The maximum padding size is either 64 or 128 bytes and should always be smaller
than "req_len". If "padding_size" exceeds "req_len", then
"req_len - padding_size" underflows due to "uint32_t" data type, leading to a
large incorrect value (e.g., `0xFFXXXXXX`). This causes an out-of-bounds memory
access, potentially leading to a buffer overflow.
Added a check to ensure "padding_size" does not exceed "req_len" before
computing "pad_offset". This prevents "req_len - padding_size" from underflowing
and avoids accessing invalid memory.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Fixes: 5cd7d8564a ("aspeed/hace: Support AST2600 HACE ")
Link: https://lore.kernel.org/qemu-devel/20250321092623.2097234-3-jamin_lin@aspeedtech.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit 78877b2e06)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add .set_vnet_le() function that always returns success, assuming that
vDPA h/w always implements LE data format. Otherwise, QEMU disables vDPA and
outputs the message:
"backend does not support LE vnet headers; falling back on userspace virtio"
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit b027f55a99)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The check for fp_excp_el in assert_fp_access_checked is
incorrect. For SME, with StreamingMode enabled, the access
is really against the streaming mode vectors, and access
to the normal fp registers is allowed to be disabled.
C.f. sme_enabled_check.
Convert sve_access_checked to match, even though we don't
currently check the exception state.
Cc: qemu-stable@nongnu.org
Fixes: 3d74825f4d ("target/arm: Add SME enablement checks")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250307190415.982049-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 298a04998f)
(Mjt: minor context fix in target/arm/tcg/translate.h,
target/arm/tcg/translate-a64.c is target/arm/translate-a64.c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On ARM hosts with CTR_EL0.DIC and CTR_EL0.IDC set, this would only cause
an ISB to be executed during cache maintenance, which could lead to QEMU
executing TBs containing garbage instructions.
This seems to be because the ISB finishes executing instructions and
flushes the pipeline, but the ISB doesn't guarantee that writes from the
executed instructions are committed. If a small enough TB is created, it's
possible that the writes setting up the TB aren't committed by the time the
TB is executed.
This function is intended to be a port of the gcc implementation
(85b46d0795/libgcc/config/aarch64/sync-cache.c (L67))
which makes the first DSB unconditional, so we can fix the synchronization
issue by doing that as well.
Cc: qemu-stable@nongnu.org
Fixes: 664a79735e ("util: Specialize flush_idcache_range for aarch64")
Signed-off-by: Joe Komlodi <komlodi@google.com>
Message-id: 20250310203622.1827940-2-komlodi@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit e6c38d2ab5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
These warnings are breaking some build configurations since 2 months
now (https://gitlab.com/qemu-project/qemu/-/issues/2575):
ui/cocoa.m:662:14: error: 'CVDisplayLinkCreateWithCGDisplay' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
662 | if (!CVDisplayLinkCreateWithCGDisplay(display, &displayLink)) {
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:89:20: note: 'CVDisplayLinkCreateWithCGDisplay' has been explicitly marked deprecated here
89 | CV_EXPORT CVReturn CVDisplayLinkCreateWithCGDisplay(
| ^
ui/cocoa.m:663:29: error: 'CVDisplayLinkGetNominalOutputVideoRefreshPeriod' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
663 | CVTime period = CVDisplayLinkGetNominalOutputVideoRefreshPeriod(displayLink);
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:182:18: note: 'CVDisplayLinkGetNominalOutputVideoRefreshPeriod' has been explicitly marked deprecated here
182 | CV_EXPORT CVTime CVDisplayLinkGetNominalOutputVideoRefreshPeriod( CVDisplayLinkRef CV_NONNULL displayLink );
| ^
ui/cocoa.m:664:13: error: 'CVDisplayLinkRelease' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
664 | CVDisplayLinkRelease(displayLink);
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:249:16: note: 'CVDisplayLinkRelease' has been explicitly marked deprecated here
249 | CV_EXPORT void CVDisplayLinkRelease( CV_RELEASES_ARGUMENT CVDisplayLinkRef CV_NULLABLE displayLink );
| ^
3 errors generated.
For the next release, ignore the warnings using #pragma directives.
At least until we figure the correct new API usage.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Phil Dennis-Jordan <phil@philjordan.eu>
Tested-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-Id: <20241121131954.98949-1-philmd@linaro.org>
(cherry picked from commit 9cf6e41fe2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Block drivers assume in their .bdrv_open() implementation that their
state in bs->opaque has been zeroed; it is initially allocated with
g_malloc0() in bdrv_open_driver().
bdrv_snapshot_goto() needs to make sure that it is zeroed again before
calling drv->bdrv_open() to avoid that block drivers use stale values.
