXXXXX
Product Manufacturer : XXXXXX
Product Name : Yosemite V3.5 EVT2
Product Part Number : XXXXXXXXXXXXXX
Product Version : EVT2
Product Serial : XXXXXXXXXXXXX
Product Asset Tag : XXXXXXX
Product FRU ID : 1.0
Product Custom Data 1 : XXXXXXXXX
Product Custom Data 2 : Config A
root@bmc-oob:~# fruid-util nic
FRU Information : NIC
--------------- : ------------------
Board Mfg Date : Tue Nov 2 08:51:00 2021
Board Mfg : XXXXXXXX
Board Product : Mellanox ConnectX-6 DX OCP3.0
Board Serial : XXXXXXXXXXXXXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXXXXXXXXX
Board FRU ID : FRU Ver 0.02
Product Manufacturer : XXXXXXXX
Product Name : Mellanox ConnectX-6 DX OCP3.0
Product Part Number : XXXXXXXXXXXXXXXXXXXXX
Product Version : A9
Product Serial : XXXXXXXXXXXXXXXXXXXXXXXX
Product Custom Data 3 : ConnectX-6 DX
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20230128060543.95582-5-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allows users to specify binary data to initialize an EEPROM, allowing users to
emulate data programmed at manufacturing time.
- Added init_rom and init_rom_size attributes to TYPE_AT24C_EE
- Added at24c_eeprom_init_rom helper function to initialize attributes
- If -drive property is provided, it overrides init_rom data
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Ninad Palsule <ninadpalsule@us.ibm.com>
Link: https://lore.kernel.org/r/20230128060543.95582-4-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Use buildroot 2022.11 based images plus some customization :
- Linux version is bumped to 6.0.9 and kernel is built with a custom
config similar to what OpenBMC provides.
- U-Boot is switched to the one provided by OpenBMC for better support.
- defconfigs includes more target tools for dev.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20230119123449.531826-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Update the test_arm_ast2600_debian test to
- the latest Debian kernel
- use the Rainier machine instead of Tacoma
Both of which contains support for more hardware and thus exercises more
of the hardware Qemu models.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220607011938.1676459-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
With the `size += 4` before the call to `crc32`, the CRC calculation
would overrun the buffer. Size is used in the while loop starting on
line 1009 to determine how much data to write back, with the last
four bytes coming from `crc_ptr`, so do need to increase it, but should
do this after the computation.
I'm unsure why this use of uninitialized memory in the CRC doesn't
result in CRC errors, but it seems clear to me that it should not be
included in the calculation.
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20221220221437.3303721-1-slongfield@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
supermicrox11-bmc is configured with ast2400-a1 SoC. This does not match
the Supermicro documentation for X11 BMCs, and it does not match the
devicetree file in the Linux kernel.
As it turns out, some Supermicro X11 motherboards use AST2400 SoCs,
while others use AST2500.
Introduce new machine type supermicrox11-spi-bmc with AST2500 SoC
to match the devicetree description in the Linux kernel. Hardware
configuration details for this machine type are guesswork and taken
from defaults as well as from the Linux kernel devicetree file.
The new machine type was tested with aspeed-bmc-supermicro-x11spi.dts
from the Linux kernel and with Linux versions 6.0.3 and 6.1-rc2.
Linux booted successfully from initrd and from both SPI interfaces.
Ethernet interfaces were confirmed to be operational.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/r/20221025165109.1226001-1-linux@roeck-us.net
[ clg: Renamed machine to 'supermicro-x11spi-bmc' ]
Message-Id: <20221025165109.1226001-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The M2S-FG484 SOM uses a 16 MiB SPI flash (Spansion
S25FL128SDPBHICO). Since the test asset is bigger,
truncate it to the correct size to avoid when running
the test_arm_emcraft_sf2 test:
qemu-system-arm: device requires 16777216 bytes, block backend provides 67108864 bytes
Add comment regarding the M2S-FG484 SOM hardware in
hw/arm/msf2-som.c.
Reported-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
commit fb3f3730e4 added mechanism to generate virtual instruction
exception during instruction decode when virt is enabled.
However in some situations, illegal instruction exception can be raised
due to state of CPU. One such situation is implementing branch tracking.
[1] An indirect branch if doesn't land on a landing pad instruction, then
cpu must raise an illegal instruction exception.
Implementation would raise such expcetion due to missing landing pad inst
and not due to decode. Thus DisasContext must have `virt_inst_excp`
initialized to false during DisasContxt initialization for TB.
[1] - https://github.com/riscv/riscv-cfi
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230127191758.755844-1-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadCmo ISA extension.
To avoid interfering with standard extensions, decoder and translation
are in its own xthead* specific files.
Future patches should be able to easily add additional T-Head extension.
The implementation does not have much functionality (besides accepting
the instructions and not qualifying them as illegal instructions if
the hart executes in the required privilege level for the instruction),
as QEMU does not model CPU caches and instructions are documented
to not raise any exceptions.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230131202013.2541053-2-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As it is now, riscv_compute_fdt_addr() is receiving a dram_base, a
mem_size (which is defaulted to MachineState::ram_size in all boards)
and the FDT pointer. And it makes a very important assumption: the DRAM
interval dram_base + mem_size is contiguous. This is indeed the case for
most boards that use a FDT.
The Icicle Kit board works with 2 distinct RAM banks that are separated
by a gap. We have a lower bank with 1GiB size, a gap follows, then at
64GiB the high memory starts. MachineClass::default_ram_size for this
board is set to 1.5Gb, and machine_init() is enforcing it as minimal RAM
size, meaning that there we'll always have at least 512 MiB in the Hi
RAM area.
Using riscv_compute_fdt_addr() in this board is weird because not only
the board has sparse RAM, and it's calling it using the base address of
the Lo RAM area, but it's also using a mem_size that we have guarantees
that it will go up to the Hi RAM. All the function assumptions doesn't
work for this board.
In fact, what makes the function works at all in this case is a
coincidence. Commit 1a475d39ef introduced a 3GB boundary for the FDT,
down from 4Gb, that is enforced if dram_base is lower than 3072 MiB. For
the Icicle Kit board, memmap[MICROCHIP_PFSOC_DRAM_LO].base is 0x80000000
(2 Gb) and it has a 1Gb size, so it will fall in the conditions to put
the FDT under a 3Gb address, which happens to be exactly at the end of
DRAM_LO. If the base address of the Lo area started later than 3Gb this
function would be unusable by the board. Changing any assumptions inside
riscv_compute_fdt_addr() can also break it by accident as well.
Let's change riscv_compute_fdt_addr() semantics to be appropriate to the
Icicle Kit board and for future boards that might have sparse RAM
topologies to worry about:
- relieve the condition that the dram_base + mem_size area is contiguous,
since this is already not the case today;
- receive an extra 'dram_size' size attribute that refers to a contiguous
RAM block that the board wants the FDT to reside on.
Together with 'mem_size' and 'fdt', which are now now being consumed by a
MachineState pointer, we're able to make clear assumptions based on the
DRAM block and total mem_size available to ensure that the FDT will be put
in a valid RAM address.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230201171212.1219375-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A common trend in other archs is to calculate the fdt address, which is
usually straightforward, and then calling a function that loads the
fdt/dtb by using that address.
riscv_load_fdt() is doing a bit too much in comparison. It's calculating
the fdt address via an elaborated heuristic to put the FDT at the bottom
of DRAM, and "bottom of DRAM" will vary across boards and
configurations, then it's actually loading the fdt, and finally it's
returning the fdt address used to the caller.
Reduce the existing complexity of riscv_load_fdt() by splitting its code
into a new function, riscv_compute_fdt_addr(), that will take care of
all fdt address logic. riscv_load_fdt() can then be a simple function
that just loads a fdt at the given fdt address.
We're also taken the opportunity to clarify the intentions and
assumptions made by these functions. riscv_load_fdt() is now receiving a
hwaddr as fdt_addr because there is no restriction of having to load the
fdt in higher addresses that doesn't fit in an uint32_t.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230201171212.1219375-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We have a convention in other QEMU boards/archs to name MachineState
pointers as either 'machine' or 'ms'. MachineClass pointers are usually
called 'mc'.
The 'virt' RISC-V machine has a lot of instances where MachineState
pointers are named 'mc'. There is nothing wrong with that, but we gain
more compatibility with the rest of the QEMU code base, and easier
reviews, if we follow QEMU conventions.
Rename all 'mc' MachineState pointers to 'ms'. This is a very tedious
and mechanical patch that was produced by doing the following:
- find/replace all 'MachineState *mc' to 'MachineState *ms';
- find/replace all 'mc->fdt' to 'ms->fdt';
- find/replace all 'mc->smp.cpus' to 'ms->smp.cpus';
- replace any remaining occurrences of 'mc' that the compiler complained
about.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230124212234.412630-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
riscv_socket_count() returns either ms->numa_state->num_nodes or 1
depending on NUMA support. In any case the value can be retrieved only
once and used in the rest of the function.
This will also alleviate the rename we're going to do next by reducing
the instances of MachineState 'mc' inside hw/riscv/virt.c.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230124212234.412630-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We should call decode_save_opc() for all relevant instructions which
can potentially generate a virtual instruction fault or a guest page
fault because generating transformed instruction upon guest page fault
expects opcode to be available. Without this, hypervisor will see
transformed instruction as zero in htinst CSR for guest MMIO emulation
which makes MMIO emulation in hypervisor slow and also breaks nested
virtualization.
Fixes: a9814e3e08 ("target/riscv: Minimize the calls to decode_save_opc")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230120125950.2246378-5-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The decoding of the following instructions from Zb[abcs] currently
contains decoding/printing errors:
* xnor,orn,andn: the rs2 operand is not being printed
* slli.uw: decodes and prints the immediate shift-amount as a
register (e.g. 'shift-by-2' becomes 'sp') instead of
interpreting this as an immediate
This commit updates the instruction descriptions to use the
appropriate decoding/printing formats.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230120151551.1022761-1-philipp.tomsich@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To support query migration thread infomation, save and delete
thread(live_migration and multifdsend) information at thread
creation and finish.
Signed-off-by: Jiang Jiacheng <jiangjiacheng@huawei.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce interface query-migrationthreads. The interface is used
to query information about migration threads and returns with
migration thread's name and its id.
Introduce threadinfo.c to manage threads with migration.
Signed-off-by: Jiang Jiacheng <jiangjiacheng@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Make IO channel flush call after the inflight request has been drained
in multifd thread, or else we may missed to flush the inflight request.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In multifd_queue_page() MultiFDPages_t.block is checked twice.
Between the two checks, MultiFDPages_t.block may be reset to NULL
by multifd thread. This lead to the 2nd check always true then a
redundant page submitted to multifd thread again.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Current logic assumes that channel connections on the destination side are
always established in the same order as the source and the first one will
always be the main channel followed by the multifid or post-copy
preemption channel. This may not be always true, as even if a channel has a
connection established on the source side it can be in the pending state on
the destination side and a newer connection can be established first.
Basically causing out of order mapping of channels on the destination side.
Currently, all channels except post-copy preempt send a magic number, this
patch uses that magic number to decide the type of channel. This logic is
applicable only for precopy(multifd) live migration, as mentioned, the
post-copy preempt channel does not send any magic number. Also, tls live
migrations already does tls handshake before creating other channels, so
this issue is not possible with tls, hence this logic is avoided for tls
live migrations. This patch uses read peek to check the magic number of
channels so that current data/control stream management remains
un-effected.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: manish.mishra <manish.mishra@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
MSG_PEEK peeks at the channel, The data is treated as unread and
the next read shall still return this data. This support is
currently added only for socket class. Extra parameter 'flags'
is added to io_readv calls to pass extra read flags like MSG_PEEK.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: manish.mishra <manish.mishra@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The value of "Sample Pages" is confusing in mode other than page-sampling.
See below:
(qemu) calc_dirty_rate -b 10 520
(qemu) info dirty_rate
Status: measuring
Start Time: 11646834 (ms)
Sample Pages: 520 (per GB)
Period: 10 (sec)
Mode: dirty-bitmap
Dirty rate: (not ready)
(qemu) info dirty_rate
Status: measured
Start Time: 11646834 (ms)
Sample Pages: 0 (per GB)
Period: 10 (sec)
Mode: dirty-bitmap
Dirty rate: 2 (MB/s)
While it's totally useless in dirty-ring and dirty-bitmap mode, fix to
show it only in page-sampling mode.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Perform a check on vmsd structures during test runs in the hope
of catching any missing terminators and other simple screwups.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We fairly regularly forget VMSTATE_END_OF_LIST markers off descriptions;
given that the current check is only for ->name being NULL, sometimes
we get unlucky and the code apparently works and no one spots the error.
Explicitly add a flag, VMS_END that should be set, and assert it is
set during the traversal.
Note: This can't go in until we update the copy of vmstate.h in slirp.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
upon errors. As the documentation in include/io/channel.h states, only
-1 and QIO_CHANNEL_ERR_BLOCK should be returned upon error. Other
values have the potential to confuse the call sites.
error_setg is used rather than error_setg_errno, because there are
certain code paths where -1 (as a non-errno) is propagated up (e.g.
starting from qemu_rdma_block_for_wrid or qemu_rdma_post_recv_control)
all the way to qio_channel_rdma_{readv,writev}.
Similar to a216ec85b7 ("migration/channel-block: fix return value for
qio_channel_block_{readv,writev}").
Suggested-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The downtime should be displayed during postcopy phase because the
switchover phase is done. OTOH it's weird to show "expected downtime"
which can confuse what does that mean if the switchover has already
happened anyway.
This is a slight ABI change on QMP, but I assume it shouldn't affect
anyone.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Ordinary memory preallocation runs when QEMU starts up and creates the
memory backends, before processing the incoming migration stream. With
virtio-mem, we don't know which memory blocks to preallocate before
migration started. Now that we migrate the virtio-mem bitmap early, before
migrating any RAM content, we can safely preallocate memory for all plugged
memory blocks before migrating any RAM content.
This is especially relevant for the following cases:
(1) User errors
With hugetlb/files, if we don't have sufficient backend memory available on
the migration destination, we'll crash QEMU (SIGBUS) during RAM migration
when running out of backend memory. Preallocating memory before actual
RAM migration allows for failing gracefully and informing the user about
the setup problem.
(2) Excluded memory ranges during migration
For example, virtio-balloon free page hinting will exclude some pages
from getting migrated. In that case, we won't crash during RAM
migration, but later, when running the VM on the destination, which is
bad.
To fix this for new QEMU machines that migrate the bitmap early,
preallocate the memory early, before any RAM migration. Warn with old
QEMU machines.
Getting postcopy right is a bit tricky, but we essentially now implement
the same (problematic) preallocation logic as ordinary preallocation:
preallocate memory early and discard it again before precopy starts. During
ordinary preallocation, discarding of RAM happens when postcopy is advised.
As the state (bitmap) is loaded after postcopy was advised but before
postcopy starts listening, we have to discard memory we preallocated
immediately again ourselves.
Note that nothing (not even hugetlb reservations) guarantees for postcopy
that backend memory (especially, hugetlb pages) are still free after they
were freed ones while discarding RAM. Still, allocating that memory at
least once helps catching some basic setup problems.
Before this change, trying to restore a VM when insufficient hugetlb
pages are around results in the process crashing to to a "Bus error"
(SIGBUS). With this change, QEMU fails gracefully:
qemu-system-x86_64: qemu_prealloc_mem: preallocating memory failed: Bad address
qemu-system-x86_64: error while loading state for instance 0x0 of device '0000:00:03.0/virtio-mem-device-early'
qemu-system-x86_64: load of migration failed: Cannot allocate memory
And we can even introspect the early migration data, including the
bitmap:
$ ./scripts/analyze-migration.py -f STATEFILE
{
"ram (2)": {
"section sizes": {
"0000:00:03.0/mem0": "0x0000000780000000",
"0000:00:04.0/mem1": "0x0000000780000000",
"pc.ram": "0x0000000100000000",
"/rom@etc/acpi/tables": "0x0000000000020000",
"pc.bios": "0x0000000000040000",
"0000:00:02.0/e1000.rom": "0x0000000000040000",
"pc.rom": "0x0000000000020000",
"/rom@etc/table-loader": "0x0000000000001000",
"/rom@etc/acpi/rsdp": "0x0000000000001000"
}
},
"0000:00:03.0/virtio-mem-device-early (51)": {
"tmp": "00 00 00 01 40 00 00 00 00 00 00 07 80 00 00 00 00 00 00 00 00 20 00 00 00 00 00 00",
"size": "0x0000000040000000",
"bitmap": "ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [...]
},
"0000:00:04.0/virtio-mem-device-early (53)": {
"tmp": "00 00 00 08 c0 00 00 00 00 00 00 07 80 00 00 00 00 00 00 00 00 20 00 00 00 00 00 00",
"size": "0x00000001fa400000",
"bitmap": "ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [...]
},
[...]
Reported-by: Jing Qi <jinqi@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The bitmap and the size are immutable while migration is active: see
virtio_mem_is_busy(). We can migrate this information early, before
migrating any actual RAM content. Further, all information we need for
sanity checks is immutable as well.
Having this information in place early will, for example, allow for
properly preallocating memory before touching these memory locations
during RAM migration: this way, we can make sure that all memory was
actually preallocated and that any user errors (e.g., insufficient
hugetlb pages) can be handled gracefully.
In contrast, usable_region_size and requested_size can theoretically
still be modified on the source while the VM is running. Keep migrating
these properties the usual, late, way.
Use a new device property to keep behavior of compat machines
unmodified.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
"prealloc=on" for the memory backend does not work as expected, as
virtio-mem will simply discard all preallocated memory immediately again.
In the best case, it's an expensive NOP. In the worst case, it's an
unexpected allocation error.
Instead, "prealloc=on" should be specified for the virtio-mem device only,
such that virtio-mem will try preallocating memory before plugging
memory dynamically to the guest. Fail if such a memory backend is
provided.
Tested-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let's factor out this check, to be used in virtio-mem context next.
While at it, fix a spelling error in a related comment.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
For virtio-mem, we want to have the plugged/unplugged state of memory
blocks available before migrating any actual RAM content, and perform
sanity checks before touching anything on the destination. This
information is immutable on the migration source while migration is active,
We want to use this information for proper preallocation support with
migration: currently, we don't preallocate memory on the migration target,
and especially with hugetlb, we can easily run out of hugetlb pages during
RAM migration and will crash (SIGBUS) instead of catching this gracefully
via preallocation.
Migrating device state via a VMSD before we start iterating is currently
impossible: the only approach that would be possible is avoiding a VMSD
and migrating state manually during save_setup(), to be restored during
load_state().
Let's allow for migrating device state via a VMSD early, during the
setup phase in qemu_savevm_state_setup(). To keep it simple, we
indicate applicable VMSD's using an "early_setup" flag.
Note that only very selected devices (i.e., ones seriously messing with
RAM setup) are supposed to make use of such early state migration.
While at it, also use a bool for the "unmigratable" member.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
... and store it in the migration state. This is a preparation for
storing selected vmds's already in qemu_savevm_state_setup().
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let's move more code into vmstate_save(), reducing code duplication and
preparing for reuse of vmstate_save() in qemu_savevm_state_setup(). We
have to move vmstate_save() to make the compiler happy.
We'll now also trace from qemu_save_device_state(), triggering the same
tracepoints as previously called from
qemu_savevm_state_complete_precopy_non_iterable() only. Note that
qemu_save_device_state() ignores iterable device state, such as RAM,
and consequently doesn't trigger some other trace points (e.g.,
trace_savevm_state_setup()).
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
ram_block_populate_read() already optimizes for RamDiscardManager.
However, ram_write_tracking_start() will still try protecting discarded
memory ranges.
Let's optimize, because discarded ranges don't map any pages and
(1) For anonymous memory, trying to protect using uffd-wp without a mapped
page is ignored by the kernel and consequently a NOP.
(2) For shared/file-backed memory, we will fill present page tables in the
range with PTE markers. However, we will even allocate page tables
just to fill them with unnecessary PTE markers and effectively
waste memory.
So let's exclude these ranges, just like ram_block_populate_read()
already does.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
ram_mig_ram_block_resized() will abort migration (including background
snapshots) when resizing a RAMBlock. ram_block_populate_read() will only
populate RAM up to used_length, so at least for anonymous memory
protecting everything between used_length and max_length won't
actually be protected and is just a NOP.
So let's only protect everything up to used_length.
Note: it still makes sense to register uffd-wp for max_length, such
that RAM_UF_WRITEPROTECT is independent of a changing used_length.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When unregistering uffd-wp, older kernels before commit f369b07c86143
("mm/uffd:reset write protection when unregister with wp-mode") won't
clear the uffd-wp PTE bit. When re-registering uffd-wp, the previous
uffd-wp PTE bits would trigger again. With above commit, the kernel will
clear the uffd-wp PTE bits when unregistering itself.
Consequently, we'll clear the uffd-wp PTE bits now twice -- whereby we
don't care about clearing them at all: a new background snapshot will
re-register uffd-wp and re-protect all memory either way.
So let's skip the manual clearing of uffd-wp. If ever relevant, we
could clear conditionally in uffd_unregister_memory() -- we just need a
way to figure out more recent kernels.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If something goes wrong during uffd_change_protection(), we would miss
to unregister uffd-wp and not release our reference. Fix it by
performing the uffd_change_protection(true) last.
Note that a uffd_change_protection(false) on the recovery path without a
prior uffd_change_protection(false) is fine.
Fixes: 278e2f551a ("migration: support UFFD write fault processing in ram_save_iterate()")
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Unfortunately, commit f7b9dcfbcf broke populate_read_range(): the loop
end condition is very wrong, resulting in that function not populating the
full range. Lets' fix that.
Fixes: f7b9dcfbcf ("migration/ram: Factor out populating pages readable in ram_block_populate_pages()")
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Until previous commit, save_live_pending() was used for ram. Now with
the split into state_pending_estimate() and state_pending_exact() it
is not needed anymore, so remove them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We split the function into to:
- state_pending_estimate: We estimate the remaining state size without
stopping the machine.
- state pending_exact: We calculate the exact amount of remaining
state.
The only "device" that implements different functions for _estimate()
and _exact() is ram.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit d9e474ea56 overlooked the case where the target psize is even larger
than the host psize. One example is Alpha has 8K page size and migration
will start to crash the source QEMU when running Alpha migration on x86.
Fix it by detecting that case and set host start/end just to cover the
single page to be migrated.
This will slightly optimize the common case where host psize equals to
guest psize so we don't even need to do the roundups, but that's trivial.
Cc: qemu-stable@nongnu.org
Reported-by: Thomas Huth <thuth@redhat.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1456
Fixes: d9e474ea56 ("migration: Teach PSS about host page")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
scripts/ci/org.centos/stream/8/build-environment.yml has a slightly different
list of packages compared to scripts/ci/setup/build-environment.yaml. Make
them the same.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the CI playbook so that it is able to prepare a system with a
fresh CentOS Stream 8 install, rather than just support RHEL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ppc patch queue for 2023-02-05:
This queue includes patches that aren't PPC specific but benefit/impact
PPC machines, such as the changes to guestperf.py, mv64361 and sm501. As
for PPC specific changes we have e500 and PNV_PHB5 fixes.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCY99+yRYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFkOQsA/1UxMHen/3tW908shrRMwS7WSzDa
# 4x0tU4L+bMpEfgVJAQDeKIyIbdajtv4v2XfZyQ9flfUo64cY0xze+T+SDW+fBw==
# =eB7g
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 05 Feb 2023 10:02:49 GMT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20230205' of https://gitlab.com/danielhb/qemu:
hw/display/sm501: Code style fix
hw/display/sm501: Remove unneeded casts from void pointer
hw/display/sm501: Remove parenthesis around constant macro definitions
hw/ppc/pegasos2: Fix a typo in a comment
ppc/pnv/pci: Fix PHB xscom registers memory region name
ppc/pnv/pci: Update PHB5 version register
ppc/pnv/pci: Remove duplicate definition of PNV_PHB5_DEVICE_ID
ppc/pnv/pci: Cleanup PnvPHBPecState structure
hw/ppc/e500.c: Attach eSDHC unimplemented region to ccsr_addr_space
hw/ppc/e500.c: Avoid hardcoding parent device in create_devtree_etsec()
hw/ppc/e500{, plat}: Drop redundant checks for presence of platform bus
hw/ppc: Set machine->fdt in e500 machines
hw/pci-host/mv64361: Reuse pci_swizzle_map_irq_fn
ppc/pegasos2: Improve readability of VIA south bridge creation
tests/migration: add support for ppc64le for guestperf.py
tests/migration: add sysprof-capture-4 as dependency for stress binary
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The name is for the region mapping the PHB xscom registers. It was
apparently a bad cut-and-paste from the per-stack pci xscom area just
above, so we had two regions with the same name.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230127122848.550083-5-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
PNV_PHB5_DEVICE_ID is defined in two different headers. The definition
in hw/pci-host/pnv_phb4.h was left out in a previous rework.
Remaining definition is in hw/pci-host/pnv_phb.h.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230127122848.550083-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Makes the unimplemented region move together with the CCSR address space
if moved by a bootloader. Moving the CCSR address space isn't
implemented yet but this patch is a preparation for it.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230125130024.158721-5-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Slightly improve readability of creating the south btidge by cnamging
type of a local variable to avoid some casts within function arguments
which makes some lines shorter and easier to read.
Also remove an unneded line break.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230117214545.5E191746369@zero.eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
`make tests/migration/stress` fails with:
FAILED: tests/migration/stress
cc -m64 -mlittle-endian -o tests/migration/stress tests/migration/stress.p/stress.c.o -Wl,--as-needed -Wl,--no-undefined -pie -Wl,--warn-common -Wl,-z,relro -Wl,-z,now -fstack-protector-strong -static -pthread -Wl,--start-group -lgthread-2.0 -lglib-2.0 -Wl,--end-group
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gutils.c.o): in function `.annobin_gutils.c':
(.text+0x3b4): warning: Using 'getpwuid' in statically linked applications requires at runtime the shared libraries from the glibc version used for linking
/usr/bin/ld: (.text+0x178): warning: Using 'getpwnam_r' in statically linked applications requires at runtime the shared libraries from the glibc version used for linking
/usr/bin/ld: (.text+0x1bc): warning: Using 'getpwuid_r' in statically linked applications requires at runtime the shared libraries from the glibc version used for linking
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gthread.c.o):(.toc+0x0): undefined reference to `sysprof_clock'
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gtrace.c.o): in function `.annobin_gtrace.c':
(.text+0x24): undefined reference to `sysprof_collector_mark_vprintf'
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gtrace.c.o): in function `g_trace_define_int64_counter':
(.text+0x8c): undefined reference to `sysprof_collector_request_counters'
/usr/bin/ld: (.text+0x108): undefined reference to `sysprof_collector_define_counters'
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gtrace.c.o): in function `g_trace_set_int64_counter':
(.text+0x23c): undefined reference to `sysprof_collector_set_counters'
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gspawn.c.o):(.toc+0x0): undefined reference to `sysprof_clock'
/usr/bin/ld: /usr/lib/gcc/ppc64le-redhat-linux/11/../../../../lib64/libglib-2.0.a(gmain.c.o):(.toc+0x0): undefined reference to `sysprof_clock'
collect2: error: ld returned 1 exit status
ninja: build stopped: subcommand failed.
make: *** [Makefile:162: run-ninja] Error 1
Add sysprof-capture-4 as dependency for stress binary.
Tested on:
- CentOS Stream 9 ppc64le
- Fedora 36 x86_64
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20220809002451.91541-2-muriloo@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
tcg: Add support for TCGv_i128 in parameters and returns.
tcg: Add support for TCGv_i128 in cmpxchg.
tcg: Test CPUJumpCache in tb_jmp_cache_clear_page
tcg: Split out tcg_gen_nonatomic_cmpxchg_i{32,64}
tcg/aarch64: Fix patching of LDR in tb_target_set_jmp_target
target/arm: Use tcg_gen_atomic_cmpxchg_i128
target/i386: Use tcg_gen_atomic_cmpxchg_i128
target/i386: Use tcg_gen_nonatomic_cmpxchg_i{32,64}
target/s390x: Use tcg_gen_atomic_cmpxchg_i128
target/s390x: Use TCGv_i128 in passing and returning float128
target/s390x: Implement CC_OP_NZ in gen_op_calc_cc
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmPeiDYdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+hFQf+K1MkEK1wtpjnqrYD
# 4l36Uo3B7w8Yi6FxbCx9NP78dJNNTjTn0zqhtISRKSzI7TGUCGnmQs40iqYrRe5S
# 9x6LJgTJplI2dsANvtsTaWB5gNzhowPt5tlit+J6Q0POwvvwcBZAOumY8AYt1YP+
# dMsjBLw6HFaqSCU5IERZrB4kBwl61VTkTAtHL2utSZpdsOYoc3y2hzbJ/w3kLK2u
# YXnMvom+Gc1rvQTaSMgiPYFITyx/VtXDe+JQwNikpu7Na+RFjtu7cHmg/BtZFo6s
# 15AsAS8JlENKAunpJiX41UR7SxB8MdyQL5LyjVNWo5F7+YgQuuO1gqYKt6qUwd+A
# oH2uBA==
# =xjMy
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 04 Feb 2023 16:30:46 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20230204' of https://gitlab.com/rth7680/qemu: (40 commits)
tcg/aarch64: Fix patching of LDR in tb_target_set_jmp_target
target/i386: Inline cmpxchg16b
target/i386: Inline cmpxchg8b
target/i386: Split out gen_cmpxchg8b, gen_cmpxchg16b
target/s390x: Implement CC_OP_NZ in gen_op_calc_cc
target/s390x: Use tcg_gen_atomic_cmpxchg_i128 for CDSG
target/s390x: Use Int128 for passing float128
target/s390x: Use Int128 for returning float128
target/s390x: Copy wout_x1 to wout_x1_P
target/s390x: Use Int128 for return from TRE
target/s390x: Use Int128 for return from CKSM
target/s390x: Use Int128 for return from CLST
target/s390x: Use a single return for helper_divs64/u64
target/s390x: Use a single return for helper_divs32/u32
tests/tcg/s390x: Add cdsg.c
tests/tcg/s390x: Add long-double.c
tests/tcg/s390x: Add clst.c
tests/tcg/s390x: Add div.c
target/ppc: Use tcg_gen_atomic_cmpxchg_i128 for STQCX
target/arm: Use tcg_gen_atomic_cmpxchg_i128 for CASP
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use tcg_gen_atomic_cmpxchg_i128 for the atomic case,
and tcg_gen_qemu_ld/st_i128 otherwise.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Make a copy of wout_x1 before modifying it, as wout_x1_P
emphasizing that it operates on the out/out2 pair. The insns
that use x1_P are data movement that will not change to Int128.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Pack the quotient and remainder into a single Int128.
Use the divu128 primitive to remove the cpu_abort on
32-bit hosts.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v2: Extended div test case to cover these insns.
Pack the quotient and remainder into a single uint64_t.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v2: Fix operand ordering; use tcg_extr32_i64.
Note that the previous direct reference to reserve_val,
- tcg_gen_ld_i64(t1, cpu_env, (ctx->le_mode
- ? offsetof(CPUPPCState, reserve_val2)
- : offsetof(CPUPPCState, reserve_val)));
was incorrect because all references should have gone through
cpu_reserve_val. Create a cpu_reserve_val2 tcg temp to fix this.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221112061122.2720163-2-richard.henderson@linaro.org>
Normally this is automatically handled by the CF_PARALLEL checks
with in tcg_gen_atomic_cmpxchg_i{32,64}, but x86 has a special
case of !PREFIX_LOCK where it always wants the non-atomic version.
Split these out so that x86 does not have to roll its own.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These are not yet considering atomicity of the 16-byte value;
this is a direct replacement for the current target code which
uses a pair of 8-byte operations.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add code generation functions for data movement between
TCGv_i128 (mov) and to/from TCGv_i64 (concat, extract).
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This enables allocation of i128. The type is not yet
usable, as we have not yet added data movement ops.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fill in the parameters for libffi for Int128.
Adjust the interpreter to allow for 16-byte return values.
Adjust tcg_out_call to record the return value length.
Call parameters are no longer all the same size, so we
cannot reuse the same call_slots array for every function.
Compute it each time now, but only fill in slots required
for the call we're about to make.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We expect the backend to require register pairs in
host-endian ordering, thus for big-endian the first
register of a pair contains the high part.
We were forcing R0 to contain the low part for calls.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fill in the parameters for the host ABI for Int128.
Adjust tcg_target_call_oarg_reg for _WIN64, and
tcg_out_call for i386 sysv. Allow TCG_TYPE_V128
stores without AVX enabled.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We are about to allow passing Int128 to/from tcg helper functions,
but libffi doesn't support __int128_t, so use the structure.
In order for atomic128.h to continue working, we must provide
a mechanism to frob between real __int128_t and the structure.
Provide a new union, Int128Alias, for this. We cannot modify
Int128 itself, as any changed alignment would also break libffi.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This will be used by _WIN64 to return i128. Not yet used,
because allocation is not yet enabled.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These will be used by some hosts, both 32 and 64-bit, to pass and
return i128. Not yet used, because allocation is not yet enabled.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When allocating a temp to the stack frame, consider the
base type and allocate all parts at once.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Many hosts pass and return 128-bit quantities like sequential
64-bit quantities. Treat this just like we currently break
down 64-bit quantities for a 32-bit host.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Begin staging in support for TCGv_i128 with Int128.
Define the type enumerator, the typedef, and the
helper-head.h macros.
This cannot yet be used, because you can't allocate
temporaries of this new type.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Correctly handle large types while lowering.
Fixes: fac87bd2a4 ("tcg: Add temp_subindex to TCGTemp")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
After commit 4e4fa6c12d ("accel/tcg: Complete cpu initialization
before registration"), it looks the CPUJumpCache pointer can be NULL.
This causes a SIGSEV when running debug-wp-migration kvm unit test.
At the first place it should be clarified why this TCG code is called
with KVM acceleration. This may hide another bug.
Fixes: 4e4fa6c12d ("accel/tcg: Complete cpu initialization before registration")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20230203171510.2867451-1-eric.auger@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use g_strsplit() for the actual splitting. Give external linkage, so
the next commit can move one of its users to another source file.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230124121946.1139465-15-armbru@redhat.com>
The next commit will move a caller of help_cmd() to a new file.
Including monitor/monitor-internal.h there just for help_cmd() feels
silly. Better to provide it in monitor/hmp.h suitably renamed.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230124121946.1139465-8-armbru@redhat.com>
monitor/misc.h has static add_completion_option(). It's useful
elsewhere in the monitor. Since it's not monitor-specific, move it to
util/readline.c renamed to readline_add_completion_of(), and put it to
use.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230124121946.1139465-7-armbru@redhat.com>
Applications do call sendmsg() without any IOV, e.g.:
sendmsg(4, {msg_name=NULL, msg_namelen=0, msg_iov=NULL, msg_iovlen=0,
msg_control=[{cmsg_len=36, cmsg_level=SOL_ALG, cmsg_type=0x2}],
msg_controllen=40, msg_flags=0}, MSG_MORE) = 0
sendmsg(4, {msg_name=NULL, msg_namelen=0, msg_iov=[{iov_base="The quick brown fox jumps over t"..., iov_len=183}],
msg_iovlen=1, msg_control=[{cmsg_len=20, cmsg_level=SOL_ALG, cmsg_type=0x3}],
msg_controllen=24, msg_flags=0}, 0) = 183
The function do_sendrecvmsg_locked() is used for sndmsg() and recvmsg()
and calls lock_iovec() to lock the IOV into memory. For the first
sendmsg() above it returns NULL and thus wrongly skips the call the host
sendmsg() syscall, which will break the calling application.
Fix this issue by:
- allowing sendmsg() even with empty IOV
- skip recvmsg() if IOV is NULL
- skip both if the return code of do_sendrecvmsg_locked() != 0, which
indicates some failure like EFAULT on the IOV
Tested with the debian "ell" package with hppa guest on x86_64 host.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20221212173416.90590-2-deller@gmx.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add suport to handle SOL_ALG packets via sendmsg() and recvmsg().
This allows emulated userspace to use encryption functionality.
Tested with the debian ell package with hppa guest on x86_64 host.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20221212173416.90590-1-deller@gmx.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Both parameters have a different value on the parisc platform, so first
translate the target value into a host value for usage in the native
madvise() syscall.
Those parameters are often used by security sensitive applications (e.g.
tor browser, boringssl, ...) which expect the call to return a proper
return code on failure, so return -EINVAL if qemu fails to forward the
syscall to the host OS.
While touching this code, enhance the comments about MADV_DONTNEED.
Tested with testcase of tor browser when running hppa-linux guest on
x86-64 host.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <Y5iwTaydU7i66K/i@p100>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The hppa architectures provides an own output for the emulated
/proc/cpuinfo file.
Some userspace applications count (even if that's not the recommended
way) the number of lines which start with "processor:" and assume that
this number then reflects the number of online CPUs. Since those 3
architectures don't provide any such line, applications may assume "0"
CPUs. One such issue can be seen in debian bug report:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1024653
Avoid such issues by adding a "processor:" line for each of the online
CPUs.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <Y9QvyRSq1I1k5/JW@p100>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add translation for the host error return code of:
getsockopt(19, SOL_SOCKET, SO_ERROR, [ECONNREFUSED], [4]) = 0
This fixes the testsuite of the cockpit debian package with a
hppa-linux guest on a x86-64 host.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <Y9QzNzXg0hrzHQeo@p100>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This makes target_flat.h behave like every other target_xxx.h header.
It also makes it actually work -- while the current header says adding
a header to the target subdir overrides the common one, it doesn't.
This is for two reasons:
* meson.build adds -Ilinux-user before -Ilinux-user/$arch
* the compiler search path for "target_flat.h" looks in the same dir
as the source file before searching -I paths.
This can be seen with the xtensa port -- the subdir settings aren't
used which breaks stack setup.
Move it to the generic/ subdir and add include stubs like every
other target_xxx.h header is handled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230129004625.11228-1-vapier@gentoo.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
target-arm queue:
* Fix physical address resolution for Stage2
* pl011: refactoring, implement reset method
* Support GICv3 with hvf acceleration
* sbsa-ref: remove cortex-a76 from list of supported cpus
* Correct syndrome for ATS12NSO* traps at Secure EL1
* Fix priority of HSTR_EL2 traps vs UNDEFs
* Implement FEAT_FGT for '-cpu max'
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmPdGisZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3iTND/4qnI00PcqPhdZAD083admx
# Tn+7OaTd8aaWHDMvbnV3fNsvAEt//j8DdzeBGDLbgfhBuOCPB8z7oDSr7oqczmys
# Yjnh25o6IDUYtMnKR+dBwFKGvAqWwM4UdEllkHJvvM+QpnlH7iu9lCkgYr6PvBYA
# h4ajfZ5J7C2OmFJZqsKa2Ot3mveFxos1QzgWSmsWNGTJiZTOCiD7AvuCnEsBBaVP
# pESY+5eGjVmjv6ocHxcHG4LA456bHAf6JiCgKqgwowRBlJenpsnNgKleIN4gQA/J
# wtfLALNe6FkTV9tzK/MgtO1qOhxkUHrnTrYTtTLmk4H1VryFdDvomYB34zBIgfMY
# l1LmMba6UCoxtck13D5jv1xkE56o7Z3kqrhyOvP+aHFdi+dvYQ/z+b8pqUeYeSiu
# EbVWa/270JwVdbBT08vfW33Ci9n7fxZtRCrvj2viMgOiQOKwXYEb5AVxM9TRZSKC
# Y+1m5frW2HQ+KNvjEyHdMJ8q4nFhaS5Bq2A2RMaQCV2QBuBJvFkGL3ul6M0lw/eq
# cAZDKN6H/8N2l2DPcPHUy6RMiqUPSnemvFI814ElKeHGa1V1c7Iw9C4lWAV5Ue5E
# gotHC1ros89xV0Eg0gaB9UgX8TgbQUfc3g1g6YUvTCfQdvxL0H1rY+wUWU1h1V2r
# VdhxI95gUkgmoVnk8KnwIw==
# =hk0j
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 03 Feb 2023 14:28:59 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230203' of https://git.linaro.org/people/pmaydell/qemu-arm: (33 commits)
target/arm: Enable FEAT_FGT on '-cpu max'
target/arm: Implement MDCR_EL2.TDCC and MDCR_EL3.TDCC traps
target/arm: Implement the HFGITR_EL2.SVC_EL0 and SVC_EL1 traps
target/arm: Implement the HFGITR_EL2.ERET trap
target/arm: Mark up sysregs for HFGITR bits 48..63
target/arm: Mark up sysregs for HFGITR bits 18..47
target/arm: Mark up sysregs for HFGITR bits 12..17
target/arm: Mark up sysregs for HFGITR bits 0..11
target/arm: Mark up sysregs for HDFGRTR bits 12..63
target/arm: Mark up sysregs for HDFGRTR bits 0..11
target/arm: Mark up sysregs for HFGRTR bits 36..63
target/arm: Mark up sysregs for HFGRTR bits 24..35
target/arm: Mark up sysregs for HFGRTR bits 12..23
target/arm: Mark up sysregs for HFGRTR bits 0..11
target/arm: Implement FGT trapping infrastructure
target/arm: Define the FEAT_FGT registers
target/arm: Disable HSTR_EL2 traps if EL2 is not enabled
target/arm: Make HSTR_EL2 traps take priority over UNDEF-at-EL1
target/arm: All UNDEF-at-EL0 traps take priority over HSTR_EL2 traps
target/arm: Move do_coproc_insn() syndrome calculation earlier
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
FEAT_FGT also implements an extra trap bit in the MDCR_EL2 and
MDCR_EL3 registers: bit TDCC enables trapping of use of the Debug
Comms Channel registers OSDTRRX_EL1, OSDTRTX_EL1, MDCCSR_EL0,
MDCCINT_EL0, DBGDTR_EL0, DBGDTRRX_EL0 and DBGDTRTX_EL0 (and their
AArch32 equivalents). This trapping is independent of whether
fine-grained traps are enabled or not.
