WORKING WITH THE SUSE 2.6.x and 3.x KERNEL SOURCES
Andreas Gruenbacher <agruen@suse.de>, SUSE Labs, 2003, 2004, 2005, 2006
Michal Marek <mmarek@suse.de>, SUSE Labs, 2010
This document gives an overview of how SUSE Linux kernels are
created, and describes tasks like building individual kernels
and creating external kernel modules.
A companion HOWTO that describes how to build driver update disks (among
other things) is available at:
http://developer.novell.com/wiki/index.php/Creating_a_Driver_Update_Disk_%28DUD%29
TABLE OF CONTENTS
Overview
Compiling your own kernel
Building additional (external) modules
Supported vs. unsupported modules
Patch selection mechanism
Where to find configuration files
How to configure the kernel sources
Module load paths
OVERVIEW
The kernels for SUSE are generated from the vanilla Linux kernel sources
found at http://ftp.kernel.org, on top of which a number of patches are
applied. The resulting kernel source tree is configured and built,
resulting in a binary kernel.
The add-on patches and configuration files are maintained in
a GIT repository at
http://gitorious.org/opensuse/kernel-source
A script (scripts/tar-up.sh) packs up the files in the repository in a
form suitable for rpmbuild. When building the RPM packages, the
following binary packages get created:
* kernel-source
The kernel source tree, generated by unpacking the vanilla kernel
sources and applying the patches. The kernel sources are used by
a number of other packages. They can also be used for compiling
additional kernel modules.
* kernel-devel
A subset of the kernel-source package that is needed to build
external modules.
* kernel-$FLAVOR
A number of binary kernels (for example, kernel-default for
uniprocessor machines, kernel-smp for smp machines, etc.). These
packages are all generated from the same kernel sources, and
differ in the kernel configurations used.
* kernel-$FLAVOR-base
A subset of kernel-$FLAVOR, for use in paravirtualized quests that
only require a few device and filesystem drivers.
* kernel-$FLAVOR-devel
The files used for generating kernel module packages for use with
kernel-$FLAVOR.
* kernel-syms
A meta package that pulls in the relevant kernel-$FLAVOR-devel
packages for a given architecture.
The repository contains the configuration files (.config) for all SUSE
kernel flavors. All configuration files are included in the dependencies
of the kernel-syms package (see WHERE TO FIND CONFIGURATION FILES below).
In the installed system, the kernel-source package installs files in the
following directories:
* /usr/src/linux-$VERSION-$RELEASE/
The kernel sources.
* /usr/src/linux
A symbolic link to /usr/src/linux-$VERSION-$RELEASE.
* /usr/share/doc/packages/kernel-source/
This document.
The kernel-$FLAVOR-devel packages install the following files:
* /usr/src/linux-$VERSION-$RELEASE-obj/$ARCH/$FLAVOR/
Kernel build object files for one kernel flavor. These
files are used for compiling additional kernel modules.
* /usr/src/linux-obj/$ARCH/$FLAVOR
A symbolic link to /usr/src/linux-$VERSION-$RELEASE-obj/$ARCH/$FLAVOR.
COMPILING YOUR OWN KERNEL
The kernel sources are found in the kernel-source package. The
recommended way to produce a binary kernel is:
(1) Install kernel-source. Change to the /usr/src/linux directory.
(2) Create a build directory for use in configuring and building
the kernel. Using /usr/src/linux directly requires root priviledges
and will cause problems if you need to build kernel modules for
other installed kernels.
(3) Configure the kernel (for example, ``make -C /usr/src/linux
O=$(pwd) oldconfig'' or ``make -C /usr/src/linux O=$(pwd) cloneconfig'',
see HOW TO CONFIGURE THE KERNEL SOURCES).
(4) Build the kernel and all its modules (``make'').
(5) Make sure that /etc/modprobe.d/unsupported-modules contains
allow_unsupported_modules 1
otherwise modprobe will refuse to load any modules.