One symptom of this bug is VMDK running into a double free when the user
tries to apply an internal snapshot like 'qemu-img snapshot -a test
test.vmdk'. This should be a graceful error because VMDK doesn't support
internal snapshots.
==25507== Invalid free() / delete / delete[] / realloc()
==25507== at 0x484B347: realloc (vg_replace_malloc.c:1801)
==25507== by 0x54B592A: g_realloc (gmem.c:171)
==25507== by 0x1B221D: vmdk_add_extent (../block/vmdk.c:570)
==25507== by 0x1B1084: vmdk_open_sparse (../block/vmdk.c:1059)
==25507== by 0x1AF3D8: vmdk_open (../block/vmdk.c:1371)
==25507== by 0x1A2AE0: bdrv_snapshot_goto (../block/snapshot.c:299)
==25507== by 0x205C77: img_snapshot (../qemu-img.c:3500)
==25507== by 0x58FA087: (below main) (libc_start_call_main.h:58)
==25507== Address 0x832f3e0 is 0 bytes inside a block of size 272 free'd
==25507== at 0x4846B83: free (vg_replace_malloc.c:989)
==25507== by 0x54AEAC4: g_free (gmem.c:208)
==25507== by 0x1AF629: vmdk_close (../block/vmdk.c:2889)
==25507== by 0x1A2A9C: bdrv_snapshot_goto (../block/snapshot.c:290)
==25507== by 0x205C77: img_snapshot (../qemu-img.c:3500)
==25507== by 0x58FA087: (below main) (libc_start_call_main.h:58)
This error was discovered by fuzzing qemu-img.
Cc: qemu-stable@nongnu.org
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2853
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2851
Reported-by: Denis Rastyogin <gerben@altlinux.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20250310104858.28221-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit b75c5f9879)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For accesses to the 91c111 data register, the address within the
packet's data frame is determined by a combination of the pointer
register and the offset used to access the data register, so that you
can access data at effectively wider than byte width. The pointer
register's pointer field is 11 bits wide, which is exactly the size
to index a 2048-byte data frame.
We weren't quite getting the logic right for ensuring that we end up
with a pointer value to use in the s->data[][] array that isn't out
of bounds:
* we correctly mask when getting the initial pointer value
* for the "autoincrement the pointer register" case, we
correctly mask after adding 1 so that the pointer register
wraps back around at the 2048 byte mark
* but for the non-autoincrement case where we have to add the
low 2 bits of the data register offset, we don't account
for the possibility that the pointer register is 0x7ff
and the addition should wrap
Fix this bug by factoring out the "get the p value to use as an array
index" into a function, making it use FIELD macro names rather than
hard-coded constants, and having a utility function that does "add a
value and wrap it" that we can use both for the "autoincrement" and
"add the offset bits" codepaths.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2758
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228191652.1957208-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 700d3d6dd4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the smc91c111 transmits a packet, it must read a control byte
which is at the end of the data area and CRC. However, we don't
sanitize the length field in the packet buffer, so if the guest sets
the length field to something large we will try to read past the end
of the packet data buffer when we access the control byte.
As usual, the datasheet says nothing about the behaviour of the
hardware if the guest misprograms it in this way. It says only that
the maximum valid length is 2048 bytes. We choose to log the guest
error and silently drop the packet.
This requires us to factor out the "mark the tx packet as complete"
logic, so we can call it for this "drop packet" case as well as at
the end of the loop when we send a valid packet.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2742
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228174802.1945417-3-peter.maydell@linaro.org>
[PMD: Update smc91c111_do_tx() as len > MAX_PACKET_SIZE]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit aad6f264ad)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The smc91c111 uses packet numbers as an index into its internal
s->data[][] array. Valid packet numbers are between 0 and 3, but
the code does not generally check this, and there are various
places where the guest can hand us an arbitrary packet number
and cause an out-of-bounds access to the data array.
Add validation of packet numbers. The datasheet is not very
helpful about how guest errors like this should be handled:
it says nothing on the subject, and none of the documented
error conditions are relevant. We choose to log the situation
with LOG_GUEST_ERROR and silently ignore the attempted operation.
In the places where we are about to access the data[][] array
using a packet number and we know the number is valid because
we got it from somewhere that has already validated, we add
an assert() to document that belief.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228174802.1945417-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 2fa3a5b946)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The SMC91C111 includes an MMU Command register which permits
the guest to remove entries from the RX FIFO. The datasheet
does not specify what happens if the guest tries to do this
when the FIFO is already empty; there are no status registers
containing error bits which might be applicable.