Implement these extra traps. (We don't implement DBGDTR_EL0,
DBGDTRRX_EL0 and DBGDTRTX_EL0.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-23-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-23-peter.maydell@linaro.org
Mark up the sysreg definitions for the registers trapped
by HFGRTR/HFGWTR bits 36..63.
Of these, some correspond to RAS registers which we implement as
always-UNDEF: these don't need any extra handling for FGT because the
UNDEF-to-EL1 always takes priority over any theoretical
FGT-trap-to-EL2.
Bit 50 (NACCDATA_EL1) is for the ACCDATA_EL1 register which is part
of the FEAT_LS64_ACCDATA feature which we don't yet implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-14-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-14-peter.maydell@linaro.org
Implement the machinery for fine-grained traps on normal sysregs.
Any sysreg with a fine-grained trap will set the new field to
indicate which FGT register bit it should trap on.
FGT traps only happen when an AArch64 EL2 enables them for
an AArch64 EL1. They therefore are only relevant for AArch32
cpregs when the cpreg can be accessed from EL0. The logic
in access_check_cp_reg() will check this, so it is safe to
add a .fgt marking to an ARM_CP_STATE_BOTH ARMCPRegInfo.
The DO_BIT and DO_REV_BIT macros define enum constants FGT_##bitname
which can be used to specify the FGT bit, eg
.fgt = FGT_AFSR0_EL1
(We assume that there is no bit name duplication across the FGT
registers, for brevity's sake.)
Subsequent commits will add the .fgt fields to the relevant register
definitions and define the FGT_nnn values for them.
Note that some of the FGT traps are for instructions that we don't
handle via the cpregs mechanisms (mostly these are instruction traps).
Those we will have to handle separately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-10-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-10-peter.maydell@linaro.org
Define the system registers which are provided by the
FEAT_FGT fine-grained trap architectural feature:
HFGRTR_EL2, HFGWTR_EL2, HDFGRTR_EL2, HDFGWTR_EL2, HFGITR_EL2
All these registers are a set of bit fields, where each bit is set
for a trap and clear to not trap on a particular system register
access. The R and W register pairs are for system registers,
allowing trapping to be done separately for reads and writes; the I
register is for system instructions where trapping is on instruction
execution.
The data storage in the CPU state struct is arranged as a set of
arrays rather than separate fields so that when we're looking up the
bits for a system register access we can just index into the array
rather than having to use a switch to select a named struct member.
The later FEAT_FGT2 will add extra elements to these arrays.
The field definitions for the new registers are in cpregs.h because
in practice the code that needs them is code that also needs
the cpregs information; cpu.h is included in a lot more files.
We're also going to add some FGT-specific definitions to cpregs.h
in the next commit.
We do not implement HAFGRTR_EL2, because we don't implement
FEAT_AMUv1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-9-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-9-peter.maydell@linaro.org
The HSTR_EL2 register is not supposed to have an effect unless EL2 is
enabled in the current security state. We weren't checking for this,
which meant that if the guest set up the HSTR_EL2 register we would
incorrectly trap even for accesses from Secure EL0 and EL1.
Add the missing checks. (Other places where we look at HSTR_EL2
for the not-in-v8A bits TTEE and TJDBX are already checking that
we are in NS EL0 or EL1, so there we alredy know EL2 is enabled.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-8-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-8-peter.maydell@linaro.org
The semantics of HSTR_EL2 require that it traps cpreg accesses
to EL2 for:
* EL1 accesses
* EL0 accesses, if the access is not UNDEFINED when the
trap bit is 0
(You can see this in the I_ZFGJP priority ordering, where HSTR_EL2
traps from EL1 to EL2 are priority 12, UNDEFs are priority 13, and
HSTR_EL2 traps from EL0 are priority 15.)
However, we don't get this right for EL1 accesses which UNDEF because
the register doesn't exist at all or because its ri->access bits
non-configurably forbid the access. At EL1, check for the HSTR_EL2
trap early, before either of these UNDEF reasons.
We have to retain the HSTR_EL2 check in access_check_cp_reg(),
because at EL0 any kind of UNDEF-to-EL1 (including "no such
register", "bad ri->access" and "ri->accessfn returns 'trap to EL1'")
takes precedence over the trap to EL2. But we only need to do that
check for EL0 now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230130182459.3309057-7-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-7-peter.maydell@linaro.org
The HSTR_EL2 register has a collection of trap bits which allow
trapping to EL2 for AArch32 EL0 or EL1 accesses to coprocessor
registers. The specification of these bits is that when the bit is
set we should trap
* EL1 accesses
* EL0 accesses, if the access is not UNDEFINED when the
trap bit is 0
In other words, all UNDEF traps from EL0 to EL1 take precedence over
the HSTR_EL2 trap to EL2. (Since this is all AArch32, the only kind
of trap-to-EL1 is the UNDEF.)
Our implementation doesn't quite get this right -- we check for traps
in the order:
* no such register
* ARMCPRegInfo::access bits
* HSTR_EL2 trap bits
* ARMCPRegInfo::accessfn
So UNDEFs that happen because of the access bits or because the
register doesn't exist at all correctly take priority over the
HSTR_EL2 trap, but where a register can UNDEF at EL0 because of the
accessfn we are incorrectly always taking the HSTR_EL2 trap. There
aren't many of these, but one example is the PMCR; if you look at the
access pseudocode for this register you can see that UNDEFs taken
because of the value of PMUSERENR.EN are checked before the HSTR_EL2
bit.
Rearrange helper_access_check_cp_reg() so that we always call the
accessfn, and use its return value if it indicates that the access
traps to EL0 rather than continuing to do the HSTR_EL2 check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-6-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-6-peter.maydell@linaro.org
Rearrange the code in do_coproc_insn() so that we calculate the
syndrome value for a potential trap early; we're about to add a
second check that wants this value earlier than where it is currently
determined.
(Specifically, a trap to EL2 because of HSTR_EL2 should take
priority over an UNDEF to EL1, even when the UNDEF is because
the register does not exist at all or because its ri->access
bits non-configurably fail the access. So the check we put in
for HSTR_EL2 trapping at EL1 (which needs the syndrome) is
going to have to be done before the check "is the ARMCPRegInfo
pointer NULL".)
This commit is just code motion; the change to HSTR_EL2
handling that will use the 'syndrome' variable is in a
subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-5-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-5-peter.maydell@linaro.org
We added the CPAccessResult values CP_ACCESS_TRAP_UNCATEGORIZED_EL2
and CP_ACCESS_TRAP_UNCATEGORIZED_EL3 purely in order to use them in
the ats_access() function, but doing so was incorrect (a bug fixed in
a previous commit). There aren't any cases where we want an access
function to be able to request a trap to EL2 or EL3 with a zero
syndrome value, so remove these enum values.
As well as cleaning up dead code, the motivation here is that
we'd like to implement fine-grained-trap handling in
helper_access_check_cp_reg(). Although the fine-grained traps
to EL2 are always lower priority than trap-to-same-EL and
higher priority than trap-to-EL3, they are in the middle of
various other kinds of trap-to-EL2. Knowing that a trap-to-EL2
must always for us have the same syndrome (ie that an access
function will return CP_ACCESS_TRAP_EL2 and there is no other
kind of trap-to-EL2 enum value) means we don't have to try
to choose which of the two syndrome values to report if the
access would trap to EL2 both for the fine-grained-trap and
because the access function requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-4-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-4-peter.maydell@linaro.org
The AArch32 ATS12NSO* address translation operations are supposed to
trap to either EL2 or EL3 if they're executed at Secure EL1 (which
can only happen if EL3 is AArch64). We implement this, but we got
the syndrome value wrong: like other traps to EL2 or EL3 on an
AArch32 cpreg access, they should report the 0x3 syndrome, not the
0x0 'uncategorized' syndrome. This is clear in the access pseudocode
for these instructions.
Fix the syndrome value for these operations by correcting the
returned value from the ats_access() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-3-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-3-peter.maydell@linaro.org
Let's explicitly list out all accelerators that we support when trying to
determine the supported set of GIC versions. KVM was already separate, so
the only missing one is HVF which simply reuses all of TCG's emulation
code and thus has the same compatibility matrix.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221223090107.98888-3-agraf@csgraf.de
[PMM: Added qtest to the list of accelerators]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now, the finalize_gic_version() code open coded what is essentially
a support bitmap match between host/emulation environment and desired
target GIC type.
This open coding leads to undesirable side effects. For example, a VM with
KVM and -smp 10 will automatically choose GICv3 while the same command
line with TCG will stay on GICv2 and fail the launch.
This patch combines the TCG and KVM matching code paths by making
everything a 2 pass process. First, we determine which GIC versions the
current environment is able to support, then we go through a single
state machine to determine which target GIC mode that means for us.
After this patch, the only user noticable changes should be consolidated
error messages as well as TCG -M virt supporting -smp > 8 automatically.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20221223090107.98888-2-agraf@csgraf.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently only support GICv2 emulation. To also support GICv3, we will
need to pass a few system registers into their respective handler functions.
This patch adds support for HVF to call into the TCG callbacks for GICv3
system register handlers. This is safe because the GICv3 TCG code is generic
as long as we limit ourselves to EL0 and EL1 - which are the only modes
supported by HVF.
To make sure nobody trips over that, we also annotate callbacks that don't
work in HVF mode, such as EL state change hooks.
With GICv3 support in place, we can run with more than 8 vCPUs.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20230128224459.70676-1-agraf@csgraf.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current FIFO handling code does not reset RXFE/RXFF flags when guest
resets FIFO by writing to UARTLCR register, although internal FIFO state
is reset to 0 read count. Actual guest-visible flag update will happen
only on next data read or write attempt. As a result of that any guest
that expects RXFE flag to be set (and RXFF to be cleared) after resetting
FIFO will never see that happen.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230123162304.26254-5-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Previous change slightly modified the way we handle data writes when
FIFO is disabled. Previously we kept incrementing read_pos and were
storing data at that position, although we only have a
single-register-deep FIFO now. Then we changed it to always store data
at pos 0.
If guest disables FIFO and the proceeds to read data, it will work out
fine, because we still read from current read_pos before setting it to
0.
However, to make code less fragile, introduce a post_load hook for
PL011State and move fixup read FIFO state when FIFO is disabled. Since
we are introducing a post_load hook, also do some sanity checking on
untrusted incoming input state.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Message-id: 20230123162304.26254-3-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 can be in either of 2 modes depending guest config: FIFO and
single register. The last mode could be viewed as a 1-element-deep FIFO.
Current code open-codes a bunch of depth-dependent logic. Refactor FIFO
depth handling code to isolate calculating current FIFO depth.
One functional (albeit guest-invisible) side-effect of this change is
that previously we would always increment s->read_pos in UARTDR read
handler even if FIFO was disabled, now we are limiting read_pos to not
exceed FIFO depth (read_pos itself is reset to 0 if user disables FIFO).
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-2-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Block layer patches
- qemu-img info: Show protocol-level information
- Move more functions to coroutines
- Make coroutine annotations ready for static analysis
- qemu-img: Fix exit code for errors closing the image
- qcow2 bitmaps: Fix theoretical corruption in error path
- pflash: Only load non-zero parts of backend image to save memory
- Code cleanup and test case improvements
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmPajLURHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9aLjg//bk2uodtEZ1X1y/vU3Lmcqd2wh9gv4f9L
# csFFf17rrxce/m+4daVISHAzS+Zrwpgixt+vMm2dP+jQTZOg0G7/rcaRYYAYa29Y
# Lepr2Qsz0V6HnNpuvUE5hrXiJXU7w5InikLlnoTnwa2H2Nr/wMlzkPX1wh4OdaBy
# 5KG/sjGVsaotrIdYjI3HnTvU/eytn1IcvLwqcTP2M7u8UMNyZkALyDjbC5QxBkwh
# TPVXNGCeDrD6atDOvsmBCkNM3kTmfsGoP5mYyJK5V6iARYV19Nt8tdmt094EFmHk
# VBgeY9y+Q6BctcDe31961+oFqGrsLnT3J7mHDhAoaO0BM8wwWCHfCA7yasmGjCj5
# HGE7/UJ8DYwGQ9T9N8gsx8NmsfyWgIcyRQGuzld72B4FTzES9NXS1JTUFAZHrDUl
# IIaL5bh8aycBKprDBTwvz07a6sDkvmxiR2G0TuS7kFev5O7+qW9dH517PWOWbsRA
# 3+ICzsHCUE2GLi83KkRkBEqRW0CnNmA9qzWNdPdQ0egsEAtNqmJGaFPRLYqQ0ZwR
# gbu7+eK4kUyfqpqieeFxBY53THLE4yxZ3lcg4yFoQWQfKdTCYo69qUNK5AV1hvKY
# TzNAuNbOsipL06dRWy4jInbhzenbiYechyEuoqFv0PpHe1D+JrL8QA2hI/JHDwls
# enNpKYXdkn4=
# =Wf8w
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 01 Feb 2023 16:00:53 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (38 commits)
qemu-img: Change info key names for protocol nodes
qemu-img: Let info print block graph
iotests/106, 214, 308: Read only one size line
iotests: Filter child node information
block/qapi: Add indentation to bdrv_node_info_dump()
block/qapi: Introduce BlockGraphInfo
block/qapi: Let bdrv_query_image_info() recurse
qemu-img: Use BlockNodeInfo
block: Split BlockNodeInfo off of ImageInfo
block/vmdk: Change extent info type
block/file: Add file-specific image info
block: Improve empty format-specific info dump
block/nbd: Add missing <qemu/bswap.h> include
block: Rename bdrv_load/save_vmstate() to bdrv_co_load/save_vmstate()
block: Convert bdrv_debug_event() to co_wrapper_mixed
block: Convert bdrv_lock_medium() to co_wrapper
block: Convert bdrv_eject() to co_wrapper
block: Convert bdrv_get_info() to co_wrapper_mixed
block: Convert bdrv_get_allocated_file_size() to co_wrapper
block: use bdrv_co_refresh_total_sectors when possible
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Testing, docs, semihosting and plugin updates
- update playbooks for custom runners
- add section timing support to gitlab
- upgrade fedora images to 37
- purge perl from the build system and deps
- disable unstable tests in CI
- improve intro, emulation and semihosting docs
- semihosting bug fix and O_BINARY default
- add memory-sve test
- fix some races in qht
- improve plugin handling of memory helpers
- optimise plugin hooks
- fix some plugin deadlocks
- reduce win64-cross build time by dropping some targets
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmPb3fgACgkQ+9DbCVqe
# KkQbXAf9Eoc+PdNvafbqzH/blPjvd9ve8pJ+GcPDukNXwxP8OF/jFEJUQ1E7l9O7
# y0qV4akKCdIqVice4R5bK2CAq44Y3aut8SDf56C8E3Riha2zA2RbQWOv/zCvA3OP
# LFF+OaXZyg4JTR48HUKzh9ei2bd1+ccBSUe+xlRi59XaV5K8+5bmcZj10QKUR0lD
# 0HC5auEWWpayvd5D7Da15C7+oVY3LMCFxSdpHwbuIPPan/TRo5yqMI6ChYDKB8QD
# gdwMCL8znj2ADCTBftyBDYDAtjKVyLQidf7KdQHiSF+nmXYopS6SbsPCOMtJqCMH
# tXcKAIxs/MEntPrWTKTdtdnzotJVKw==
# =AtfN
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 02 Feb 2023 15:59:52 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-jan-omnibus-020223-1' of https://gitlab.com/stsquad/qemu: (36 commits)
gitlab: cut even more from cross-win64-system build
plugins: Iterate on cb_lists in qemu_plugin_user_exit
cpu-exec: assert that plugin_mem_cbs is NULL after execution
tcg: exclude non-memory effecting helpers from instrumentation
translator: always pair plugin_gen_insn_{start, end} calls
plugins: fix optimization in plugin_gen_disable_mem_helpers
plugins: make qemu_plugin_user_exit's locking order consistent with fork_start's
util/qht: use striped locks under TSAN
thread: de-const qemu_spin_destroy
util/qht: add missing atomic_set(hashes[i])
cpu: free cpu->tb_jmp_cache with RCU
tests/tcg: add memory-sve test for aarch64
semihosting: add O_BINARY flag in host_open for NT compatibility
semihosting: Write back semihosting data before completion callback
docs: add an introduction to the system docs
semihosting: add semihosting section to the docs
docs: add a new section to outline emulation support
docs: add hotlinks to about preface text
MAINTAINERS: Fix the entry for tests/tcg/nios2
gitlab: wrap up test results for custom runners
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit bd688fc931 "accel: introduce accelerator blocker API" aded
include/sysemu/accel-blocker.h and accel/accel-blocker.c. MAINTAINERS
covers the latter in section "Guest CPU Cores (other accelerators) /
Overall", but not the former. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230119091545.3116376-3-armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
* qtest improvements
* Remove the deprecated OTP config of sifive_u
* Add libfdt to some of our CI jobs that were still missing it
* Use __builtin_bswap() everywhere (all compiler versions support it now)
* Deprecate the HAXM accelerator
* Document PCI devices handling on s390x
* Make Audiodev introspectable
* Improve the runtime of some CI jobs
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmPY59YRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXzhxAAmoq2j2sbAf2Vr9tz6Ez2p9oKNYnzUEWb
# NGXdvQMcVFKIdjvSYt5ozLC53OFIzuS74X7oHKbdLvGzez3nMCijZIbzN6vNnvd9
# HNGum4blNwHEfQcY9hr9y30Iurc7CQu6VtwGF+XXdzQZDbPz1Z4AWvtPTLcTbkxa
# PskYJfFvow/oaTHDA/7t+90cxCOixKvQMKXL5ATCtMRGnjlbOAEoPbXUB+yM24mk
# 9qp1L/8h8pvXfeXlFj+KETmu+eE5ETEOQtqc2KhQqqze2+VMKYxSX2H+sNkJBPDP
# En8Mpy+fEdefu8Jcu+M2kMLhf1f3LVf9uARhLZY4/xmOYFg+F3xzwpshnH1bs+Kw
# IzWP84uHjE77jSy/wKvYiCx2hdCDwO0G+zym67D1fPzvjzKzUNprV4OIuRzTWah3
# 6Zli5uuaLrBNjR8SJB1HDmLGKDFgToH9dzfLPtDmW8UPJGkAGcBbPKktLTe5y/4E
# del99NqpTx5SAqMmbSMRPZ/vZ7ITdfB0Av3a0GdO8j7eSPb9BOsoZOVD2/iUzab/
# P0dBuNqMM8fwywVKqcK+0CJ/npWIJvOqqlwSDqhY1A78G/uRuapOqUwsB/LWRFv5
# /1VvHfA2rv4l9o66N5jssS5/D1v5p/UBB6JvlTUvuoJMFTXa9de9XFxYxfkyiaAz
# LJl+Dh+aeWk=
# =uq7y
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 31 Jan 2023 10:05:10 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-01-31' of https://gitlab.com/thuth/qemu: (27 commits)
gitlab-ci.d/buildtest: Merge the --without-default-* jobs
tests/qtest/display-vga-test: Add proper checks if a device is available
gitlab-ci.d/buildtest: Remove ppc-softmmu from the clang-system job
qapi, audio: Make introspection reflect build configuration more closely
qapi, audio: add query-audiodev command
docs/s390x/pcidevices: document pci devices on s390x
tests/qtest/boot-serial-test: Constify tests[] array
tests/qtest/vnc-display-test: Disable on Darwin
tests/qtest/vnc-display-test: Use the 'none' machine
tests/qtest/vnc-display-test: Suppress build warnings on Windows
tests/tcg: Do not build/run TCG tests if TCG is disabled
docs/about/deprecated: Mark HAXM in QEMU as deprecated
MAINTAINERS: Abort HAXM maintenance
qemu/bswap: Use compiler __builtin_bswap() on NetBSD
qemu/bswap: Use compiler __builtin_bswap() on FreeBSD
qemu/bswap: Use compiler __builtin_bswap() on Haiku
qemu/bswap: Remove <byteswap.h> dependency
qemu/bswap: Replace bswapXXs() by compiler __builtin_bswap()
qemu/bswap: Replace bswapXX() by compiler __builtin_bswap()
tests/docker/dockerfiles: Add libfdt to the i386 and to the riscv64 container
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are actually a whole bunch of helpers that don't affect memory
that we shouldn't instrument. They are helpfully identified by the
TCG_CALL_NO_SIDE_EFFECTS flag which marks out lookup_tb_ptr as well as
a lot of the maths helpers. To avoid the string compare we introduce a
new flag for plugin internals so we skip that too.
Related: #1381
Signed-off-by: Emilio Cota <cota@braap.org>
Message-Id: <20230108164731.61469-4-cota@braap.org>
[AJB: updated to skip all no SE plugins, add flag for plugin helper]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230124180127.1881110-34-alex.bennee@linaro.org>
We were mistakenly checking tcg_ctx->plugin_insn as a canary to know
whether the TB had emitted helpers that might have accessed memory.
The problem is that tcg_ctx->plugin_insn gets updated on every
instruction in the TB, which results in us wrongly performing the
optimization (i.e. not clearing cpu->plugin_mem_cbs) way too often,
since it's not rare that the last instruction in the TB doesn't
use helpers.
Fix it by tracking a per-TB canary.
While at it, expand documentation.
Related: #1381
Signed-off-by: Emilio Cota <cota@braap.org>
Message-Id: <20230108164731.61469-2-cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230124180127.1881110-32-alex.bennee@linaro.org>
Fixes the appended use-after-free. The root cause is that
during tb invalidation we use CPU_FOREACH, and therefore
to safely free a vCPU we must wait for an RCU grace period
to elapse.
$ x86_64-linux-user/qemu-x86_64 tests/tcg/x86_64-linux-user/munmap-pthread
=================================================================
==1800604==ERROR: AddressSanitizer: heap-use-after-free on address 0x62d0005f7418 at pc 0x5593da6704eb bp 0x7f4961a7ac70 sp 0x7f4961a7ac60
READ of size 8 at 0x62d0005f7418 thread T2
#0 0x5593da6704ea in tb_jmp_cache_inval_tb ../accel/tcg/tb-maint.c:244
#1 0x5593da6704ea in do_tb_phys_invalidate ../accel/tcg/tb-maint.c:290
#2 0x5593da670631 in tb_phys_invalidate__locked ../accel/tcg/tb-maint.c:306
#3 0x5593da670631 in tb_invalidate_phys_page_range__locked ../accel/tcg/tb-maint.c:542
#4 0x5593da67106d in tb_invalidate_phys_range ../accel/tcg/tb-maint.c:614
#5 0x5593da6a64d4 in target_munmap ../linux-user/mmap.c:766
#6 0x5593da6dba05 in do_syscall1 ../linux-user/syscall.c:10105
#7 0x5593da6f564c in do_syscall ../linux-user/syscall.c:13329
#8 0x5593da49e80c in cpu_loop ../linux-user/x86_64/../i386/cpu_loop.c:233
#9 0x5593da6be28c in clone_func ../linux-user/syscall.c:6633
#10 0x7f496231cb42 in start_thread nptl/pthread_create.c:442
#11 0x7f49623ae9ff (/lib/x86_64-linux-gnu/libc.so.6+0x1269ff)
0x62d0005f7418 is located 28696 bytes inside of 32768-byte region [0x62d0005f0400,0x62d0005f8400)
freed by thread T148 here:
#0 0x7f49627b6460 in __interceptor_free ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:52
#1 0x5593da5ac057 in cpu_exec_unrealizefn ../cpu.c:180
#2 0x5593da81f851 (/home/cota/src/qemu/build/qemu-x86_64+0x484851)
Signed-off-by: Emilio Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230111151628.320011-2-cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230124180127.1881110-27-alex.bennee@linaro.org>
'lock_user' allocates a host buffer to shadow a target buffer,
'unlock_user' copies that host buffer back to the target and frees the
host memory. If the completion function uses the target buffer, it
must be called after unlock_user to ensure the data are present.
This caused the arm-compatible TARGET_SYS_READC to fail as the
completion function, common_semi_readc_cb, pulled data from the target
buffer which would not have been gotten the console data.
I decided to fix all instances of this pattern instead of just the
console_read function to make things consistent and potentially fix
bugs in other cases.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221012014822.1242170-1-keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230124180127.1881110-24-alex.bennee@linaro.org>
Drop the frankly misleading quickstart section for a more rounded
introduction section. This new section gives an overview of the
accelerators as well as a high level introduction to some of the key
features of the emulator. We also expand on a general form for a QEMU
command line with a hopefully not too scary worked example of what
this looks like.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Kashyap Chamarthy <kchamart@redhat.com>
Message-Id: <20230124180127.1881110-23-alex.bennee@linaro.org>
The main reason to do this is to document our O_BINARY implementation
decision somewhere. However I've also moved some of the implementation
details out of qemu-options and added links between the two. As a
bonus I've highlighted the scary warnings about host access with the
appropriate RST tags.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230124180127.1881110-22-alex.bennee@linaro.org>
Instead of spewing the whole log to stdout lets just define them as
build artefacts so we can examine them later. Where we are running
check-tcg run it first as those tests are yet to be integrated into
meson. To avoid confusion we don't run multiple check-tcg tests at
once.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230124180127.1881110-18-alex.bennee@linaro.org>
When flex is not available, binutils sources default to the
'missing' script, but the current script available is not in
the format expected by the 'configure' script:
$ ./configure
...
/usr/src/binutils/missing: Unknown `--run' option
Try `/usr/src/binutils/missing --help' for more information
configure: WARNING: `missing' script is too old or missing
...
checking for bison... bison -y
checking for flex... no
checking for lex... no
checking for flex... /usr/src/binutils/missing flex
$ make
...
updating ldgram.h
gcc -DHAVE_CONFIG_H -I. -I. -I. -D_GNU_SOURCE -I. -I. -I../bfd -I./../bfd -I./../include -I./../intl -I../intl -w -DLOCALEDIR="\"/usr/local/share/locale\"" -W -Wall -Wstrict-prototypes -Wmissing-prototypes -w -c `test -f 'ldgram.c' || echo './'`ldgram.c
`test -f ldlex.l || echo './'`ldlex.l
/bin/sh: 1: ldlex.l: not found
make[3]: *** [Makefile:662: ldlex.c] Error 127
make[3]: Leaving directory '/usr/src/binutils/ld'
make[2]: *** [Makefile:799: all-recursive] Error 1
By pass the 'missing' script use by directly installing 'flex'
in the container.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230112155643.7408-1-philmd@linaro.org>
Reviewed-by: Bastian-Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230124180127.1881110-14-alex.bennee@linaro.org>
We were using quite and old runner on our machines and running into
issues with stalling jobs. Gitlab in the meantime now reliably provide
the latest packaged versions of the runner under a stable URL. This
update:
- creates a per-arch subdir for builds
- switches from binary tarballs to deb packages
- re-uses the same binary for the secondary runner
- updates distro check for second to 22.04
Note this script isn't fully idempotent as we end up accumulating
runners especially during testing. However we also want to be able to
run twice with different GitLab keys (e.g. project and personal) so I
think we just have to be mindful of that during testing.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230124180127.1881110-2-alex.bennee@linaro.org>
Currently, when querying a qcow2 image, qemu-img info reports something
like this:
image: test.qcow2
file format: qcow2
virtual size: 64 MiB (67108864 bytes)
disk size: 196 KiB
cluster_size: 65536
Format specific information:
compat: 1.1
compression type: zlib
lazy refcounts: false
refcount bits: 16
corrupt: false
extended l2: false
Child node '/file':
image: test.qcow2
file format: file
virtual size: 192 KiB (197120 bytes)
disk size: 196 KiB
Format specific information:
extent size hint: 1048576
Notably, the way the keys are named is specific for image files: The
filename is shown under "image", the BDS driver under "file format", and
the BDS length under "virtual size". This does not make much sense for
nodes that are not actually supposed to be guest images, like the /file
child node shown above.
Give bdrv_node_info_dump() a @protocol parameter that gives a hint that
the respective node is probably just used for data storage and does not
necessarily present the data for a VM guest disk. This renames the keys
so that with this patch, the output becomes:
image: test.qcow2
[...]
Child node '/file':
filename: test.qcow2
protocol type: file
file length: 192 KiB (197120 bytes)
disk size: 196 KiB
Format specific information:
extent size hint: 1048576
(Perhaps we should also rename "Format specific information", but I
could not come up with anything better that will not become problematic
if we guess wrong with the protocol "heuristic".)
This change affects iotest 302, which has protocol node information in
its reference output.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-13-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For every node in the backing chain, collect its BlockGraphInfo struct
using bdrv_query_block_graph_info(). Print all nodes' information,
indenting child nodes and labelling them with a path constructed from
the child names leading to the node from the root (e.g. /file/file).
Note that we open each image with BDRV_O_NO_BACKING, so its backing
child is omitted from this graph, and thus presented in the previous
manner: By simply concatenating all images' information, separated with
blank lines.
This affects two iotests:
- 065: Here we try to get the format node's format specific information.
The pre-patch code does so by taking all lines from "Format specific
information:" until an empty line. This format specific information
is no longer followed by an empty line, though, but by child node
information, so limit the range by "Child node '/file':".
- 302: Calls qemu_img() for qemu-img info directly, which does not
filter the output, so the child node information ends up in the
output.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-12-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These tests read size information (sometimes disk size, sometimes
virtual size) from qemu-img info's output. Once qemu-img starts
printing info about child nodes, we are going to see multiple instances
of that per image, but these tests are only interested in the first one,
so use "head -n 1" to get it.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-11-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before we let qemu-img info print child node information, have
common.filter, common.rc, and iotests.py filter it from the test output
so we get as few reference output changes as possible.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-10-hreitz@redhat.com>
Tested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to let qemu-img info present a block graph, add a parameter to
bdrv_node_info_dump() and bdrv_image_info_specific_dump() so that the
information of nodes below the root level can be given an indentation.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-9-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduce a new QAPI type BlockGraphInfo and an associated
bdrv_query_block_graph_info() function that recursively gathers
BlockNodeInfo objects through a block graph.
A follow-up patch is going to make "qemu-img info" use this to print
information about all nodes that are (usually implicitly) opened for a
given image file.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-8-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no real reason why bdrv_query_image_info() should generally not
recurse. The ImageInfo struct has a pointer to the backing image, so it
should generally be filled, unless the caller explicitly opts out.
This moves the recursing code from bdrv_block_device_info() into
bdrv_query_image_info().
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-7-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu-img info never uses ImageInfo's backing-image field, because it
opens the backing chain one by one with BDRV_O_NO_BACKING, and prints
all backing chain nodes' information consecutively. Use BlockNodeInfo
to make it clear that we only print information about a single node, and
that we are not using the backing-image field.
Notably, bdrv_image_info_dump() does not evaluate the backing-image
field, so we can easily make it take a BlockNodeInfo pointer (and
consequentially rename it to bdrv_node_info_dump()). It makes more
sense this way, because again, the interface now makes it syntactically
clear that backing-image is ignored by this function.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-6-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ImageInfo sometimes contains flat information, and sometimes it does
not. Split off a BlockNodeInfo struct, which only contains information
about a single node and has no link to the backing image.
We do this so we can extend BlockNodeInfo to a BlockGraphInfo struct,
which has links to all child nodes, not just the backing node. It would
be strange to base BlockGraphInfo on ImageInfo, because then this
extended struct would have two links to the backing node (one in
BlockGraphInfo as one of all the child links, and one in ImageInfo).
Furthermore, it is quite common to ignore the backing-image field
altogether: bdrv_query_image_info() does not set it, and
bdrv_image_info_dump() does not evaluate it. That signals that we
should have different structs for describing a single node and one that
has a link to the backing image.
Still, bdrv_query_image_info() and bdrv_image_info_dump() are not
changed too much in this patch. Follow-up patches will handle them.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-5-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VMDK's implementation of .bdrv_get_specific_info() returns information
about its extent files, ostensibly in the form of ImageInfo objects.
However, it does not get this information through
bdrv_query_image_info(), but fills only a select few fields with custom
information that does not always match the fields' purposes.
For example, @format, which is supposed to be a block driver name, is
filled with the extent type, e.g. SPARSE or FLAT.
In ImageInfo, @compressed shows whether the data that can be seen in the
image is stored in compressed form or not. For example, a compressed
qcow2 image will store compressed data in its data file, but when
accessing the qcow2 node, you will see normal data. This is not how
VMDK uses the @compressed field for its extent files: Instead, it
signifies whether accessing the extent file will yield compressed data
(which the VMDK driver then (de-)compresses).
Create a new structure to represent the extent information. This allows
us to clarify the fields' meanings, and it clearly shows that these are
not complete ImageInfo objects. (That is, if a user wants an extent
file's ImageInfo object, they will need to query it separately, and will
not get it from ImageInfoSpecificVmdk.extents.)
Note that this removes the last use of ['ImageInfo'] (i.e. an array of
ImageInfo objects), so the QAPI generator will no longer generate
ImageInfoList by default. However, we use it in qemu-img.c, so we need
to create a dummy object to force the generate to create that type,
similarly to DummyForceArrays in machine.json (introduced in commit
9f08c8ec73 ("qapi: Lazy creation of array
types")).
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-4-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When a block driver supports obtaining format-specific information, but
that object only contains optional fields, it is possible that none of
them are present, so that dump_qobject() (called by
bdrv_image_info_specific_dump()) will not print anything.
The callers of bdrv_image_info_specific_dump() put a header above this
information ("Format specific information:\n"), which will look strange
when there is nothing below. Modify bdrv_image_info_specific_dump() to
print this header instead of its callers, and only if there is indeed
something to be printed.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220620162704.80987-2-hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The inlined nbd_readXX() functions call beXX_to_cpu(), themselves
declared in <qemu/bswap.h>. This fixes when refactoring:
In file included from ../../block/nbd.c:44:
include/block/nbd.h: In function 'nbd_read16':
include/block/nbd.h:383:12: error: implicit declaration of function 'be16_to_cpu' [-Werror=implicit-function-declaration]
383 | *val = be##bits##_to_cpu(*val); \
| ^~
include/block/nbd.h:387:1: note: in expansion of macro 'DEF_NBD_READ_N'
387 | DEF_NBD_READ_N(16) /* Defines nbd_read16(). */
| ^~~~~~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221125175328.48539-1-philmd@linaro.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_debug_event() is categorized as an I/O function, and it currently
doesn't run in a coroutine. We should let it take a graph rdlock since
it traverses the block nodes graph, which however is only possible in a
coroutine.
Therefore turn it into a co_wrapper_mixed to move the actual function
into a coroutine where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-14-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_lock_medium() is categorized as an I/O function, and it currently
doesn't run in a coroutine. We should let it take a graph rdlock since
it traverses the block nodes graph, which however is only possible in a
coroutine.
The only caller of this function is blk_lock_medium(). Therefore make
blk_lock_medium() a co_wrapper, so that it always creates a new
coroutine, and then make bdrv_lock_medium() a coroutine_fn where the
lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-13-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_eject() is categorized as an I/O function, and it currently
doesn't run in a coroutine. We should let it take a graph rdlock since
it traverses the block nodes graph, which however is only possible in a
coroutine.
The only caller of this function is blk_eject(). Therefore make
blk_eject() a co_wrapper, so that it always creates a new coroutine, and
then make bdrv_eject() coroutine_fn where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-12-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_get_info() is categorized as an I/O function, and it currently
doesn't run in a coroutine. We should let it take a graph rdlock since
it traverses the block nodes graph, which however is only possible in a
coroutine.
Therefore turn it into a co_wrapper to move the actual function into a
coroutine where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-11-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_get_allocated_file_size() is categorized as an I/O function, and it
currently doesn't run in a coroutine. We should let it take a graph
rdlock since it traverses the block nodes graph, which however is only
possible in a coroutine.
Therefore turn it into a co_wrapper to move the actual function into a
coroutine where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-10-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only difference is that blk_ checks if the block is available,
but this check is already performed above in blk_check_byte_request().
This is in preparation for the graph rdlock, which will be taken
by both the callers of blk_check_byte_request() and blk_getlength().
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-8-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriver->bdrv_getlength is categorized as IO callback, and it
currently doesn't run in a coroutine. We should let it take a graph
rdlock since the callback traverses the block nodes graph, which however
is only possible in a coroutine.
Therefore turn it into a co_wrapper to move the actual function into a
coroutine where the lock can be taken.
Because now this function creates a new coroutine and polls, we need to
take the AioContext lock where it is missing, for the only reason that
internally co_wrapper calls AIO_WAIT_WHILE and it expects to release the
AioContext lock.
This is especially messy when a co_wrapper creates a coroutine and polls
in bdrv_open_driver, because this function has so many callers in so
many context that it can easily lead to deadlocks. Therefore the new
rule for bdrv_open_driver is that the caller must always hold the
AioContext lock of the given bs (except if it is a coroutine), because
the function calls bdrv_refresh_total_sectors() which is now a
co_wrapper.
Once the rwlock is ultimated and placed in every place it needs to be,
we will poll using AIO_WAIT_WHILE_UNLOCKED and remove the AioContext
lock.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-7-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The name is not good, not the least because we are going to convert this
to a generated co_wrapper, which adds a _co infix after the first part
of the name.
No functional change intended.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-6-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_is_inserted() is categorized as an I/O function, and it currently
doesn't run in a coroutine. We should let it take a graph rdlock since
it traverses the block nodes graph, which however is only possible in a
coroutine.
Therefore turn it into a co_wrapper to move the actual function into a
coroutine where the lock can be taken.
At the same time, add also blk_is_inserted as co_wrapper_mixed, since it
is called in both coroutine and non-coroutine contexts.
Because now this function creates a new coroutine and polls, we need to
take the AioContext lock where it is missing, for the only reason that
internally c_w_mixed_bdrv_rdlock calls AIO_WAIT_WHILE and it expects to
release the AioContext lock. Once the rwlock is ultimated and placed in
every place it needs to be, we will poll using AIO_WAIT_WHILE_UNLOCKED
and remove the AioContext lock.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-5-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriver->bdrv_io_unplug is categorized as IO callback, and it
currently doesn't run in a coroutine. We should let it take a graph
rdlock since the callback traverses the block nodes graph, which however
is only possible in a coroutine.
The only caller of this function is blk_io_unplug(), therefore make
blk_io_unplug() a co_wrapper, so that we're always running in a
coroutine where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-4-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriver->bdrv_io_plug is categorized as IO callback, and it
currently doesn't run in a coroutine. We should let it take a graph
rdlock since the callback traverses the block nodes graph, which however
is only possible in a coroutine.
The only caller of this function is blk_io_plug(), therefore make
blk_io_plug() a co_wrapper, so that we're always running in a coroutine
where the lock can be taken.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230113204212.359076-3-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This tests that when an error happens while writing back bitmaps to the
image file in qcow2_inactivate(), 'qemu-img bitmap/commit' actually
return an error value in their exit code instead of making the operation
look successful to scripts.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230112191454.169353-5-kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Let's safe some CI minutes by merging these two jobs. We can now
also drop "--disable-capstone" since the capstone submodule has
been removed a while ago. We should rather test --disable-fdt now
to check a compilation without the "dtc" submodule (for this we
have to drop i386-softmmu from the target list unfortunately).
Additionally, the qtests with s390x and sh4 are not read for
"--without-default-devices" yet, so we can only test mips64 and
avr here now.
Message-Id: <20230130104446.1286773-5-thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
display-vga-test currently tries to guess the usable VGA devices
according to the target architecture that is used for the test.