(6) Install the kernel and the modules (``make modules_install'',
followed by ``make install''). This will automatically create
an initrd for the new kernel as well (see ``mkinitrd -h'').
(7) Add the kernel to the boot manager. When using lilo, run ``lilo''
to update the boot map.
Instead of building binary kernels by hand, you can also build
one of the kernel-$FLAVOR packages using RPM.
BUILDING ADDITIONAL (EXTERNAL) MODULES
A single binary kernel module generally only works for a specific
version of the kernel source tree, for a specific architecture and
configuration. This means that for each binary kernel that SUSE ships, a
custom module must be built. This requirement is to some extent relaxed
by the modversion mechanism: modversions attach a checksum to each
symbol (function or variable) exported to modules by the kernel. This
allows to use kernel modules that have been built for a kernel with a
different version or release number in many cases, as long as none of
the symbols the module uses have changed between the two kernel
versions.
When releasing maintenance or security update kernels for a specific
product, we carefully try to keep the kernel ABI stable. Despite this,
we sometimes have no choice but to break binary compatibility. In this
case, those kernel modules must be rebuilt.
Additional kernel modules for one of the SUSE kernel flavors can be
built in three different ways:
(1) by configuring the kernel sources in a separate build directory
(see HOW TO CONFIGURE THE KERNEL SOURCES), or
(2) by using one of the standard configurations in
/usr/src/linux-obj/$ARCH/$FLAVOR, or
(3) by creating a Kernel Module Package (KMP) as described in the
Kernel Module Packages Manual, http://www.suse.de/~agruen/KMPM/.
The first method involves the following steps:
(1) Install the kernel-source package.
(2) Configure the kernel, see HOW TO CONFIGURE THE KERNEL SOURCES.
(3) Create files required for compiling external modules:
``make scripts'' and ``make prepare''.
(4) Compile the module(s) by changing into the module source directory
and typing ``make -C $(your_build_dir) M=$(pwd)''.
(5) Install the module(s) by typing
``make -C $(your_build_dir) M=$(pwd) modules_install''.
The second method involves the following steps:
(1) Install the kernel-devel package.
(2) Install the kernel-$FLAVOR-devel package. This is necessary for
symbol version information (CONFIG_MODVERSIONS).
(3) Compile the module(s) by changing into the module source directory
and typing ``make -C /usr/src/linux-obj/$ARCH/$FLAVOR M=$(pwd)''.
Substitute $ARCH and $FLAVOR with the architecture and flavor
for which to build the module(s).
If the installed kernel sources match the running kernel, you
can build modules for the running kernel by using the path
/lib/modules/$(uname -r)/build as the -C option in the above
command. (build is a symlink to /usr/src/linux-obj/$ARCH/$FLAVOR).
(4) Install the module(s) with
``make -C /usr/src/linux-obj/$ARCH/$FLAVOR M=$(pwd) modules_install''.
Whenever building modules, please use the kernel build infrastructure as
much as possible, and do not try to circumvent it. The
Documentation/kbuild directory in the kernel sources documents kbuild
makefiles.
SUPPORTED VS. UNSUPPORTED MODULES
As an extension to the mainline kernel, modules can be tagged as
supported (directly by SUSE, or indirectly by a third party) or
unsupported. Modules which are known to be flakey or for which SUSE does
not have the necessary expertise are marked as unsupported. Modules for
which SUSE has third-party support agreements are marked as externally
supported. Modules for which SUSE provides direct support are marked as
supported.
The support status of a module can be queried with the modinfo tool.
Modinfo will report one of the following:
- direct support by SUSE: "supported: yes"
- third-party support: "supported: external"
- unsupported modules: no supported tag.
At runtime, the setting of the" unsupported" kernel command line
parameter and /proc/sys/kernel/unsupported determines whether
unsupported modules can be loaded or not, and whether or not loading an
unsupported module causes a warning in the system log:
0 = only allow supported modules,
1 = warn when loading unsupported modules,
2 = don't warn.
