This enforces proper alignment and makes the register update
more natural. Note that there is a more serious bug fix for
fmov {DX}Rn,@(R0,Rn) to use a store instead of a load.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170718200255.31647-17-rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We were treating FREG as an index and REG as a TCGv.
Making FREG return a TCGv is both less confusing and
a step toward cleaner banking of cpu_fregs.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170718200255.31647-12-rth@twiddle.net>
[aurel32: fix whitespace issues]
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For many of the sequences produced by gcc or glibc,
we can translate these as host atomic operations.
Which saves the need to acquire the exclusive lock.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170718200255.31647-8-rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For uniprocessors, SH4 uses optimistic restartable atomic sequences.
Upon an interrupt, a real kernel would simply notice magic values in
the registers and reset the PC to the start of the sequence.
For QEMU, we cannot do this in quite the same way. Instead, we notice
the normal start of such a sequence (mov #-x,r15), and start a new TB
that can be executed under cpu_exec_step_atomic.
Reported-by: Bruno Haible <bruno@clisp.org>
LP: https://bugs.launchpad.net/bugs/1701971
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170718200255.31647-7-rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since that the T bit of the SR register is mapped using a TGC global,
it's better to return the value through TCG than writing it directly. It
allows to declare the helpers with the flag TCG_CALL_NO_WG.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170702202814.27793-5-aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The floating-point status/control register contains cause and flag
bits. The cause bits are set to 0 before executing the instruction,
while the flag bits hold the status of the exception generated after
the field was last cleared.
Message-Id: <20170702202814.27793-4-aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SH4 manual is not fully clear about that, but real hardware do not
check for the PR bit, which allows to select between single or double
precision, for the fabs instruction. This is probably what is meant by
"Same operation is performed regardless of precision."
Remove the check, and at the same time use a TCG instruction instead of
a helper to clear one bit.
LP: https://bugs.launchpad.net/qemu/+bug/1701821
Reported-by: Bruno Haible <bruno@clisp.org>
Message-Id: <20170702202814.27793-2-aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
s390: add z14 cpu model
- add a CPU model for the IBM z14 which was announced on July 17th 2017
- update linux headers to 4.13-rc0 to get a fix for an ioctl definition
# gpg: Signature made Tue 18 Jul 2017 09:56:24 BST
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170718:
s390x/cpumodel: z14 cpu models
linux header sync against v4.13-rc1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x86 and machine queue, 2017-07-17
# gpg: Signature made Mon 17 Jul 2017 19:46:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-and-machine-pull-request:
qmp: Include parent type on 'qom-list-types' output
qmp: Include 'abstract' field on 'qom-list-types' output
tests: Simplify abstract-interfaces check with a helper
i386: add Skylake-Server cpu model
i386: Update comment about XSAVES on Skylake-Client
i386: expose "TCGTCGTCGTCG" in the 0x40000000 CPUID leaf
fw_cfg: move QOM type defines and fw_cfg types into fw_cfg.h
fw_cfg: move qdev_init_nofail() from fw_cfg_init1() to callers
fw_cfg: switch fw_cfg_find() to locate the fw_cfg device by type rather than path
qom: Fix ambiguous path detection when ambiguous=NULL
Revert "machine: Convert abstract typename on compat_props to subclass names"
test-qdev-global-props: Test global property ordering
qdev: fix the order compat and global properties are applied
tests: Test case for object_resolve_path*()
device-crash-test: Fix regexp on whitelist
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Queued target/mips patches
# gpg: Signature made Mon 17 Jul 2017 15:50:27 BST
# gpg: using RSA key 0xBA9C78061DDD8C9B
# gpg: Good signature from "Aurelien Jarno <aurelien@aurel32.net>"
# gpg: aka "Aurelien Jarno <aurelien@jarno.fr>"
# gpg: aka "Aurelien Jarno <aurel32@debian.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7746 2642 A9EF 94FD 0F77 196D BA9C 7806 1DDD 8C9B
* remotes/aurel/tags/pull-target-mips-20170717:
target/mips: optimize WSBH, DSBH and DSHD
mips: set CP0 Debug DExcCode for SDBBP instruction
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
target-arm queue:
* new model of the ARM MPS2/MPS2+ FPGA based development board
* clean up DISAS_* exit conditions and fix various regressions
since commits e75449a3468a6b28c7b5 (in particular including
ones which broke OP-TEE guests)
* make Cortex-M3 and M4 correctly default to 8 PMSA regions
# gpg: Signature made Mon 17 Jul 2017 13:43:45 BST
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20170717:
MAINTAINERS: Add entries for MPS2 board
hw/arm/mps2: Add ethernet
hw/arm/mps2: Add SCC
hw/misc/mps2_scc: Implement MPS2 Serial Communication Controller
hw/arm/mps2: Add timers
hw/char/cmsdk-apb-timer: Implement CMSDK APB timer device
hw/arm/mps2: Add UARTs
hw/char/cmsdk-apb-uart.c: Implement CMSDK APB UART
hw/arm/mps2: Implement skeleton mps2-an385 and mps2-an511 board models
target/arm: use DISAS_EXIT for eret handling
target/arm: use gen_goto_tb for ISB handling
target/arm/translate: ensure gen_goto_tb sets exit flags
target/arm/translate.h: expand comment on DISAS_EXIT
target/arm/translate: make DISAS_UPDATE match declared semantics
include/exec/exec-all: document common exit conditions
target/arm: Make Cortex-M3 and M4 default to 8 PMSA regions
qdev: support properties which don't set a default value
qdev-properties.h: Explicitly set the default value for arraylen properties
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The rotation is to the left, but extract shifts to the right.