This of course does not work if QEMU has been built with the
"--without-default-devices" configure switch. To fix this, use the
qtest_has_device() function for the decision instead. This way
we can also consolidate most of the test functions into one single
function (that takes a parameter with the device name now), except
for the multihead test that tries to instantiate two devices and
thus is a little bit different.
Message-Id: <20230130104446.1286773-4-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are also compile-testing ppc64-softmmu with clang in the "tsan-build"
job, and ppc64-softmmu covers pretty much the same code as ppc-softmmu,
so we should not lose much test coverage here by removing ppc-softmmu
from the "clang-system" job.
Message-Id: <20230130104446.1286773-2-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently the -audiodev accepts any audiodev type regardless of what is
built in to QEMU. An error only occurs later at runtime when a sound
device tries to use the audio backend.
With this change QEMU will immediately reject -audiodev args that are
not compiled into the binary. The QMP schema will also be introspectable
to identify what is compiled in.
This also helps to avoid compiling code that is not required in the
binary. Note: When building the audiodevs as modules, the patch only
compiles out code for modules that we don't build at all.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Rebase, take sndio and dbus devices into account]
Message-Id: <20230123083957.20349-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Way back in QEMU 4.0, the -audiodev command line option was introduced
for configuring audio backends. This CLI option does not use QemuOpts
so it is not visible for introspection in 'query-command-line-options',
instead using the QAPI Audiodev type. Unfortunately there is also no
QMP command that uses the Audiodev type, so it is not introspectable
with 'query-qmp-schema' either.
This introduces a 'query-audiodev' command that simply reflects back
the list of configured -audiodev command line options. This alone is
maybe not very useful by itself, but it makes Audiodev introspectable
via 'query-qmp-schema', so that libvirt (and other upper layer tools)
can discover the available audiodevs.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Update for upcoming QEMU v8.0, and use QAPI_LIST_PREPEND]
Message-Id: <20230123083957.20349-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This reverts commit a7f523c7d1.
The nested event loop is broken by design. It's only user was removed.
Drop the code as well so that nobody ever tries to use it again.
I had to fix a couple of trivial conflicts around return values because
of 025faa872b ("vhost-user: stick to -errno error return convention").
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-3-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This reverts commit db8a3772e3.
Motivation : this is breaking vhost-user with DPDK as reported in [0].
Received unexpected msg type. Expected 22 received 40
Fail to update device iotlb
Received unexpected msg type. Expected 40 received 22
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 1 ring restore failed: -71: Protocol error (71)
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 0 ring restore failed: -71: Protocol error (71)
unable to start vhost net: 71: falling back on userspace virtio
The failing sequence that leads to the first error is :
- QEMU sends a VHOST_USER_GET_STATUS (40) request to DPDK on the master
socket
- QEMU starts a nested event loop in order to wait for the
VHOST_USER_GET_STATUS response and to be able to process messages from
the slave channel
- DPDK sends a couple of legitimate IOTLB miss messages on the slave
channel
- QEMU processes each IOTLB request and sends VHOST_USER_IOTLB_MSG (22)
updates on the master socket
- QEMU assumes to receive a response for the latest VHOST_USER_IOTLB_MSG
but it gets the response for the VHOST_USER_GET_STATUS instead
The subsequent errors have the same root cause : the nested event loop
breaks the order by design. It lures QEMU to expect responses to the
latest message sent on the master socket to arrive first.
Since this was only needed for DAX enablement which is still not merged
upstream, just drop the code for now. A working solution will have to
be merged later on. Likely protect the master socket with a mutex
and service the slave channel with a separate thread, as discussed with
Maxime in the mail thread below.
[0] https://lore.kernel.org/qemu-devel/43145ede-89dc-280e-b953-6a2b436de395@redhat.com/
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2155173
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-2-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
We are facing the issues that our test logs in the gitlab CI are
too big (and thus cut off). The bios-tables-test is one of the few
qtests that prints many lines of output by default when running with
V=1, so it contributes to this problem. Almost all other qtests are
silent with V=1 and only print debug messages with V=2 and higher.
Thus let's change the bios-tables-test to behave more like the
other tests and only print the debug messages with V=2 (or higher).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230118125132.1694469-1-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Generating slots descriptions populated by non-hotpluggable devices
is akward at best and complicates hotplug path (build_append_pcihp_slots)
needlessly, and builds only dynamic _DSM for such slots which is overlkill.
Clean it up and let non-hotplug path (build_append_pci_bus_devices)
to handle that task.
Such clean up effectively drops dynamic _DSM methods on non-hotpluggable
slots (even though bus itself is hotpluggable), but in practice it
affects only built-in devices (ide controllers/various bridges) that don't
use acpi-index anyways so effectively it doesn't matter (NICs are hotpluggble).
Follow up series will add static _DSM for non-hotpluggble devices/buses
that will not depend on ACPI PCI hotplug at all, and potentially would
allows us to reuse non-hotplug path elsewhere (PBX/microvm/arm-virt),
including new support for acpi-index for non-hotpluggable devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-40-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
coldplugged bridges are not unpluggable, so there is no need
to describe slots where they are plugged as hotpluggable. To
that effect we have a condition that marks slot as non-hotpluggable
if it's populated by coldplugged bridge and prevents generation
_SUN/_EJ0 objects for it. That leaves dynamic _DSM method on
such slot (which also depends on BSEL and pcihp hardware).
This _DSM method provides only dynamic acpi-index support so far,
which is not actually used/supported by linux kernel for bridges
and it's doubtful there will be need for it at all.
So it's rather pointless to generate acpi-index related AML
for bridges and we can simplify hotplug slots generator a bit
more by completely ignoring coldplugged bridges on hotplug path.
Another point in favor of dropping dynamic _DSM support, is
that we can replace it with static _DSM if necessary since
a slot with bridge can't change during VM runtime and without
any dependency on ACPI PCI hotplug at that.
Later I plan to implement bridge specific static _DSM
PCI Firmware Specification 3.2
4.6.5. _DSM for Ignoring PCI Boot Configurations
part of spec, to fix longstanding issue with fixed IO/MEM
resource assignment that often leads to hotplugged device
being in-operational within the guest due limited IO/MEM
windows programmed on bridge at boot time.
Expected change when coldplugged bridge is ignored by hotplug
code, should look like:
- Scope (S18)
- {
- Name (ASUN, 0x03)
- Method (_DSM, 4, Serialized) // _DSM: Device-Specific Method
- {
- Local0 = Package (0x02)
- {
- BSEL,
- ASUN
- }
- Return (PDSM (Arg0, Arg1, Arg2, Arg3, Local0))
- }
- }
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-37-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split build_append_pci_bus_devices() onto generic part that builds
AML descriptions only for populated slots which is applicable to
both hotplug disabled and enabled bridges. And a hotplug only
part that complements generic AML with hotplug depended bits
(that depend on BSEL), like _SUN/_EJ0 entries, dynamic _DSM.
Hotplug part, will generate full 'Device' descriptors for
non-populated slots (like it used to be) and complementary
'Scope' descriptors for populated slots that are hotplug capable.
i.e. something like this:
- ...
+ Name (BSEL, 0x03)
+ Scope (S00)
+ {
+ Name (ASUN, Zero)
+ Method (_DSM, 4, Serialized) // _DSM: Device-Specific Method
+ {
+ Local0 = Package (0x02)
+ {
+ BSEL,
+ ASUN
+ }
+ Return (PDSM (Arg0, Arg1, Arg2, Arg3, Local0))
+ }
+ [ ... other hotplug depended bits ]
+ }
While generic build_append_pci_bus_devices() still calls hotplug part at
its end it doesn't really depend on any hotplug bits anymore and later
both could be completely separated when it's necessary.
Main benefit though is that both build_append_pci_bus_devices() and
build_append_pcihp_slots() become more readable and it makes easier
to modify them with less risk of affecting another part. Also it opens
possibility to re-use generic part elsewhere (microvm, arm/virt).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-34-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
... so that the concrete impl. won't has to duplicate it
every time. By default it doesn't do anything unless leaf class
defines and sets AcpiDevAmlIfClass::build_dev_aml handler.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-29-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Before switching pci bridges to AcpiDevAmlIf interface, ensure that
ignored slots are handled correctly.
(existing rule works but only if bridge doesn't have AcpiDevAmlIf interface).
While at it rewrite related comments to be less confusing (hopefully).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-28-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
previous commit added endpoint devices to bridge testcases,
which exposes extra non-hotpluggable slot in DSDT on bus where
hotplug is not available.
It should look like this (numbers may vary):
+ Device (S28)
+ {
+ Name (_ADR, 0x00050000) // _ADR: Address
+ }
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-27-imammedo@redhat.com>
count number of PCNT methods that actually call Notify
and if there aren't any, drop PCNT altogether.
It mostly affects 'Q35' tests where there is no root-ports
/bridges attached and 'PC' machine when ACPI PCI hotplug is
completely disabled.
Expected ASL change:
- Method (PCNT, 0, NotSerialized)
- {
- }
...
Method (_E01, 0, NotSerialized) // _Exx: Edge-Triggered GPE
{
- Acquire (\_SB.PCI0.BLCK, 0xFFFF)
- \_SB.PCI0.PCNT ()
- Release (\_SB.PCI0.BLCK)
}
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-23-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it's a stepping stone to making build_append_pci_bus_devices() suitable
for AcpiDevAmlIfClass:build_dev_aml callback and lets further simplify
it by separating PCNT generation from slots descriptions.
It also makes PCNT callchain ASL much more readable since callchain
not longer cluttered by slots descriptors.
Plus, move will let next patch easily drop empty PCNT (pc/q35)
when there is nothing hotpluggable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-22-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.. and use only BSEL presence to decide on how PCNT should be composed.
That simplifies possible combinations to consider, but mainly it makes
PCIHP AML be governed only by BSEL, which is property of PCIBus
(aka part of bridge) and as result it opens possibility to convert
build_append_pci_bus_devices() into AcpiDevAmlIf::build_dev_aml
callback to make bridges self describing.
PS:
used approach leaves unused PCNT, when ACPI hotplug is completely
disabled but that's harmless and followup commits will get rid of
it later.
Scope (PCI0)
...
Method (PCNT, 0, NotSerialized)
{
}
...
}
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-19-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hotplugged bridges should not be described in DSDT,
while it works on cold boot, some ACPPI PCI code
are invoked during reboot.
This patch will let us catch unexpected AML if hotplug
checks are broken.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-17-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
if the function is called the 2nd time within the same qtest session,
it will prematurely return before boot sector is executed due to
remaining signature.
Follow up patch will add VM reboot to a test case and will
call boot_sector_test() again within the same qtest env,
which may lead to above issue.
To fix it make sure signature in VM RAM is no more before
exiting boot_sector_test(), so next time it's called it
will wait boot sector is completed again.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-16-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
with previous commit fixing malformed PCNT calls to hotplugged
bridges, it should be possible add coldplug/hotplug test when
describing PCI topology in DSDT without breeaking CI.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-15-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If test case was started in paused mode (-S CLI option) and then
allowed to continue via QMP, boot_sector_test could assert on
transient state with following error:
assertion failed (qdict_get_try_str(qret, "status") == "running"): (NULL == "running")
Instead of crashing test if 'status' is not available yet, skip check
and repeat iteration again after TEST_DELAY has elapsed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-14-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When QEMU is started with hotplugged bridges (think migration):
QEMU -S -monitor stdio \
-device pci-bridge,chassis_nr=1 \
-device pci-bridge,bus=pci.1,addr=1.0,chassis_nr=2
(qemu) device_add pci-bridge,id=hpbr,bus=pci.1,addr=2.0,chassis_nr=3
(qemu) cont
it will generate AML calls to hpbr's PCNT, which doesn't exists
since it's hotplugged bridge. As result DSDT becomes malformed,
with consequences that hotplug might stop working at best or
crash guest OS at worst, when it attempts to call non existing
PCNT method or during OS guest reboot when parsing DSDT again.
IASL de-compiles malformed AML of above config DSDT as:
+ External (_SB_.PCI0.S18_.S10_.PCNT, MethodObj) // Warning: Unknown method, guessing 1 arguments
+ External (_SB_.PCI0.S18_.S19_.PCNT, MethodObj) // Warning: Unknown method, guessing 2 arguments
...
BNUM = One
DVNT (PCIU, One)
DVNT (PCID, 0x03)
- ^S08.PCNT ()
+ ^S19.PCNT (^S10.PCNT (^S08.PCNT ()))
}
}
With BSEL assignment limited only to coldplugged bridges [1],
it should be possible to add PCNT call to a child bridge only
if the child has BSEL property, otherwise ignore it since it's
hotplugged. Which should fix the issue.
1) ("pci: acpihp: assign BSEL only to coldplugged bridges")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-13-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI PCI hotplug would broken after bridge hotplug and then migration
if hotplugged bridge were specified on target at command line.
Currently it's not possible since, 'hotplugged' property was made
read-only for some time now.
The issue would happen due to BSEL being assigned to all bridges
during 1st 'reset':
source seq:
1. start 'pc' machine => sets BSEL to 0 on pci.0 (host-bridge)
2. hotplug bridge, no bsel is assigned (so far is ok)
target seq:
1. start 'pc' machine with
-S -device pci-bridge,id=hp_br,hotplugged=on
BSEL gets assigned to as follows
hp_br: 0
pci.0: 1
as result hotplug requests with migrated AML generated on source
would be misdirected to 'hp_br' instead of intended pci.0
While it's not issue at the moment, it's based on implicit assumptions
* 'hotplugged' property is read-only
* 1st reset happens before QEMU drops into monitor mode
which lets add hotplugged on source bridges as hotplugged ones
(anything added at that stage counts as hotplugged
(yet another assumption))
All of it looks too fragile to me, so lets restrict BSEL only
to cold-plugged bridges explicitly.
Migration wise it shouldn't break anything since assignment order
stays the same:
* user can't specify 'hotplugged=on' on CLI
* user can't specify 'hotplugged=off' at monitor stage or later
on older QEMU versions where 'hotplugged' is RW, hotplug is broken
after migration anyways and we cannot do anything to fix that.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-12-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
piix4_pm_reset() is calling acpi_pcihp_reset() when ACPI PCI hotplug
is disabled, which leads to assigning BSEL properties to bridges on path
acpi_set_bsel()
...
if (qbus_is_hotpluggable(BUS(bus))) {
// above happens to be true by default (though it's SHPC hotplug handler)
// set BSEL
}
At the moment the issue is masked by the fact that we use not only BSEL,
to decide if we should generated hoplug AML but also pcihp_bridge_en knob.
However the later patches will drop dependency on pcihp_bridge_en,
and use only BSEL exclusively to decide if hotplug AML for slots should be built,
which exposes issue.
We should not ever call acpi_pcihp_reset() if ACPI PCI hotplug is disabled,
make it so.
PS:
* Q35 does the right thing (i.e. it calls acpi_pcihp_reset only when pcihp is enabled)
* the issue also makes acpi_pcihp_update() logic run on SHPC enabled bridges,
which seems to be harmless
Fixes: 3d7e78aa77 ("Introduce a new flag for i440fx to disable PCI hotplug on the root bus")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-11-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When ACPI PCI hotplug for Q35 was introduced (6.1), it was implemented
by hiding HPC capability on PCIE slot. That however led to a number of
regressions and to fix it, it was decided to keep HPC cap exposed
in ACPI PCI hotplug case and force guest in ACPI PCI hotplug mode
by other means [1].
That reduced meaning of x-native-hotplug to a compat knob [2] for
broken 6.1 machine type.
Rename property to match its current purpose.
1) 211afe5c69 (hw/i386/acpi-build: Deny control on PCIe Native Hot-plug in _OSC)
2) c318bef762 (hw/acpi/ich9: Add compat prop to keep HPC bit set for 6.1 machine type)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-10-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'use_uefi' is used for the flag is a part of 'test_data *data'
argument that is passed to the same functions, which
makes use_uefi argument redundant.
Drop it and use 'data::uefi_*' directly, instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The setup_data links are appended to the compressed kernel image. Since
the kernel image is typically loaded at 0x100000, setup_data lives at
`0x100000 + compressed_size`, which does not get relocated during the
kernel's boot process.
The kernel typically decompresses the image starting at address
0x1000000 (note: there's one more zero there than the compressed image
above). This usually is fine for most kernels.
However, if the compressed image is actually quite large, then
setup_data will live at a `0x100000 + compressed_size` that extends into
the decompressed zone at 0x1000000. In other words, if compressed_size
is larger than `0x1000000 - 0x100000`, then the decompression step will
clobber setup_data, resulting in crashes.
Visually, what happens now is that QEMU appends setup_data to the kernel
image:
kernel image setup_data
|--------------------------||----------------|
0x100000 0x100000+l1 0x100000+l1+l2
The problem is that this decompresses to 0x1000000 (one more zero). So
if l1 is > (0x1000000-0x100000), then this winds up looking like:
kernel image setup_data
|--------------------------||----------------|
0x100000 0x100000+l1 0x100000+l1+l2
d e c o m p r e s s e d k e r n e l
|-------------------------------------------------------------|
0x1000000 0x1000000+l3
The decompressed kernel seemingly overwriting the compressed kernel
image isn't a problem, because that gets relocated to a higher address
early on in the boot process, at the end of startup_64. setup_data,
however, stays in the same place, since those links are self referential
and nothing fixes them up. So the decompressed kernel clobbers it.
Fix this by appending setup_data to the cmdline blob rather than the
kernel image blob, which remains at a lower address that won't get
clobbered.
This could have been done by overwriting the initrd blob instead, but
that poses big difficulties, such as no longer being able to use memory
mapped files for initrd, hurting performance, and, more importantly, the
initrd address calculation is hard coded in qboot, and it always grows
down rather than up, which means lots of brittle semantics would have to
be changed around, incurring more complexity. In contrast, using cmdline
is simple and doesn't interfere with anything.
The microvm machine has a gross hack where it fiddles with fw_cfg data
after the fact. So this hack is updated to account for this appending,
by reserving some bytes.
Fixup-by: Michael S. Tsirkin <mst@redhat.com>
Cc: x86@kernel.org
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20221230220725.618763-1-Jason@zx2c4.com>
Message-ID: <20230128061015-mutt-send-email-mst@kernel.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Eric Biggers <ebiggers@google.com>
Tested-by: Mathias Krause <minipli@grsecurity.net>
It seems not super clear on when iova_tree is used, and why. Add a rich
comment above iova_tree to track why we needed the iova_tree, and when we
need it.
Also comment for the map/unmap messages, on how they're used and
implications (e.g. unmap can be larger than the mapped ranges).
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230109193727.1360190-1-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixup the migration compatibility for existing machine types
so that they do not enable msi-x.
Symptom:
(qemu) qemu: get_pci_config_device: Bad config data: i=0x34 read: 84 device: 98 cmask: ff wmask: 0 w1cmask:0
qemu: Failed to load PCIDevice:config
qemu: Failed to load virtio-rng:virtio
qemu: error while loading state for instance 0x0 of device '0000:00:03.0/virtio-rng'
qemu: load of migration failed: Invalid argument
Note: This fix will break migration from 7.2->7.2-fixed with this patch
bz: https://bugzilla.redhat.com/show_bug.cgi?id=2155749
Fixes: 9ea02e8f1 ("virtio-rng-pci: Allow setting nvectors, so we can use MSI-X")
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20230109105809.163975-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Daney <david.daney@fungible.com>
Fixes: 9ea02e8f1 ("virtio-rng-pci: Allow setting nvectors, so we can use MSI-X")<br>
Signed-off-by: Dr. David Alan Gilbert <<a href="mailto:dgilbert@redhat.com" target="_blank">dgilbert@redhat.com</a>><br>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Pressing attention button has special meaning when power indicator is
blinking. Better just not do it.
For example, trying to remove device immediately after hotplug leads to
both commands succeded but device not actually unrealized.
Same thing for PCIE hotplug was done in
81124b3c7a "pcie: add power indicator blink check"
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221116214458.82090-1-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This test is failing in gtk-vnc on Darwin:
$ make check-qtest-aarch64
...
19/20 qemu:qtest+qtest-aarch64 / qtest-aarch64/vnc-display-test
ERROR **: 10:42:35.488: vnc-error: Unsupported auth type 17973672
While QEMU picks the sigaltstack coroutine backend, gtk-vnc uses
the ucontext coroutine backend, which might be broken on Darwin.
Disable this test (current problem being investigated in this thread:
https://lore.kernel.org/qemu-devel/Y8kw6X6keB5l53nl@redhat.com/).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230119120514.28778-4-philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If we don't specify any machine, an architecture default
might be picked. But some architectures don't provide any
default, such ARM:
$ make check-qtest-aarch64
...
19/20 qemu:qtest+qtest-aarch64 / qtest-aarch64/vnc-display-test
qemu-system-aarch64: No machine specified, and there is no default
Since we don't need any particular machine to run this VNC
test, use the 'none' machine.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230119120514.28778-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
While this test is skipped on Windows, we still get when building:
tests/qtest/vnc-display-test.c:22:20: warning: unused function 'on_vnc_error' [-Wunused-function]
static inline void on_vnc_error(VncConnection* self,
^
tests/qtest/vnc-display-test.c:28:20: warning: unused function 'on_vnc_auth_failure' [-Wunused-function]
static inline void on_vnc_auth_failure(VncConnection *self,
^
2 warnings generated.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230119120514.28778-2-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since commit efc6c070ac ("configure: Add a test for the minimum
compiler version") the minimum compiler version required for GCC
is 4.8, which supports __builtin_bswap().
Remove the NetBSD specific ifdef'ry.
This reverts commit 1360677cfe
("makes NetBSD use the native bswap functions").
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230111163147.71761-7-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since commit efc6c070ac ("configure: Add a test for the minimum
compiler version") the minimum compiler version required for GCC
is 4.8, which supports __builtin_bswap().
Remove the FreeBSD specific ifdef'ry.
This reverts commit de03c3164a
("bswap: Fix build on FreeBSD 10.0").
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230111163147.71761-6-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since commit efc6c070ac ("configure: Add a test for the minimum
compiler version") the minimum compiler version required for GCC
is 4.8, which supports __builtin_bswap().
Remove the Haiku specific ifdef'ry.
This reverts commit 652a46ebba
("bswap.h: Include <endian.h> on Haiku for bswap operations").
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230111163147.71761-5-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
No need to recompile the dtc submodule here again and again, we can
use the pre-built binary from the distribution instead.
(And this will also help in case we finally get rid of the dtc submodule
in QEMU one day)
Message-Id: <20230124143824.844040-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Each job uses its own addons section nowadays, so the generic section
is completely unused and outdated, thus we can remove it now.
Message-Id: <20230119135914.2040853-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
No need to compile-test third party submodules over and over again if
we can simply use the pre-build library from the distribution instead.
By also adding --enable-fdt=system to the configure options, we can
also avoid to check out the "dtc" submodule here.
Message-Id: <20230120075330.2076773-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qemu-system-nios2 uses the functions from libfdt in hw/nios2/boot.c,
so this target has to be marked with TARGET_NEED_FDT=y in its config
file.
Message-Id: <20230119125745.2028814-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
'-drive if=none' is meant for configuring back-end devices only, so this
got marked as deprecated in QEMU 6.2. Users should now only use the new
way with '-drive if=pflash' instead.
Message-Id: <20230112083921.887828-1-thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are facing the issues that our test logs in the gitlab CI are
too big (and thus cut off). The bios-tables-test is one of the few
qtests that prints many lines of output by default when running with
V=1, so it contributes to this problem. Almost all other qtests are
silent with V=1 and only print debug messages with V=2 and higher.
Thus let's change the bios-tables-test to behave more like the
other tests and only print the debug messages with V=2 (or higher).
Message-Id: <20230118125132.1694469-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are still facing the issues that our test logs in the gitlab CI
are too big (and thus cut off). A huge part is still caused by the
qom-test that prints the path and name of each object it looks at
by default. That's too much. Let's be silent by default, and only
print the object path+name when running with V=2 (and the properties
only with V=3 and higher).
Message-Id: <20230118122557.1668860-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
On macOS, private $TMPDIR's are the default. These $TMPDIR's are
generated from a user's unix UID and UUID [1], which can create a
relatively long path:
/var/folders/d7/rz20f6hd709c1ty8f6_6y_z40000gn/T/
QEMU's avocado tests create a temporary directory prefixed by
"avo_qemu_sock_", and create QMP sockets within _that_ as well.
The QMP socket is unnecessarily long, because a temporary directory
is created for every QEMUMachine object.
/avo_qemu_sock_uh3w_dgc/qemu-37331-10bacf110-monitor.sock
The path limit for unix sockets on macOS is 104: [2]
/*
* [XSI] Definitions for UNIX IPC domain.
*/
struct sockaddr_un {
unsigned char sun_len; /* sockaddr len including null */
sa_family_t sun_family; /* [XSI] AF_UNIX */
char sun_path[104]; /* [XSI] path name (gag) */
};
This results in avocado tests failing on macOS because the QMP unix
socket can't be created, because the path is too long:
ERROR| Failed to establish connection: OSError: AF_UNIX path too long
This change resolves by reducing the size of the socket directory prefix
and the suffix on the QMP and console socket names.
The result is paths like this:
pdel@pdel-mbp:/var/folders/d7/rz20f6hd709c1ty8f6_6y_z40000gn/T
$ tree qemu*
qemu_df4evjeq
qemu_jbxel3gy
qemu_ml9s_gg7
qemu_oc7h7f3u
qemu_oqb1yf97
├── 10a004050.con
└── 10a004050.qmp
[1] https://apple.stackexchange.com/questions/353832/why-is-mac-osx-temp-directory-in-weird-path
[2] /Library/Developer/CommandLineTools/SDKs/MacOSX12.3.sdk/usr/include/sys/un.h
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230110082930.42129-2-peter@pjd.dev
Signed-off-by: John Snow <jsnow@redhat.com>
I've spent much time trying to debug hanging pipeline in gitlab. I
started from and idea that I have problem in code in my series (which
has some timeouts). Finally I found that the problem is that I've used
QEMUMachine class directly to avoid qtest, and didn't add necessary
arguments. Qemu fails and we wait for qmp accept endlessly. In gitlab
it's just stopped by timeout (one hour) with no sign of what's going
wrong.
With timeout enabled, gitlab don't wait for an hour and prints all
needed information.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-Id: <20220624195252.175249-1-vsementsov@yandex-team.ru>
[Fixed typing. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
blk_unref() can't report any errors that happen while closing the image.
For example, if qcow2 hits an -ENOSPC error while writing out dirty
bitmaps when it's closed, it prints error messages to stderr, but
'qemu-img bitmap' won't see any error return value and will therefore
look successful with exit code 0.
In order to fix this, manually inactivate the image first before calling
blk_unref(). This already performs the operations that would be most
likely to fail while closing the image, but it can still return errors.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1330
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230112191454.169353-4-kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
blk_unref() can't report any errors that happen while closing the image.
For example, if qcow2 hits an -ENOSPC error while writing out dirty
bitmaps when it's closed, it prints error messages to stderr, but
'qemu-img commit' won't see any error return value and will therefore
look successful with exit code 0.
In order to fix this, manually inactivate the image first before calling
blk_unref(). This already performs the operations that would be most
likely to fail while closing the image, but it can still return errors.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230112191454.169353-3-kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to write the bitmap table to the image file, it is converted to
big endian. If the write fails, it is passed to clear_bitmap_table() to
free all of the clusters it had allocated before. However, if we don't
convert it back to native endianness first, we'll free things at a wrong
offset.
In practical terms, the offsets will be so high that we won't actually
free any allocated clusters, but just run into an error, but in theory
this can cause image corruption.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230112191454.169353-2-kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add more annotations to functions, describing valid and invalid
calls from coroutine to non-coroutine context.
When applied to a function, no_coroutine_fn advertises that it should
not be called from coroutine_fn functions. This can be because the
function blocks or, in the case of generated_co_wrapper, to enforce
that coroutine_fn functions directly call the coroutine_fn that backs
the generated_co_wrapper.
coroutine_mixed_fn instead is for function that can be called in
both coroutine and non-coroutine context, but will suspend when
called in coroutine context. Annotating them is a first step
towards enforcing that non-annotated functions are absolutely
not going to suspend.
These can be used for example with the vrc tool:
# find functions that *really* cannot be called from no_coroutine_fn
(vrc) load --loader clang libblock.fa.p/meson-generated_.._block_block-gen.c.o
(vrc) paths [no_coroutine_fn,!coroutine_mixed_fn]
bdrv_remove_persistent_dirty_bitmap
bdrv_create
bdrv_can_store_new_dirty_bitmap
# find how coroutine_fns end up calling a mixed function
(vrc) load --loader clang --force libblock.fa.p/*.c.o
(vrc) paths [coroutine_fn] [!no_coroutine_fn]* [coroutine_mixed_fn]
...
bdrv_pread <- vhdx_log_write <- vhdx_log_write_and_flush <- vhdx_co_writev
...
Signed-off-by: Alberto Faria <afaria@redhat.com>
[Rebase, add coroutine_mixed_fn. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221216110758.559947-3-pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Clang has a generic __annotate__ attribute that can be used by
static analyzers to understand properties of functions and
analyze the control flow. Furthermore, unlike TSA annotations, the
__annotate__ attribute applies to function pointers as well.
As a first step towards static analysis of coroutine_fn markers,
attach the attribute to the marker when compiling with clang.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221216110758.559947-2-pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently we fill the VIRT_FLASH memory space with two 64MB NOR images
when using persistent UEFI variables on virt board. Actually we only use
a very small(non-zero) part of the memory while the rest significant
large(zero) part of memory is wasted.
So this patch checks the block status and only writes the non-zero part
into memory. This requires pflash devices to use sparse files for
backends.
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
[ kraxel: rebased to latest master ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20221220084246.1984871-1-kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In downstream RHEL builds, we do not have "blkverify" enabled, so
iotest 262 is currently failing there. Thus let's list "blkverify"
as required item so that the test properly gets skipped instead if
"blkverify" is missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230104112850.261480-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
"quorum" is required by iotest 312 - if it is not compiled into the
QEMU binary, the test fails. Thus list "quorum" as required driver
so that the test gets skipped in case it is not available.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230104114601.269351-1-thuth@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The old implementation replaces two insns, swapping between
b <dest>
nop
and
pcaddu18i tmp, <dest>
jirl zero, tmp, <dest> & 0xffff
There is a race condition in which a thread could be stopped at
the jirl, i.e. with the top of the address loaded, and when
restarted we have re-linked to a different TB, so that the top
half no longer matches the bottom half.
Note that while we never directly re-link to a different TB, we
can link, unlink, and link again all while the stopped thread
remains stopped.
The new implementation replaces only one insn, swapping between
b <dest>
and
pcadd tmp, <jmp_addr>
falling through to load the address from tmp, and branch.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Take the w^x split into account when computing the
pc-relative distance to an absolute pointer.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out a helper function, tcg_out_setcond_int, which
does not always produce the complete boolean result, but
returns a set of flags to do so.
Accept all int32_t as constant input, so that LE/GT can
adjust the constant to LT.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Adjust the constraints to allow any int32_t for immediate
addition. Split immediate adds into addu16i + addi, which
covers quite a lot of the immediate space. For the hole in
the middle, load the constant into TMP0 instead.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Regenerate with ADDU16I included:
$ cd loongarch-opcodes/scripts/go
$ go run ./genqemutcgdefs > $QEMU/tcg/loongarch64/tcg-insn-defs.c.inc
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Print both the raw field and the resolved pc-relative
address, as we do for branches.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While jirl shares the same instruction format as bne etc,
it is not assembled the same. In particular, rd is printed
first not second and the immediate is not pc-relative.
Decode into the arg_rr_i structure, which prints correctly.
This changes the "offs" member to "imm", to update translate.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reuse the decodetree based disassembler from
target/loongarch/ for tcg/loongarch64/.
The generation of decode-insns.c.inc into ./libcommon.fa.p/ could
eventually result in conflict, if any other host requires the same
trick, but this is good enough for now.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Although we still can't use ldrd and strd for all operations,
increase the chances by getting the register allocation correct.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have a test for one of TCG_TARGET_HAS_mulu2_i32 or
TCG_TARGET_HAS_muluh_i32 being defined, but the test
became non-functional when we changed to always define
all of these macros.
Replace this with a build-time test in tcg_gen_mulu2_i32.
Fixes: 25c4d9cc84 ("tcg: Always define all of the TCGOpcode enum members.")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1435
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
After recent header file inclusion rework the build fails when the blkio
module is enabled:
../block/blkio.c: In function ‘blkio_detach_aio_context’:
../block/blkio.c:321:24: error: implicit declaration of function ‘bdrv_get_aio_context’; did you mean ‘qemu_get_aio_context’? [-Werror=implicit-function-declaration]
321 | aio_set_fd_handler(bdrv_get_aio_context(bs),
| ^~~~~~~~~~~~~~~~~~~~
| qemu_get_aio_context
../block/blkio.c:321:24: error: nested extern declaration of ‘bdrv_get_aio_context’ [-Werror=nested-externs]
../block/blkio.c:321:24: error: passing argument 1 of ‘aio_set_fd_handler’ makes pointer from integer without a cast [-Werror=int-conversion]
321 | aio_set_fd_handler(bdrv_get_aio_context(bs),
| ^~~~~~~~~~~~~~~~~~~~~~~~
| |
| int
In file included from /home/pipo/git/qemu.git/include/qemu/job.h:33,
from /home/pipo/git/qemu.git/include/block/blockjob.h:30,
from /home/pipo/git/qemu.git/include/block/block_int-global-state.h:28,
from /home/pipo/git/qemu.git/include/block/block_int.h:27,
from ../block/blkio.c:13:
/home/pipo/git/qemu.git/include/block/aio.h:476:37: note: expected ‘AioContext *’ but argument is of type ‘int’
476 | void aio_set_fd_handler(AioContext *ctx,
| ~~~~~~~~~~~~^~~
../block/blkio.c: In function ‘blkio_file_open’:
../block/blkio.c:821:34: error: passing argument 2 of ‘blkio_attach_aio_context’ makes pointer from integer without a cast [-Werror=int-conversion]
821 | blkio_attach_aio_context(bs, bdrv_get_aio_context(bs));
| ^~~~~~~~~~~~~~~~~~~~~~~~
| |
| int
Fix it by including 'block/block-io.h' which contains the required
declarations.
Fixes: e2c1c34f13
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 2bc956011404a1ab03342aefde0087b5b4762562.1674477350.git.pkrempa@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio_blk_dma_restart_cb() is tricky because the BH must deal with
virtio_blk_data_plane_start()/virtio_blk_data_plane_stop() being called.
There are two issues with the code:
1. virtio_blk_realize() should use qdev_add_vm_change_state_handler()
instead of qemu_add_vm_change_state_handler(). This ensures the
ordering with virtio_init()'s vm change state handler that calls
virtio_blk_data_plane_start()/virtio_blk_data_plane_stop() is
well-defined. Then blk's AioContext is guaranteed to be up-to-date in
virtio_blk_dma_restart_cb() and it's no longer necessary to have a
special case for virtio_blk_data_plane_start().
2. Only blk_drain() waits for virtio_blk_dma_restart_cb()'s
blk_inc_in_flight() to be decremented. The bdrv_drain() family of
functions do not wait for BlockBackend's in_flight counter to reach
zero. virtio_blk_data_plane_stop() relies on blk_set_aio_context()'s
implicit drain, but that's a bdrv_drain() and not a blk_drain().
Note that virtio_blk_reset() already correctly relies on blk_drain().
If virtio_blk_data_plane_stop() switches to blk_drain() then we can
properly wait for pending virtio_blk_dma_restart_bh() calls.
Once these issues are taken care of the code becomes simpler. This
change is in preparation for multiple IOThreads in virtio-blk where we
need to clean up the multi-threading behavior.
I ran the reproducer from commit 49b44549ac ("virtio-blk: On restart,
process queued requests in the proper context") to check that there is
no regression.
Cc: Sergio Lopez <slp@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-id: 20221102182337.252202-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When we measure FIO read performance (cache=writethrough, bs=4k,
iodepth=64) in VMs, ~80K/s notifications (e.g., EPT_MISCONFIG) are observed
from guest to qemu.
It turns out those frequent notificatons are caused by interference from
worker threads. Worker threads queue bottom halves after completing IO
requests. Pending bottom halves may lead to either aio_compute_timeout()
zeros timeout and pass it to try_poll_mode() or run_poll_handlers() returns
no progress after noticing pending aio_notify() events. Both cause
run_poll_handlers() to call poll_set_started(false) to disable poll mode.
However, for both cases, as timeout is already zeroed, the event loop
(i.e., aio_poll()) just processes bottom halves and then starts the next
event loop iteration. So, disabling poll mode has no value but leads to
unnecessary notifications from guest.
To minimize unnecessary notifications from guest, defer disabling poll
mode to when the event loop is about to be blocked.
With this patch applied, FIO seq-read performance (bs=4k, iodepth=64,
cache=writethrough) in VMs increases from 330K/s to 413K/s IOPS.
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Chao Gao <chao.gao@intel.com>
Message-id: 20220710120849.63086-1-chao.gao@intel.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Do not encode the pointer as a constant in the opcode stream.
This pointer is specific to the cpu that first generated the
translation, which runs into problems with both hot-pluggable
cpus and user-only threads, as cpus are removed. It's also a
potential correctness issue in the theoretical case of a
slightly-heterogenous system, because if CPU 0 generates a
TB and then CPU 1 executes it, CPU 1 will end up using CPU 0's
hash table, which might have a wrong set of registers in it.
(All our current systems are either completely homogenous,
M-profile, or have CPUs sufficiently different that they
wouldn't be sharing TBs anyway because the differences would
show up in the TB flags, so the correctness issue is only
theoretical, not practical.)
Perform the lookup in either helper_access_check_cp_reg,
or a new helper_lookup_cp_reg.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230106194451.1213153-3-richard.henderson@linaro.org
[PMM: added note in commit message about correctness issue]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Qemu doesn't implement Debug Communication Channel, as well as the rest
of external debug interface. However, Microsoft Hyper-V in tries to
access some of those registers during an EL2 context switch.
Since there is no architectural way to not advertise support for external
debug, provide RAZ/WI stubs for OSDTRRX_EL1, OSDTRTX_EL1 and OSECCR_EL1
registers in the same way the rest of DCM is currently done. Do account
for access traps though with access_tda.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230120155929.32384-3-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In v7m_exception_taken(), for v8M we set the EXC_RETURN.ES bit if
either the exception targets Secure or if the CPU doesn't implement
the Security Extension. This is incorrect: the v8M Arm ARM specifies
that the ES bit should be RES0 if the Security Extension is not
implemented, and the pseudocode agrees.
Remove the incorrect condition, so that we leave the ES bit 0
if the Security Extension isn't implemented.
This doesn't have any guest-visible effects for our current set of
emulated CPUs, because all our v8M CPUs implement the Security
Extension; but it's worth fixing in case we add a v8M CPU without
the extension in future.
Reported-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
BASEPRI, FAULTMASK, and their _NS equivalents only exist on devices with
the Main Extension. However, the MRS instruction did not check this,
and the MSR instruction handled it inconsistently (warning BASEPRI, but
silently ignoring writes to BASEPRI_NS). Unify this behavior and always
warn when reading or writing any of these registers if the extension is
not present.