Irrespective of this setting, loading an externally supported or unsupported
module both set a kernel taint flag. The taint flags are included in
Oopses. The taint status of the kernel can be inspected in
/proc/sys/kernel/tainted: Bits 0 to 4 have the following meanings:
bit 0 = a module with a GPL-incompatible license was loaded (tainted & 1),
bit 1 = module load was enforced (tainted & 2),
bit 2 = an SMP-unsafe module was loaded (tainted & 4),
bit 3 = (reserved),
bit 4 = an unsupported module was loaded (tainted & 16),
bit 5 = a module with third-party support was loaded (tainted & 32).
bit 10 = a machine check exception has occurred (taint & 1024; x86_64 only
so far).
The corresponding codes for the taint flags in Oopses are (x = unknown):
- "Pxxx" if bit 0 set or else
"Gxxx" if bit 0 unset,
- "xFxx" if bit 1 set or else
"x xx" if bit 1 unset,
- "xxSx" if set or else
"xx x" if bit 2 unset,
- "xxxU" if bit 4 set or else
"xxxX" if bit 5 set or else
"xxx ".
By default, external modules will not have the supported flag (that is,
they wil be marked as unsupported). For building externally supported
modules, please get in touch with Kurt Garloff <garloff@suse.de>.
PATCH SELECTION MECHANISM
The SUSE kernels consist of the vanilla kernel sources on top of which a
number of patches is applied. The file series.conf determines which
patches are applied and which are excluded. A script named "guards"
converts series.conf into a plain list of patch files to be applied.
Guards decides which patches to include and exclude based on a list of
symbols. From the kernel-source.src.rpm package, a fully patched
kernel source tree can be generated from vanilla sources + patches like
this:
# Install the package:
$ rpm -i kernel-source.src.rpm
# Unpack the patches and the kernel sources:
$ cd /usr/src/packages/SOURCES
$ for f in patches.*.tar.bz2; do \
tar -xjf "$f" || break; \
done
$ tar -xjf linux-2.6.5.tar.bz2
# Apply the patches
$ for p in $(./guards < series.conf); do
patch -d linux-2.6.5 -p1 < $p || break
done
The configuration script config.conf which is similar to series.conf is
used for configuration file selection. See the section WHERE TO FIND
CONFIGURATION FILES.
The file format of series.conf and config.conf should be obvious from
the comments in series.conf, and from the guards(1) manual page. (The
guards(1) manual page can be generated by running pod2man on the guards
script.)
WHERE TO FIND CONFIGURATION FILES
Kernel configuration files are stored in the kernel GIT repository. When
packing up the repository, they end up in config.tar.bz2.
The kernel-$FLAVOR packages are based on config/$ARCH/$FLAVOR.
(kernel-default is based on config/$ARCH/default, for example). The
kernel-$FLAVOR packages install their configuration files as
/boot/config-$VER_STR (for example, /boot/config-2.6.5-99-default). The
config is also packaged in the kernel-$FLAVOR-devel package as
/usr/src/linux-obj/$ARCH/$FLAVOR/.config.
In addition, the running kernel exposes a gzip compressed version of its
configuration file as /proc/config.gz. The kernel sources can be
configured based on /proc/config.gz with ``make cloneconfig''.
HOW TO CONFIGURE THE KERNEL SOURCES
Before a binary kernel is built or an additional loadable module
for an existing kernel is created, the kernel must be configured.
In order for a loadable module to work with an existing kernel, it must
be created with a configuration that is identical to the kernel's
configuration, or at least very close to that. Each configuration is
contained in a single file. The kernel-syms package installs
configurations for all standard SUSE kernel variants, so for building
only external kernel modules it is not necessary to configure the kernel
sources.