Currently we don't guard at all against pop of an empty
RX FIFO, with the result that we allow the guest to drive
the rx_fifo_len index to negative values, which will cause
smc91c111_receive() to write to the rx_fifo[] array out of
bounds when we receive the next packet.
Instead ignore attempts to pop an empty RX FIFO.
Cc: qemu-stable@nongnu.org
Fixes: 80337b66a8 ("NIC emulation for qemu arm-softmmu")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2780
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250207151157.3151776-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 937df81af6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The commit to fix the OCC common area sensor mappings didn't update the
register offsets to match.
Before this change, skiboot reports:
[ 0.347100086,3] OCC: Chip 0 sensor data invalid
Afterward, there is no error and the sensor_groups directory appears
under /sys/firmware/opal/.
The SLW_IMAGE_BASE address looks like a workaround to intercept firmware
memory accesses, but that does not seem to be required now (and would
have been broken by the OCC common area region mapping change anyway).
So it can be removed.
Fixes: 3a1b70b66b ("ppc/pnv: Fix OCC common area region mapping")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 29c041ca7f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This error was discovered by fuzzing qemu-img.
In the QED block driver, the need_check_timer timer is freed in
bdrv_qed_detach_aio_context, but the pointer to the timer is not
set to NULL. This can lead to a use-after-free scenario
in bdrv_qed_drain_begin().
The need_check_timer pointer is set to NULL after freeing the timer.
Which helps catch this condition when checking in bdrv_qed_drain_begin().
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2852
Signed-off-by: Denis Rastyogin <gerben@altlinux.org>
Message-ID: <20250304083927.37681-1-gerben@altlinux.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 2ad638a3d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Instead of migrating the raw tick_offset, goldfish_rtc migrates a
recalculated value based on QEMU_CLOCK_VIRTUAL. As QEMU_CLOCK_VIRTUAL
stands still across a save-and-restore cycle, the guest RTC becomes out
of sync with the host RTC when the VM is restored.
As described in the bug description, it looks like this calculation was
copied from pl031 RTC, which had its tick_offset migration fixed by
Commit 032cfe6a79 ("pl031: Correctly migrate state when using -rtc
clock=host").
Migrate the tick_offset directly, adding it as a version-dependent field
to VMState. Keep the old behavior when migrating from previous versions.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2033
Signed-off-by: Rodrigo Dias Correa <r@drigo.nl>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250114212150.228241-1-r@drigo.nl>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 3521f9cadc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the RISC-V privileged ISA section 3.1.15 table 15, it is determined
that a debug exception that is triggered from a load/store has a higher
priority than a possible fault that this access might trigger.
This is not the case ATM as shown in [1]. Adding a breakpoint in an
address that deliberately will fault is causing a load page fault
instead of a debug exception. The reason is that we're throwing in the
page fault as soon as the fault occurs (end of riscv_cpu_tlb_fill(),
raise_mmu_exception()), not allowing the installed watchpoints to
trigger.
Call cpu_check_watchpoint() in the page fault path to search and execute
any watchpoints that might exist for the address, never returning back
to the fault path. If no watchpoints are found cpu_check_watchpoint()
will return and we'll fall-through the regular path to
raise_mmu_exception().
[1] https://gitlab.com/qemu-project/qemu/-/issues/2627
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2627
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250121170626.1992570-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit c86edc5476)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The mcontrol select bit (19) is always zero, meaning our triggers will
always match virtual addresses. In this condition, if the user does not
specify a size for the trigger, the access size defaults to XLEN.
At this moment we're using def_size = 8 regardless of CPU XLEN. Use
def_size = 4 in case we're running 32 bits.
Fixes: 95799e36c1 ("target/riscv: Add initial support for the Sdtrig extension")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250121170626.1992570-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 3fba76e61c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the Vector Reduction Operations section in the RISC-V "V"
Vector Extension spec,
"If vl=0, no operation is performed and the destination register is not
updated."
The vd should be updated when vl is larger than 0.
Fixes: fe5c9ab1fc ("target/riscv: vector single-width integer reduction instructions")
Fixes: f714361ed7 ("target/riscv: rvv-1.0: implement vstart CSR")
Signed-off-by: Max Chou <max.chou@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20250124101452.2519171-1-max.chou@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit ffd455963f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The function `vhost_dev_init()` expects the `struct vhost_dev`
(passed as a parameter) to be fully initialized. This is important
because some parts of the code check whether `vhost_dev->config_ops`
is NULL to determine if it has been set (e.g. later via
`vhost_dev_set_config_notifier`).
To ensure this initialization, it’s better to allocate the entire
`CryptoDevBackendVhost` structure (which includes `vhost_dev`) using
`g_mem0()`, following the same approach used for other vhost devices,
such as in `vhost_net_init()`.