Signed-off-by: David Reiss <dreiss@meta.com>
Message-id: 167330628518.10497.13100425787268927786-0@git.sr.ht
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Second RISC-V PR for QEMU 8.0
* riscv_htif: Support console output via proxy syscall
* Cleanup firmware and device tree loading
* Fix elen check when using vector extensions
* add RISC-V OpenSBI boot test
* Ensure we always follow MISA parsing
* Fix up masking of vsip/vsie accesses
* Trap on writes to stimecmp from VS when hvictl.VTI=1
* Introduce helper_set_rounding_mode_chkfrm
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmPKRP0ACgkQIeENKd+X
# cFTHTwgAkyRDxrLepvI0KNaT0+cUBh+3QFlJ5JRtVnDW+5R+3aGT72PTS7Migqoh
# H3IFCB2mcSdQvyjj2jDFlrFd0oVIaqE0+bnhouS/4nHB5S/vmapHi4Mc74Vv1CMB
# rgXScL+C5gDOH1I7XjqOb1FY5Vxqyhi3IzdIoj+0ysUrGmUkqx+ij/cfQL7jkH9Q
# slNAkorgwgrTgMgkJ5RKd4cjyv35O4XKLAsgixVTfJ+WcxKmc/zaJOkNM/UDnmxK
# k2+2P8bshZWtWscXbm3oMC5+2ow1QtFedEkhHqb4adkQIyolKL7P1TfMlCgMSvES
# BKl0DUhqQ+7F77tik3GPy9spQ6LpTQ==
# =ifFF
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 20 Jan 2023 07:38:37 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* tag 'pull-riscv-to-apply-20230120' of https://github.com/alistair23/qemu: (37 commits)
hw/riscv/virt.c: move create_fw_cfg() back to virt_machine_init()
target/riscv: Remove helper_set_rod_rounding_mode
target/riscv: Introduce helper_set_rounding_mode_chkfrm
tcg/riscv: Use tcg_pcrel_diff in tcg_out_ldst
target/riscv: Trap on writes to stimecmp from VS when hvictl.VTI=1
target/riscv: Fix up masking of vsip/vsie accesses
hw/riscv: use ms->fdt in riscv_socket_fdt_write_distance_matrix()
hw/riscv: use MachineState::fdt in riscv_socket_fdt_write_id()
hw/riscv/virt.c: remove 'is_32_bit' param from create_fdt_socket_cpus()
hw/riscv/sifive_u.c: simplify create_fdt()
hw/riscv/virt.c: simplify create_fdt()
hw/riscv/spike.c: simplify create_fdt()
target/riscv: Use TARGET_FMT_lx for env->mhartid
target/riscv/cpu.c: do not skip misa logic in riscv_cpu_realize()
target/riscv/cpu: set cpu->cfg in register_cpu_props()
hw/riscv/boot.c: use MachineState in riscv_load_kernel()
hw/riscv/boot.c: use MachineState in riscv_load_initrd()
hw/riscv: write bootargs 'chosen' FDT after riscv_load_kernel()
hw/riscv: write initrd 'chosen' FDT inside riscv_load_initrd()
hw/riscv/spike.c: load initrd right after riscv_load_kernel()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip are defined
in pnv.h. Many users of the header don't actually need them. One
instance is this inclusion loop: hw/ppc/pnv_homer.h includes
hw/ppc/pnv.h for typedef PnvChip, and vice versa for struct PnvHomer.
Similar structs live in their own headers: PnvHomerClass and PnvHomer
in pnv_homer.h, PnvLpcClass and PnvLpcController in pci_lpc.h,
PnvPsiClass, PnvPsi, Pnv8Psi, Pnv9Psi, Pnv10Psi in pnv_psi.h, ...
Move PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip to new
pnv_chip.h, and adjust include directives. This breaks the inclusion
loop mentioned above.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221222104628.659681-2-armbru@redhat.com>
We have two inclusion loops:
block/block.h
-> block/block-global-state.h
-> block/block-common.h
-> block/blockjob.h
-> block/block.h
block/block.h
-> block/block-io.h
-> block/block-common.h
-> block/blockjob.h
-> block/block.h
I believe these go back to Emanuele's reorganization of the block API,
merged a few months ago in commit d7e2fe4aac.
Fortunately, breaking them is merely a matter of deleting unnecessary
includes from headers, and adding them back in places where they are
now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221221133551.3967339-2-armbru@redhat.com>
qemu/coroutine.h and qemu/lockable.h include each other.
They need each other only in macro expansions, so we could simply drop
both inclusions to break the loop, and add suitable includes to files
that expand the macros.
Instead, move a part of qemu/coroutine.h to new qemu/coroutine-core.h
so that qemu/coroutine-core.h doesn't need qemu/lockable.h, and
qemu/lockable.h only needs qemu/coroutine-core.h. Result:
qemu/coroutine.h includes qemu/lockable.h includes
qemu/coroutine-core.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221221131435.3851212-5-armbru@redhat.com>
[Semantic rebase conflict with 7c10cb38cc "accel/tcg: Add debuginfo
support" resolved]
Commit 1c20d3ff60 ("hw/riscv: virt: Add a machine done notifier")
moved the initialization of fw_cfg to the virt_machine_done() callback.
Problem is that the validation of fw_cfg by devices such as ramfb is
done before the machine done notifier is called. Moving create_fw_cfg()
to machine_done() results in QEMU failing to boot when using a ramfb
device:
./qemu-system-riscv64 -machine virt -device ramfb -serial stdio
qemu-system-riscv64: -device ramfb: ramfb device requires fw_cfg with DMA
The fix is simple: move create_fw_cfg() config back to
virt_machine_init(). This happens to be the same way the ARM 'virt'
machine deals with fw_cfg (see machvirt_init() and virt_machine_done()
in hw/arm/virt.c), so we're keeping consistency with how other machines
handle this device.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1343
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230117132751.229738-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current logic attempts to shift the VS-level bits into their correct
position in mip while leaving the remaining bits in-tact. This is both
pointless and likely incorrect since one would expect that any new, future
VS-level interrupts will get their own position in mip rather than sharing
with their (H)S-level equivalent. Fix this, and make the logic more
readable, by just making off the VS-level bits and shifting them into
position.
This also fixes reads of vsip, which would only ever report vsip.VSSIP
since the non-writable bits got masked off as well.
Fixes: d028ac7512 ("arget/riscv: Implement AIA CSRs for 64 local interrupts on RV32")
Signed-off-by: Andrew Bresticker <abrestic@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221215224541.1423431-1-abrestic@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
create_fdt_socket_cpus() writes a different 'mmu-type' value if we're
running in 32 or 64 bits. However, the flag is being calculated during
virt_machine_init(), and is passed around in create_fdt(), then
create_fdt_socket(), and then finally create_fdt_socket_cpus(). None of
the intermediate functions are using the flag, which is a bit
misleading.
Remove 'is_32_bit' flag from create_fdt_socket_cpus() and calculate it
using the already available RISCVVirtState pointer. This will also
change the signature of create_fdt_socket() and create_fdt(), making it
clear that these functions don't do anything special when we're running
in 32 bit mode.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230111170948.316276-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
All RISCV CPUs are setting cpu->cfg during their cpu_init() functions,
meaning that there's no reason to skip all the misa validation and setup
if misa_ext was set beforehand - especially since we're setting an
updated value in set_misa() in the end.
Put this code chunk into a new riscv_cpu_validate_set_extensions()
helper and always execute it regardless of what the board set in
env->misa_ext.
This will put more responsibility in how each board is going to init
their attributes and extensions if they're not using the defaults.
It'll also allow realize() to do its job looking only at the extensions
enabled per se, not corner cases that some CPUs might have, and we won't
have to change multiple code paths to fix or change how extensions work.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20230113175230.473975-3-dbarboza@ventanamicro.com>
[ Changes by AF:
- Rebase
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is an informal contract between the cpu_init() functions and
riscv_cpu_realize(): if cpu->env.misa_ext is zero, assume that the
default settings were loaded via register_cpu_props() and do validations
to set env.misa_ext. If it's not zero, skip this whole process and
assume that the board somehow did everything.
At this moment, all SiFive CPUs are setting a non-zero misa_ext during
their cpu_init() and skipping a good chunk of riscv_cpu_realize(). This
causes problems when the code being skipped in riscv_cpu_realize()
contains fixes or assumptions that affects all CPUs, meaning that SiFive
CPUs are missing out.
To allow this code to not be skipped anymore, all the cpu->cfg.ext_*
attributes needs to be set during cpu_init() time. At this moment this
is being done in register_cpu_props(). The SiFive boards are setting
their own extensions during cpu_init() though, meaning that they don't
want all the defaults from register_cpu_props().
Let's move the contract between *_cpu_init() and riscv_cpu_realize() to
register_cpu_props(). Inside this function we'll check if
cpu->env.misa_ext was set and, if that's the case, set all relevant
cpu->cfg.ext_* attributes, and only that. Leave the 'misa_ext' = 0 case
as is today, i.e. loading all the defaults from riscv_cpu_extensions[].
register_cpu_props() can then be called by all the cpu_init() functions,
including the SiFive ones. This will make all CPUs behave more in line
with what riscv_cpu_realize() expects.
This will also make the cpu_init() functions even more alike, but at this
moment we would need some design changes in how we're initializing
extensions/attributes (e.g. some CPUs are setting cfg options after
register_cpu_props(), so we can't simply add the function to a common
post_init() hook) to make a common cpu_init() code across all CPUs.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230113175230.473975-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The sifive_u, spike and virt machines are writing the 'bootargs' FDT
node during their respective create_fdt().
Given that bootargs is written only when '-append' is used, and this
option is only allowed with the '-kernel' option, which in turn is
already being check before executing riscv_load_kernel(), write
'bootargs' in the same code path as riscv_load_kernel().
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230102115241.25733-8-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
riscv_load_initrd() returns the initrd end addr while also writing a
'start' var to mark the addr start. These informations are being used
just to write the initrd FDT node. Every existing caller of
riscv_load_initrd() is writing the FDT in the same manner.
We can simplify things by writing the FDT inside riscv_load_initrd(),
sparing callers from having to manage start/end addrs to write the FDT
themselves.
An 'if (fdt)' check is already inserted at the end of the function
because we'll end up using it later on with other boards that doesn´t
have a FDT.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230102115241.25733-7-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
riscv_load_firmware(), riscv_load_initrd() and riscv_load_kernel() works
under the assumption that a 'filename' parameter is always not NULL.
This is currently the case since all callers of these functions are
checking for NULL before calling them. Add an g_assert() to make sure
that a NULL value in these cases are to be considered a bug.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230102115241.25733-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present create_fdt() calls htif_uses_elf_symbols() to determine
whether to insert a <reg> property for the HTIF. This unfortunately
creates a hidden dependency to riscv_load_{firmware,kernel} that
create_fdt() must be called after the ELF {firmware,kernel} image
has been loaded.
Decouple such dependency be adding a new parameter to create_fdt(),
whether custom HTIF base address is used. The flag will be set if
non ELF {firmware,kernel} image is given by user.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20221229091828.1945072-13-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Rename previous riscv_find_firmware() to riscv_find_bios(), and
introduce a new riscv_find_firmware() to implement the first half
part of the work done in riscv_find_and_load_firmware().
This new API is helpful for machine that wants to know the final
chosen firmware file name but does not want to load it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-12-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some boards are duplicating the 'riscv_find_and_load_firmware' call
because the 32 and 64 bits images have different names. Create
a function to handle this detail instead of hardcoding it in the boards.
Ideally we would bake this logic inside riscv_find_and_load_firmware(),
or even create a riscv_load_default_firmware(), but at this moment we
cannot infer whether the machine is running 32 or 64 bits without
accessing RISCVHartArrayState, which in turn can't be accessed via the
common code from boot.c. In the end we would exchange 'firmware_name'
for a flag with riscv_is_32bit(), which isn't much better than what we
already have today.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221221182300.307900-6-dbarboza@ventanamicro.com>
Message-Id: <20221229091828.1945072-11-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the HTIF proxy syscall is unsupported. On RV32, only
device 0 is supported so there is no console device for RV32.
The only way to implement console funtionality on RV32 is to
support the SYS_WRITE syscall.
With this commit, the Spike machine is able to boot the 32-bit
OpenSBI generic image.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Monitor patches for 2023-01-19
# -----BEGIN PGP SIGNATURE-----
#
# iQJGBAABCAAwFiEENUvIs9frKmtoZ05fOHC0AOuRhlMFAmPJO+8SHGFybWJydUBy
# ZWRoYXQuY29tAAoJEDhwtADrkYZTbBwP/RsZLLDCz6moSet4Hly+vPTWibyYYDkS
# uk6a70Ja7fsAcONumBaXdpoinPtbED662eYxidbLFr//tAjnKu57jnwAIFTTOKJc
# sCVtdgOlbNSZFrqyIr8ctY6yKJLLBaa02in/BczFIQphPatpUwvxrvrdgxc58NNK
# qaeKDnWKXvZ6EUaYPpruxqE5J/NV0ykyab9Rc8rNJqdUMnqbd662zHcA0l31misH
# gAfKBhReo53XUbfvoFS9kaoBQaTJPk4CcKHaT7NJXR8ezlIEQVLtFzdfAf04kSdG
# 8VRwwx5NDpmafATEaMXJhJ74Fyc8biDWXoQ6aA1jdUCu39B2EPl1H1qlCG9ZYp7w
# CkbJU6UwtOYsG11NU8Mr1u9rMlAgAVkkLsMYiiI4cpLBkI0vkoV66ms3oZgYUtbq
# /TgCpfjKpE87ZBLIwJjGsg+TMN2AH5lpt/49HV8QEFA8mI7h29oo2HvheXE7PPzH
# b9iIe9ADrKwB5DpJW2vigPj+fSHqoSGd3R/hUcMVOubKnJme97mys2hD+sfxga/H
# qfKLzgTqQI2dGhfow/8wzfYdfYmkii+ggDyzcxLAxx2ITO/fLWJygmTgXJmA3dl6
# pnpZvhOu4dEgK4VstugXcvgCVHUVXd9wqI9wxJAc+mKanTmZIJBnxCm/QVG2/w/d
# 5IgmP9Se7vb0
# =7OEC
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 19 Jan 2023 12:47:43 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-monitor-2023-01-19' of https://repo.or.cz/qemu/armbru:
ui: Simplify control flow in qemu_mouse_set()
ui: Split hmp_mouse_set() and move the HMP part to ui/
ui: Don't check for mode change after mouse_set error
ui: Reduce nesting in hmp_change_vnc() slightly
ui: Factor out hmp_change_vnc(), and move to ui/ui-hmp-cmds.c
ui: Improve "change vnc" error reporting
ui: Move HMP commands from monitor to new ui/ui-hmp-cmds.c
ui: Factor out qmp_add_client() parts and move to ui/ui-qmp-cmds.c
ui: Move QMP commands from monitor to new ui/ui-qmp-cmds.c
ui: Clean up a few things checkpatch.pl would flag later on
ui/spice: Give hmp_info_spice()'s channel_names[] static linkage
ui/spice: QXLInterface method set_mm_time() is now dead, drop
ui/spice: Require spice-server >= 0.14.0
Revert "hmp: info spice: take out webdav"
ui/spice: Require spice-protocol >= 0.14.0
ui: Fix silent truncation of numeric keys in HMP sendkey
ui: Check numeric part of expire_password argument @time properly
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch from monitor_printf() to error_setg() and hmp_handle_error().
This makes "this is an error" more obvious both in the source and in
the monitor, where hmp_handle_error() prefixes the message with
"Error: ".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109190321.1056914-13-armbru@redhat.com>
This moves these commands from MAINTAINERS section "QMP" to
"Graphics".
Command add-client applies to socket character devices in addition to
display devices. Move it anyway. Aside: the way @protocol character
device IDs and display types is bad design.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109190321.1056914-10-armbru@redhat.com>
Version 0.14.0 is now old enough to have made it into the major
distributions:
Debian 11: 0.14.3
RHEL-8: 0.14.3
FreeBSD (ports): 0.15.0
Fedora 35: 0.15.0
Ubuntu 20.04: 0.14.2
OpenSUSE Leap 15.3: 0.14.3
Requiring it lets us drop a number of version checks. The next commit
will clean up some more.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230109190321.1056914-6-armbru@redhat.com>
Version 0.14.0 is now old enough to have made it into the major
distributions:
Debian 11: 0.14.3
RHEL-8: 0.14.2
FreeBSD (ports): 0.14.4
Fedora 35: 0.14.0
Ubuntu 20.04: 0.14.0
OpenSUSE Leap 15.3: 0.14.3
Requiring it lets us drop two version checks in ui/vdagent.c. It also
enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230109190321.1056914-4-armbru@redhat.com>
When argument @time isn't 'now' or 'never', we parse it as an integer,
optionally prefixed with '+'. If parsing fails, we silently assume
zero. Report an error and fail instead.
While there, use qemu_strtou64() instead of strtoull() so
checkpatch.pl won't complain.
Aside: encoding numbers in strings is bad QMP practice.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230109190321.1056914-2-armbru@redhat.com>
block/block-hmp-cmds.h and qemu/co-shared-resource.h use coroutine_fn
without including qemu/coroutine.h. They compile only if it's already
included from elsewhere.
I could fix that, but pulling in qemu/coroutine.h and everything it
includes just for a macro that expands into nothing feels silly.
Instead, move the macro to qemu/osdep.h.
Inclusions of qemu/coroutine.h just for coroutine_fn become
superfluous. Drop them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221221131435.3851212-3-armbru@redhat.com>
When a protected VM is started with the maximum number of CPUs (248),
the service call providing information on the CPUs requires more
buffer space than allocated and QEMU disgracefully aborts :
LOADPARM=[........]
Using virtio-blk.
Using SCSI scheme.
...................................................................................
qemu-system-s390x: KVM_S390_MEM_OP failed: Argument list too long
When protected virtualization is initialized, compute the maximum
number of vCPUs supported by the machine and return useful information
to the user before the machine starts in case of error.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20230116174607.2459498-2-clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The old Haiku VM based on Beta 3 does not work anymore since it
fails to install the additional packages now that Beta 4 has been
released. Thanks to Alexander von Gluck IV for providing a new
image based on Beta 4, we can now upgrade the test image in our
QEMU CI, too, to get this working again.
Note that Haiku Beta 4 apparently finally fixed the issue with
the enumeration of the virtio-block devices (see the ticket at
https://dev.haiku-os.org/ticket/16512 ) - the tarball disk can
now be found at index 1 instead of index 0.
Message-Id: <20230116083014.55647-1-thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The register definitions in tests/qtest/libqos/e1000e.h had names
different from hw/net/e1000_regs.h, which made it hard to understand
what test codes corresponds to the implementation. Use
hw/net/e1000_regs.h from tests/qtest/libqos/e1000e.c to remove
these duplications.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230114035919.35251-20-akihiko.odaki@daynix.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When sending mail to Kamil's address, it's bouncing with a message
that the mailbox is full. This already happens since summer 2022,
and the last message that Kamil sent to the qemu-devel mailing list
is from November 2021 (as far as I can see), so we unfortunately
have to assume that this e-mail address is not valid anymore.
Message-Id: <20230113081735.1148057-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Meson supports an "uninstall", so we can easily allow it to work by
not suppressing the forwarding of it from Make to meson.
We originally suppressed this because Meson's 'uninstall' has a hole
in it: it will remove everything that is installed by a mechanism
meson knows about, but not things installed by "custom install
scripts", and there is no "custom uninstall script" mechanism.
For QEMU, though, the only thing that was being installed by a custom
install script was the LC_MESSAGES files handled by Meson's i18n
module, and that code was fixed in Meson commit 487d45c1e5bfff0fbdb4,
which is present in Meson 0.60.0 and later. Since we already require
a Meson version newer than that, we're now safe to enable
'uninstall', as it will now correctly uninstall everything that was
installed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/109
Message-Id: <20230110151250.24434-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Now that tcg can handle direct and indirect goto_tb simultaneously,
we can optimistically leave space for a direct branch and fall back
to loading the pointer from the TB for an indirect branch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that tcg can handle direct and indirect goto_tb
simultaneously, we can optimistically leave space for
a direct branch and fall back to loading the pointer
from the TB for an indirect branch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The old sparc64 implementation may replace two insns, which leaves
a race condition in which a thread could be stopped at a PC in the
middle of the sequence, and when restarted does not see the complete
address computation and branches to nowhere.
The new implemetation replaces only one insn, swapping between a
direct branch and a direct call. The TCG_REG_TB register is loaded
from tb->jmp_target_addr[] in the delay slot.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The old ppc64 implementation replaces 2 or 4 insns, which leaves a race
condition in which a thread could be stopped at a PC in the middle of
the sequence, and when restarted does not see the complete address
computation and branches to nowhere.
The new implemetation replaces only one insn, swapping between
b <dest>
and
mtctr r31
falling through to a general-case indirect branch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The old implementation replaces two insns, swapping between
b <dest>
nop
br x30
and
adrp x30, <dest>
addi x30, x30, lo12:<dest>
br x30
There is a race condition in which a thread could be stopped at
the PC of the second insn, and when restarted does not see the
complete address computation and branches to nowhere.
The new implemetation replaces only one insn, swapping between
b <dest>
br tmp
and
ldr tmp, <jmp_addr>
br tmp
Reported-by: hev <r@hev.cc>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We now have the option to generate direct or indirect
goto_tb depending on the dynamic displacement, thus
the define is no longer necessary or completely accurate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Stop overloading jmp_target_arg for both offset and address,
depending on TCG_TARGET_HAS_direct_jump. Instead, add a new
field to hold the jump insn offset and always set the target
address in jmp_target_addr[]. This will allow a tcg backend
to use either direct or indirect depending on displacement.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This can replace four other variables that are references
into the TranslationBlock structure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The INDEX_op_goto_tb opcode needs no register allocation.
Split out a dedicated helper function for it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Similar to the existing set_jmp_reset_offset. Include the
rw->rx address space conversion done by arm and s390x, and
forgotten by mips and riscv.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Similar to the existing set_jmp_reset_offset. Move any assert for
TCG_TARGET_HAS_direct_jump into the new function (which now cannot
be build-time). Will be unused if TCG_TARGET_HAS_direct_jump is
constant 0, but we can't test for constant in the preprocessor,
so just mark it G_GNUC_UNUSED.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The INDEX_op_exit_tb opcode needs no register allocation.
Split out a dedicated helper function for it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Merge tpm 2023/01/17 v1
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmPGjawACgkQda1lgCoL
# QhHOgQf/QxWxhydyj2679bnznCgJXOXKQ1C+MkFvk0ekPJT+bZDwKoohAH3JgbxT
# zp3UeMmtqS9JQDcGF6PdIldp4DB7uH+InvVkFFZeD1LN0X6nYHEgZ3Q1obSbf8ut
# TGlB6+4TM6ehtk9owDuzlm7/5OFLmEGvGjdVgzZKtwzXGWUKVO7AzzRQBj4QnKq/
# w8cSlZAlF+lJI3IsnCh8EIAdL3SP8dub3yfYJDepbht7IwfkUWPOWBFOSUpo5quX
# r1rLKWtjQRsoGDe4iRNrLQu+sgj9npZwj7aYotarJauYBW8qd3jdD4OtiBYj2OMU
# LvEIqwNyITivKnapEnDEJV74umzArw==
# =lIgU
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 17 Jan 2023 11:59:40 GMT
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* tag 'pull-tpm-2023-01-17-1' of https://github.com/stefanberger/qemu-tpm:
tests/qtest/tpm-emu: Avoid hangs using abort handlers closing channels
tests/qtest: Poll on waitpid() for a while before sending SIGKILL
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Install abort handlers that close the TPM control and data channels in
case an abort occurs. The purpose of this is to have QEMU terminate
under abnormal test case failures to resolve intermittent hangs on s390x
hosts running TPM tests for QEMU/x86_64.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20230111134547.3959604-1-stefanb@linux.ibm.com
To prevent getting stuck on waitpid() in case the target process does
not terminate on SIGTERM, poll on waitpid() for 30s and if the target
process has not changed state until then send a SIGKILL to it.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20230112143413.3979057-1-stefanb@linux.ibm.com
[PMM: changed TFR to RETRY_ON_EINTR]
Recently the g_assert(cpu == current_cpu) test has been
intermittently failing with gcc. Reorg the code around
the setjmp to minimize the lifetime of the cpu variable
affected by the setjmp.
This appears to fix the existing issue with clang as well.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1147
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use the attribute, which is supported by clang, instead of
the #pragma, which is not supported and, for some reason,
also not detected by the meson probe, so we fail by -Werror.
Include only <immintrin.h> as that is the outermost "official"
header for these intrinsics -- emmintrin.h and smmintrin -- are
older SSE2 and SSE4 specific headers, while the immintrin.h
includes all of the Intel intrinsics.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add ability to dump /tmp/perf-<pid>.map and jit-<pid>.dump.
The first one allows the perf tool to map samples to each individual
translation block. The second one adds the ability to resolve symbol
names, line numbers and inspect JITed code.
Example of use:
perf record qemu-x86_64 -perfmap ./a.out
perf report
or
perf record -k 1 qemu-x86_64 -jitdump ./a.out
DEBUGINFOD_URLS= perf inject -j -i perf.data -o perf.data.jitted
perf report -i perf.data.jitted
Co-developed-by: Vanderson M. do Rosario <vandersonmr2@gmail.com>
Co-developed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230112152013.125680-4-iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add libdw-based functions for loading and querying debuginfo. Load
debuginfo from the system and the linux-user loaders.
This is useful for the upcoming perf support, which can then put
human-readable guest symbols instead of raw guest PCs into perfmap and
jitdump files.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230112152013.125680-3-iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When exiting due to an exit() syscall, qemu-user calls
preexit_cleanup(), but this is currently not the case when exiting due
to a signal. This leads to various buffers not being flushed (e.g.,
for gprof, for gcov, and for the upcoming perf support).
Add the missing call.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112152013.125680-2-iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Guest driver might execute HW commands when shared buffers are not yet
allocated.
This could happen on purpose (malicious guest) or because of some other
guest/host address mapping error.
We need to protect againts such case.
Fixes: CVE-2022-1050
Reported-by: Raven <wxhusst@gmail.com>
Signed-off-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Message-Id: <20220403095234.2210-1-yuval.shaia.ml@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
../hw/usb/ccid-card-emulated.c: In function 'handle_apdu_thread':
../hw/usb/ccid-card-emulated.c:251:24: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
251 | assert((unsigned long)event > 1000);
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230103110814.3726795-2-marcandre.lureau@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Running the test-hmp with V=2 up to V=9 runs the test in verbose mode,
but running for example with V=10 falls back to non-verbose mode ...
Improve this oddity by properly treating the argument as a number.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109101306.271444-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Seems like there is also nothing target-specific in here, so these
files can be moved to softmmu_ss to avoid that they get compiled
twice (once for qemu-system-arm and once for qemu-system-aarch64).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112134928.1026006-7-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We're still running into the problem that some logs are cut in the
gitlab-CI since they got too big. The biggest part of the log is
still the output of the qom-test. Let's stop printing the properties
by default to get to a saner size here. The full output can still
be enabled by setting V=2 (or higher) in the environment.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221215153036.422362-1-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MIPS patches queue
A bunch of cleanups from various people.
- Improved GT64120 on big-endian hosts
- GT64120 north bridge and MC146818 RTC devices are now target independent
- Bonito64 north bridge converted to 3-phase reset API
- PCI refactors around PIIX devices
- Support for nanoMIPS in bootloader generator API
- New YAMON Malta Avocado test
- Removal of 'trap and emulate' KVM support
- System-specific QMP commands restricted to system emulation
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmPBekAACgkQ4+MsLN6t
# wN4wjxAAtYxyt6WUBpiYfV/LnbQFpAsacues1Vhy9MPYEg5a/iuXWKvWtgRYvGww
# qR0GVQH8rH7tgnCZK+ioq9jX+hvfBskP6CnKhxmb5zDGm7vP7jhhu8UFWY/EtBgq
# 0zpNeLMXtnRJ6PBqo/nWFCVtcpDRZ6IkSbpGWkVkciRFc5n/2VCnlIj8k2I1oMvL
# 11cp2xFQnaPReFXIpMjJHuHv1NObykdlvVg6wQo/A/4qIb8EvJQEPmePjG9Sf0i0
# v2dhnnxG9mze7+uq0dIC16x8Azko3N7dmtNlBU/aGb9OELwx35aux2M4dNDVogwn
# DqL/Wsk54TFewECOfS48t/a/TqV8j/ISW1d/JvovBrN2KovmIAbtqHuMUqKVk5l0
# 23ZOIIPIYwmScZwIlkCIGUuIzFig1zhEmQcoEQaFe/B0oLB2eN/x0Bk9Yklo+i2A
# WNiyiAj7k5492qEdndOySEEDVt6886F/+CdQ6QYF5Z1L/ELck7XHBH3mGDznWpPn
# 6IURyVquPJx7ul62jSGI+Gc+qakNoahIhPo5O7hklOM9GwWNOWXHveyb7xjs7j+O
# eWyVcet+o7hoHkCzmfbyTPySI4qCpF9fA42jqPhATwQPwmGXpbr+4BxUq3KtE43y
# w9tEigwd4voN3dWLItVh6QE4in70osz3XHp93byvo8bHlS0huVY=
# =oXX+
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 13 Jan 2023 15:35:28 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'mips-20230113' of https://github.com/philmd/qemu: (46 commits)
scripts/git.orderfile: Display MAINTAINERS changes first
target/mips: Restrict 'qapi-commands-machine.h' to system emulation
hw/mips/boston: Rename MachineState 'mc' pointer to 'ms'
hw/pci-host/bonito: Declare TYPE_BONITO_PCI_HOST_BRIDGE in header
hw/pci-host/bonito: Use 'bonito_pci' for PCI function #0 code
hw/pci-host/bonito: Use 'bonito_host' for PCI host bridge code
hw/pci-host/bonito: Convert to 3-phase reset
softmmu/rtc: Emit warning when using driftfix=slew on systems without mc146818
hw/rtc/mc146818rtc: Make the mc146818 RTC device target independent
hw/core/qdev-properties-system: Allow the 'slew' policy only on x86
hw/intc: Extract the IRQ counting functions into a separate file
hw/intc/i8259: Make using the isa_pic singleton more type-safe
hw/usb/hcd-uhci: Introduce TYPE_ defines for device models
hw/mips/Kconfig: Track Malta's PIIX dependencies via Kconfig
hw/isa/piix4: Decouple INTx-to-LNKx routing which is board-specific
hw/isa/piix3: Decouple INTx-to-LNKx routing which is board-specific
hw/pci/pci: Factor out pci_bus_map_irqs() from pci_bus_irqs()
hw/pci/pci_host: Trace config accesses on unexisting functions
mips: Always include nanomips disassembler
mips: Remove support for trap and emulate KVM
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit a0e61807a3 ("qapi: Remove QMP events and commands from
user-mode builds") we don't generate the "qapi-commands-machine.h"
header in a user-emulation-only build.
Extract the QMP functions from cpu.c (which is always compiled) to
the new 'sysemu/mips-qmp-cmds.c' unit (which is only compiled when
system emulation is selected).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221219211034.70491-4-philmd@linaro.org>
The 'slew' lost tick policy is only available on systems with a mc146818
RTC. On other systems, "-rtc driftfix=slew" is currently silently ignored.
Let's emit at least a warning in this case to make the users aware that
there is something wrong in their command line settings.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230110095351.611724-5-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The only reason for this code being target dependent was the IRQ-counting
related code in rtc_policy_slew_deliver_irq(). Since these functions have
been moved into a new, separate file (kvm_irqcount.c) which is now always
compiled and linked if necessary, we can get rid of the #ifdef TARGET_I386
switches in mc146818rtc.c and declare it in the softmmu_ss instead of
specific_ss, so that the code only gets compiled once for all targets.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230110095351.611724-4-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The 'slew' tick policy is currently enforced to be only available on
x86 via some "#ifdef TARGET_I386" statements in mc146818rtc.c. We
want to get rid of those #ifdefs, so we need a different way of
checking whether the policy is allowed or not. Using the setter
function in hw/core/qdev-properties-system.c seems to be a good
place, so let's add a check here.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230110095351.611724-3-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
These IRQ counting functions will soon be required in binaries that
do not include the APIC code, too, so let's extract them into a
separate file that can be linked independently of the APIC code.
While we're at it, change the apic_* prefix into kvm_* since the
functions are used from the i8259 PIC (i.e. not the APIC), too.
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230110095351.611724-2-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_map_irq_fn's in general seem to be board-specific, and PIIX4's
pci_slot_get_pirq() in particular seems very Malta-specific. So move the
latter to malta.c to 1/ keep the board logic in one place and 2/ avoid
PIIX4 to make assumptions about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_map_irq_fn's in general seem to be board-specific. So move PIIX3's
pci_slot_get_pirq() to board code to not have PIIX3 make assuptions
about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_bus_irqs() coupled together the assignment of pci_set_irq_fn and
pci_map_irq_fn to a PCI bus. This coupling gets in the way when the
pci_map_irq_fn is board-specific while the pci_set_irq_fn is device-
specific.
For example, both of QEMU's PIIX south bridge models have different
pci_map_irq_fn implementations which are board-specific rather than
device-specific. These implementations should therefore reside in board
code. The pci_set_irq_fn's, however, should stay in the device models
because they access memory internal to the model.
Factoring out pci_bus_map_irqs() from pci_bus_irqs() allows the
assignments to be decoupled, resolving the problem described above.
Note also how pci_vpb_realize() which gets touched in this commit
assigns different pci_map_irq_fn's depending on the board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-5-shentey@gmail.com>
[PMD: Factor out in vfu_object_set_bus_irq()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
target-arm queue:
hw/arm/stm32f405: correctly describe the memory layout
hw/arm: Add Olimex H405 board
cubieboard: Support booting from an SD card image with u-boot on it
target/arm: Fix sve_probe_page
target/arm: allow writes to SCR_EL3.HXEn bit when FEAT_HCX is enabled
various code cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmPBZmYZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3rDdD/9GlrH14yP/2WQZJVJxzXkf
# ltO1pvX/AfeNPGy3F8T+kncKspIUeJ8BQNrZKYPWkH1WgAAT3lVH/cUbAlr8UD6W
# p2t64ZdQAURuEw3kqtyUVOUeIxzg29cEQyW/9uchA3QPb9xDtiq6KLpAzifDzo6o
# 2JE4/NytUJSKxFr5hnyxRTtOYPEMLShBSPvPzU0/BPq7VPyPhT4rqojhpx9uZpVc
# h4mfVm9cpF0y3ThBR37M0nhEGJywB/6zOsZ49bm06MFFTwasZ4P0w0fcKhbvrFvX
# PHVlNOvyT1oxch5ErN+KULZLByiWy0/Nw85V8P9R+1hU6nncQPM5paB6Y5HUCTKv
# wa9gp38V8323fsHg2EEV/PYRdcmRWSBHOq9HPDjIIJlG9nvfXn9O69kDlhnst44b
# Fz27XiGJOKY+f20l0J0KzaOnnjw54aeo5tc5WUDbBiZ/btsAHBGQAg7JghmoLkhb
# rlvJFgGdG99IuBqJH69dJQ8n/R9bGDRu6X0i1ir3d3C2nY9HYaWUZMyyxOw9dV43
# igQHupOzyYbSyy9+40xz611P0h2k2d90P61Vi41D9ig4Du+I4Vftjqj9mi/Z829k
# W1JE5wpKWcDeIXFYLWCZuiOyTCCFBWiWgDJz/zQf7AYma0AWA9gpKrTh2+3EFfqy
# VsvMR2T6kmS3FId50bW5OQ==
# =D+ib
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 13 Jan 2023 14:10:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230113' of https://git.linaro.org/people/pmaydell/qemu-arm: (38 commits)
target/arm: allow writes to SCR_EL3.HXEn bit when FEAT_HCX is enabled
hw/timer/xilinx_timer: Use XpsTimerState instead of 'struct timerblock'
hw/intc/xilinx_intc: Use 'XpsIntc' typedef instead of 'struct xlx_pic'
hw/misc/sbsa_ec: Declare QOM macros using OBJECT_DECLARE_SIMPLE_TYPE()
hw/misc/sbsa_ec: Rename TYPE_SBSA_EC -> TYPE_SBSA_SECURE_EC
hw/arm/npcm7xx: Declare QOM macros using OBJECT_DECLARE_SIMPLE_TYPE()
hw/arm/bcm2836: Remove definitions generated by OBJECT_DECLARE_TYPE()
hw/arm/stellaris: Use CamelCase for STELLARIS_ADC type name
hw/arm/stellaris: Drop useless casts from void * to pointer
hw/intc/omap_intc: Use CamelCase for TYPE_OMAP_INTC type name
hw/gpio/omap_gpio: Use CamelCase for TYPE_OMAP2_GPIO type name
hw/gpio/omap_gpio: Use CamelCase for TYPE_OMAP1_GPIO type name
hw/arm/omap: Drop useless casts from void * to pointer
hw/gpio/omap_gpio: Add local variable to avoid embedded cast
hw/arm/pxa: Avoid forward-declaring PXA2xxI2CState
hw/arm: Remove unreachable code calling pflash_cfi01_register()
hw/arm/vexpress: Remove dead code in vexpress_common_init()
hw/arm/z2: Use the IEC binary prefix definitions
hw/arm/omap_sx1: Use the IEC binary prefix definitions
hw/arm/omap_sx1: Remove unused 'total_ram' definitions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM trusted firmware, when built with FEAT_HCX support, sets SCR_EL3.HXEn bit
to allow EL2 to modify HCRX_EL2 register without trapping it in EL3. Qemu
uses a valid mask to clear unsupported SCR_EL3 bits when emulating SCR_EL3
write, and that mask doesn't include SCR_EL3.HXEn bit even if FEAT_HCX is
enabled and exposed to the guest. As a result EL3 writes of that bit are
ignored.
Cc: qemu-stable@nongnu.org
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Message-id: 20230105221251.17896-4-eiakovlev@linux.microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IRQRC[A:D] registers reset value is 0x80. We were forcing
the MIPS Malta machine routing to be able to boot a Linux
kernel without any bootloader.
We now have these registers initialized in the Malta machine
write_bootloader(), so we can use the correct reset values.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-4-philmd@linaro.org>
Linux kernel expects the northbridge & southbridge chipsets
configured by the BIOS firmware. We emulate that by writing
a tiny bootloader code in write_bootloader().
Upon introduction in commit 5c2b87e34d ("PIIX4 support"),
the PIIX4 configuration space included values specific to
the Malta board.
Set the Malta-specific IRQ routing values in the embedded
bootloader, so the next commit can remove the Malta specific
bits from the PIIX4 PCI-ISA bridge and make it generic
(matching the real hardware).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-3-philmd@linaro.org>
Similarly to how commit 0c8427baf0 ("hw/mips/malta: Use bootloader
helper to set BAR registers") converted write_bootloader(), convert
the equivalent write_bootloader_nanomips(), allowing us to modify
the bootloader code more easily in the future.
Part 1/5: Convert PCI0 MEM1 BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-7-philmd@linaro.org>
The single machine using this device explicitly sets its
endianness. We don't need to set a default. This allow us
to remove the target specificity from the build system.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20221209151533.69516-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
GT64120's PCI endianness swapping works on little-endian hosts,
but doesn't on big-endian ones. Instead of complicating how
CFGADDR/CFGDATA registers deal with endianness, use the existing
MemoryRegionOps from hw/pci/pci_host.c. Doing so also reduce the
access to internal PCI_HOST_BRIDGE fields.
Map the PCI_HOST_BRIDGE MemoryRegionOps into the corresponding
CFGADDR/CFGDATA regions in the ISD MMIO and remove the unused
code in the current ISD read/write handlers.
Update the mapping when PCI0_CMD register is accessed (in case
the endianness is changed).
This allows using the GT64120 on a big-endian host (and boot
the MIPS Malta machine in little-endian).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-6-philmd@linaro.org>
Single registers access in ISD can produce multiple changes
in the address spaces. To reduce computational effort,
accumulate these as a single memory transaction.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-5-philmd@linaro.org>
The FPGA LEDs/ASCII display is mostly used by the bootloader
to show very low-level debug info. QEMU connects its output
to a character device backend, which is not very practical
to correlate with ASM instruction executed, interrupts or
MMIO accesses. Also, the display discard the previous states.
To ease bootloader debugging experience, add a pair of trace
events. Such events can be analyzed over time or diff-ed
between different runs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-4-philmd@linaro.org>
This remove a use of 'struct' in the DECLARE_INSTANCE_CHECKER()
macro call, to avoid after a QOM refactor:
hw/timer/xilinx_timer.c:65:1: error: declaration of anonymous struct must be a definition
DECLARE_INSTANCE_CHECKER(struct timerblock, XILINX_TIMER,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230109140306.23161-15-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This remove a use of 'struct' in the DECLARE_INSTANCE_CHECKER()
macro call, to avoid after a QOM refactor:
hw/intc/xilinx_intc.c:45:1: error: declaration of anonymous struct must be a definition
DECLARE_INSTANCE_CHECKER(struct xlx_pic, XILINX_INTC,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230109140306.23161-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The typedef and definitions are generated by the OBJECT_DECLARE_TYPE
macro in "hw/arm/bcm2836.h":
20 #define TYPE_BCM283X "bcm283x"
21 OBJECT_DECLARE_TYPE(BCM283XState, BCM283XClass, BCM283X)
The script ran in commit a489d1951c ("Use OBJECT_DECLARE_TYPE when
possible") missed them because they are declared in a different
file unit. Remove them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Upon introduction in commit b8433303fb ("Set proper device-width
for vexpress flash"), ve_pflash_cfi01_register() was calling
qdev_init_nofail() which can not fail. This call was later
converted with a script to use &error_fatal, still unable to
fail. Remove the unreachable code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109115316.2235-13-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Allwinner TWI/I2C controller emulation. Only
master-mode functionality is implemented.
The SPL boot for Cubieboard expects AXP209 PMIC on TWI0/I2C0 bus, so this is
first part enabling the TWI/I2C bus operation.
Since both Allwinner A10 and H3 use the same module, it is added for
both boards.
Docs are also updated for Cubieboard and Orangepi-PC board to indicate
I2C availability.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several DRAM Controller registers are used. Most
important registers are those related to DRAM initialization and
calibration, where SPL initiates process and waits until certain bit is
set/cleared.