Configuring the kernel sources for a specific configuration is
straightfoward:
- Locate the configuration file you want to use. (See WHERE TO FIND
CONFIGURATION FILES above).
- Copy the configuration to the file .config in your build directory.
- Run the following commands in sequence to apply the configuration,
generate version information files, etc.:
make -C /usr/src/linux O=$PWD clean
make -C /usr/src/linux O=$PWD oldconfig
Alternatively to ``make oldconfig'', you can also use ``make
menuconfig'' for a text menu oriented user interface. If the kernel
sources do not match the configuration file exactly, ``make
oldconfig'' will prompt for settings that are undefined. Once this
step is completed, a Makefile will have been created that eliminates
the need to specify the locations of the kernel source and the build
directory.
For configuring the kernel to match the running kernel, there is a
shortcut ``make cloneconfig'' that expands the file /proc/config.gz
into .config, and then runs ``make oldconfig''.
HOW TO ADD CUSTOM PATCHES
Typically patches are added to the appropriate patches.* directory (e.g.
patches.fixes) and to series.conf. When the kernel-source package is
exported from the git repository, the patch will be automatically added
to the appropriate patch tarball.
If your goal is to create a kernel with only a few additional patches
and you don't want to be bothered with using the git repository, there
is an easier way.
The kernel-source SRPM ships with two empty archives that can be be
filled and automatically expanded when building the kernel. You can use
these to add your own patches and config options without disturbing the
rest of the kernel package. This is useful if you are using the openSUSE
Build Service and link to the main kernel-source project instead of
creating your own branch. The advantage to this is that your project
will automatically receive all the changes that go into the main project
without any further effort.
To add a patch using this mechanism, just add it to the
patches.addon.tar.bz2 archive and add an entry to the series.conf file.
The archive will be expanded automatically with the other kernel patches
when the source tree is constructed.
Some patches may add new Kconfig options. The config.addon.tar.bz2
archive contains the same hierarchy as config.tar.bz2, but is under
config.addon. You can add your new config options to files named after
their config/ counterparts.
For example, the file used to configure the i386 default kernel is named
config/i386/default. To add config options to that kernel, you would
create a new file called config.addon/i386/default with the options as
formatted in a normal Linux kernel .config file. This is important
because the kernel build is non-interactive and will fail if it
encounters new config options without entries in the config file.
MODULE LOAD PATHS
Modules that belong to a specific kernel release are installed in
/lib/modules/2.6.5-99-smp and similar. Note that this path contains the
kernel package release number. Modules from KMPs must be installed
below /lib/modules/2.6.5-99-smp/updates/ and similar: modules below
updates/ have priority over other modules.
When KMPs contain modules that are compatible between multiple installed
kernels, symlinks are used to make those modules available to those
compatible kernels like this:
/lib/modules/2.6.16-100-smp/weak-updates/foo.ko ->
/lib/modules/2.6.16-99-smp/updates/foo.ko
Modules in the weak-updates directory have lower priority than modules
in /lib/modules/2.6.16-100-smp/updates/, and higher priority than other
modules in /lib/modules/2.6.16-100-smp.
REFERENCES
General
Documentation in the kernel source tree.
Linux Documentation Project, http://www.tldp.org/
Linux Weekly News, http://lwn.net
Rusty's Remarkably Unreliable Guides (Kernel Hacking
and Kernel Locking guides),
http://www.netfilter.org/unreliable-guides/
Kernel newbies, http://www.kernelnewbies.org/
Loadable Kernel Modules
Peter Jay Salzman and Ori Pomerantz: Linux Kernel Module
Programming Guide, Version 2.4, April 2003,
http://www.tldp.org/guides.html
Kernel Module Packages
Andreas Gruenbacher: Kernel Module Packages Manual.
Versions for CODE9 (SLES9, SUSE LINUX 10.0) and CODE10
(SUSE Linux 10.1, SLES10),
http://www.suse.de/~agruen/KMPM/
337bf7fad4