The computation of the extract parameters needs adjusting.
For the entry condition, simplify
64 - rot + len <= 64
-rot + len <= 0
len <= rot
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reported-by: David Hildenbrand <david@redhat.com>
Suggested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
STFL bit 4 and 5 are just indications to the guest, which TLB entries an
IDTE call will clear. These are performance indicators for the guest.
STFL bit 4:
INVALIDATE DAT TABLE ENTRY (IDTE) performs
the invalidation-and-clearing operation by
selectively clearing TLB segment-table entries
when a segment-table entry or entries are
invalidated. IDTE also performs the clearing-by-
ASCE operation. Unless bit 4 is one, IDTE simply
purges all TLBs. Bit 3 is one if bit 4 is one.
We can simply set STFL bit 4 ("idtes") and still purge the complete TLB.
Purging more than advertised is never bad. E.g. Linux doesn't even care
about this bit. We can optimized this later.
This is helpful, as the z9 base model contains this facility.
STFL bit 5 (clearing TLB region-table-entries) was never implemented on
real HW, therefore we can simply ignore it for now.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170627161032.5014-1-david@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Drop TRT from the set of insns handled internally by EXECUTE.
It's more important to adjust the existing helper to handle
both TRT and TRTR.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Since we require all registers saved on input, read R0 from ENV instead
of passing it manually. Recognize the specification exception when R0
contains incorrect data. Keep high bits of result registers unmodified
when in 31 or 24-bit mode.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Introduce Skylake-Server cpu mode which inherits the features from
Skylake-Client and supports some additional features that are: AVX512,
CLWB and PGPE1GB.
Signed-off-by: Boqun Feng (Intel) <boqun.feng@gmail.com>
Message-Id: <20170621052935.20715-1-boqun.feng@gmail.com>
[ehabkost: copied comment about XSAVES from Skylake-Client]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently when running KVM, we expose "KVMKVMKVM\0\0\0" in
the 0x40000000 CPUID leaf. Other hypervisors (VMWare,
HyperV, Xen, BHyve) all do the same thing, which leaves
TCG as the odd one out.
The CPUID signature is used by software to detect which
virtual environment they are running in and (potentially)
change behaviour in certain ways. For example, systemd
supports a ConditionVirtualization= setting in unit files.
The virt-what command can also report the virt type it is
running on
Currently both these apps have to resort to custom hacks
like looking for 'fw-cfg' entry in the /proc/device-tree
file to identify TCG.
This change thus proposes a signature "TCGTCGTCGTCG" to be
reported when running under TCG.
To hide this, the -cpu option tcg-cpuid=off can be used.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20170509132736.10071-3-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Use the same mask to avoid having to load two different constants.
Suggested-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch fixes setting DExcCode field of CP0 Debug register
when SDBBP instruction is executed. According to EJTAG specification,
this field must be set to the value 9 (Bp).
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-id: 20170502120350.3368.92338.stgit@PASHA-ISP
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Previously DISAS_JUMP did ensure this but with the optimisation of
8a6b28c7 (optimize indirect branches) we might not leave the loop.
This means if any pending interrupts are cleared by changing IRQ flags
we might never get around to servicing them. You usually notice this
by seeing the lookup_tb_ptr() helper gainfully chaining TBs together
while cpu->interrupt_request remains high and the exit_request has not
been set.
This breaks amongst other things the OPTEE test suite which executes
an eret from the secure world after a non-secure world IRQ has gone
pending which then never gets serviced.
Instead of using the previously implied semantics of DISAS_JUMP we use
DISAS_EXIT which will always exit the run-loop.
CC: Etienne Carriere <etienne.carriere@linaro.org>
CC: Joakim Bech <joakim.bech@linaro.org>
CC: Jaroslaw Pelczar <j.pelczar@samsung.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Emilio G. Cota <cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 20170713141928.25419-7-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While an ISB will ensure any raised IRQs happen on the next
instruction it doesn't cause any to get raised by itself. We can
therefore use a simple tb exit for ISB instructions and rely on the
exit_request check at the top of each TB to deal with exiting if
needed.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 20170713141928.25419-6-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
DISAS_UPDATE should be used when the wider CPU state other than just
the PC has been updated and we should therefore exit the TCG runtime
and return to the main execution loop rather assuming DISAS_JUMP would
do that.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 20170713141928.25419-3-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-M3 and M4 CPUs always have 8 PMSA MPU regions (this isn't
a configurable option for the hardware). Make the default value of
the pmsav7-dregion property be set per-cpu, so we don't need to have
every user of these CPUs set it manually. (The existing default of
16 is correct for the other PMSAv7 core, the Cortex-R5.)
This fixes a bug where we were creating the M3 and M4 with
too many regions; most guest software would not notice or
care, though, since it would just not use the registers
associated with the unexpected extra regions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1499788408-10096-4-git-send-email-peter.maydell@linaro.org
But when a guest initializes radix mode, it issues a H_REGISTER_PROC_TBL
to update the LPCR of all CPUs. Hot-plugged CPUs inherit from the same
setting under KVM but not under TCG. So, Let's check for radix and update
the default LPCR to keep new CPUs in sync.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So far, qemu implements the PAPR Hash Page Table (HPT) resizing extension
with TCG. The same implementation will work with KVM PR, but we don't
currently allow that. For KVM HV we can only implement resizing with the
assistance of the host kernel, which needs a new capability and ioctl()s.
This patch adds support for testing the new KVM capability and implementing
the resize in terms of KVM facilities when necessary. If we're running on
a kernel which doesn't have the new capability flag at all, we fall back to
testing for PR vs. HV KVM using the same hack that we already use in a
number of places for older kernels.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