This patch adds these registers, initializes reset values from user's
guide and updates state of registers as SPL expects it.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cmd_line.txt mangling is only needed when rebuilding from very old
trees and is kept mostly as an example of how to extend it. However,
Meson 0.63 introduces a deprecation mechanism for meson_options.txt
that can be used instead, so get rid of our home-grown hack.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VRCPSS, VRSQRTSS and VCVTSx2Sx have a 32-bit or 64-bit memory operand,
which is represented in the decoding tables by X86_VEX_REPScalar. Add it
to the tables, and make validate_vex() handle the case of an instruction
that is in exception type 4 without the REP prefix and exception type 5
with it; this is the cas of VRCP and VRSQRT.
Reported-by: yongwoo <https://gitlab.com/yongwoo36>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1377
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the assignment is causing a compiler warning, fix it by using
memcpy instead.
CC libvduse.o
libvduse.c: In function ‘vring_set_avail_event’:
libvduse.c:603:7: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasin]
603 | *((uint16_t *)&vq->vring.used->ring[vq->vring.num]) = htole16(val);
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Suggested-by: Xie Yongji <xieyongji@bytedance.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <4a0fe2a6436464473119fdbf0bc4076b36fbb37f.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It seems there is no need to keep the inuse field signed and end up with
compiler warnings for sign-compare.
CC libvduse.o
libvduse.c: In function ‘vduse_queue_pop’:
libvduse.c:789:19: error: comparison of integer expressions of different signedness: ‘int’ and ‘unsigned int’ [-Werror=sign-compare]
789 | if (vq->inuse >= vq->vring.num) {
| ^~
Instead of casting the comparison to unsigned int, just make the inuse
field unsigned int in the fist place.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Message-Id: <9fe3fd8b042e048bd04d506ca6e43d738b5c45b7.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the libvduse sources are used by another project, it can not be
guaranteed that _GNU_SOURCE is set by the build system. If it is for
example not set, errors like this show up.
CC libvduse.o
libvduse.c: In function ‘vduse_log_get’:
libvduse.c:172:9: error: implicit declaration of function ‘ftruncate’; did you mean ‘strncat’? [-Werror=implicit-function-declaration]
172 | if (ftruncate(fd, size) == -1) {
| ^~~~~~~~~
| strncat
The simplest way to allow external complication of libvduse.[ch] by
setting _GNU_SOURCE if it is not already set by the build system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Message-Id: <407f3665f0605df936e5bfe60831d180edfb8cca.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The assignment of dev->postcopy_ufd can be moved into an else clause and
then the code becomes C90 compliant.
CC libvhost-user.o
libvhost-user.c: In function ‘vu_set_postcopy_advise’:
libvhost-user.c:1625:5: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
1625 | struct uffdio_api api_struct;
| ^~~~~~
Understandable, it might be desired to avoid else clauses, but in this
case it seems clear enough and frankly the dev->postcopy_ufd is only
assigned once.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <74db52afb1203c4580ffc7fa462b4b2ba260a353.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using libvhost-user source in an external project that wants to
comply with the C90 standard, it is best to declare variables before
code.
CC libvhost-user.o
libvhost-user.c: In function ‘generate_faults’:
libvhost-user.c:683:9: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
683 | struct uffdio_register reg_struct;
| ^~~~~~
In this case, it is also simple enough and doesn't cause any extra
ifdef additions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <556c2d00c01fa134d13c0371d4014c90694c2943.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The sign-compare warning also hits some of the for-loops, but it easy
fixed by just making the iterator variable unsigned int.
CC libvhost-user.o
libvhost-user.c: In function ‘vu_gpa_to_va’:
libvhost-user.c:223:19: error: comparison of integer expressions of different signedness: ‘int’ and ‘uint32_t’ {aka ‘unsigned int’} [-Werror=sign-compare]
223 | for (i = 0; i < dev->nregions; i++) {
| ^
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Message-Id: <decb925e1a6fb9538738d2570bda2804f888fa15.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The assert from recvmsg() return value against an uint32_t size field
from a protocol struct throws a compiler warning.
CC libvhost-user.o
In file included from libvhost-user.c:27:
libvhost-user.c: In function ‘vu_message_read_default’:
libvhost-user.c:363:19: error: comparison of integer expressions of different signedness: ‘int’ and ‘uint32_t’ {aka ‘unsigned int’} [-Werror=sign-compare]
363 | assert(rc == vmsg->size);
| ^~
This is not critical, but annoying when the libvhost-user source are
used in an external project that has this compiler warning switched on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Message-Id: <7a791e27b7bd3e0a8b8cc8fbb15090a870d226d5.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Strictly speaking only -std=gnu99 support the usage of typeof and for
easier inclusion in external projects, it is better to use __typeof__.
CC libvhost-user.o
libvhost-user.c: In function ‘vu_log_queue_fill’:
libvhost-user.c:86:13: error: implicit declaration of function ‘typeof’ [-Werror=implicit-function-declaration]
86 | typeof(x) _min1 = (x); \
| ^~~~~~
Changing these two users of typeof makes the compiler happy and no extra
flags or pragmas need to be provided.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <981aa822bcaaa2b8d74f245339a99a85c25b346f.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Then the libvhost-user sources are used by another project, it can not
be guaranteed that _GNU_SOURCE is set by the build system. If it is for
example not set, errors like this show up.
CC libvhost-user.o
libvhost-user.c: In function ‘vu_panic’:
libvhost-user.c:195:9: error: implicit declaration of function ‘vasprintf’; did you mean ‘vsprintf’? [-Werror=implicit-function-declaration]
195 | if (vasprintf(&buf, msg, ap) < 0) {
| ^~~~~~~~~
| vsprintf
The simplest way to allow external complication of libvhost-user.[ch] is
by setting _GNU_SOURCE if it is not already set by the build system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Message-Id: <be27dcc747a6b5cc6f8ae3f79e0b79171382bcef.1671741278.git.marcel@holtmann.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using --disable-virglrenderer, QEMU still creates
hw-display-virtio-gpu-gl.so
hw-display-virtio-vga-gl.so
hw-display-virtio-gpu-pci-gl.so
but when these are loaded, they provide no functionality as the code
which registers types is not compiled in. Funtionally this is
relatively harmless, because QEMU is fine loading a module with no
types.
This is rather confusing for users and OS distro maintainers though,
as they think they have the GL functionality built, but in fact the
module they are looking at provides nothing of value.
The root cause is the use of 'when/if_true' rules when adding sources
to the module source set. If all the rules evaluate to false, then we
have declared the module, but not added anything to it. We need to
put declaration of the entire module inside a condition based on
existance of the 3rd party library deps that are mandatory.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1352
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221219125830.2369169-1-berrange@redhat.com>
[Do not check for pixman. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We've been very gradually adding G_GNUC_PRINTF annotations
to functions over years. This has been useful in detecting
certain malformed printf strings, or cases where we pass
user data as the printf format which is a potential security
flaw.
Given the inherant memory corruption danger in use of format
strings vs mis-matched variadic arguments, it is worth applying
G_GNUC_PRINTF to all functions using printf, even if we know
they are safe.
The compilers can reasonably reliably identify such places
with the -Wsuggest-attribute=format / -Wmissing-format-attribute
flags.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221219130205.687815-7-berrange@redhat.com>
[-Wsuggest-attribute=format and -Wmissing-format-attribute are
synonyms, only include one; disable it for testfloat. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace HAVE_CHARDEV_PARPORT with a Meson conditional, remove unnecessary
defines, and close the file descriptor on FreeBSD/DragonFly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To avoid compilation errors when -Werror=maybe-uninitialized is used,
add a default case with g_assert_not_reached().
Otherwise with GCC 11.3.1 "cc (GCC) 11.3.1 20220421 (Red Hat 11.3.1-2)"
we get:
../target/i386/ops_sse.h: In function ‘helper_vpermdq_ymm’:
../target/i386/ops_sse.h:2495:13: error: ‘r3’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
2495 | d->Q(3) = r3;
| ~~~~~~~~^~~~
../target/i386/ops_sse.h:2494:13: error: ‘r2’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
2494 | d->Q(2) = r2;
| ~~~~~~~~^~~~
../target/i386/ops_sse.h:2493:13: error: ‘r1’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
2493 | d->Q(1) = r1;
| ~~~~~~~~^~~~
../target/i386/ops_sse.h:2492:13: error: ‘r0’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
2492 | d->Q(0) = r0;
| ~~~~~~~~^~~~
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20221222140158.1260748-1-eric.auger@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we update an existing memslot (e.g., resize, split), we temporarily
remove the memslot to re-add it immediately afterwards. These updates
are not atomic, especially not for KVM VCPU threads, such that we can
get spurious faults.
Let's inhibit most KVM ioctls while performing relevant updates, such
that we can perform the update just as if it would happen atomically
without additional kernel support.
We capture the add/del changes and apply them in the notifier commit
stage instead. There, we can check for overlaps and perform the ioctl
inhibiting only if really required (-> overlap).
To keep things simple we don't perform additional checks that wouldn't
actually result in an overlap -- such as !RAM memory regions in some
cases (see kvm_set_phys_mem()).
To minimize cache-line bouncing, use a separate indicator
(in_ioctl_lock) per CPU. Also, make sure to hold the kvm_slots_lock
while performing both actions (removing+re-adding).
We have to wait until all IOCTLs were exited and block new ones from
getting executed.
This approach cannot result in a deadlock as long as the inhibitor does
not hold any locks that might hinder an IOCTL from getting finished and
exited - something fairly unusual. The inhibitor will always hold the BQL.
AFAIKs, one possible candidate would be userfaultfd. If a page cannot be
placed (e.g., during postcopy), because we're waiting for a lock, or if the
userfaultfd thread cannot process a fault, because it is waiting for a
lock, there could be a deadlock. However, the BQL is not applicable here,
because any other guest memory access while holding the BQL would already
result in a deadlock.
Nothing else in the kernel should block forever and wait for userspace
intervention.
Note: pause_all_vcpus()/resume_all_vcpus() or
start_exclusive()/end_exclusive() cannot be used, as they either drop
the BQL or require to be called without the BQL - something inhibitors
cannot handle. We need a low-level locking mechanism that is
deadlock-free even when not releasing the BQL.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Tested-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20221111154758.1372674-4-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using the new accel-blocker API, mark where ioctls are being called
in KVM. Next, we will implement the critical section that will take
care of performing memslots modifications atomically, therefore
preventing any new ioctl from running and allowing the running ones
to finish.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20221111154758.1372674-3-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This API allows the accelerators to prevent vcpus from issuing
new ioctls while execting a critical section marked with the
accel_ioctl_inhibit_begin/end functions.
Note that all functions submitting ioctls must mark where the
ioctl is being called with accel_{cpu_}ioctl_begin/end().
This API requires the caller to always hold the BQL.
API documentation is in sysemu/accel-blocker.h
Internally, it uses a QemuLockCnt together with a per-CPU QemuLockCnt
(to minimize cache line bouncing) to keep avoid that new ioctls
run when the critical section starts, and a QemuEvent to wait
that all running ioctls finish.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221111154758.1372674-2-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When in 64-bit mode, IDT entiries are 16 bytes, so `intno * 16` is used
for base/limit/offset calculations. However, even in 64-bit mode, the
exception error code still uses bits [3,16) for the invlaid interrupt
index.
This means the error code should still be `intno * 8 + 2` even in 64-bit
mode.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1382
Signed-off-by: Joe Richey <joerichey@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the local Error variable with errp and ERRP_GUARD() and change
the return value to bool.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Remove an unnecessary local Error value in nvme_realize(). In the
process, change nvme_check_constraints() to return a bool.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* s390x header clean-ups from Philippe
* Rework and improvements of the EINTR handling by Nikita
* Deprecate the -no-hpet command line option
* Disable the qtests in the 32-bit Windows CI job again
* Some other misc fixes here and there
# gpg: Signature made Mon 09 Jan 2023 14:21:19 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-01-09' of https://gitlab.com/thuth/qemu:
.gitlab-ci.d/windows: Do not run the qtests in the msys2-32bit job
error handling: Use RETRY_ON_EINTR() macro where applicable
Refactoring: refactor TFR() macro to RETRY_ON_EINTR()
docs/interop: Change the vnc-ledstate-Pseudo-encoding doc into .rst
i386: Deprecate the -no-hpet QEMU command line option
tests/qtest/bios-tables-test: Replace -no-hpet with hpet=off machine parameter
tests/readconfig: spice doesn't support unix socket on windows yet
target/s390x: Restrict sysemu/reset.h to system emulation
target/s390x/tcg/excp_helper: Restrict system headers to sysemu
target/s390x/tcg/misc_helper: Remove unused "memory.h" include
hw/s390x/pv: Restrict Protected Virtualization to sysemu
exec/memory: Expose memory_region_access_valid()
MAINTAINERS: Add MIPS-related docs and configs to the MIPS architecture section
tests/vm: Update get_default_jobs() to work on non-x86_64 non-KVM hosts
qemu-iotests/stream-under-throttle: do not shutdown QEMU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qtests are not stable in the msys2-32bit job yet - especially
the test-hmp and the qom-test are failing randomly. Until this is
fixed, let's better disable the qtests here again to avoid failing
CI tests.
Message-Id: <20230105204819.26992-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are going to deprecate (and finally remove later) the -no-hpet command
line option. Prepare the bios-tables-test by using the replacement hpet=off
machine parameter instead.
Message-Id: <20230109081205.116369-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In user emulation, threads -- implemented as CPU -- are
created/destroyed, but never reset. There is no point in
allowing the user emulation access the sysemu/reset API.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221220145625.26392-5-philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
On non-x86_64 host, if KVM is not available we get:
Traceback (most recent call last):
File "tests/vm/basevm.py", line 634, in main
vm = vmcls(args, config=config)
File "tests/vm/basevm.py", line 104, in __init__
mem = max(4, args.jobs)
TypeError: '>' not supported between instances of 'NoneType' and 'int'
Fix by always returning a -- not ideal but safe -- '1' value.
Fixes: b09539444a ("tests/vm: allow us to take advantage of MTTCG")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221209164743.70836-1-philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
virtio,pc,pci: features, cleanups, fixes
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 08 Jan 2023 08:01:39 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (50 commits)
vhost-scsi: fix memleak of vsc->inflight
acpi: cpuhp: fix guest-visible maximum access size to the legacy reg block
tests: acpi: aarch64: Add *.topology tables
tests: acpi: aarch64: Add topology test for aarch64
tests: acpi: Add and whitelist *.topology blobs
tests: virt: Update expected ACPI tables for virt test
hw/acpi/aml-build: Only generate cluster node in PPTT when specified
tests: virt: Allow changes to PPTT test table
virtio-pci: fix proxy->vector_irqfd leak in virtio_pci_set_guest_notifiers
vdpa: commit all host notifier MRs in a single MR transaction
vhost: configure all host notifiers in a single MR transaction
vhost: simplify vhost_dev_enable_notifiers
vdpa: harden the error path if get_iova_range failed
vdpa-dev: get iova range explicitly
docs/devel: Rules on #include in headers
include: Include headers where needed
include/hw/virtio: Break inclusion loop
include/hw/cxl: Break inclusion loop cxl_pci.h and cxl_cdat_h
include/hw/pci: Include hw/pci/pci.h where needed
include/hw/pci: Split pci_device.h off pci.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prior to reading the shadow doorbell cq head, we have to update the
eventidx. Otherwise, we risk that the driver will skip an mmio doorbell
write. This happens on riscv64, as reported by Guenter.
Adding the missing update to the cq eventidx fixes the issue.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Cc: qemu-riscv@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Rename the trace events related to writing the event index and reading
the doorbell value to make it more clear that the event is associated
with an actual update (write or read respectively).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Replace various ->parent_obj use with the equivalent QOM accessors.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* Atomic memslot updates for KVM (Emanuele, David)
* Always send errors to logfile when daemonized (Greg)
* Add support for IDE CompactFlash card (Lubomir)
* First round of build system cleanups (myself)
* First round of feature removals (myself)
* Reduce "qemu/accel.h" inclusion (Philippe)
# gpg: Signature made Thu 05 Jan 2023 23:51:09 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (24 commits)
i386: SGX: remove deprecated member of SGXInfo
target/i386: Add SGX aex-notify and EDECCSSA support
util: remove support -chardev tty and -chardev parport
util: remove support for hex numbers with a scaling suffix
KVM: remove support for kernel-irqchip=off
docs: do not talk about past removal as happening in the future
meson: accept relative symlinks in "meson introspect --installed" data
meson: cleanup compiler detection
meson: support meson 0.64 -Doptimization=plain
configure: test all warnings
tests/qapi-schema: remove Meson workaround
meson: cleanup dummy-cpus.c rules
meson: tweak hardening options for Windows
configure: remove backwards-compatibility and obsolete options
configure: preserve qemu-ga variables
configure: cleanup $cpu tests
configure: remove dead function
configure: remove useless write_c_skeleton
ide: Add "ide-cf" driver, a CompactFlash card
ide: Add 8-bit data mode
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
tcg/s390x improvements:
- drop support for pre-z196 cpus (eol before 2017)
- add support for misc-instruction-extensions-3
- misc cleanups
# gpg: Signature made Sat 07 Jan 2023 07:47:59 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20230106' of https://gitlab.com/rth7680/qemu: (27 commits)
tcg/s390x: Avoid the constant pool in tcg_out_movi
tcg/s390x: Cleanup tcg_out_movi
tcg/s390x: Tighten constraints for 64-bit compare
tcg/s390x: Implement ctpop operation
tcg/s390x: Use tgen_movcond_int in tgen_clz
tcg/s390x: Support SELGR instruction in movcond
tcg/s390x: Generalize movcond implementation
tcg/s390x: Create tgen_cmp2 to simplify movcond
tcg/s390x: Support MIE3 logical operations
tcg/s390x: Tighten constraints for and_i64
tcg/s390x: Tighten constraints for or_i64 and xor_i64
tcg/s390x: Issue XILF directly for xor_i32
tcg/s390x: Support MIE2 MGRK instruction
tcg/s390x: Support MIE2 multiply single instructions
tcg/s390x: Distinguish RIE formats
tcg/s390x: Distinguish RRF-a and RRF-c formats
tcg/s390x: Use LARL+AGHI for odd addresses
tcg/s390x: Remove DISTINCT_OPERANDS facility check
tcg/s390x: Remove FAST_BCR_SER facility check
tcg/s390x: Check for load-on-condition facility at startup
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is below memleak detected when to quit the qemu-system-x86_64 (with
vhost-scsi-pci).
(qemu) quit
=================================================================
==15568==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0x7f00aec57917 in __interceptor_calloc (/lib64/libasan.so.6+0xb4917)
#1 0x7f00ada0d7b5 in g_malloc0 (/lib64/libglib-2.0.so.0+0x517b5)
#2 0x5648ffd38bac in vhost_scsi_start ../hw/scsi/vhost-scsi.c:92
#3 0x5648ffd38d52 in vhost_scsi_set_status ../hw/scsi/vhost-scsi.c:131
#4 0x5648ffda340e in virtio_set_status ../hw/virtio/virtio.c:2036
#5 0x5648ff8de281 in virtio_ioport_write ../hw/virtio/virtio-pci.c:431
#6 0x5648ff8deb29 in virtio_pci_config_write ../hw/virtio/virtio-pci.c:576
#7 0x5648ffe5c0c2 in memory_region_write_accessor ../softmmu/memory.c:493
#8 0x5648ffe5c424 in access_with_adjusted_size ../softmmu/memory.c:555
#9 0x5648ffe6428f in memory_region_dispatch_write ../softmmu/memory.c:1515
#10 0x5648ffe8613d in flatview_write_continue ../softmmu/physmem.c:2825
#11 0x5648ffe86490 in flatview_write ../softmmu/physmem.c:2867
#12 0x5648ffe86d9f in address_space_write ../softmmu/physmem.c:2963
#13 0x5648ffe86e57 in address_space_rw ../softmmu/physmem.c:2973
#14 0x5648fffbfb3d in kvm_handle_io ../accel/kvm/kvm-all.c:2639
#15 0x5648fffc0e0d in kvm_cpu_exec ../accel/kvm/kvm-all.c:2890
#16 0x5648fffc90a7 in kvm_vcpu_thread_fn ../accel/kvm/kvm-accel-ops.c:51
#17 0x56490042400a in qemu_thread_start ../util/qemu-thread-posix.c:505
#18 0x7f00ac3b6ea4 in start_thread (/lib64/libpthread.so.0+0x7ea4)
Free the vsc->inflight at the 'stop' path.
Fixes: b82526c7ee ("vhost-scsi: support inflight io track")
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Li Feng <fengli@smartx.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Message-Id: <20230104160433.21353-1-dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The modern ACPI CPU hotplug interface was introduced in the following
series (aa1dd39ca307..679dd1a957df), released in v2.7.0:
1 abd49bc2ed docs: update ACPI CPU hotplug spec with new protocol
2 16bcab97eb pc: piix4/ich9: add 'cpu-hotplug-legacy' property
3 5e1b5d9388 acpi: cpuhp: add CPU devices AML with _STA method
4 ac35f13ba8 pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
5 d2238cb678 acpi: cpuhp: implement hot-add parts of CPU hotplug
interface
6 8872c25a26 acpi: cpuhp: implement hot-remove parts of CPU hotplug
interface
7 76623d00ae acpi: cpuhp: add cpu._OST handling
8 679dd1a957 pc: use new CPU hotplug interface since 2.7 machine type
Before patch#1, "docs/specs/acpi_cpu_hotplug.txt" only specified 1-byte
accesses for the hotplug register block. Patch#1 preserved the same
restriction for the legacy register block, but:
- it specified DWORD accesses for some of the modern registers,
- in particular, the switch from the legacy block to the modern block
would require a DWORD write to the *legacy* block.
The latter functionality was then implemented in cpu_status_write()
[hw/acpi/cpu_hotplug.c], in patch#8.
Unfortunately, all DWORD accesses depended on a dormant bug: the one
introduced in earlier commit a014ed07bd ("memory: accept mismatching
sizes in memory_region_access_valid", 2013-05-29); first released in
v1.6.0. Due to commit a014ed07bd, the DWORD accesses to the *legacy*
CPU hotplug register block would work in spite of the above series *not*
relaxing "valid.max_access_size = 1" in "hw/acpi/cpu_hotplug.c":
> static const MemoryRegionOps AcpiCpuHotplug_ops = {
> .read = cpu_status_read,
> .write = cpu_status_write,
> .endianness = DEVICE_LITTLE_ENDIAN,
> .valid = {
> .min_access_size = 1,
> .max_access_size = 1,
> },
> };
Later, in commits e6d0c3ce68 ("acpi: cpuhp: introduce 'Command data 2'
field", 2020-01-22) and ae340aa3d2 ("acpi: cpuhp: spec: add typical
usecases", 2020-01-22), first released in v5.0.0, the modern CPU hotplug
interface (including the documentation) was extended with another DWORD
*read* access, namely to the "Command data 2" register, which would be
important for the guest to confirm whether it managed to switch the
register block from legacy to modern.
This functionality too silently depended on the bug from commit
a014ed07bd.
In commit 5d971f9e67 ('memory: Revert "memory: accept mismatching sizes
in memory_region_access_valid"', 2020-06-26), first released in v5.1.0,
the bug from commit a014ed07bd was fixed (the commit was reverted).
That swiftly exposed the bug in "AcpiCpuHotplug_ops", still present from
the v2.7.0 series quoted at the top -- namely the fact that
"valid.max_access_size = 1" didn't match what the guest was supposed to
do, according to the spec ("docs/specs/acpi_cpu_hotplug.txt").
The symptom is that the "modern interface negotiation protocol"
described in commit ae340aa3d2:
> + Use following steps to detect and enable modern CPU hotplug interface:
> + 1. Store 0x0 to the 'CPU selector' register,
> + attempting to switch to modern mode
> + 2. Store 0x0 to the 'CPU selector' register,
> + to ensure valid selector value
> + 3. Store 0x0 to the 'Command field' register,
> + 4. Read the 'Command data 2' register.
> + If read value is 0x0, the modern interface is enabled.
> + Otherwise legacy or no CPU hotplug interface available
falls apart for the guest: steps 1 and 2 are lost, because they are DWORD
writes; so no switching happens. Step 3 (a single-byte write) is not
lost, but it has no effect; see the condition in cpu_status_write() in
patch#8. And step 4 *misleads* the guest into thinking that the switch
worked: the DWORD read is lost again -- it returns zero to the guest
without ever reaching the device model, so the guest never learns the
switch didn't work.
This means that guest behavior centered on the "Command data 2" register
worked *only* in the v5.0.0 release; it got effectively regressed in
v5.1.0.
To make things *even more* complicated, the breakage was (and remains, as
of today) visible with TCG acceleration only. Commit 5d971f9e67 makes
no difference with KVM acceleration -- the DWORD accesses still work,
despite "valid.max_access_size = 1".
As commit 5d971f9e67 suggests, fix the problem by raising
"valid.max_access_size" to 4 -- the spec now clearly instructs the guest
to perform DWORD accesses to the legacy register block too, for enabling
(and verifying!) the modern block. In order to keep compatibility for the
device model implementation though, set "impl.max_access_size = 1", so
that wide accesses be split before they reach the legacy read/write
handlers, like they always have been on KVM, and like they were on TCG
before 5d971f9e67 (v5.1.0).
Tested with:
- OVMF IA32 + qemu-system-i386, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32X64 + qemu-system-x86_64, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32 + qemu-system-i386, SMM enabled, using TCG accel; verified the
register block switch and the present/possible CPU counting through the
modern hotplug interface, during OVMF boot (bugfix test);
- I do not have any testcase (guest payload) for regression-testing CPU
hotplug through the *legacy* CPU hotplug register block.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
Ref: "IO port write width clamping differs between TCG and KVM"
Link: http://mid.mail-archive.com/aaedee84-d3ed-a4f9-21e7-d221a28d1683@redhat.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2023-01/msg00199.html
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230105161804.82486-1-lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently we'll always generate a cluster node no matter user has
specified '-smp clusters=X' or not. Cluster is an optional level
and will participant the building of Linux scheduling domains and
only appears on a few platforms. It's unncessary to always build
it when it cannot reflect the real topology on platforms having no
cluster implementation and to avoid affecting the linux scheduling
domains in the VM. So only generate the cluster topology in ACPI
PPTT when the user has specified it explicitly in -smp.
Tested qemu-system-aarch64 with `-smp 8` and linux 6.1-rc1, without
this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
56 # cluster_id
with this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
36 # cluster_id, with no cluster node kernel will make it to
physical package id
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Message-Id: <20221229065513.55652-3-yangyicong@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the vhost-vdpa device to batch the setup of all its MRs of
host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on setup the host notifier MRs reduce from 423ms to 32ms for a VM with
64 vCPUs and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device).
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-4-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This allows the vhost device to batch the setup of all its host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on enabling notifiers reduce from 376ms to 9.1ms for a VM with 64 vCPUs
and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device)
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-3-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In commit a585fad26b ("vdpa: request iova_range only once") we remove
GET_IOVA_RANGE form vhost_vdpa_init, the generic vdpa device will start
without iova_range populated, so the device won't work. Let's call
GET_IOVA_RANGE ioctl explicitly.
Fixes: a585fad26b ("vdpa: request iova_range only once")
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221224114848.3062-2-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
hw/cxl/cxl_pci.h and hw/cxl/cxl_cdat.h include each other. The former
doesn't actually need the latter, so drop that inclusion to break the
loop.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-8-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/pci/pcie_sriov.h needs PCI_NUM_REGIONS. Without the previous
commit, this would close an inclusion loop: hw/pci/pci.h used to
include hw/pci/pcie.h for PCIExpressDevice, which includes
pcie_sriov.h for PCIESriovPF, which now includes hw/pci/pci.h for
PCI_NUM_REGIONS.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221222100330.380143-7-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/cxl/cxl.h uses the PXBDev structure tag instead of the typedef
name. The typedef name is defined in hw/pci/pci_bridge.h. Its
inclusion was dropped in the previous commit to break an inclusion
loop.
Move the typedef to hw/cxl/cxl.h, and use it there. Delete an extra
typedef in hw/pci-bridge/pci_expander_bridge.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/pci/pci_bridge.h and hw/cxl/cxl.h include each other.
Fortunately, breaking the loop is merely a matter of deleting
unnecessary includes from headers, and adding them back in places
where they are now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio.c is big enough, extract more QMP related code to virtio-qmp.c.
To do so, expose qmp_find_virtio_device() and declar virtio_list in
the internal virtio-qmp.h header.
Note we have to leave qmp_x_query_virtio_queue_status() and
qmp_x_query_virtio_queue_element(), because they access VirtQueue
internal fields, and VirtQueue is only declared within virtio.c.
Suggested-by: Jonah Palmer <jonah.palmer@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221222080005.27616-3-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt.
The configure interrupt process will start in vhost_dev_start
and stop in vhost_dev_stop.
Also add the functions to support vhost_config_pending and
vhost_config_mask.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-8-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the functions to support the configure interrupt in virtio
The function virtio_config_guest_notifier_read will notify the
guest if there is an configure interrupt.
The function virtio_config_set_guest_notifier_fd_handler is
to set the fd hander for the notifier
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-7-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add new call back function in vhost-vdpa, The function
vhost_set_config_call can set the event fd to kernel.
This function will be called in the vhost_dev_start
and vhost_dev_stop
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-6-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the interrupt process in configure interrupt
Need to decouple the single vector from the interrupt process.
We add new function kvm_virtio_pci_vector_use_one and _release_one.
These functions are used for the single vector, the whole process will
finish in the loop with vq number.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-4-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the notifier process. We add the virtio_pci_get_notifier
to get the notifier and vector. The INPUT for this function is IDX,
The OUTPUT is the notifier and the vector
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-3-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-2-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch aims to fix unexpected negotiation features for
vhost-user netdev interface.
When openvswitch reconnect Qemu after an unexpected disconnection
and Qemu therefore start the vhost_dev, acked_features field in
vhost_dev is initialized with value fetched from acked_features
field in NetVhostUserState, which should be up-to-date at that
moment but Qemu could not make it actually during the time window
of virtio features negotiation.
So we save the acked_features right after being configured by
guest virtio driver so it can be used to restore acked_features
field in vhost_dev correctly.
Signed-off-by: Hyman Huang(黄勇) <huangy81@chinatelecom.cn>
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Signed-off-by: Liuxiangdong <liuxiangdong5@huawei.com>
Message-Id: <b9f8cf5561a79ea65ea38960e5a5e6d3707eef0a.1671627406.git.huangy81@chinatelecom.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
piix4_pm_realize() uses apm_init() and pm_smbus_init(), so both APM and
ACPI_SMBUS are provided by the device model managed by ACPI_PIIX4.
The ACPIREGS are also provided by ACPI_PIIX4, so needs to select ACPI.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
TYPE_PIIX4_PM is only used in machines where PIIX chipsets are used
which is currently PC and Malta. There is no point building it for the
other ACPI_X86 machines.
Note that this also removes unneeded ACPI_PIIX4 from PEGASOS2.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
ich9_lpc_realize() uses apm_init() and ich9_smbus_realize() uses
pm_smbus_init(), so both APM and ACPI_SMBUS are provided by the device
models managed by ACPI_ICH9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although the ICH9 ACPI controller may currently be tied to x86 it
doesn't have to. Furthermore, the source files this configuration switch
manages contain a '9', so this name fits more.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pull-loongarch-20230106
# gpg: Signature made Fri 06 Jan 2023 06:21:22 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_pch: Change default irq number of pch irq controller
hw/intc/loongarch_pch_pic: add irq number property
hw/intc/loongarch_pch_msi: add irq number property
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Load constants in no more than two insns, which turns
out to be faster than using the constant pool.
Suggested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Merge maybe_out_small_movi, as it no longer has additional users.
Use is_const_p{16,32}.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Give 64-bit comparison second operand a signed 33-bit immediate.
This is the smallest superset of uint32_t and int32_t, as used
by CLGFI and CGFI respectively. The rest of the 33-bit space
can be loaded into TCG_TMP0. Drop use of the constant pool.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is an older form that produces per-byte results,
and a newer form that produces per-register results.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reuse code from movcond to conditionally copy a2 to dest,
based on the condition codes produced by FLOGR.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The new select instruction provides two separate register inputs,
whereas the old load-on-condition instruction overlaps one of the
register inputs with the destination.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Generalize movcond to support pre-computed conditions, and the same
set of arguments at all times. This will be assumed by a following
patch, which needs to reuse tgen_movcond_int.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Return both regular and inverted condition codes from tgen_cmp2.
This lets us choose after the fact which comparision we want.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is andc, orc, nand, nor, eqv.
We can use nor for implementing not.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Let the register allocator handle such immediates by matching
only what one insn can achieve.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Drop support for sequential OR and XOR, as the serial dependency is
slower than loading the constant first. Let the register allocator
handle such immediates by matching only what one insn can achieve.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is only one instruction that is applicable
to a 32-bit immediate xor.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The distinct-operands facility is bundled into facility 45,
along with load-on-condition. We are checking this at startup.
Remove the a0 == a1 checks for 64-bit sub, and, or, xor, as there
is no space savings for avoiding the distinct-operands insn.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The fast-bcr-serialization facility is bundled into facility 45,
along with load-on-condition. We are checking this at startup.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The general-instruction-extension facility was introduced in z196,
which itself was end-of-life in 2021. In addition, z196 is the
minimum CPU supported by our set of supported operating systems:
RHEL 7 (z196), SLES 12 (z196) and Ubuntu 16.04 (zEC12).
Check for facility number 45, which will be the consilidated check
for several facilities.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The general-instruction-extension facility was introduced in z10,
which itself was end-of-life in 2019.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The extended-immediate facility was introduced in z9-109,
which itself was end-of-life in 2017.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We are already assuming the existance of long-displacement, but were
not being explicit about it. This has been present since z990.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The size of a compiled TB is limited by the uint16_t used by
gen_insn_end_off[] -- there is no need for a 32-bit branch.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since USE_REG_TB is removed, there is no need to load the
target TB address into a register.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This reverts 829e1376d9 ("tcg/s390: Introduce TCG_REG_TB"), and
several follow-up patches. The primary motivation is to reduce the
less-tested code paths, pre-z10. Secondarily, this allows the
unconditional use of TCG_TARGET_HAS_direct_jump, which might be more
important for performance than any slight increase in code size.
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v4: Do not simplify tgen_ori, tgen_xori.
First RISC-V PR for QEMU 8.0
* Fix PMP propagation for tlb
* Collection of bug fixes
* Bump the OpenTitan supported version
* Add smstateen support
* Support native debug icount trigger
* Remove the redundant ipi-id property in the virt machine
* Support cache-related PMU events in virtual mode
* Add some missing PolarFire SoC io regions
* Fix mret exception cause when no pmp rule is configured
* Fix bug where disabling compressed instructions would crash QEMU
* Add Zawrs ISA extension support
* A range of code refactoring and cleanups
# gpg: Signature made Fri 06 Jan 2023 00:47:23 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* tag 'pull-riscv-to-apply-20230106' of https://github.com/alistair23/qemu: (43 commits)
hw/intc: sifive_plic: Fix the pending register range check
hw/riscv: opentitan: Drop "hartid-base" and "priority-base" initialization
hw/intc: sifive_plic: Change "priority-base" to start from interrupt source 0
hw/riscv: virt: Fix the value of "riscv, ndev" in the dtb
hw/riscv: sifive_u: Avoid using magic number for "riscv, ndev"
hw/riscv: sifive_e: Fix the number of interrupt sources of PLIC
hw/riscv: microchip_pfsoc: Fix the number of interrupt sources of PLIC
hw/intc: sifive_plic: Update "num-sources" property default value
hw/intc: sifive_plic: Use error_setg() to propagate the error up via errp in sifive_plic_realize()
hw/intc: sifive_plic: Improve robustness of the PLIC config parser
hw/intc: sifive_plic: Drop PLICMode_H
hw/riscv: spike: Remove misleading comments
hw/riscv: Sort machines Kconfig options in alphabetical order
hw/riscv: Fix opentitan dependency to SIFIVE_PLIC
hw/intc: Select MSI_NONBROKEN in RISC-V AIA interrupt controllers
hw/riscv: Select MSI_NONBROKEN in SIFIVE_PLIC
RISC-V: Add Zawrs ISA extension support
target/riscv: Clear mstatus.MPRV when leaving M-mode for priv spec 1.12+
target/riscv: Simplify helper_sret() a little bit
target/riscv: Set pc_succ_insn for !rvc illegal insn
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix race conditions in new user-only vma tracking.
Add tcg backend paired register allocation.
Cleanup tcg backend function call abi.
# gpg: Signature made Fri 06 Jan 2023 03:12:17 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20230105' of https://gitlab.com/rth7680/qemu: (47 commits)
tests/tcg/multiarch: add vma-pthread.c
accel/tcg: Handle false negative lookup in page_check_range
accel/tcg: Use g_free_rcu for user-exec interval trees
accel/tcg: Fix tb_invalidate_phys_page_unwind
tcg: Add TCGHelperInfo argument to tcg_out_call
tcg/aarch64: Merge tcg_out_callr into tcg_out_call
tcg: Move ffi_cif pointer into TCGHelperInfo
tcg: Factor init_ffi_layouts() out of tcg_context_init()
tcg: Convert typecode_to_ffi from array to function
tcg: Reorg function calls
tcg: Use output_pref wrapper function
tcg: Vary the allocation size for TCGOp
tcg: Pass number of arguments to tcg_emit_op() / tcg_op_insert_*()
accel/tcg/plugin: Use copy_op in append_{udata,mem}_cb
accel/tcg/plugin: Avoid duplicate copy in copy_call
accel/tcg/plugin: Don't search for the function pointer index
tcg: Use TCG_CALL_ARG_EVEN for TCI special case
tcg: Replace TCG_TARGET_EXTEND_ARGS with TCG_TARGET_CALL_ARG_I32
tcg: Replace TCG_TARGET_CALL_ALIGN_ARGS with TCG_TARGET_CALL_ARG_I64
tcg: Introduce TCGCallReturnKind and TCGCallArgumentKind
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hexagon update: patches from several folks
# gpg: Signature made Thu 05 Jan 2023 17:35:27 GMT
# gpg: using RSA key 3635C788CE62B91FD4C59AB47B0244FB12DE4422
# gpg: Good signature from "Taylor Simpson (Rock on) <tsimpson@quicinc.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3635 C788 CE62 B91F D4C5 9AB4 7B02 44FB 12DE 4422
* tag 'pull-hex-20230105' of https://github.com/quic/qemu:
Update scripts/meson-buildoptions.sh
Hexagon (target/hexagon) implement mutability mask for GPRs
target/hexagon: suppress unused variable warning
target/hexagon/idef-parser: fix two typos in README
tests/tcg/hexagon: fix underspecifed asm constraints
target/hexagon: rename aliased register HEX_REG_P3_0
linux-user/hexagon: fix signal context save & restore
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With loongarch 7A1000 manual, irq number supported can be set
in PCH_PIC_INT_ID_HI register. This patch adds irq number property
for loongarch_pch_pic, so that virt machine can set different
irq number when pch_pic intc is added.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230104020518.2564263-3-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The pending register upper limit is currently set to
plic->num_sources >> 3, which is wrong, e.g.: considering
plic->num_sources is 7, the upper limit becomes 0 which fails
the range check if reading the pending register at pending_base.
Fixes: 1e24429e40 ("SiFive RISC-V PLIC Block")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-16-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
changed the value of VIRT_IRQCHIP_NUM_SOURCES from 127 to 53, which
is VIRTIO_NDEV and also used as the value of "riscv,ndev" property
in the dtb. Unfortunately this is wrong as VIRT_IRQCHIP_NUM_SOURCES
should include interrupt source 0 but "riscv,ndev" does not.
While we are here, we also fix the comments of platform bus irq range
which is now "64 to 96", but should be "64 to 95", introduced since
commit 1832b7cb3f ("hw/riscv: virt: Create a platform bus").
Fixes: 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-13-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the default value of "num-sources" property is zero,
which does not make a lot of sense, as in sifive_plic_realize()
we see s->bitfield_words is calculated by:
s->bitfield_words = (s->num_sources + 31) >> 5;
if the we don't configure "num-sources" property its default value
zero makes s->bitfield_words zero too, which isn't true because
interrupt source 0 still occupies one word.
Let's change the default value to 1 meaning that only interrupt
source 0 is supported by default and a sanity check in realize().
While we are here, add a comment to describe the exact meaning of
this property that the number should include interrupt source 0.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-9-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PLIC config parser can only handle legal config string
like "MS,MS". However if a config string like ",MS,MS,,MS,MS,," is
given the parser won't get the correct configuration.
This commit improves the config parser to make it more robust.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-7-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in both riscv_aplic_realize() and
riscv_imsic_realize().
Select MSI_NONBROKEN in RISCV_APLIC and RISCV_IMSIC.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-2-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in sifive_plic_realize().
Let SIFIVE_PLIC select MSI_NONBROKEN and drop the selection from
RISC-V machines.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the Zawrs ISA extension.
Given the current (incomplete) implementation of reservation sets
there seems to be no way to provide a full emulation of the WRS
instruction (wake on reservation set invalidation or timeout or
interrupt). Therefore, we just exit the TB and return to the main loop.
The specification can be found here:
https://github.com/riscv/riscv-zawrs/blob/main/zawrs.adoc
Note, that the Zawrs extension is frozen, but not ratified yet.
Changes since v3:
* Remove "RFC" since the extension is frozen
* Rebase on master and fix integration issues
* Fix entry ordering in extension list
Changes since v2:
* Rebase on master and resolve conflicts
* Adjustments according to a specification change
* Inline REQUIRE_ZAWRS() since it has only one user
Changes since v1:
* Adding zawrs to the ISA string that is passed to the kernel
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221005144948.3421504-1-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The priv spec v1.12 says:
If no PMP entry matches an M-mode access, the access succeeds. If
no PMP entry matches an S-mode or U-mode access, but at least one
PMP entry is implemented, the access fails. Failed accesses generate
an instruction, load, or store access-fault exception.
At present the exception cause is set to 'illegal instruction' but
should have been 'instruction access fault'.
Fixes: d102f19a20 ("target/riscv/pmp: Raise exception if no PMP entry is configured")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221205065303.204095-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the number of interrupt is not multiple of 32, PLIC will have
out-of-bound access to source_priority array. Compute the number of
interrupt in the last word to avoid this out-of-bound access of array.
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221127165753.30533-1-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The system controller on PolarFire SoC is access via a mailbox. The
control registers for this mailbox lie in the "IOSCB" region & the
interrupt is cleared via write to the "SYSREG" region. It also has a
QSPI controller, usually connected to a flash chip, that is used for
storing FPGA bitstreams and used for In-Application Programming (IAP).
Linux has an implementation of the system controller, through which the
hwrng is accessed, leading to load/store access faults.
Add the QSPI as unimplemented and a very basic (effectively
unimplemented) version of the system controller's mailbox. Rather than
purely marking the regions as unimplemented, service the mailbox
requests by reporting failures and raising the interrupt so a guest can
better handle the lack of support.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221117225518.4102575-4-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Fabric Interconnect Controllers provide interfaces between the FPGA
fabric and the core complex. There are 5 FICs on PolarFire SoC, numbered
0 through 4. FIC2 is an AXI4 slave interface from the FPGA fabric and
does not show up on the MSS memory map. FIC4 is dedicated to the User
Crypto Processor and does not show up on the MSS memory map either.
FIC 0, 1 & 3 do show up in the MSS memory map and neither FICs 0 or 1
are represented in QEMU, leading to load access violations while booting
Linux for Icicle if PCIe is enabled as the root port is connected via
either FIC 0 or 1.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-3-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On PolarFire SoC, some peripherals (eg the PCI root port) are clocked by
"Clock Conditioning Circuitry" in the FPGA. The specific clock depends
on the FPGA bitstream & can be locked to one particular {D,P}LL - in the
Icicle Kit Reference Design v2022.09 or later this is/will be the case.
Linux v6.1+ will have a driver for this peripheral and devicetrees that
previously relied on "fixed-frequency" clock nodes have been switched
over to clock-controller nodes. The IOSCB region is represented in QEMU,
but the specific region of it that the CCCs occupy has not so v6.1-rcN
kernels fail to boot in QEMU.
Add the regions as unimplemented so that the status-quo in terms of boot
is maintained.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-2-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
sstatus register dump is currently missing in riscv_cpu_dump_state().
As sstatus is a copy of mstatus, which is described in the priv spec,
it seems redundant to print the same information twice.
Add some comments for this to let people know this is intentional.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221125050354.3166023-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 40244040a7 changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When QEMU is not in icount mode, execute instruction one by one. The
tdata1 can be read directly.
When QEMU is in icount mode, use a timer to simulate the itrigger. The
tdata1 may be not right because of lazy update of count in tdata1. Thus,
We should pack the adjusted count into tdata1 before read it back.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-4-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The max count in itrigger can be 0x3FFF, which will cause a no trivial
translation and execution overload.
When icount is enabled, QEMU provides API that can fetch guest
instruction number. Thus, we can set an timer for itrigger with
the count as deadline.
Only when timer expires or priviledge mode changes, do lazy update
to count.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-3-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When icount is not enabled, there is no API in QEMU that can get the
guest instruction number.
Translate the guest code in a way that each TB only has one instruction.
After executing the instruction, decrease the count by 1 until it reaches 0
where the itrigger fires.
Note that only when priviledge matches the itrigger configuration,
the count will decrease.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-2-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When guest_base != 0, we were not coordinating the usage of
TCG_REG_TMP0 as base properly, leading to a previous zero-extend
of the input address being discarded.
Shuffle the alignment check to the front, because that does not
depend on the zero-extend, and it keeps the register usage clear.
Set base after each step of the address arithmetic instead of before.
Return the base register used from tcg_out_tlb_load, so as to
keep that register choice localized to that function.
Reported-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221023233337.2846860-1-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Only the pmp index that be checked by pmp_hart_has_privs can be used
by pmp_get_tlb_size to avoid an error pmp index.
Before modification, we may use an error pmp index. For example,
we check address 0x4fc, and the size 0x4 in pmp_hart_has_privs. If there
is an pmp rule, valid range is [0x4fc, 0x500), then pmp_hart_has_privs
will return true;
However, this checked pmp index is discarded as pmp_hart_has_privs
return bool value. In pmp_is_range_in_tlb, it will traverse all pmp
rules. The tlb_sa will be 0x0, and tlb_ea will be 0xfff. If there is
a pmp rule [0x10, 0x14), it will be misused as it is legal in
pmp_get_tlb_size.
As we have already known the correct pmp index, just remove the
remove the pmp_is_range_in_tlb and get tlb size directly from
pmp_get_tlb_size.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221012060016.30856-1-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
-machine kernel-irqchip=off is broken for many guest OSes; kernel-irqchip=split
is the replacement that works, so remove the deprecated support for the former.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When installing shared libraries, as is the case for libvfio-user.so,
Meson will include relative symbolic links in the output of
"meson introspect --installed":
{
"libvfio-user.so": "/usr/local/lib64/libvfio-user.so",
...
}
In the case of scripts/symlink-install-tree.py, this will
be a symbolic link to a symbolic link but, in any case, there is
no issue in creating it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Detect all compilers at the beginning of meson.build, and store
the available languages in an array.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In Meson 0.64, the optimization built-in option now accepts the "plain" value,
which will not set any optimization flags. While QEMU does not check the
contents of the option and therefore does not suffer any ill effect
from the new value, it uses get_option to print the optimization flags
in the summary. Clean the code up to remove duplication, and check for
-Doptimization=plain at the same time.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some warnings are hardcoded in QEMU_CFLAGS and not tested. There is
no particular reason to single out these five, as many more -W flags are
present on all the supported compilers. For homogeneity when moving
the detection to meson, make them use the same warn_flags infrastructure.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that qtest is available on all targets including Windows, dummy-cpus.c
is included unconditionally in the build. It also does not need to be
compiled per-target.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
meson.build has been enabling ASLR _only_ for debug builds since
commit d2147e04f9 ("configure: move Windows flags detection to meson",
2022-05-07); instead it was supposed to disable it for debug builds.
However, the flag has been enabled for DLLs upstream for roughly 2
years (https://sourceware.org/bugzilla/show_bug.cgi?id=19011), and
also by some distros including Debian for 6 years even
(https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=836365).
Enable it unconditionally; we can fix the reversed logic of commit
d2147e04f9 later if there are any reports, but for now just
enable the hardening.
Also add -Wl,--high-entropy-va, which also controls ASLR.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ensure that qemu-ga variables set at configure time are kept
later when the script is rerun. For preserve_env to work,
the variables need to be empty so move the default values
to config-host.mak generation.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
$cpu is derived from preprocessor defines rather than uname these days,
so do not bother using isainfo on Solaris. Likewise do not recognize
BeOS's uname -m output.
Keep the other, less OS-specific canonicalizations for the benefit
of people using --cpu.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not needed ever since QEMU stopped detecting -liberty; this
happened with the Meson switch but it is quite likely that the
library was not really necessary years before.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows attaching IDE_CFATA device to an IDE bus. Behaves like a
CompactFlash card in True IDE mode.
Tested with:
qemu-system-i386 \
-device driver=ide-cf,drive=cf,bus=ide.0 \
-drive id=cf,index=0,format=raw,if=none,file=cf.img
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Message-Id: <20221130120319.706885-1-lkundrak@v3.sk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When QEMU is started with `-daemonize`, all stdio descriptors get
redirected to `/dev/null`. This basically means that anything
printed with error_report() and friends is lost.
Current logging code allows to redirect to a file with `-D` but
this requires to enable some logging item with `-d` as well to
be functional.
Relax the check on the log flags when QEMU is daemonized, so that
other users of stderr can benefit from the redirection, without the
need to enable unwanted debug logs. Previous behaviour is retained
for the non-daemonized case. The logic is unrolled as an `if` for
better readability. The qemu_log_level and log_per_thread globals
reflect the state we want to transition to at this point : use
them instead of the intermediary locals for correctness.
qemu_set_log_internal() is adapted to open a per-thread log file
when '-d tid' is passed. This is done by hijacking qemu_try_lock()
which seems simpler that refactoring the code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20221108140032.1460307-3-groug@kaod.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
log_append makes sure that if you turn off the logging (which clears
log_flags and makes need_to_open_file false) the old log is not
overwritten. The usecase is that if you remove or move the file
QEMU will not keep writing to the old file. However, this is
not always the desited behavior, in particular having log_append==1
after changing the file name makes little sense.
When qemu_set_log_internal is called from the logfile monitor
command, filename must be non-NULL and therefore changed_name must
be true. Therefore, the only case where the file is closed and
need_to_open_file == false is indeed when log_flags becomes
zero. In this case, just flush the file and do not bother
closing it, thus faking the same append behavior as previously.
The behavioral change is that changing the logfile twice, for
example log1 -> log2 -> log1, will cause log1 to be overwritten.
This can simply be documented, since it is not a particularly
surprising behavior.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20221025092119.236224-1-pbonzini@redhat.com>
[groug: nullify global_file before actually closing the file]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20221108140032.1460307-2-groug@kaod.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Forward-declare AccelState in "qemu/typedefs.h" so structures
using a reference of it (like MachineState in "hw/boards.h")
don't have to include "qemu/accel.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-Id: <20221130135641.85328-2-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As in page_get_flags, we need to try again with the mmap
lock held if we fail a page lookup.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Because we allow lockless lookups, we have to be careful
when it is freed. Use rcu to delay the free until safe.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When called from syscall(), we are not within a TB and pc == 0.
We can skip the check for invalidating the current TB.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This eliminates an ifdef for TCI, and will be required for
expanding the call for TCGv_i128.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is only one use, and BLR is perhaps even more
self-documentary than CALLR.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Pre-compute the function call layout for each helper at startup.
Drop TCG_CALL_DUMMY_ARG, as we no longer need to leave gaps
in the op->args[] array. This allows several places to stop
checking for NULL TCGTemp, to which TCG_CALL_DUMMY_ARG mapped.
For tcg_gen_callN, loop over the arguments once. Allocate the TCGOp
for the call early but delay emitting it, collecting arguments first.
This allows the argument processing loop to emit code for extensions
and have them sequenced before the call.
For tcg_reg_alloc_call, loop over the arguments in reverse order,
which allows stack slots to be filled first naturally.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will shortly have the possibility of more that two outputs,
though only for calls (for which preferences are moot). Avoid
direct references to op->output_pref[] when possible.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have been allocating a worst case number of arguments
to support calls. Instead, allow the size to vary.
By default leave space for 4 args, to maximize reuse,
but allow calls to increase the number of args to 32.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Split patch in two]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221218211832.73312-3-philmd@linaro.org>
In order to have variable size allocated TCGOp, pass the number
of arguments we use (and would allocate) up to tcg_op_alloc().
This alters tcg_emit_op(), tcg_op_insert_before() and
tcg_op_insert_after() prototypes.
In tcg_op_alloc() ensure the number of arguments is in range.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Extracted from bigger patch]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221218211832.73312-2-philmd@linaro.org>
We copied all of the arguments in copy_op_nocheck.
We only need to replace the one argument that we change.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The function pointer is immediately after the output and input
operands; no need to search.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Change 32-bit tci TCG_TARGET_CALL_ARG_I32 to TCG_CALL_ARG_EVEN, to
force 32-bit values to be aligned to 64-bit. With a small reorg
to the argument processing loop, this neatly replaces an ifdef for
CONFIG_TCG_INTERPRETER.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For 64-bit hosts that had TCG_TARGET_EXTEND_ARGS, set
TCG_TARGET_CALL_ARG_I32 to TCG_CALL_ARG_EXTEND.
Otherwise, use TCG_CALL_ARG_NORMAL.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For 32-bit hosts when TCG_TARGET_CALL_ALIGN_ARGS was set, use
TCG_CALL_ARG_EVEN. For 64-bit hosts, TCG_TARGET_CALL_ALIGN_ARGS
was silently ignored, so always use TCG_CALL_ARG_NORMAL.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Prepare to replace a bunch of separate ifdefs with a
consistent way to describe the ABI of a function call.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The count is not itself an enumerator. Move it outside to
prevent the compiler from considering it with -Wswitch-enum.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allocate the first of a pair at the lower address, and the
second of a pair at the higher address. This will make it
easier to find the beginning of the larger memory block.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The first thing that temp_sync does is check mem_coherent,
so there's no need for the caller to do so.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move the error-generating fallback from tcg-op.c, and
replace "_link_error" with modern QEMU_ERROR markup.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While we initialize this value in cpu_common_reset, that
isn't called during startup, so set it as well in init.
This fixes -singlestep versus the very first TB.
Fixes: 04f5b647ed ("accel/tcg: Handle -singlestep in curr_cflags")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There are several instances where we need to be able to
allocate a pair of registers to related inputs/outputs.
Add 'p' and 'm' register constraints for this, in order to
be able to allocate the even/odd register first or second.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Note: `Makefile` relies on modification dates in the source tree to
detect changes to `meson_options.txt`. However, git does not track
those. Therefore, the following was necessary to regenerate
`meson-buildoptions.sh`:
touch meson_options.txt
cd "$BUILD_DIR"
make update-buildoptions
Signed-off-by: Alessandro Di Federico <ale@rev.ng>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20230102104113.3438895-1-ale@rev.ng>
This patch manually suppresses a warning for an unused variable
(yynerrs) emitted by bison.
This warning has been triggered for the first time by clang 15.
This patch also disables `-Wextra`, which is not usually adopted in
QEMU. However, clang 15 triggers the warning fixed in this patch even in
absence of `-Wextra`.
Signed-off-by: Alessandro Di Federico <ale@rev.ng>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Tested-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221221155327.1504117-1-ale@rev.ng>
There are two test cases where the inline asm doesn't
have the correct constraints causing them to fail.
In misc.c, the 'result' output needs the early clobber
modifier since the rest of the inputs are read after
assignment to the output register.
In mem_noshuf.c, the register r7 is written to but
not specified in the clobber list.
Signed-off-by: Mukilan Thiyagarajan <quic_mthiyaga@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221229081836.12130-1-quic_mthiyaga@quicinc.com>
The patch renames the identifier of the 32bit register
HEX_REG_P3_0 to HEX_REG_P3_0_ALIASED.
This change is to intended to provide some warning that
HEX_REG_P3_0 is an aliased register which has multiple
representations in CPU state and therefore might require
special handling in some contexts. The hope is to prevent
accidental misuse of this register e.g the issue reported
for the signals tests failure [here][1].
[1]: https://lists.gnu.org/archive/html/qemu-devel/2021-11/msg01102.html
Signed-off-by: Mukilan Thiyagarajan <quic_mthiyaga@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221229092006.10709-3-quic_mthiyaga@quicinc.com>
This patch fixes the issue originally reported in
this thread:
https://lists.gnu.org/archive/html/qemu-devel/2021-11/msg01102.html
The root cause of the issue is a bug in the hexagon specific
logic for saving & restoring context during signal delivery.
The CPU state has two different representations for the
predicate registers. The current logic saves & restores only
the aliased HEX_REG_P3_O register, which is part of env->gpr[]
field in the CPU state, but not the individual byte-level
predicate registers (pO, p1, p2, p3) backed by env->pred[].
Since all predicated instructions refer only to the
indiviual registers, switching to and back from a signal handler
can clobber these registers if the signal handler writes to them
causing the normal application code to behave unpredictably when
context is restored.
In the reported issue with the 'signals' test, since the updated
hexagon toolchain had built musl with -O2, the functions called
from non_trivial_free were inlined. This meant that the code
emitted reused predicate P0 computed in the entry translation
block of the function non_trivial_free in one of the child TB
as part of an assertion. Since P0 is clobbered by the signal
handler in the signals test, the assertion in non_trivial_free
fails incorectly. Since musl for hexagon implements the 'abort'
function by deliberately writing to memory via null pointer,
this causes the test to fail with segmentation fault.
This patch modifies the signal context save & restore logic
to include the individual p0, p1, p2, p3 and excludes the
32b p3_0 register since its value is derived from the former
registers. It also adds a new test case that reliabily
reproduces the issue for all four predicate registers.
Buglink: https://github.com/quic/toolchain_for_hexagon/issues/6
Signed-off-by: Mukilan Thiyagarajan <quic_mthiyaga@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221229092006.10709-2-quic_mthiyaga@quicinc.com>
Size is used at lines 1088/1188 for the loop, which reads the last 4
bytes from the crc_ptr so it does need to get increased, however it
shouldn't be increased before the buffer is passed to CRC computation,
or the crc32 function will access uninitialized memory.
This was pointed out to me by clg@kaod.org during the code review of
a similar patch to hw/net/ftgmac100.c
Change-Id: Ib0464303b191af1e28abeb2f5105eb25aadb5e9b
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20221221183202.3788132-1-slongfield@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using Clang ("Apple clang version 14.0.0 (clang-1400.0.29.202)")
and building with -Wall we get:
hw/arm/smmu-common.c:173:33: warning: static function 'smmu_hash_remove_by_asid_iova' is used in an inline function with external linkage [-Wstatic-in-inline]
hw/arm/smmu-common.h:170:1: note: use 'static' to give inline function 'smmu_iotlb_inv_iova' internal linkage
void smmu_iotlb_inv_iova(SMMUState *s, int asid, dma_addr_t iova,
^
static
None of our code base require / use inlined functions with external
linkage. Some places use internal inlining in the hot path. These
two functions are certainly not in any hot path and don't justify
any inlining, so these are likely oversights rather than intentional.
Reported-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221216214924.4711-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In CPUID registers exposed to userspace, some registers were missing
and some fields were not exposed. This patch aligns exposed ID
registers and their fields with what the upstream kernel currently
exposes.
Specifically, the following new ID registers/fields are exposed to
userspace:
ID_AA64PFR1_EL1.BT: bits 3-0
ID_AA64PFR1_EL1.MTE: bits 11-8
ID_AA64PFR1_EL1.SME: bits 27-24
ID_AA64ZFR0_EL1.SVEver: bits 3-0
ID_AA64ZFR0_EL1.AES: bits 7-4
ID_AA64ZFR0_EL1.BitPerm: bits 19-16
ID_AA64ZFR0_EL1.BF16: bits 23-20
ID_AA64ZFR0_EL1.SHA3: bits 35-32
ID_AA64ZFR0_EL1.SM4: bits 43-40
ID_AA64ZFR0_EL1.I8MM: bits 47-44
ID_AA64ZFR0_EL1.F32MM: bits 55-52
ID_AA64ZFR0_EL1.F64MM: bits 59-56
ID_AA64SMFR0_EL1.F32F32: bit 32
ID_AA64SMFR0_EL1.B16F32: bit 34
ID_AA64SMFR0_EL1.F16F32: bit 35
ID_AA64SMFR0_EL1.I8I32: bits 39-36
ID_AA64SMFR0_EL1.F64F64: bit 48
ID_AA64SMFR0_EL1.I16I64: bits 55-52
ID_AA64SMFR0_EL1.FA64: bit 63
ID_AA64MMFR0_EL1.ECV: bits 63-60
ID_AA64MMFR1_EL1.AFP: bits 47-44
ID_AA64MMFR2_EL1.AT: bits 35-32
ID_AA64ISAR0_EL1.RNDR: bits 63-60
ID_AA64ISAR1_EL1.FRINTTS: bits 35-32
ID_AA64ISAR1_EL1.BF16: bits 47-44
ID_AA64ISAR1_EL1.DGH: bits 51-48
ID_AA64ISAR1_EL1.I8MM: bits 55-52
ID_AA64ISAR2_EL1.WFxT: bits 3-0
ID_AA64ISAR2_EL1.RPRES: bits 7-4
ID_AA64ISAR2_EL1.GPA3: bits 11-8
ID_AA64ISAR2_EL1.APA3: bits 15-12
The code is also refactored to use symbolic names for ID register fields
for better readability and maintainability.
The test case in tests/tcg/aarch64/sysregs.c is also updated to match
the intended behavior.
Signed-off-by: Zhuojia Shen <chaosdefinition@hotmail.com>
Message-id: DS7PR12MB6309FB585E10772928F14271ACE79@DS7PR12MB6309.namprd12.prod.outlook.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: use Sn_n_Cn_Cn_n syntax to work with older assemblers
that don't recognize id_aa64isar2_el1 and id_aa64mmfr2_el1]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hi,
"Host Memory Backends" and "Memory devices" queue ("mem"):
- virtio-mem fixes
- Use new MPOL_PREFERRED_MANY mbind() policy for memory backends if
possible
# gpg: Signature made Mon 02 Jan 2023 11:22:04 GMT
# gpg: using RSA key 1BD9CAAD735C4C3A460DFCCA4DDE10F700FF835A
# gpg: issuer "david@redhat.com"
# gpg: Good signature from "David Hildenbrand <david@redhat.com>" [marginal]
# gpg: aka "David Hildenbrand <davidhildenbrand@gmail.com>" [full]
# gpg: aka "David Hildenbrand <hildenbr@in.tum.de>" [unknown]
# Primary key fingerprint: 1BD9 CAAD 735C 4C3A 460D FCCA 4DDE 10F7 00FF 835A
* tag 'mem-2023-01-02' of https://github.com/davidhildenbrand/qemu:
hostmem: Honor multiple preferred nodes if possible
virtio-mem: Fix typo in function name
virtio-mem: Fix the iterator variable in a vmem->rdl_list loop
virtio-mem: Fix the bitmap index of the section offset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the following:
ERROR: spaces required around that '|' (ctx:VxV)
ERROR: space required before the open parenthesis '('
ERROR: spaces required around that '+' (ctx:VxB)
ERROR: space prohibited between function name and open parenthesis '('
(the last two still have some occurrences in macros which I left
behind because it might impact readability)
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20221213190537.511-3-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- fix#1263 for CR writes
- rework compare time handling
- The compare timer has to run even if CR.OCIEN is not set,
as SR.OCIF must be updated.
- The compare timer fires exactly once when the
compare value is less than the current value, but the
reload values is less than the compare value.
- The compare timer will never fire if the reload value is
less than the compare value. Disable it in this case.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
[PMM: fixed minor style nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CNT register is a read-only register. There is no need to
store it's value, it can be calculated on demand.
The calculated frequency is needed temporarily only.
Note that this is a migration compatibility break for all boards
types that use the EPIT peripheral.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The check semihosting_enabled() wants to know if the guest is
currently in user mode. Unlike the other cases the test was inverted
causing us to block semihosting calls in non-EL0 modes.
Cc: qemu-stable@nongnu.org
Fixes: 19b26317e9 (target/arm: Honour -semihosting-config userspace=on)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The v8R PMSAv8 has a two-stage MPU translation process, but, unlike
VMSAv8, the stage 2 attributes are in the same format as the stage 1
attributes (8-bit MAIR format). Rather than converting the MAIR
format to the format used for VMSA stage 2 (bits [5:2] of a VMSA
stage 2 descriptor) and then converting back to do the attribute
combination, allow combined_attrs_nofwb() to accept s2 attributes
that are already in the MAIR format.
We move the assert() to combined_attrs_fwb(), because that function
really does require a VMSA stage 2 attribute format. (We will never
get there for v8R, because PMSAv8 does not implement FEAT_S2FWB.)
Signed-off-by: Tobias Röhmel <tobias.roehmel@rwth-aachen.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221206102504.165775-4-tobias.roehmel@rwth-aachen.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In get_phys_addr_twostage() we set the lg_page_size of the result to
the maximum of the stage 1 and stage 2 page sizes. This works for
the case where we do want to create a TLB entry, because we know the
common TLB code only creates entries of the TARGET_PAGE_SIZE and
asking for a size larger than that only means that invalidations
invalidate the whole larger area. However, if lg_page_size is
smaller than TARGET_PAGE_SIZE this effectively means "don't create a
TLB entry"; in this case if either S1 or S2 said "this covers less
than a page and can't go in a TLB" then the final result also should
be marked that way. Set the resulting page size to 0 if either
stage asked for a less-than-a-page entry, and expand the comment
to explain what's going on.
This has no effect for VMSA because currently the VMSA lookup always
returns results that cover at least TARGET_PAGE_SIZE; however when we
add v8R support it will reuse this code path, and for v8R the S1 and
S2 results can be smaller than TARGET_PAGE_SIZE.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221212142708.610090-1-peter.maydell@linaro.org
We now check the consistency of reg_to_temp[] with each update,
so the utility of checking consistency at the end of each
opcode is minimal. In addition, the form of this check is
quite expensive, consuming 10% of a checking-enabled build.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Create two new functions, set_temp_val_{reg,nonreg}.
Assert that the reg_to_temp mapping is correct before
any changes are made.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The assignment to mem_coherent should be done with any
modification, not simply with a newly allocated register.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The hppa host code has been removed since 2013; this
should have been deleted at the same time.
Fixes: 802b508123 ("tcg-hppa: Remove tcg backend")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace goto allocate_in_reg with a boolean.
Remove o_preferred_regs which isn't used, except to copy.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Narrow the scope of the lock to the actual read/write,
moving the cpu_transation_failed call outside the lock.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Remove whitespace at end of line, plus one place this also
highlights some missing braces.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Like CONFIG_TCG, the enabled method of execution is a host property
not a guest property. This exposes the define to compile-once files.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Convert tcg/README to rst and move it to docs/devel as a new "TCG Intermediate
Representation" page. There are a few minor changes to improve the aesthetic
of the final output which are as follows:
- Rename the title from "Tiny Code Generator - Fabrice Bellard" to "TCG
Intermediate Representation"
- Remove the section numbering
- Add the missing parameters to the ssadd_vec operations in the "Host
vector operations" section
- Change the path to the Atomic Operations document to use a proper
reference
- Replace tcg/README in tcg.rst with a proper reference to the new document
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-Id: <20221130100434.64207-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The windows jobs (especially the 32-bit job) recently started to
hit the timeout limit. Bump it a little bit to ease the situation
(80 minutes is quite long already - OTOH, these jobs do not have to
wait for a job from the container stage to finish, so this should
still be OK).
Additionally, some update on the container side recently enabled
OpenGL in these jobs - but the corresponding code fails to compile.
Thus disable OpenGL here for the time being until someone figured
out the proper fix in the shader code for this.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20230104123559.277586-1-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we request a shutdown of a VM without a QMP console, we'll just hang
waiting. Not ideal.
Add in code that attempts graceful termination in these cases. Tested
lightly; it appears to work and I doubt we rely on this case anywhere,
but it's a corner you're allowed to wedge yourself in, so it should be
handled.
Signed-off-by: John Snow <jsnow@redhat.com>
When key decisions are made about the lifetime of the VM process being
managed, there's no log entry. Juxtaposed with the very verbose runstate
change logging of the QMP module, machine seems a bit too introverted
now.
Season the machine.py module with logging statements to taste to help
make a tastier soup.
Signed-off-by: John Snow <jsnow@redhat.com>
testing updates:
- fix minor shell-ism that can break check-tcg
- turn off verbose logging on custom runners
- make configure echo call in CI
- fix unused variable in linux-test
- add binary compiler docker image for hexagon
- disable doc and gui builds for tci and disable-tcg builds
# gpg: Signature made Fri 23 Dec 2022 15:18:41 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-testing-next-231222-1' of https://gitlab.com/stsquad/qemu:
gitlab-ci: Disable docs and GUIs for the build-tci and build-tcg-disabled jobs
tests/docker: use prebuilt toolchain for debian-hexagon-cross
tests/tcg: fix unused variable in linux-test
configure: repeat ourselves for the benefit of CI
gitlab: turn off verbose logging for make check on custom runners
configure: Fix check-tcg not executing any tests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
9pfs: Windows host prep, cleanup
* Next preparatory patches for upcoming Windows host support.
* Cleanup patches.
# gpg: Signature made Fri 23 Dec 2022 11:04:26 GMT
# gpg: using RSA key 96D8D110CF7AF8084F88590134C2B58765A47395
# gpg: issuer "qemu_oss@crudebyte.com"
# gpg: Good signature from "Christian Schoenebeck <qemu_oss@crudebyte.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: ECAB 1A45 4014 1413 BA38 4926 30DB 47C3 A012 D5F4
# Subkey fingerprint: 96D8 D110 CF7A F808 4F88 5901 34C2 B587 65A4 7395
* tag 'pull-9p-20221223' of https://github.com/cschoenebeck/qemu:
hw/9pfs: Replace the direct call to xxxat() APIs with a wrapper
hw/9pfs: Drop unnecessary *xattr wrapper API declarations
qemu/xattr.h: Exclude <sys/xattr.h> for Windows
MAINTAINERS: Add 9p test client to section "virtio-9p"
9pfs: Fix some return statements in the synth backend
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If a memory-backend is configured with mode
HOST_MEM_POLICY_PREFERRED then
host_memory_backend_memory_complete() calls mbind() as:
mbind(..., MPOL_PREFERRED, nodemask, ...);
Here, 'nodemask' is a bitmap of host NUMA nodes and corresponds
to the .host-nodes attribute. Therefore, there can be multiple
nodes specified. However, the documentation to MPOL_PREFERRED
says:
MPOL_PREFERRED
This mode sets the preferred node for allocation. ...
If nodemask specifies more than one node ID, the first node
in the mask will be selected as the preferred node.
Therefore, only the first node is honored and the rest is
silently ignored. Well, with recent changes to the kernel and
numactl we can do better.
The Linux kernel added in v5.15 via commit cfcaa66f8032
("mm/hugetlb: add support for mempolicy MPOL_PREFERRED_MANY")
support for MPOL_PREFERRED_MANY, which accepts multiple preferred
NUMA nodes instead.
Then, numa_has_preferred_many() API was introduced to numactl
(v2.0.15~26) allowing applications to query kernel support.
Wiring this all together, we can pass MPOL_PREFERRED_MANY to the
mbind() call instead and stop ignoring multiple nodes, silently.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <a0b4adce1af5bd2344c2218eb4a04b3ff7bcfdb4.1671097918.git.mprivozn@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
The current docker image for cross compiling hexagon guests
is manually built since it takes >2 hours to build from source.
This patch:
1. Solves the above issue by using the prebuilt clang
toolchain hosted on CodeLinaro [1] and maintained by QUIC [2].
2. The dockerfile is also switched from multi-stage to single stage
build to allow the CI docker engine to reuse the layer cache.
3. Re-enables the hexagon-cross-container job to be always run in
CI and makes it a non-optional dependency for the
build-user-hexagon job.
The changes for 1 & 2 together bring down the build time to
~3 minutes in GitLab CI when cache is reused and ~9 minutes
when cache cannot be reused.
[1]: https://github.com/CodeLinaro/hexagon-builder
[2]: https://github.com/quic/toolchain_for_hexagon/releases/
Signed-off-by: Mukilan Thiyagarajan <quic_mthiyaga@quicinc.com>
[AJB: also tweak MAINTAINERS, remove QEMU_JOB_ONLY_FORKS and comment]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20221219144354.11659-1-quic_mthiyaga@quicinc.com>
Message-Id: <20221221090411.1995037-6-alex.bennee@linaro.org>
The latest hexagon compiler picks up that we never consume wcount.
Given the name of the #define that rcount checks against is WCOUNT_MAX
I figured the check just got missed.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221221090411.1995037-5-alex.bennee@linaro.org>
Our CI system echos the lines it executes but not the expansions. For
the sake of a line of extra verbosity during the configure phase lets
echo the invocation of script to stdout as well as the log when on CI.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221221090411.1995037-4-alex.bennee@linaro.org>
The verbosity adds a lot of unnecessary output to the CI logs which
end up getting truncated anyway. We can always extract information
from the meson test logs on a failure and for the custom runners its
generally easier to re-create failures anyway.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20221221090411.1995037-3-alex.bennee@linaro.org>
After configuring with --target-list=hexagon-linux-user
running `make check-tcg` just prints the following:
```
make: Nothing to be done for 'check-tcg'
```
In the probe_target_compiler function, the 'break'
command is used incorrectly. There are no lexically
enclosing loops associated with that break command which
is an unspecfied behaviour in the POSIX standard.
The dash shell implementation aborts the currently executing
loop, in this case, causing the rest of the logic for the loop
in line 2490 to be skipped, which means no Makefiles are
generated for the tcg target tests.
Fixes: c3b570b5a9 (configure: don't enable
cross compilers unless in target_list)
Signed-off-by: Mukilan Thiyagarajan <quic_mthiyaga@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Link: https://patchew.org/QEMU/20221207082309.9966-1-quic._5Fmthiyaga@quicinc.com/
Message-Id: <20221207082309.9966-1-quic_mthiyaga@quicinc.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20221221090411.1995037-2-alex.bennee@linaro.org>
The 9p test cases use a dedicated, lite-weight 9p client implementation
(using virtio transport) under tests/qtest/libqos/ to communicate with
QEMU's 9p server.
It's already there for a long time. Let's officially assign it to 9p
maintainers.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <E1ozhlV-0007BU-0g@lizzy.crudebyte.com>
The qemu_v9fs_synth_mkdir() and qemu_v9fs_synth_add_file() functions
currently return a positive errno value on failure. This causes
checkpatch.pl to spit several errors like the one below:
ERROR: return of an errno should typically be -ve (return -EAGAIN)
+ return EAGAIN;
Simply change the sign. This has no consequence since callers
assert() the returned value to be equal to 0.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <166930551818.827792.10663674346122681963.stgit@bahia>
[C.S.: - Resolve conflict with 66997c42e0. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
ppc patch queue for 2022-12-21:
This queue contains a MAINTAINERS update, the implementation of the Freescale eSDHC,
the introduction of the DEXCR/HDEXCR instructions and other assorted fixes (most of
them for the e500 board).
# gpg: Signature made Wed 21 Dec 2022 17:18:53 GMT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20221221' of https://gitlab.com/danielhb/qemu:
target/ppc: Check DEXCR on hash{st, chk} instructions
target/ppc: Implement the DEXCR and HDEXCR
hw/ppc/e500: Move comment to more appropriate place
hw/ppc/e500: Resolve variable shadowing
hw/ppc/e500: Prefer local variable over qdev_get_machine()
hw/ppc/virtex_ml507: Prefer local over global variable
target/ppc/mmu_common: Fix table layout of "info tlb" HMP command
target/ppc/mmu_common: Log which effective address had no TLB entry found
hw/ppc/spapr: Reduce "vof.h" inclusion
hw/ppc/vof: Do not include the full "cpu.h"
target/ppc/kvm: Add missing "cpu.h" and "exec/hwaddr.h"
hw/ppc/e500: Add Freescale eSDHC to e500plat
hw/sd/sdhci: Support big endian SD host controller interfaces
MAINTAINERS: downgrade PPC KVM/TCG CPUs and pSeries to 'Odd Fixes'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds checks to the hashst and hashchk instructions to only execute if
enabled by the relevant aspect in the DEXCR and HDEXCR.
This behaviour is guarded behind TARGET_PPC64 since Power10 is
currently the only implementation which has the DEXCR.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Nicholas Miehlbradt <nicholas@linux.ibm.com>
Message-Id: <20221220042330.2387944-3-nicholas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Define the DEXCR and HDEXCR as special purpose registers.
Each register occupies two SPR indicies, one which can be read in an
unprivileged state and one which can be modified in the appropriate
priviliged state, however both indicies refer to the same underlying
value.
Note that the ISA uses the abbreviation UDEXCR in two different
contexts: the userspace DEXCR, the SPR index which can be read from
userspace (implemented in this patch), and the ultravisor DEXCR, the
equivalent register for the ultravisor state (not implemented).
Signed-off-by: Nicholas Miehlbradt <nicholas@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221220042330.2387944-2-nicholas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Currently objects including "hw/ppc/spapr.h" are forced to be
target specific due to the inclusion of "vof.h" in "spapr.h".
"spapr.h" only uses a Vof pointer, so doesn't require the structure
declaration. The only place where Vof structure is accessed is in
spapr.c, so include "vof.h" there, and forward declare the structure
in "spapr.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221213123550.39302-4-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
kvm_ppc.h is missing various declarations from "cpu.h":
target/ppc/kvm_ppc.h:128:40: error: unknown type name 'CPUPPCState'; did you mean 'CPUState'?
static inline int kvmppc_get_hypercall(CPUPPCState *env,
^~~~~~~~~~~
CPUState
include/qemu/typedefs.h:45:25: note: 'CPUState' declared here
typedef struct CPUState CPUState;
^
target/ppc/kvm_ppc.h:134:40: error: unknown type name 'PowerPCCPU'
static inline int kvmppc_set_interrupt(PowerPCCPU *cpu, int irq, int level)
^
target/ppc/kvm_ppc.h:285:38: error: unknown type name 'hwaddr'
hwaddr ptex, int n)
^
target/ppc/kvm_ppc.h:220:15: error: unknown type name 'target_ulong'
static inline target_ulong kvmppc_configure_v3_mmu(PowerPCCPU *cpu,
^
target/ppc/kvm_ppc.h:286:38: error: unknown type name 'ppc_hash_pte64_t'
static inline void kvmppc_read_hptes(ppc_hash_pte64_t *hptes,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221213123550.39302-2-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some SDHCI IP can be synthetized in various endianness:
https://github.com/u-boot/u-boot/blob/v2021.04/doc/README.fsl-esdhc
- CONFIG_SYS_FSL_ESDHC_BE
ESDHC IP is in big-endian mode. Accessing ESDHC registers can be
determined by ESDHC IP's endian mode or processor's endian mode.
Our current implementation is little-endian. In order to support
big endianness:
- Rename current MemoryRegionOps as sdhci_mmio_le_ops ('le')
- Add an 'endianness' property to SDHCIState (default little endian)
- Set the 'io_ops' field in realize() after checking the property
- Add the sdhci_mmio_be_ops (big-endian) MemoryRegionOps.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221101222934.52444-3-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The maintainer is no longer being paid to maintain these components. All
maintainership work is being done in his personal time since the middle
of the 7.2 development cycle.
Change the status of PPC KVM CPUs, PPC TCG CPUs and the pSeries machine
to 'Odd Fixes', reflecting that the maintainer no longer has exclusive
time to dedicate to them. It'll also (hopefully) keep expectations under
check when/if these components are used in a customer product.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20221117153218.182835-1-danielhb413@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
virtio,pc,pci: features, cleanups, fixes
make TCO watchdog work by default
part of generic vdpa support
asid interrupt for vhost-vdpa
added flex bus port DVSEC for cxl
misc fixes, cleanups, documentation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 21 Dec 2022 12:32:36 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (41 commits)
contrib/vhost-user-blk: Replace lseek64 with lseek
libvhost-user: Switch to unsigned int for inuse field in struct VuVirtq
hw/virtio: Extract QMP related code virtio-qmp.c
hw/virtio: Extract config read/write accessors to virtio-config-io.c
hw/virtio: Constify qmp_virtio_feature_map_t[]
hw/virtio: Guard and restrict scope of qmp_virtio_feature_map_t[]
hw/virtio: Rename virtio_ss[] -> specific_virtio_ss[]
hw/virtio: Add missing "hw/core/cpu.h" include
hw/cxl/device: Add Flex Bus Port DVSEC
hw/acpi: Rename tco.c -> ich9_tco.c
acpi/tests/avocado/bits: add mformat as one of the dependencies
docs/acpi/bits: document BITS_DEBUG environment variable
pci: drop redundant PCIDeviceClass::is_bridge field
remove DEC 21154 PCI bridge
vhost: fix vq dirty bitmap syncing when vIOMMU is enabled
acpi/tests/avocado/bits: add SPDX license identifiers for bios bits tests
include/hw: attempt to document VirtIO feature variables
vhost-user: send set log base message only once
vdpa: always start CVQ in SVQ mode if possible
vdpa: add shadow_data to vhost_vdpa
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use interval trees for user-only vma mappings.
Assorted cleanups to page locking.
# gpg: Signature made Wed 21 Dec 2022 05:00:30 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20221220' of https://gitlab.com/rth7680/qemu:
accel/tcg: Restrict page_collection structure to system TB maintainance
accel/tcg: Factor tb_invalidate_phys_range_fast() out
accel/tcg: Rename tb_invalidate_phys_page_fast{,__locked}()
accel/tcg: Remove trace events from trace-root.h
accel/tcg: Restrict cpu_io_recompile() to system emulation
accel/tcg: Move remainder of page locking to tb-maint.c
accel/tcg: Move PageDesc tree into tb-maint.c for system
accel/tcg: Use interval tree for user-only page tracking
accel/tcg: Move page_{get,set}_flags to user-exec.c
accel/tcg: Drop PAGE_RESERVED for CONFIG_BSD
accel/tcg: Use interval tree for TARGET_PAGE_DATA_SIZE
accel/tcg: Use interval tree for TBs in user-only mode
accel/tcg: Rename page_flush_tb
util: Add interval-tree.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit da0bd74434 we refactored bdrv_drain_all_begin() to pull out
the non-polling part into bdrv_drain_all_begin_nopoll(). This change
broke record-and-replay, because the "return early if replay enabled"
check is now in the sub-function bdrv_drain_all_begin_nopoll(), and
so it only causes us to return from that function, and not from the
calling bdrv_drain_all_begin().
Fix the regression by checking whether replay is enabled in both
functions.
The breakage and fix can be tested via 'make check-avocado': the
tests/avocado/reverse_debugging.py:ReverseDebugging_X86_64.test_x86_64_pc
tests/avocado/reverse_debugging.py:ReverseDebugging_AArch64.test_aarch64_virt
tests were both broken by this.
Fixes: da0bd74434 ("block: Factor out bdrv_drain_all_begin_nopoll()")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Fabiano Rosas <farosas@suse.de>
Message-id: 20221220174638.2156308-1-peter.maydell@linaro.org
It seems there is no need to keep the inuse field signed and end up with
compiler warnings for sign-compare.
CC libvhost-user.o
libvhost-user.c: In function ‘vu_queue_pop’:
libvhost-user.c:2763:19: error: comparison of integer expressions of different signedness: ‘int’ and ‘unsigned int’ [-Werror=sign-compare]
2763 | if (vq->inuse >= vq->vring.num) {
| ^~
libvhost-user.c: In function ‘vu_queue_rewind’:
libvhost-user.c:2808:13: error: comparison of integer expressions of different signedness: ‘unsigned int’ and ‘int’ [-Werror=sign-compare]
2808 | if (num > vq->inuse) {
| ^
Instead of casting the comparision to unsigned int, just make the inuse
field unsigned int in the fist place.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Message-Id: <20221219175337.377435-8-marcel@holtmann.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The monitor decoders are the only functions using the CONFIG_xxx
definitions declared in the target specific CONFIG_DEVICES header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-7-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <a class="moz-txt-link-rfc2396E" href="mailto:philmd@linaro.org"><philmd@linaro.org></a>
virtio.c uses target_words_bigendian() which is declared in
"hw/core/cpu.h". Add the missing header to avoid when refactoring:
hw/virtio/virtio.c:2451:9: error: implicit declaration of function 'target_words_bigendian' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (target_words_bigendian()) {
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-2-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
mformat is needed by grub-mkrescue and hence, add this as one of the
dependencies to run bits tests. This avoids errors such as the following:
/var/tmp/acpi-bits-wju6tqoa.tmp/grub-inst-x86_64-efi/bin/grub-mkrescue: 360: mformat: not found
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20221203132407.34539-1-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Code has not been used practically since its inception (2004)
f2aa58c6f4 UniNorth PCI bridge support
or maybe even earlier, but it was consuming contributors time
as QEMU was being rewritten.
Drop it for now. Whomever would like to actually
use the thing, can make sure it actually works/reintroduce
it back when there is a user.
PS:
I've stumbled upon this when replacing PCIDeviceClass::is_bridge
field with QOM cast to PCI_BRIDGE type. Unused DEC 21154
was the only one trying to use the field with plain PCIDevice.
It's not worth keeping the field around for the sake of the code
that was commented out 'forever'.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221129101341.185621-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When vIOMMU is enabled, the vq->used_phys is actually the IOVA not
GPA. So we need to translate it to GPA before the syncing otherwise we
may hit the following crash since IOVA could be out of the scope of
the GPA log size. This could be noted when using virtio-IOMMU with
vhost using 1G memory.
Fixes: c471ad0e9b ("vhost_net: device IOTLB support")
Cc: qemu-stable@nongnu.org
Tested-by: Lei Yang <leiyang@redhat.com>
Reported-by: Yalan Zhang <yalzhang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221216033552.77087-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The memory listener that thells the device how to convert GPA to qemu's
va is registered against CVQ vhost_vdpa. memory listener translations
are always ASID 0, CVQ ones are ASID 1 if supported.
Let's tell the listener if it needs to register them on iova tree or
not.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-12-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CVQ can be shadowed two ways:
- Device has x-svq=on parameter (current way)
- The device can isolate CVQ in its own vq group
QEMU needs to check for the second condition dynamically, because CVQ
index is not known before the driver ack the features. Since this is
dynamic, the CVQ isolation could vary with different conditions, making
it possible to go from "not isolated group" to "isolated".
Saving the cmdline parameter in an extra field so we never disable CVQ
SVQ in case the device was started with x-svq cmdline.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-11-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So the caller can choose which ASID is destined.
No need to update the batch functions as they will always be called from
memory listener updates at the moment. Memory listener updates will
always update ASID 0, as it's the passthrough ASID.
All vhost devices's ASID are 0 at this moment.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-10-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SVQ may run or not in a device depending on runtime conditions (for
example, if the device can move CVQ to its own group or not).
Allocate the SVQ array unconditionally at startup, since its hard to
move this allocation elsewhere.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-9-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The next patches will start control SVQ if possible. However, we don't
know if that will be possible at qemu boot anymore.
Since the moved checks will be already evaluated at net/ to know if it
is ok to shadow CVQ, move them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-8-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since we don't know if we will use SVQ at qemu initialization, let's
allocate iova_tree only if needed. To do so, accept it at SVQ start, not
at initialization.
This will avoid to create it if the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-5-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The next patches will start control SVQ if possible. However, we don't
know if that will be possible at qemu boot anymore.
Delay device file descriptors until we know it at device start. This
will avoid to create them if the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By the end of this series CVQ is shadowed as long as the features
support it.
Since we don't know at the beginning of qemu running if this is
supported, move the event notifier handler setting to the start of the
SVQ, instead of the start of qemu run. This will avoid to create them if
the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This function used to trust in v->shadow_vqs != NULL to know if it must
start svq or not.
This is not going to be valid anymore, as qemu is going to allocate svq
array unconditionally (but it will only start them conditionally).
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An 'ICH9-LPC.enable_tco' property has been exposed for a
very long time, but attempts to set it have never been
honoured.
Originally, any user provided 'enable_tco' value was force
replaced by a value passed from the machine type setup
code that was determine by machine type compat properties.
commit d6b304ba92
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:10 2016 -0200
machine: Remove no_tco field
The field is always set to zero, so it is not necessary anymore.
After legacy Q35 machine types were deleted in:
commit 86165b499e
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:09 2016 -0200
q35: Remove old machine versions
the machine type code ended up just unconditionally passing
'true', all the time, so this was further simplified in
commit d6b304ba92
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:10 2016 -0200
machine: Remove no_tco field
The field is always set to zero, so it is not necessary anymore.
commit 18d6abae3e
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:11 2016 -0200
ich9: Remove enable_tco arguments from init functions
The enable_tco arguments are always true, so they are not needed
anymore.
Leaving the ich9_pm_init to just force set 'enable_tco' to true.
This still overrides any user specified property. The initialization
of property defaults should be done when properties are first
registered, rather than during object construction.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-6-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The TCO watchdog implementation default behaviour from POV of the
guest OS relies on the initial values for two I/O ports:
* TCO1_CNT == 0x0
Since bit 11 (TCO Timer Halt) is clear, the watchdog state
is considered to be initially running
* GCS == 0x20
Since bit 5 (No Reboot) is set, the watchdog will not trigger
when the timer expires
This is a safe default, because the No Reboot bit will prevent the
watchdog from triggering if the guest OS is unaware of its existance,
or is slow in configuring it. When a Linux guest initializes the TCO
watchdog, it will attempt to clear the "No Reboot" flag, and read the
value back. If the clear was honoured, the driver will treat this as
an indicator that the watchdog is functional and create the guest
watchdog device.
QEMU implements a second "no reboot" flag, however, via pin straps
which overrides the behaviour of the guest controlled "no reboot"
flag:
commit 5add35bec1
Author: Paulo Alcantara <pcacjr@gmail.com>
Date: Sun Jun 28 14:58:58 2015 -0300
ich9: implement strap SPKR pin logic
This second 'noreboot' pin was defaulted to high, which also inhibits
triggering of the requested watchdog actions, unless QEMU is launched
with the magic flag "-global ICH9-LPC.noreboot=false".
This is a bad default as we are exposing a watchdog to every guest OS
using the q35 machine type, but preventing it from actually doing what
it is designed to do. What is worse is that the guest OS and its apps
have no way to know that the watchdog is never going to fire, due to
this second 'noreboot' pin.
If a guest OS had no watchdog device at all, then apps whose operation
and/or data integrity relies on a watchdog can refuse to launch, and
alert the administrator of the problematic deployment. With Q35 machines
unconditionally exposing a watchdog though, apps will think their
deployment is correct but in fact have no protection at all.
This patch flips the default of the second 'no reboot' flag, so that
configured watchdog actions will be honoured out of the box for the
7.2 Q35 machine type onwards, if the guest enables use of the watchdog.
See also related bug reports
https://bugzilla.redhat.com/show_bug.cgi?id=2080207https://bugzilla.redhat.com/show_bug.cgi?id=2136889https://bugzilla.redhat.com/show_bug.cgi?id=2137346
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-5-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only the system emulation part of TB maintainance uses the
page_collection structure. Restrict its declaration (and the
functions requiring it) to tb-maint.c.
Convert the 'len' argument of tb_invalidate_phys_page_fast__locked()
from signed to unsigned.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20221209093649.43738-6-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The only thing that still touches PageDesc in translate-all.c
are some locking routines related to tb-maint.c which have not
yet been moved. Do so now.
Move some code up in tb-maint.c as well, to untangle the maze
of ifdefs, and allow a sensible final ordering.
Move some declarations from exec/translate-all.h to internal.h,
as they are only used within accel/tcg/.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that PageDesc is not used for user-only, and for system
it is only used for tb maintenance, move the implementation
into tb-main.c appropriately ifdefed.
We have not yet eliminated all references to PageDesc for
user-only, so retain a typedef to the structure without definition.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This page tracking implementation is specific to user-only,
since the system softmmu version is in cputlb.c. Move it
out of translate-all.c to user-exec.c.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Make bsd-user match linux-user in not marking host pages
as reserved. This isn't especially effective anyway, as
it doesn't take into account any heap memory that qemu
may allocate after startup.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Tested-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Continue weaning user-only away from PageDesc.
Use an interval tree to record target data.
Chunk the data, to minimize allocation overhead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Begin weaning user-only away from PageDesc.
Since, for user-only, all TB (and page) manipulation is done with
a single mutex, and there is no virtual/physical discontinuity to
split a TB across discontinuous pages, place all of the TBs into
a single IntervalTree. This makes it trivial to find all of the
TBs intersecting a range.
Retain the existing PageDesc + linked list implementation for
system mode. Move the portion of the implementation that overlaps
the new user-only code behind the common ifdef.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Rename to tb_remove_all, to remove the PageDesc "page" from the name,
and to avoid suggesting a "flush" in the icache sense.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Copy and simplify the Linux kernel's interval_tree_generic.h,
instantiating for uint64_t.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
qga-pull-2022-12-20
# gpg: Signature made Tue 20 Dec 2022 13:57:59 GMT
# gpg: using RSA key C2C2C109EA43C63C1423EB84EF5D5E8161BA84E7
# gpg: Good signature from "Kostiantyn Kostiuk (Upstream PR sign) <kkostiuk@redhat.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: C2C2 C109 EA43 C63C 1423 EB84 EF5D 5E81 61BA 84E7
* tag 'qga-pull-2022-12-20' of github.com:kostyanf14/qemu:
qga-win: choose the right libpcre version to include in MSI package
qga: map GLib log levels to system levels
qga-win: add logging to Windows event log
qga: Add initial OpenBSD and NetBSD support
qga:/qga-win: skip getting pci info for USB disks
qga:/qga-win: adding a empty PCI address creation function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch translates GLib-specific log levels to system ones, so that
they may be used by both *nix syslog() (as a "priority" argument) and
Windows ReportEvent() (as a "wType" argument).
Currently the only codepath to write to "syslog" domain is slog()
function. However, this patch allows the interface to be extended.
Note that since slog() is using G_LOG_LEVEL_INFO level, its behaviour
doesn't change.
Originally-by: Yuri Pudgorodskiy <yur@virtuozzo.com>
Signed-off-by: Andrey Drobyshev <andrey.drobyshev@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Tested-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
The fid instruction (Floating-Point Identify) puts the FPU model and
revision into the Status Register. Since those values shouldn't be 0,
store values there which a PCX-L2 (for 32-bit) or a PCX-W2 (for 64-bit)
would return. Noticed while trying to install MPE/iX.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Qemu currently emulates a 32-bit CPU only, and crashes with this error
when it faces a 64-bit load (e.g. "ldd 0(r26),r0") or a 64-bit store
(e.g. "std r26,0(r26)") instruction in the guest:
ERROR:../qemu/tcg/tcg-op.c:2822:tcg_canonicalize_memop: code should not be reached
Add checks for 64-bit sizes and generate an illegal instruction
exception if necessary.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Monitor patches for 2022-12-19
# gpg: Signature made Mon 19 Dec 2022 15:23:44 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-monitor-2022-12-19' of https://repo.or.cz/qemu/armbru:
pci: Reject pcie_aer_inject_error -c with symbolic error status
pci: Improve do_pcie_aer_inject_error()'s error messages
pci: Rename hmp_pcie_aer_inject_error()'s local variable @err
pci: Inline do_pcie_aer_inject_error() into its only caller
pci: Move HMP command from hw/pci/pcie_aer.c to pci-hmp-cmds.c
pci: Fix silent truncation of pcie_aer_inject_error argument
pci: Move pcibus_dev_print() to pci-hmp-cmds.c
pci: Deduplicate get_class_desc()
pci: Build hw/pci/pci-hmp-cmds.c only when CONFIG_PCI
pci: Make query-pci stub consistent with the real one
pci: Move HMP commands from monitor/ to new hw/pci/pci-hmp-cmds.c
pci: Move QMP commands to new hw/pci/pci-qmp-cmds.c
pci: Clean up a few things checkpatch.pl would flag later on
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PCI AER error status is 32 bit. The HMP command supports both
symbolic and numeric error status: anything that isn't a known
symbolic value is parsed as number with strtol(). Issues:
* Empty argument yields value zero.
* Range errors from strtol() are ignored, value is UINT32_MAX.
* Values not representable in uint32_t are silently truncated.
Fix to reject such input by switching to strtoui().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-9-armbru@redhat.com>
We compile pci-hmp-cmds.c always, but pci-qmp-cmds.c only when
CONFIG_PCI. hw/pci/pci-stub.c keeps the linker happy when
!CONFIG_PCI. Build pci-hmp-cmds.c that way, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-6-armbru@redhat.com>
QMP query-pci and HMP info pci can behave differently when there are
no PCI devices. They can report nothing, like this:
qemu-system-aarch64 -S -M spitz -display none -monitor stdio
QEMU 7.1.91 monitor - type 'help' for more information
(qemu) info pci
Or they can fail, like this:
qemu-system-microblaze -M petalogix-s3adsp1800 -display none -monitor stdio
QEMU 7.1.91 monitor - type 'help' for more information
(qemu) info pci
PCI devices not supported
They fail when none of the target's machines supports PCI, i.e. when
we're using qmp_query_pci() from hw/pci/pci-stub.c.
The error is not useful, and reporting nothing makes sense, so do that
in pci-stub.c, too.
Now qmp_query_pci() can't fail anymore. Drop the dead error handling
from hmp_info_pci().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221201121133.3813857-5-armbru@redhat.com>
1)
Performance improvement
Add pkt and insn to DisasContext
Many functions need information from all 3 structures, so merge
them together.
2)
Bug fix
Fix predicated assignment to .tmp and .cur
3)
Performance improvement
Add overrides for S2_asr_r_r_sat/S2_asl_r_r_sat
These functions will not be handled by idef-parser
4-11)
The final 8 patches improve change-of-flow handling.
Currently, we set the PC to a new address before exiting a TB. The
ultimate goal is to use direct block chaining. However, several steps
are needed along the way.
4)
When a packet has more than one change-of-flow (COF) instruction, only
the first one taken is considered. The runtime bookkeeping is only
needed when there is more than one COF instruction in a packet.
5, 6)
Remove PC and next_PC from the runtime state and always use a
translation-time constant. Note that next_PC is used by call instructions
to set LR and by conditional COF instructions to set the fall-through
address.
7, 8, 9)
Add helper overrides for COF instructions. In particular, we must
distinguish those that use a PC-relative address for the destination.
These are candidates for direct block chaining later.
10)
Use direct block chaining for packets that have a single PC-relative
COF instruction. Instead of generating the code while processing the
instruction, we record the effect in DisasContext and generate the code
during gen_end_tb.
11)
Use direct block chaining for tight loops. We look for TBs that end
with an endloop0 that will branch back to the TB start address.
12-21)
Instruction definition parser (idef-parser) from rev.ng
Parses the instruction semantics and generates TCG
# gpg: Signature made Fri 16 Dec 2022 20:41:53 GMT
# gpg: using RSA key 3635C788CE62B91FD4C59AB47B0244FB12DE4422
# gpg: Good signature from "Taylor Simpson (Rock on) <tsimpson@quicinc.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3635 C788 CE62 B91F D4C5 9AB4 7B02 44FB 12DE 4422
* tag 'pull-hex-20221216-1' of https://github.com/quic/qemu: (21 commits)
target/hexagon: import additional tests
target/hexagon: call idef-parser functions
target/hexagon: import parser for idef-parser
target/hexagon: import lexer for idef-parser
target/hexagon: prepare input for the idef-parser
target/hexagon: introduce new helper functions
target/hexagon: make helper functions non-static
target/hexagon: make slot number an unsigned
target/hexagon: import README for idef-parser
target/hexagon: update MAINTAINERS for idef-parser
Hexagon (target/hexagon) Use direct block chaining for tight loops
Hexagon (target/hexagon) Use direct block chaining for direct jump/branch
Hexagon (target/hexagon) Add overrides for various forms of jump
Hexagon (target/hexagon) Add overrides for compound compare and jump
Hexagon (target/hexagon) Add overrides for direct call instructions
Hexagon (target/hexagon) Remove next_PC from runtime state
Hexagon (target/hexagon) Remove PC from the runtime state
Hexagon (target/hexagon) Only use branch_taken when packet has multi cof
Hexagon (target/hexagon) Add overrides for S2_asr_r_r_sat/S2_asl_r_r_sat
Hexagon (target/hexagon) Fix predicated assignment to .tmp and .cur
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add cfi01 pflash device
# gpg: Signature made Thu 15 Dec 2022 07:49:03 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20221215' of https://gitlab.com/gaosong/qemu:
hw/loongarch/virt: Add cfi01 pflash device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce infrastructure necessary to produce a file suitable for being
parsed by the idef-parser. A build option is also added to fully disable
the output of idef-parser, which is useful for debugging.
Signed-off-by: Alessandro Di Federico <ale@rev.ng>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20220923173831.227551-8-anjo@rev.ng>
These helpers will be employed by the idef-parser generated code, to
correctly implement instruction semantics. "Helper" functions, in the
context of this patch, refers to functions which provide a manual TCG
implementation of certain features.
Signed-off-by: Alessandro Di Federico <ale@rev.ng>
Signed-off-by: Niccolò Izzo <nizzo@rev.ng>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20220923173831.227551-6-anjo@rev.ng>
Make certain helper functions non-static, making them available outside
genptr.c. These functions are required by code generated by the
idef-parser.
This commit also makes some functions in op_helper.c non-static in order
to avoid having them marked as unused when using the idef-parser
generated code.
Signed-off-by: Alessandro Di Federico <ale@rev.ng>
Signed-off-by: Paolo Montesel <babush@rev.ng>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20220923173831.227551-5-anjo@rev.ng>
Direct block chaining is documented here
https://qemu.readthedocs.io/en/latest/devel/tcg.html#direct-block-chaining
Hexagon inner loops end with the endloop0 instruction
To go back to the beginning of the loop, this instructions writes to PC
from register SA0 (start address 0). To use direct block chaining, we
have to assign PC with a constant value. So, we specialize the code
generation when the start of the translation block is equal to SA0.
When this is the case, we defer the compare/branch from endloop0 to
gen_end_tb. When this is done, we can assign the start address of the TB
to PC.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221108162906.3166-12-tsimpson@quicinc.com>
Direct block chaining is documented here
https://qemu.readthedocs.io/en/latest/devel/tcg.html#direct-block-chaining
Recall that Hexagon allows packets with multiple jumps where only the
first one with a true predicate will actually jump. We can use
tcg_gen_goto_tb/tcg_gen_exit_tb when the packet contains a single
PC-relative branch or jump. If not, we use tcg_gen_lookup_and_goto_ptr.
We add the following to DisasContext in order to delay the branching
until the end of packet commit (in gen_end_tb)
branch_cond
The TCGCond condition under which the branch is taken
When branch_cond == TCG_COND_NEVER, there isn't a single
direct branch in this packet.
When branch_cond != TCG_COND_ALWAYS, the value is in
hex_branch_taken
branch_dest
The destination of the branch
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221108162906.3166-11-tsimpson@quicinc.com>
When a packet has more than one change-of-flow instruction, only the first
one to branch is considered. We use the branch_taken variable to keep
track of this.
However, when there is a single cof instruction, we don't need the same
amount of bookkeeping.
We add the pkt_has_multi_cof member to the Packet structure, and pass this
information to the needed functions.
When there is a generated helper function with cof, the generator will
pass this pkt_has_multi_cof as a runtime value.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221108162906.3166-5-tsimpson@quicinc.com>
Here are example instructions with a predicated .tmp/.cur assignment
if (p1) v12.tmp = vmem(r7 + #0)
if (p0) v12.cur = vmem(r9 + #0)
The .tmp/.cur indicates that references to v12 in the same packet
take the result of the load. However, when the predicate is false,
the value at the start of the packet should be used. After the packet
commits, the .tmp value is dropped, but the .cur value is maintained.
To fix this bug, we preload the original value from the HVX register
into the temporary used for the result.
Test cases added to tests/tcg/hexagon/hvx_misc.c
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Co-authored-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Signed-off-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221108162906.3166-3-tsimpson@quicinc.com>
This enables us to reduce the number of parameters to many functions
In particular, the generated functions previously took all 3 as arguments
Not only does this simplify the code, it improves the translation time
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20221108162906.3166-2-tsimpson@quicinc.com>
The realize method for the TYPE_ICS class uses qemu_register_reset()
to register a reset handler, as a workaround for the fact that
currently objects which directly inherit from TYPE_DEVICE don't get
automatically reset. However, the reset function directly calls
ics_reset(), which is the function that implements the legacy reset
method. This means that only the parent class's data gets reset, and
a subclass which also needs to handle reset, like TYPE_PHB3_MSI, has
to register its own reset function.
Make the TYPE_ICS reset function call device_cold_reset() instead:
this will handle reset for both the parent class and the subclass,
and will work whether the classes are using legacy reset or 3-phase
reset. This allows us to remove the reset function that the subclass
currently has to set up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-6-peter.maydell@linaro.org
Convert the TYPE_CXL_ROOT_PORT and TYPE_PNV_PHB_ROOT_PORT classes to
3-phase reset, so they don't need to use the deprecated
device_class_set_parent_reset() function any more.
We have to do both in the same commit, because they keep the
parent_reset field in their common parent class's class struct.
Note that pnv_phb_root_port_class_init() was pointlessly setting
dc->reset twice, once by calling device_class_set_parent_reset()
and once directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-5-peter.maydell@linaro.org
Convert the TYPE_VIRTIO_VGA_BASE class to 3-phase reset, so we
don't need to use device_class_set_parent_reset() any more.
Note that this is an abstract class itself; none of the subclasses
override its reset method.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-3-peter.maydell@linaro.org
Convert the child classes TYPE_PS2_KBD_DEVICE and
TYPE_PS2_MOUSE_DEVICE to the 3-phase reset system. This allows us to
stop using the old device_class_set_parent_reset() function.
We don't need to register an 'exit' phase function for the
subclasses, because they have no work to do in that phase. Passing
NULL to resettable_class_set_parent_phases() will result in the
parent class method being called for that phase, so we don't need to
register a function purely to chain to the parent 'exit' phase
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109170009.3498451-3-peter.maydell@linaro.org
Convert the parent class TYPE_PS2_DEVICE to 3-phase reset. Note that
we need an 'exit' phase function as well as the usual 'hold' phase
function, because changing outbound IRQ line state is only permitted
in 'exit'. (Strictly speaking it's not supposed to be done in a
legacy reset handler either, but you can often get away with it.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109170009.3498451-2-peter.maydell@linaro.org
The device_legacy_reset() function is now not used anywhere, so we
can remove the implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the qdev_reset_all() and qbus_reset_all() functions, now we
have moved all the callers over to the new device_cold_reset() and
bus_cold_reset() functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The legacy function qdev_reset_all() performs a recursive reset,
starting from a qdev. However, it does not permit any of the devices
in the tree to use three-phase reset, because device reset goes
through the device_legacy_reset() function that only calls the single
DeviceClass::reset method.
Switch to using the device_cold_reset() function instead. This also
performs a recursive reset, where first the children are reset and
then finally the parent, but it uses the new (...in 2020...)
Resettable mechanism, which supports both the old style single-reset
method and also the new 3-phase reset handling.
This commit changes the five remaining uses of this function.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g' hw/i386/xen/xen_platform.c hw/input/adb.c hw/remote/vfio-user-obj.c hw/s390x/s390-virtio-ccw.c hw/usb/dev-uas.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the vmbus code we currently use the legacy functions
qdev_reset_all() and qbus_reset_all(). These perform a recursive
reset, starting from either a qbus or a qdev. However they do not
permit any of the devices in the tree to use three-phase reset,
because device reset goes through the device_legacy_reset() function
that only calls the single DeviceClass::reset method.
Switch to using the device_cold_reset() and bus_cold_reset()
functions. These also perform a recursive reset, where first the
children are reset and then finally the parent, but they use the new
(...in 2020...) Resettable mechanism, which supports both the old
style single-reset method and also the new 3-phase reset handling.
This should be a no-behaviour-change commit which just reduces the
use of a deprecated API.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g;s/qbus_reset_all/bus_cold_reset/g' hw/hyperv/*.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the PCI subsystem we currently use the legacy function
qdev_reset_all() and qbus_reset_all(). These perform a recursive
reset, starting from either a qbus or a qdev. However they do not
permit any of the devices in the tree to use three-phase reset,
because device reset goes through the device_legacy_reset() function
that only calls the single DeviceClass::reset method.
Switch to using the device_cold_reset() and bus_cold_reset()
functions. These also perform a recursive reset, where first the
children are reset and then finally the parent, but they use the new
(...in 2020...) Resettable mechanism, which supports both the old
style single-reset method and also the new 3-phase reset handling.
This should be a no-behaviour-change commit which just reduces the
use of a deprecated API.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g;s/qbus_reset_all/bus_cold_reset/g' hw/pci/*.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The semantic difference between the deprecated device_legacy_reset()
function and the newer device_cold_reset() function is that the new
function resets both the device itself and any qbuses it owns,
whereas the legacy function resets just the device itself and nothing
else.
In s390-pci-inst.c we use device_legacy_reset() to reset an
S390PCIBusDevice. This device doesn't have any child qbuses, so the
functions do the same thing and we can stop using the deprecated one.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Block layer patches
- Code cleanups around block graph modification
- Simplify drain
- coroutine_fn correctness fixes, including splitting generated
coroutine wrappers into co_wrapper (to be called only from
non-coroutine context) and co_wrapper_mixed (both coroutine and
non-coroutine context)
- Introduce a block graph rwlock
# gpg: Signature made Thu 15 Dec 2022 15:08:34 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (50 commits)
block: GRAPH_RDLOCK for functions only called by co_wrappers
block: use co_wrapper_mixed_bdrv_rdlock in functions taking the rdlock
block-coroutine-wrapper.py: introduce annotations that take the graph rdlock
Mark assert_bdrv_graph_readable/writable() GRAPH_RD/WRLOCK
graph-lock: TSA annotations for lock/unlock functions
block: assert that graph read and writes are performed correctly
block: remove unnecessary assert_bdrv_graph_writable()
block: wrlock in bdrv_replace_child_noperm
block: Fix locking in external_snapshot_prepare()
test-bdrv-drain: Fix incorrrect drain assumptions
clang-tsa: Add macros for shared locks
clang-tsa: Add TSA_ASSERT() macro
Import clang-tsa.h
async: Register/unregister aiocontext in graph lock list
graph-lock: Implement guard macros
graph-lock: Introduce a lock to protect block graph operations
block: Factor out bdrv_drain_all_begin_nopoll()
block/dirty-bitmap: convert coroutine-only functions to co_wrapper
block: convert bdrv_create to co_wrapper
block-coroutine-wrapper.py: support also basic return types
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* s390x PCI fixes and improvements (for the ISM device)
* Fix emulated MVCP and MVCS s390x instructions
* Clean-ups for the e1000e qtest
* Enable qtests on Windows
* Update FreeBSD CI to version 12.4
* Check --disable-tcg for ppc64 in the CI
* Improve scripts/make-releases a little bit
* Many other misc small clean-ups and fixes here and there
# gpg: Signature made Thu 15 Dec 2022 15:05:44 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-12-15' of https://gitlab.com/thuth/qemu: (23 commits)
tests/qtest/vhost-user-blk-test: don't abort all qtests on missing envar
.gitlab/issue_templates: Move suggestions into comments
gitlab-ci: Check building ppc64 without TCG
FreeBSD: Upgrade to 12.4 release
tests/qtest: Enable qtest build on Windows
.gitlab-ci.d/windows.yml: Exclude qTests from 64-bit CI job for now
.gitlab-ci.d/windows.yml: Keep 64-bit and 32-bit build scripts consistent
.gitlab-ci.d/windows.yml: Unify the prerequisite packages
tests/qtest/libqos/e1000e: Correctly group register accesses
tests/qtest/e1000e-test: De-duplicate constants
tests/qtest/libqos/e1000e: Remove "other" interrupts
hw: Include the VMWare devices only in the x86 targets
MAINTAINERS: Add documentation files to the corresponding sections
util/oslib-win32: Remove obsolete reference to g_poll code
util/qemu-config: Fix "query-command-line-options" to provide the right values
scripts/make-release: Only clone single branches to speed up the script
scripts/make-release: Add a simple help text for the script
monitor/misc: Remove superfluous include statements
target/s390x: The MVCP and MVCS instructions are not privileged
target/s390x/tcg/mem_helper: Test the right bits in psw_key_valid()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When building with --disable-tcg on Darwin we get:
target/arm/cpu.c:725:16: error: incomplete definition of type 'struct TCGCPUOps'
cc->tcg_ops->do_interrupt(cs);
~~~~~~~~~~~^
Commit 083afd18a9 ("target/arm: Restrict cpu_exec_interrupt()
handler to sysemu") limited this block to system emulation,
but neglected to also limit it to TCG.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-id: 20221209110823.59495-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The header target/arm/kvm-consts.h checks CONFIG_KVM which is marked as
poisoned in common code, so the files that include this header have to
be added to specific_ss and recompiled for each, qemu-system-arm and
qemu-system-aarch64. However, since the kvm headers are only optionally
used in kvm-constants.h for some sanity checks, we can additionally
check the NEED_CPU_H macro first to avoid the poisoned CONFIG_KVM macro,
so kvm-constants.h can also be used from "common" files (without the
sanity checks - which should be OK since they are still done from other
target-specific files instead). This way, and by adjusting some other
include statements in the related files here and there, we can move some
files from specific_ss into softmmu_ss, so that they only need to be
compiled once during the build process.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221202154023.293614-1-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The generated coroutine wrappers already take care to take the lock in
the non-coroutine path, and assume that the lock is already taken in the
coroutine path.
The only thing we need to do for the wrapped function is adding the
GRAPH_RDLOCK annotation. Doing so also allows us to mark the
corresponding callbacks in BlockDriver as GRAPH_RDLOCK_PTR.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-19-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Take the rdlock already, before we add the assertions.
All these functions either read the graph recursively, or call
BlockDriver callbacks that will eventually need to be protected by the
graph rdlock.
Do it now to all functions together, because many of these recursively
call each other.
For example, bdrv_co_truncate calls BlockDriver->bdrv_co_truncate, and
some driver callbacks implement their own .bdrv_co_truncate by calling
bdrv_flush inside. So if bdrv_flush asserts but bdrv_truncate does not
take the rdlock yet, the assertion will always fail.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-18-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add co_wrapper_bdrv_rdlock and co_wrapper_mixed_bdrv_rdlock option to
the block-coroutine-wrapper.py script.
This "_bdrv_rdlock" option takes and releases the graph rdlock when a
coroutine function is created.
This means that when used together with "_mixed", the function marked
with co_wrapper_mixed_bdrv_rdlock will support both coroutine and
non-coroutine case, and in the latter case it will create a coroutine
that takes and releases the rdlock. When called from a coroutine, the
caller must already hold the graph lock.
Example:
void co_wrapper_mixed_bdrv_rdlock bdrv_f1();
Becomes
static void bdrv_co_enter_f1()
{
bdrv_graph_co_rdlock();
bdrv_co_function();
bdrv_graph_co_rdunlock();
}
void bdrv_f1()
{
if (qemu_in_coroutine) {
assume_graph_lock();
bdrv_co_function();
} else {
qemu_co_enter(bdrv_co_enter_f1);
...
}
}
When used alone, the function will not work in coroutine context, and
when called in non-coroutine context it will create a new coroutine that
takes care of taking and releasing the rdlock automatically.
Example:
void co_wrapper_bdrv_rdlock bdrv_f1();
Becomes
static void bdrv_co_enter_f1()
{
bdrv_graph_co_rdlock();
bdrv_co_function();
bdrv_graph_co_rdunlock();
}
void bdrv_f1()
{
assert(!qemu_in_coroutine());
qemu_co_enter(bdrv_co_enter_f1);
...
}
About their usage:
- co_wrapper does not take the rdlock, so it can be used also outside
the block layer.
- co_wrapper_mixed will be used by many blk_* functions, since the
coroutine function needs to call blk_wait_while_drained() and
the rdlock *must* be taken afterwards, otherwise it's a deadlock.
In the future this annotation will go away, and blk_* will use
co_wrapper directly.
- co_wrapper_bdrv_rdlock will be used by BlockDriver callbacks, ideally
by all of them in the future.
- co_wrapper_mixed_bdrv_rdlock will be used by the remaining functions
that are still called by coroutine and non-coroutine context. In the
future this annotation will go away, as we will split such mixed
functions.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-17-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_img_create() polls internally (when calling bdrv_create(), which is
a co_wrapper), so it can't be called while holding the lock of any
AioContext except the current one without causing deadlocks. Drop the
lock around the call in external_snapshot_prepare().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-11-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The test case assumes that a drain only happens in one specific place
where it drains explicitly. This assumption happened to hold true until
now, but block layer functions may drain interally (any graph
modifications are going to do that through bdrv_graph_wrlock()), so this
is incorrect. Make sure that the test code in .drained_begin only runs
where we actually want it to run.
When scheduling a BH from .drained_begin, we also need to increase the
in_flight counter to make sure that the operation is actually completed
in time before the node that it works on goes away.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-10-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add/remove the AioContext in aio_context_list in graph-lock.c when it is
created/destroyed. This allows using the graph locking operations from
this AioContext.
In order to allow linking util/async.c with binaries that don't include
the block layer, introduce stubs for (un)register_aiocontext().
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-5-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Similar to the implementation in lockable.h, implement macros to
automatically take and release the rdlock.
Create the empty GraphLockable and GraphLockableMainloop structs only to
use it as a type for G_DEFINE_AUTOPTR_CLEANUP_FUNC.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-4-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block layer graph operations are always run under BQL in the main loop.
This is proved by the assertion qemu_in_main_thread() and its wrapper
macro GLOBAL_STATE_CODE.
However, there are also concurrent coroutines running in other iothreads
that always try to traverse the graph. Currently this is protected
(among various other things) by the AioContext lock, but once this is
removed, we need to make sure that reads do not happen while modifying
the graph.
We distinguish between writer (main loop, under BQL) that modifies the
graph, and readers (all other coroutines running in various AioContext),
that go through the graph edges, reading ->parents and->children.
The writer (main loop) has "exclusive" access, so it first waits for any
current read to finish, and then prevents incoming ones from entering
while it has the exclusive access.
The readers (coroutines in multiple AioContext) are free to access the
graph as long the writer is not modifying the graph. In case it is, they
go in a CoQueue and sleep until the writer is done.
If a coroutine changes AioContext, the counter in the original and new
AioContext are left intact, since the writer does not care where the
reader is, but only if there is one.
As a result, some AioContexts might have a negative reader count, to
balance the positive count of the AioContext that took the lock. This
also means that when an AioContext is deleted it may have a nonzero
reader count. In that case we transfer the count to a global shared
counter so that the writer is always aware of all readers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-3-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Provide a separate function that just quiesces the users of a node to
prevent new requests from coming in, but without waiting for the already
in-flight I/O to complete.
This function can be used in contexts where polling is not allowed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221207131838.239125-2-kwolf@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_can_store_new_dirty_bitmap and bdrv_remove_persistent_dirty_bitmap
check if they are running in a coroutine, directly calling the
coroutine callback if it's the case.
Except that no coroutine calls such functions, therefore that check
can be removed, and function creation can be offloaded to
c_w.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-15-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extend the regex to cover also return type, pointers included.
This implies that the value returned by the function cannot be
a simple "int" anymore, but the custom return type.
Therefore remove poll_state->ret and instead use a per-function
custom "ret" field.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-13-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Right now, we take the first parameter of the function to get the
BlockDriverState to pass to bdrv_poll_co(), that internally calls
functions that figure in which aiocontext the coroutine should run.
However, it is useless to pass a bs just to get its own AioContext,
so instead pass it directly, and default to the main loop if no
BlockDriverState is passed as parameter.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-12-eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This new annotation starts just a function wrapper that creates
a new coroutine. It assumes the caller is not a coroutine.
It will be the default annotation to be used in the future.
This is much better as c_w_mixed, because it is clear if the caller
is a coroutine or not, and provides the advantage of automating
the code creation. In the future all c_w_mixed functions will be
substituted by co_wrapper.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-11-eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Call two different functions depending on whether bdrv_create
is in coroutine or not, following the same pattern as
generated_co_wrapper functions.
This allows to also call the coroutine function directly,
without using CreateCo or relying in bdrv_create().
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-8-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These functions end up calling bdrv_create() implemented as generated_co_wrapper
functions.
In addition, they also happen to be always called in coroutine context,
meaning all callers are coroutine_fn.
This means that the g_c_w function will enter the qemu_in_coroutine()
case and eventually suspend (or in other words call qemu_coroutine_yield()).
Therefore we can mark such functions coroutine_fn too.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-6-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Avoid mixing bdrv_* functions with blk_*, so create blk_* counterparts
for bdrv_block_status_above and bdrv_is_allocated_above.
Note that since blk_co_block_status_above only calls the g_c_w function
bdrv_common_block_status_above and is marked as coroutine_fn, call
directly bdrv_co_common_block_status_above() to avoid using a g_c_w.
Same applies to blk_co_is_allocated_above.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-5-eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These functions end up calling bdrv_*() implemented as generated_co_wrapper
functions.
In addition, they also happen to be always called in coroutine context,
meaning all callers are coroutine_fn.
This means that the g_c_w function will enter the qemu_in_coroutine()
case and eventually suspend (or in other words call qemu_coroutine_yield()).
Therefore we can mark such functions coroutine_fn too.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-4-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These functions end up calling bdrv_common_block_status_above(), a
generated_co_wrapper function.
In addition, they also happen to be always called in coroutine context,
meaning all callers are coroutine_fn.
This means that the g_c_w function will enter the qemu_in_coroutine()
case and eventually suspend (or in other words call qemu_coroutine_yield()).
Therefore we can mark such functions coroutine_fn too.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-3-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_common_block_status_above() is a g_c_w, and it is being called by
many "wrapper" functions like bdrv_is_allocated(),
bdrv_is_allocated_above() and bdrv_block_status_above().
Because we want to eventually split the coroutine from non-coroutine
case in g_c_w, create duplicate wrappers that take care of directly
calling the same coroutine functions called in the g_c_w.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221128142337.657646-2-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to make sure that bdrv_replace_child_noperm() doesn't have to
poll any more, get rid of the bdrv_parent_drained_begin_single() call.
This is possible now because we can require that the parent is already
drained through the child in question when the function is called and we
don't call the parent drain callbacks more than once.
The additional drain calls needed in callers cause the test case to run
its code in the drain handler too early (bdrv_attach_child() drains
now), so modify it to only enable the code after the test setup has
completed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221118174110.55183-15-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The next patch adds a parent drain to bdrv_attach_child_common(), which
shouldn't be, but is currently called from coroutines in some cases (e.g.
.bdrv_co_create implementations generally open new nodes). Therefore,
the assertion that we're not in a coroutine doesn't hold true any more.
We could just remove the assertion because there is nothing in the
function that should be in conflict with running in a coroutine, but
just to be on the safe side, we can reverse the caller relationship
between bdrv_do_drained_begin() and bdrv_do_drained_begin_quiesce() so
that the latter also just drops out of coroutine context and we can
still be certain in the future that any drain code doesn't run in
coroutines.
As a nice side effect, the structure of bdrv_do_drained_begin() is now
symmetrical with bdrv_do_drained_end().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221118174110.55183-14-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ignore_bds_parents is now ignored during drain_begin and drain_end, so
we can just remove it there. It is still a valid optimisation for
drain_all in bdrv_drained_poll(), so leave it around there.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221118174110.55183-13-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We only need to call both the BlockDriver's callback and the parent
callbacks when going from undrained to drained or vice versa. A second
drain section doesn't make a difference for the driver or the parent,
they weren't supposed to send new requests before and after the second
drain.
One thing that gets in the way is the 'ignore_bds_parents' parameter in
bdrv_do_drained_begin_quiesce() and bdrv_do_drained_end(): It means that
bdrv_drain_all_begin() increases bs->quiesce_counter, but does not
quiesce the parent through BdrvChildClass callbacks. If an additional
drain section is started now, bs->quiesce_counter will be non-zero, but
we would still need to quiesce the parent through BdrvChildClass in
order to keep things consistent (and unquiesce it on the matching
bdrv_drained_end(), even though the counter would not reach 0 yet as
long as the bdrv_drain_all() section is still active).
Instead of keeping track of this, let's just get rid of the parameter.
It was introduced in commit 6cd5c9d7b2 as an optimisation so that
during bdrv_drain_all(), we wouldn't recursively drain all parents up to
the root for each node, resulting in quadratic complexity. As it happens,
calling the callbacks only once solves the same problem, so as of this
patch, we'll still have O(n) complexity and ignore_bds_parents is not
needed any more.
This patch only ignores the 'ignore_bds_parents' parameter. It will be
removed in a separate patch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-12-kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The subtree drain was introduced in commit b1e1af394d as a way to avoid
graph changes between finding the base node and changing the block graph
as necessary on completion of the image streaming job.
The block graph could change between these two points because
bdrv_set_backing_hd() first drains the parent node, which involved
polling and can do anything.
Subtree draining was an imperfect way to make this less likely (because
with it, fewer callbacks are called during this window). Everyone agreed
that it's not really the right solution, and it was only committed as a
stopgap solution.
This replaces the subtree drain with a solution that simply drains the
parent node before we try to find the base node, and then call a version
of bdrv_set_backing_hd() that doesn't drain, but just asserts that the
parent node is already drained.
This way, any graph changes caused by draining happen before we start
looking at the graph and things stay consistent between finding the base
node and changing the graph.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-10-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of using a subtree drain from the top node (which also drains
child nodes of base that we're not even interested in), use a normal
drain for base, which automatically drains all of the parents, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-9-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_reopen() and friends use subtree drains as a lazy way of covering
all the nodes they touch. Turns out that this lazy way is a lot more
complicated than just draining the nodes individually, even not
accounting for the additional complexity in the drain mechanism itself.
Simplify the code by switching to draining the individual nodes that are
already managed in the BlockReopenQueue anyway.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221118174110.55183-8-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Callers don't agree whether bdrv_reopen_queue_child() should be called
with the AioContext lock held or not. Standardise on holding the lock
(as done by QMP blockdev-reopen and the replication block driver) and
fix bdrv_reopen() to do the same.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20221118174110.55183-7-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drained_end_counter is unused now, nobody changes its value any more. It
can be removed.
In cases where we had two almost identical functions that only differed
in whether the caller passes drained_end_counter, or whether they would
poll for a local drained_end_counter to reach 0, these become a single
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20221118174110.55183-5-kwolf@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Polling during bdrv_drained_end() can be problematic (and in the future,
we may get cases for bdrv_drained_begin() where polling is forbidden,
and we don't care about already in-flight requests, but just want to
prevent new requests from arriving).
The .bdrv_drained_begin/end callbacks running in a coroutine is the only
reason why we have to do this polling, so make them non-coroutine
callbacks again. None of the callers actually yield any more.
This means that bdrv_drained_end() effectively doesn't poll any more,
even if AIO_WAIT_WHILE() loops are still there (their condition is false
from the beginning). This is generally not a problem, but in
test-bdrv-drain, some additional explicit aio_poll() calls need to be
added because the test case wants to verify the final state after BHs
have executed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to change .bdrv_co_drained_begin/end() back to be non-coroutine
callbacks, so in preparation, avoid yielding in their implementation.
This does almost the same as the existing logic in bdrv_drain_invoke(),
by creating and entering coroutines internally. However, since the test
case is by far the heaviest user of coroutine code in drain callbacks,
it is preferable to have the complexity in the test case rather than the
drain core, which is already complicated enough without this.
The behaviour for bdrv_drain_begin() is unchanged because we increase
bs->in_flight and this is still polled. However, bdrv_drain_end()
doesn't wait for the spawned coroutine to complete any more. This is
fine, we don't rely on bdrv_drain_end() restarting all operations
immediately before the next aio_poll().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to change .bdrv_co_drained_begin() back to be a non-coroutine
callback, so in preparation, avoid yielding in its implementation.
Because we increase bs->in_flight and bdrv_drained_begin() polls, the
behaviour is unchanged.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221118174110.55183-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are going to increase usage of collecting nodes in a list to then
update, and calling bdrv_topological_dfs() each time is not convenient,
and not correct as we are going to interleave graph modifying with
filling the node list.
So, let's switch to a function that takes any list of nodes, adds all
their subtrees and do topological sort. And finally, refresh
permissions.
While being here, make the function public, as we'll want to use it
from blockdev.c in near future.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20221107163558.618889-5-vsementsov@yandex-team.ru>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Migration patches for 8.0
Hi
This are the patches that I had to drop form the last PULL request because they werent fixes:
- AVX2 is dropped, intel posted a fix, I have to redo it
- Fix for out of order channels is out
Daniel nacked it and I need to redo it
# gpg: Signature made Thu 15 Dec 2022 09:38:29 GMT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'next-8.0-pull-request' of https://gitlab.com/juan.quintela/qemu:
migration: Drop rs->f
migration: Remove old preempt code around state maintainance
migration: Send requested page directly in rp-return thread
migration: Move last_sent_block into PageSearchStatus
migration: Make PageSearchStatus part of RAMState
migration: Add pss_init()
migration: Introduce pss_channel
migration: Teach PSS about host page
migration: Use atomic ops properly for page accountings
migration: Yield bitmap_mutex properly when sending/sleeping
migration: Remove RAMState.f references in compression code
migration: Trivial cleanup save_page_header() on same block check
migration: Cleanup xbzrle zero page cache update logic
migration: Add postcopy_preempt_active()
migration: Take bitmap mutex when completing ram migration
migration: Export ram_release_page()
migration: Export ram_transferred_ram()
multifd: Create page_count fields into both MultiFD{Recv,Send}Params
multifd: Create page_size fields into both MultiFD{Recv,Send}Params
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This test requires environment variable QTEST_QEMU_STORAGE_DAEMON_BINARY
to be defined for running. If not, it would immediately abort all qtests
and prevent other, unrelated tests from running.
To fix that, just skip vhost-user-blk-test instead and log a message
about missing environment variable.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <E1oybRD-0005D5-5r@lizzy.crudebyte.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Many users forget to remove the suggestions from the bug template
when creating a new issue. So when searching for strings like "s390x"
or "Windows", you get a lot of unrelated issues in the results.
Thus let's move the suggestions into HTML comments - so they will
still show up in the markdown when editing the bug, while being
hidden/ignored in the final text or in the search queries.
Message-Id: <20221201133756.77216-1-thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Building QEMU for ppc64 hosts with --disable-tcg used to break a couple
of times in the past, see e.g. commit a01b64cee7 ("target/ppc: Put do_rfi
under a TCG-only block") or commit 049b4ad669 ("target/ppc: Fix build
warnings when building with 'disable-tcg'"), so we should test this in
our CI to avoid such regressions.
Message-Id: <20221208101527.36873-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
At present the build scripts of 32-bit and 64-bit are inconsistent.
Let's keep them consistent for easier maintenance.
While we are here, add some comments to explain that for the 64-bit
job, "--without-default-devices" is a must have, at least for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20221125114100.3184790-2-bmeng.cn@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It seems a little bit weird that the para-virtualized x86 VMWare
devices "vmware-svga" and "vmxnet3" also show up in non-x86 targets.
They are likely pretty useless there (since the guest OSes likely
do not have any drivers for those enabled), so let's change this and
only enable those devices by default for the classical x86 targets.
Message-Id: <20221213095144.42355-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A lot of files in the docs directory do not have a maintainer according to
our MAINTAINERS file, though they can be clearly associated with one of the
sections in there. Add the files now so that our scripts/get_maintainer.pl
script can output the right maintainer for them.
Message-Id: <20221212174841.201003-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The comment about g_poll is not required here anymore since
the corresponding code has been removed a while ago already.
Fixes: b4c6036faa ("configure: bump min required glib version to 2.56")
Message-Id: <20221208133257.95673-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "query-command-line-options" command uses a hand-crafted list
of options that should be returned for the "machine" parameter.
This is pretty much out of sync with reality, for example settings
like "kvm_shadow_mem" or "accel" are not parameters for the machine
anymore. Also, there is no distinction between the targets here, so
e.g. the s390x-specific values like "loadparm" in this list also
show up with the other targets like x86_64.
Let's fix this now by geting rid of the hand-crafted list and by
querying the properties of the machine classes instead to assemble
the list.
Fixes: 0a7cf217d8 ("fix regression of qmp_query_command_line_options")
Message-Id: <20221111141323.246267-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "MOVE TO PRIMARY/SECONDARY" instructions can also be called
from problem state. We just should properly check whether the
secondary-space access key is valid here, too, and inject a
privileged program exception if it is invalid.
Message-Id: <20221205125852.81848-1-thuth@redhat.com>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The PSW key mask is a 16 bit field, and the psw_key variable is
in the range from 0 to 15, so it does not make sense to use
"0x80 >> psw_key" for testing the bits here. We should use 0x8000
instead.
Message-Id: <20221205142043.95185-1-thuth@redhat.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ISM device firmware stores unique state information that can
can cause a wholesale unmap of the associated IOMMU (e.g. when
we get a termination signal for QEMU) to trigger firmware errors
because firmware believes we are attempting to invalidate entries
that are still in-use by the guest OS (when in fact that guest is
in the process of being terminated or rebooted).
To alleviate this, register both a shutdown notifier (for unexpected
termination cases e.g. virsh destroy) as well as a reset callback
(for cases like guest OS reboot). For each of these scenarios, trigger
PCI device reset; this is enough to indicate to firmware that the IOMMU
is no longer in-use by the guest OS, making it safe to invalidate any
associated IOMMU entries.
Fixes: 15d0e7942d ("s390x/pci: don't fence interpreted devices without MSI-X")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20221209195700.263824-1-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
[thuth: Adjusted the hunk in s390-pci-vfio.c due to different context]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently, s390x-pci performs accounting against the vfio DMA
limit and triggers the guest to clean up mappings when the limit
is reached. Let's go a step further and also limit the size of
the supported DMA aperture reported to the guest based upon the
initial vfio DMA limit reported for the container (if less than
than the size reported by the firmware/host zPCI layer). This
avoids processing sections of the guest DMA table during global
refresh that, for common use cases, will never be used anway, and
makes exhausting the vfio DMA limit due to mismatch between guest
aperture size and host limit far less likely and more indicitive
of an error.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20221028194758.204007-4-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We use 32bit value for linux,initrd-[start/end], when we have
loader_start > 4GB, there will be a wrong initrd_start passed
to the kernel, and the kernel will report the following warning.
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] initrd not fully accessible via the linear mapping -- please check your bootloader ...
[ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm64/mm/init.c:355 arm64_memblock_init+0x158/0x244
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G W 6.1.0-rc3-13250-g30a0b95b1335-dirty #28
[ 0.000000] Hardware name: Horizon Sigi Virtual development board (DT)
[ 0.000000] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.000000] pc : arm64_memblock_init+0x158/0x244
[ 0.000000] lr : arm64_memblock_init+0x158/0x244
[ 0.000000] sp : ffff800009273df0
[ 0.000000] x29: ffff800009273df0 x28: 0000001000cc0010 x27: 0000800000000000
[ 0.000000] x26: 000000000050a3e2 x25: ffff800008b46000 x24: ffff800008b46000
[ 0.000000] x23: ffff800008a53000 x22: ffff800009420000 x21: ffff800008a53000
[ 0.000000] x20: 0000000004000000 x19: 0000000004000000 x18: 00000000ffff1020
[ 0.000000] x17: 6568632065736165 x16: 6c70202d2d20676e x15: 697070616d207261
[ 0.000000] x14: 656e696c20656874 x13: 0a2e2e2e20726564 x12: 0000000000000000
[ 0.000000] x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
[ 0.000000] x8 : 0000000000000000 x7 : 796c6c756620746f x6 : 6e20647274696e69
[ 0.000000] x5 : ffff8000093c7c47 x4 : ffff800008a2102f x3 : ffff800009273a88
[ 0.000000] x2 : 80000000fffff038 x1 : 00000000000000c0 x0 : 0000000000000056
[ 0.000000] Call trace:
[ 0.000000] arm64_memblock_init+0x158/0x244
[ 0.000000] setup_arch+0x164/0x1cc
[ 0.000000] start_kernel+0x94/0x4ac
[ 0.000000] __primary_switched+0xb4/0xbc
[ 0.000000] ---[ end trace 0000000000000000 ]---
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000001000000000-0x0000001007ffffff]
This doesn't affect any machine types we currently support, because
for all of our machine types the RAM starts well below the 4GB
mark, but it does demonstrate that we're not currently writing
the device-tree properties quite as intended.
To fix it, we can change it to write these values to the dtb using a
type width matching #address-cells. This is the intended size for
these dtb properties, and is how u-boot, for instance, writes them,
although in practice the Linux kernel will cope with them being any
width as long as they're big enough to fit the value.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Message-id: 20221129160724.75667-1-schspa@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the TYPE_ARM_SMMUV3 device to 3-phase reset. The legacy
reset method doesn't do anything that's invalid in the hold phase, so
the conversion only requires changing it to a hold phase method, and
using the 3-phase versions of the "save the parent reset method and
chain to it" code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-3-peter.maydell@linaro.org
Convert the TYPE_ARM_SMMU device to 3-phase reset. The legacy method
doesn't do anything that's invalid in the hold phase, so the
conversion is simple and not a behaviour change.
Note that we must convert this base class before we can convert the
TYPE_ARM_SMMUV3 subclass -- transitional support in Resettable
handles "chain to parent class reset" when the base class is 3-phase
and the subclass is still using legacy reset, but not the other way
around.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221109161444.3397405-2-peter.maydell@linaro.org
Update the ID registers for TCG's '-cpu max' to report the
FEAT_EVT Enhanced Virtualization Traps support.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For FEAT_EVT, the HCR_EL2.TID4 trap allows trapping of the cache ID
registers CCSIDR_EL1, CCSIDR2_EL1, CLIDR_EL1 and CSSELR_EL1 (and
their AArch32 equivalents). This is a subset of the registers
trapped by HCR_EL2.TID2, which includes all of these and also the
CTR_EL0 register.
Our implementation already uses a separate access function for
CTR_EL0 (ctr_el0_access()), so all of the registers currently using
access_aa64_tid2() should also be checking TID4. Make that function
check both TID2 and TID4, and rename it appropriately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For FEAT_EVT, the HCR_EL2.TICAB bit allows trapping of the ICIALLUIS
and IC IALLUIS cache maintenance instructions.
The HCR_EL2.TOCU bit traps all the other cache maintenance
instructions that operate to the point of unification:
AArch64 IC IVAU, IC IALLU, DC CVAU
AArch32 ICIMVAU, ICIALLU, DCCMVAU
The two trap bits between them cover all of the cache maintenance
instructions which must also check the HCR_TPU flag. Turn the old
aa64_cacheop_pou_access() function into a helper function which takes
the set of HCR_EL2 flags to check as an argument, and call it from
new access_ticab() and access_tocu() functions as appropriate for
each cache op.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For FEAT_EVT, the HCR_EL2.TTLBOS bit allows trapping on EL1
use of TLB maintenance instructions that operate on the
outer shareable domain:
TLBI VMALLE1OS, TLBI VAE1OS, TLBI ASIDE1OS,TLBI VAAE1OS,
TLBI VALE1OS, TLBI VAALE1OS, TLBI RVAE1OS, TLBI RVAAE1OS,
TLBI RVALE1OS, and TLBI RVAALE1OS.
(There are no AArch32 outer-shareable TLB maintenance ops.)
Implement the trapping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For FEAT_EVT, the HCR_EL2.TTLBIS bit allows trapping on EL1 use of
TLB maintenance instructions that operate on the inner shareable
domain:
AArch64:
TLBI VMALLE1IS, TLBI VAE1IS, TLBI ASIDE1IS, TLBI VAAE1IS,
TLBI VALE1IS, TLBI VAALE1IS, TLBI RVAE1IS, TLBI RVAAE1IS,
TLBI RVALE1IS, and TLBI RVAALE1IS.
AArch32:
TLBIALLIS, TLBIMVAIS, TLBIASIDIS, TLBIMVAAIS, TLBIMVALIS,
and TLBIMVAALIS.
Add the trapping support.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
FEAT_EVT adds five new bits to the HCR_EL2 register: TTLBIS, TTLBOS,
TICAB, TOCU and TID4. These allow the guest to enable trapping of
various EL1 instructions to EL2. In this commit, add the necessary
code to allow the guest to set these bits if the feature is present;
because the bit is always zero when the feature isn't present we
won't need to use explicit feature checks in the "trap on condition"
tests in the following commits.
Note that although full implementation of the feature (mandatory from
Armv8.5 onward) requires all five trap bits, the ID registers permit
a value indicating that only TICAB, TOCU and TID4 are implemented,
which might be the case for CPUs between Armv8.2 and Armv8.5.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The ARM GICv3 TRM describes that the ITLinesNumber field of GICD_TYPER
register:
"indicates the maximum SPI INTID that the GIC implementation supports"
As SPI #0 is absolute IRQ #32, the max SPI INTID should have accounted
for the internal 16x SGI's and 16x PPI's. However, the original GICv3
model subtracted off the SGI/PPI. Cosmetically this can be seen at OS
boot (Linux) showing 32 shy of what should be there, i.e.:
[ 0.000000] GICv3: 224 SPIs implemented
Though in hw/arm/virt.c, the machine is configured for 256 SPI's. ARM
virt machine likely doesn't have a problem with this because the upper
32 IRQ's don't actually have anything meaningful wired. But, this does
become a functional issue on a custom use case which wants to make use
of these IRQ's. Additionally, boot code (i.e. TF-A) will only init up
to the number (blocks of 32) that it believes to actually be there.
Signed-off-by: Luke Starrett <lukes@xsightlabs.com>
Message-id: AM9P193MB168473D99B761E204E032095D40D9@AM9P193MB1684.EURP193.PROD.OUTLOOK.COM
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-A55 is one of the newer armv8.2+ CPUs; in particular
it supports the Privileged Access Never (PAN) feature. Add
a model of this CPU, so you can use a CPU type on the virt
board that models a specific real hardware CPU, rather than
having to use the QEMU-specific "max" CPU type.
Signed-off-by: Timofey Kutergin <tkutergin@gmail.com>
Message-id: 20221121150819.2782817-1-tkutergin@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 3 high memory regions are usually enabled by default, but they may
be not used. For example, VIRT_HIGH_GIC_REDIST2 isn't needed by GICv2.
This leads to waste in the PA space.
Add properties ("highmem-redists", "highmem-ecam", "highmem-mmio") to
allow users selectively disable them if needed. After that, the high
memory region for GICv3 or GICv4 redistributor can be disabled by user,
the number of maximal supported CPUs needs to be calculated based on
'vms->highmem_redists'. The follow-up error message is also improved
to indicate if the high memory region for GICv3 and GICv4 has been
enabled or not.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221029224307.138822-8-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the improvement to high memory region address assignment is
applied, the memory layout can be changed, introducing possible
migration breakage. For example, VIRT_HIGH_PCIE_MMIO memory region
is disabled or enabled when the optimization is applied or not, with
the following configuration. The configuration is only achievable by
modifying the source code until more properties are added to allow
users selectively disable those high memory regions.
pa_bits = 40;
vms->highmem_redists = false;
vms->highmem_ecam = false;
vms->highmem_mmio = true;
# qemu-system-aarch64 -accel kvm -cpu host \
-machine virt-7.2,compact-highmem={on, off} \
-m 4G,maxmem=511G -monitor stdio
Region compact-highmem=off compact-highmem=on
----------------------------------------------------------------
MEM [1GB 512GB] [1GB 512GB]
HIGH_GIC_REDISTS2 [512GB 512GB+64MB] [disabled]
HIGH_PCIE_ECAM [512GB+256MB 512GB+512MB] [disabled]
HIGH_PCIE_MMIO [disabled] [512GB 1TB]
In order to keep backwords compatibility, we need to disable the
optimization on machine, which is virt-7.1 or ealier than it. It
means the optimization is enabled by default from virt-7.2. Besides,
'compact-highmem' property is added so that the optimization can be
explicitly enabled or disabled on all machine types by users.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-7-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are three high memory regions, which are VIRT_HIGH_REDIST2,
VIRT_HIGH_PCIE_ECAM and VIRT_HIGH_PCIE_MMIO. Their base addresses
are floating on highest RAM address. However, they can be disabled
in several cases.
(1) One specific high memory region is likely to be disabled by
code by toggling vms->highmem_{redists, ecam, mmio}.
(2) VIRT_HIGH_PCIE_ECAM region is disabled on machine, which is
'virt-2.12' or ealier than it.
(3) VIRT_HIGH_PCIE_ECAM region is disabled when firmware is loaded
on 32-bits system.
(4) One specific high memory region is disabled when it breaks the
PA space limit.
The current implementation of virt_set_{memmap, high_memmap}() isn't
optimized because the high memory region's PA space is always reserved,
regardless of whatever the actual state in the corresponding
vms->highmem_{redists, ecam, mmio} flag. In the code, 'base' and
'vms->highest_gpa' are always increased for case (1), (2) and (3).
It's unnecessary since the assigned PA space for the disabled high
memory region won't be used afterwards.
Improve the address assignment for those three high memory region by
skipping the address assignment for one specific high memory region if
it has been disabled in case (1), (2) and (3). The memory layout may
be changed after the improvement is applied, which leads to potential
migration breakage. So 'vms->highmem_compact' is added to control if
the improvement should be applied. For now, 'vms->highmem_compact' is
set to false, meaning that we don't have memory layout change until it
becomes configurable through property 'compact-highmem' in next patch.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Miscellaneous patches for 2022-12-14
# gpg: Signature made Wed 14 Dec 2022 15:23:02 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-misc-2022-12-14' of https://repo.or.cz/qemu/armbru:
ppc4xx_sdram: Simplify sdram_ddr_size() to return
block/vmdk: Simplify vmdk_co_create() to return directly
cleanup: Tweak and re-run return_directly.cocci
io: Tidy up fat-fingered parameter name
qapi: Use returned bool to check for failure (again)
sockets: Use ERRP_GUARD() where obviously appropriate
qemu-config: Use ERRP_GUARD() where obviously appropriate
qemu-config: Make config_parse_qdict() return bool
monitor: Use ERRP_GUARD() in monitor_init()
monitor: Simplify monitor_fd_param()'s error handling
error: Move ERRP_GUARD() to the beginning of the function
error: Drop a few superfluous ERRP_GUARD()
error: Drop some obviously superfluous error_propagate()
Drop more useless casts from void * to pointer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now with rs->pss we can already cache channels in pss->pss_channels. That
pss_channel contains more infromation than rs->f because it's per-channel.
So rs->f could be replaced by rss->pss[RAM_CHANNEL_PRECOPY].pss_channel,
while rs->f itself is a bit vague now.
Note that vanilla postcopy still send pages via pss[RAM_CHANNEL_PRECOPY],
that's slightly confusing but it reflects the reality.
Then, after the replacement we can safely drop rs->f.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
With the new code to send pages in rp-return thread, there's little help to
keep lots of the old code on maintaining the preempt state in migration
thread, because the new way should always be faster..
Then if we'll always send pages in the rp-return thread anyway, we don't
need those logic to maintain preempt state anymore because now we serialize
things using the mutex directly instead of using those fields.
It's very unfortunate to have those code for a short period, but that's
still one intermediate step that we noticed the next bottleneck on the
migration thread. Now what we can do best is to drop unnecessary code as
long as the new code is stable to reduce the burden. It's actually a good
thing because the new "sending page in rp-return thread" model is (IMHO)
even cleaner and with better performance.
Remove the old code that was responsible for maintaining preempt states, at
the meantime also remove x-postcopy-preempt-break-huge parameter because
with concurrent sender threads we don't really need to break-huge anymore.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
With all the facilities ready, send the requested page directly in the
rp-return thread rather than queuing it in the request queue, if and only
if postcopy preempt is enabled. It can achieve so because it uses separate
channel for sending urgent pages. The only shared data is bitmap and it's
protected by the bitmap_mutex.
Note that since we're moving the ownership of the urgent channel from the
migration thread to rp thread it also means the rp thread is responsible
for managing the qemufile, e.g. properly close it when pausing migration
happens. For this, let migration_release_from_dst_file to cover shutdown
of the urgent channel too, renaming it as migration_release_dst_files() to
better show what it does.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since we use PageSearchStatus to represent a channel, it makes perfect
sense to keep last_sent_block (aka, leverage RAM_SAVE_FLAG_CONTINUE) to be
per-channel rather than global because each channel can be sending
different pages on ramblocks.
Hence move it from RAMState into PageSearchStatus.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We used to allocate PSS structure on the stack for precopy when sending
pages. Make it static, so as to describe per-channel ram migration status.
Here we declared RAM_CHANNEL_MAX instances, preparing for postcopy to use
it, even though this patch has not yet to start using the 2nd instance.
This should not have any functional change per se, but it already starts to
export PSS information via the RAMState, so that e.g. one PSS channel can
start to reference the other PSS channel.
Always protect PSS access using the same RAMState.bitmap_mutex. We already
do so, so no code change needed, just some comment update. Maybe we should
consider renaming bitmap_mutex some day as it's going to be a more commonly
and big mutex we use for ram states, but just leave it for later.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce pss_channel for PageSearchStatus, define it as "the migration
channel to be used to transfer this host page".
We used to have rs->f, which is a mirror to MigrationState.to_dst_file.
After postcopy preempt initial version, rs->f can be dynamically changed
depending on which channel we want to use.
But that later work still doesn't grant full concurrency of sending pages
in e.g. different threads, because rs->f can either be the PRECOPY channel
or POSTCOPY channel. This needs to be per-thread too.
PageSearchStatus is actually a good piece of struct which we can leverage
if we want to have multiple threads sending pages. Sending a single guest
page may not make sense, so we make the granule to be "host page", and in
the PSS structure we allow specify a QEMUFile* to migrate a specific host
page. Then we open the possibility to specify different channels in
different threads with different PSS structures.
The PSS prefix can be slightly misleading here because e.g. for the
upcoming usage of postcopy channel/thread it's not "searching" (or,
scanning) at all but sending the explicit page that was requested. However
since PSS existed for some years keep it as-is until someone complains.
This patch mostly (simply) replace rs->f with pss->pss_channel only. No
functional change intended for this patch yet. But it does prepare to
finally drop rs->f, and make ram_save_guest_page() thread safe.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Migration code has a lot to do with host pages. Teaching PSS core about
the idea of host page helps a lot and makes the code clean. Meanwhile,
this prepares for the future changes that can leverage the new PSS helpers
that this patch introduces to send host page in another thread.
Three more fields are introduced for this:
(1) host_page_sending: this is set to true when QEMU is sending a host
page, false otherwise.
(2) host_page_{start|end}: these point to the start/end of host page
we're sending, and it's only valid when host_page_sending==true.
For example, when we look up the next dirty page on the ramblock, with
host_page_sending==true, we'll not try to look for anything beyond the
current host page boundary. This can be slightly efficient than current
code because currently we'll set pss->page to next dirty bit (which can be
over current host page boundary) and reset it to host page boundary if we
found it goes beyond that.
With above, we can easily make migration_bitmap_find_dirty() self contained
by updating pss->page properly. rs* parameter is removed because it's not
even used in old code.
When sending a host page, we should use the pss helpers like this:
- pss_host_page_prepare(pss): called before sending host page
- pss_within_range(pss): whether we're still working on the cur host page?
- pss_host_page_finish(pss): called after sending a host page
Then we can use ram_save_target_page() to save one small page.
Currently ram_save_host_page() is still the only user. If there'll be
another function to send host page (e.g. in return path thread) in the
future, it should follow the same style.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To prepare for thread-safety on page accountings, at least below counters
need to be accessed only atomically, they are:
ram_counters.transferred
ram_counters.duplicate
ram_counters.normal
ram_counters.postcopy_bytes
There are a lot of other counters but they won't be accessed outside
migration thread, then they're still safe to be accessed without atomic
ops.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Don't take the bitmap mutex when sending pages, or when being throttled by
migration_rate_limit() (which is a bit tricky to call it here in ram code,
but seems still helpful).
It prepares for the possibility of concurrently sending pages in >1 threads
using the function ram_save_host_page() because all threads may need the
bitmap_mutex to operate on bitmaps, so that either sendmsg() or any kind of
qemu_sem_wait() blocking for one thread will not block the other from
progressing.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Removing referencing to RAMState.f in compress_page_with_multi_thread() and
flush_compressed_data().
Compression code by default isn't compatible with having >1 channels (or it
won't currently know which channel to flush the compressed data), so to
make it simple we always flush on the default to_dst_file port until
someone wants to add >1 ports support, as rs->f right now can really
change (after postcopy preempt is introduced).
There should be no functional change at all after patch applied, since as
long as rs->f referenced in compression code, it must be to_dst_file.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The major change is to replace "!save_page_use_compression()" with
"xbzrle_enabled" to make it clear.
Reasonings:
(1) When compression enabled, "!save_page_use_compression()" is exactly the
same as checking "xbzrle_enabled".
(2) When compression disabled, "!save_page_use_compression()" always return
true. We used to try calling the xbzrle code, but after this change we
won't, and we shouldn't need to.
Since at it, drop the xbzrle_enabled check in xbzrle_cache_zero_page()
because with this change it's not needed anymore.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Any call to ram_find_and_save_block() needs to take the bitmap mutex. We
used to not take it for most of ram_save_complete() because we thought
we're the only one left using the bitmap, but it's not true after the
preempt full patchset applied, since the return path can be taking it too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We were recalculating it left and right. We plan to change that
values on next patches.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Leonardo Bras <leobras@redhat.com>
We were calling qemu_target_page_size() left and right.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Leonardo Bras <leobras@redhat.com>
QAPI patches patches for 2022-12-14
# gpg: Signature made Wed 14 Dec 2022 19:14:34 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-qapi-2022-12-14-v2' of https://repo.or.cz/qemu/armbru: (30 commits)
qapi: Drop temporary logic to support conversion step by step
qapi qga: Elide redundant has_FOO in generated C
qapi virtio: Elide redundant has_FOO in generated C
qapi ui: Elide redundant has_FOO in generated C
qapi transaction: Elide redundant has_FOO in generated C
qapi tpm: Elide redundant has_FOO in generated C
qapi stats: Elide redundant has_FOO in generated C
qapi run-state: Elide redundant has_FOO in generated C
qapi rocker: Elide redundant has_FOO in generated C
qapi replay: Elide redundant has_FOO in generated C
qapi qdev qom: Elide redundant has_FOO in generated C
qapi pci: Elide redundant has_FOO in generated C
qapi net: Elide redundant has_FOO in generated C
qapi misc: Elide redundant has_FOO in generated C
qapi migration: Elide redundant has_FOO in generated C
qapi machine: Elide redundant has_FOO in generated C
qapi job: Elide redundant has_FOO in generated C
qapi dump: Elide redundant has_FOO in generated C
qapi crypto: Elide redundant has_FOO in generated C
qapi chardev: Elide redundant has_FOO in generated C
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qga/qapi-schema.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Michael Roth <michael.roth@amd.com>
Cc: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-30-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/virtio.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-29-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/ui.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-28-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/transaction.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
In qmp_transaction(), we can't just drop parameter @has_props, since
it's used to track whether @props needs to be freed. Replace it by a
local variable.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Hanna Reitz <hreitz@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-27-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/tpm.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20221104160712.3005652-26-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/stats.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Mark Kanda <mark.kanda@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-25-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/run-state.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Drop a superfluous conditional around
qapi_free_GuestPanicInformation() while there.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-24-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/rocker.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/replay.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-22-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/qdev.json and
qapi/qom.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Cc: Eduardo Habkost <eduardo@habkost.net>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-21-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/pci.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-20-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/net.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[Fixes for MacOS squashed in]
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/misc.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221104160712.3005652-18-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/migration.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-17-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/machine*.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-16-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/job.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: John Snow <jsnow@redhat.com>
Cc: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20221104160712.3005652-15-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/dump.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-14-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/crypto.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Daniel P. Berrangé" <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-13-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/char.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-12-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/block*.json.
Said commit explains the transformation in more detail.
There is one instance of the invariant violation mentioned there:
qcow2_signal_corruption() passes false, "" when node_name is an empty
string. Take care to pass NULL then.
The previous two commits cleaned up two more.
Additionally, helper bdrv_latency_histogram_stats() loses its output
parameters and returns a value instead.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Hanna Reitz <hreitz@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-11-armbru@redhat.com>
[Fixes for #ifndef LIBRBD_SUPPORTS_ENCRYPTION and MacOS squashed in]
Tweak the semantic patch to drop redundant parenthesis around the
return expression.
Coccinelle drops a comment in hw/rdma/vmw/pvrdma_cmd.c; restored
manually.
Coccinelle messes up vmdk_co_create(), not sure why. Change dropped,
will be done manually in the next commit.
Line breaks in target/avr/cpu.h and hw/rdma/vmw/pvrdma_cmd.c tidied up
manually.
Whitespace in tools/virtiofsd/fuse_lowlevel.c tidied up manually.
checkpatch.pl complains "return of an errno should typically be -ve"
two times for hw/9pfs/9p-synth.c. Preexisting, the patch merely makes
it visible to checkpatch.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221122134917.1217307-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 012d4c96e2 changed the visitor functions taking Error ** to
return bool instead of void, and the commits following it used the new
return value to simplify error checking. Since then a few more uses
in need of the same treatment crept in. Do that. All pretty
mechanical except for
* balloon_stats_get_all()
This is basically the same transformation commit 012d4c96e2 applied
to the virtual walk example in include/qapi/visitor.h.
* set_max_queue_size()
Additionally replace "goto end of function" by return.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
include/qapi/error.h advises to put ERRP_GUARD() right at the
beginning of the function, because only then can it guard the whole
function. Clean up the few spots disregarding the advice.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
include/qapi/error.h on ERRP_GUARD():
* It must be used when the function dereferences @errp or passes
* @errp to error_prepend(), error_vprepend(), or error_append_hint().
* It is safe to use even when it's not needed, but please avoid
* cluttering the source with useless code.
Clean up some of this clutter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-3-armbru@redhat.com>
When error_propagate(errp, local_err) is the only reader of
@local_err, we can just as well change its writers to write @errp
directly, and drop the error_propagate() along with @local_err.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
block-export-add argument @name defaults to the value of argument
@node-name.
nbd_export_create() implements this by copying @node_name to @name.
It leaves @has_node_name false, violating the "has_node_name ==
!!node_name" invariant. Unclean. Falls apart when we elide
@has_node_name (next commit): then QAPI frees the same value twice,
once for @node_name and once @name. iotest 307 duly explodes.
Goes back to commit c62d24e906 "blockdev-nbd: Boxed argument type for
nbd-server-add" (v5.0.0). Got moved from qmp_nbd_server_add() to
nbd_export_create() (commit 56ee86261e), then copied back (commit
b6076afcab). Commit 8675cbd68b "nbd: Utilize QAPI_CLONE for type
conversion" (v5.2.0) cleaned up the copy in qmp_nbd_server_add()
noting
Second, our assignment to arg->name is fishy: the generated QAPI code
for qapi_free_NbdServerAddOptions does not visit arg->name if
arg->has_name is false, but if it DID visit it, we would have
introduced a double-free situation when arg is finally freed.
Exactly. However, the copy in nbd_export_create() remained dirty.
Clean it up. Since the value stored in member @name is not actually
used outside this function, use a local variable instead of modifying
the QAPI object.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Cc: qemu-block@nongnu.org
Message-Id: <20221104160712.3005652-10-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
drive-backup argument @format defaults to the format of the source
unless @mode is "existing".
drive_backup_prepare() implements this by copying the source's
@format_name to DriveBackup member @format. It leaves @has_format
false, violating the "has_format == !!format" invariant. Unclean.
Falls apart when we elide @has_format (commit after next): then QAPI
passes @format, which is a string constant, to g_free(). iotest 056
duly explodes.
Clean it up. Since the value stored in member @format is not actually
used outside this function, use a local variable instead of modifying
the QAPI object.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Hanna Reitz <hreitz@redhat.com>
Cc: qemu-block@nongnu.org
Message-Id: <20221104160712.3005652-9-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/audio.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Additionally, helper get_str() loses its @has_dst parameter.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-8-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/acpi.py.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-7-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for
tests/qapi-schema/qapi-schema-test.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-6-armbru@redhat.com>
In QAPI, absent optional members are distinct from any present value.
We thus represent an optional schema member FOO as two C members: a
FOO with the member's type, and a bool has_FOO. Likewise for function
arguments.
However, has_FOO is actually redundant for a pointer-valued FOO, which
can be null only when has_FOO is false, i.e. has_FOO == !!FOO. Except
for arrays, where we a null FOO can also be a present empty array.
The redundant has_FOO are a nuisance to work with. Improve the
generator to elide them. Uses of has_FOO need to be replaced as
follows.
Tests of has_FOO become the equivalent comparison of FOO with null.
For brevity, this is commonly done by implicit conversion to bool.
Assignments to has_FOO get dropped.
Likewise for arguments to has_FOO parameters.
Beware: code may violate the invariant has_FOO == !!FOO before the
transformation, and get away with it. The above transformation can
then break things. Two cases:
* Absent: if code ignores FOO entirely when !has_FOO (except for
freeing it if necessary), even non-null / uninitialized FOO works.
Such code is known to exist.
* Present: if code ignores FOO entirely when has_FOO, even null FOO
works. Such code should not exist.
In both cases, replacing tests of has_FOO by FOO reverts their sense.
We have to fix the value of FOO then.
To facilitate review of the necessary updates to handwritten code, add
means to opt out of this change, and opt out for all QAPI schema
modules where the change requires updates to handwritten code. The
next few commits will remove these opt-outs in reviewable chunks, then
drop the means to opt out.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-5-armbru@redhat.com>
The next commit will change the code generated for some optional
members. The example schema contains an optional member affected by
the change. Add one that is not affected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-4-armbru@redhat.com>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