Fixes: 042cea274c ("cryptodev: add vhost-user as a new cryptodev backend")
Cc: qemu-stable@nongnu.org
Reported-by: myluo24@m.fudan.edu.cn
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20250211135523.101203-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 83cb18ac45)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
AMD IOMMU provides the base address of control registers through
IVRS table and PCI capability. Since this base address is of 64 bit,
use 32 bits mask (instead of 16 bits) to set BAR low and high.
Fixes: d29a09ca68 ("hw/i386: Introduce AMD IOMMU")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250207045354.27329-3-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 3684717b74)
(Mjt: adjust for 7.2.x)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
By accessing MemoryRegion internals, amdvi_init() gives the false
idea that the PCI BAR can be modified. However this isn't true
(at least the model isn't ready for that): the device is explicitly
maps at the BAR at the fixed AMDVI_BASE_ADDR address in
amdvi_sysbus_realize(). Since the SysBus API isn't designed to
remap regions, directly use the fixed address in amdvi_init().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230313153031.86107-3-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 6291a28645)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Interrupt passthrough is determine by the bits 191,190,187-184.
These bits are part of the 3rd quad word (i.e. index 2) in DTE. Hence
replace dte[3] by dte[2].
Fixes: b44159fe0 ("x86_iommu/amd: Add interrupt remap support when VAPIC is not enabled")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250207045354.27329-2-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 63dc0b8647)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
TYPE_CHIPIDEA models an IP block which is also used in TYPE_ZYNQ_MACHINE which
itself is not an IMX device. CONFIG_ZYNQ selects CONFIG_USB_EHCI_SYSBUS while
TYPE_CHIPIDEA is a separate compilation unit, so only works by accident if
CONFIG_IMX is given. Fix that by extracting CONFIG_USB_CHIPIDEA from CONFIG_IMX.
cc: qemu-stable@nongnu.org
Fixes: 616ec12d0f "hw/arm/xilinx_zynq: Fix USB port instantiation"
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-id: 20250209103604.29545-1-shentey@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 464ce71a96)
(Mjt: context fixup due to missing
v8.0.0-1939-gde6cd7599b51 "meson: Replace softmmu_ss -> system_ss",
v9.1.0-609-ge02491903d50 "hw/usb: Remove tusb6010 USB controller",
v9.2.0-1303-g1b326f278d05 "hw/pci-host/designware: Expose MSI IRQ")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the gicv3_{irq,fiq,irqfiq}_access() functions, there is a check
which downgrades a CP_ACCESS_TRAP_EL3 to CP_ACCESS_TRAP if EL3 is not
AArch64. This has been there since the GIC was first implemented,
but it isn't right: if we are trapping because of SCR.IRQ or SCR.FIQ
then we definitely want to be going to EL3 (doing
AArch32.TakeMonitorTrapException() in pseudocode terms). We might
want to not take a trap at all, but we don't ever want to go to the
default target EL, because that would mean, for instance, taking a
trap to Hyp mode if the trapped access was made from Hyp mode.
(This might have been an attempt to work around our failure to
properly implement Monitor Traps.)
Remove the bogus check.
Cc: qemu-stable@nongnu.org
Fixes: 359fbe65e0 ("hw/intc/arm_gicv3: Implement GICv3 CPU interface registers")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-7-peter.maydell@linaro.org
(cherry picked from commit d04c6c3c00)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In system register access pseudocode the common pattern for
AArch32 registers with access traps to EL3 is:
at EL1 and EL2:
if HaveEL(EL3) && !ELUsingAArch32(EL3) && (SCR_EL3.TERR == 1) then
AArch64.AArch32SystemAccessTrap(EL3, 0x03);
elsif HaveEL(EL3) && ELUsingAArch32(EL3) && (SCR.TERR == 1) then
AArch32.TakeMonitorTrapException();
at EL3:
if (PSTATE.M != M32_Monitor) && (SCR.TERR == 1) then
AArch32.TakeMonitorTrapException();
(taking as an example the ERRIDR access pseudocode).
This implements the behaviour of (in this case) SCR.TERR that
"Accesses to the specified registers from modes other than Monitor
mode generate a Monitor Trap exception" and of SCR_EL3.TERR that
"Accesses of the specified Error Record registers at EL2 and EL1
are trapped to EL3, unless the instruction generates a higher
priority exception".
In QEMU we don't implement this pattern correctly in two ways:
* in access_check_cp_reg() we turn the CP_ACCESS_TRAP_EL3 into
an UNDEF, not a trap to Monitor mode
* in the access functions, we check trap bits like SCR.TERR
only when arm_current_el(env) < 3 -- this is correct for
AArch64 EL3, but misses the "trap non-Monitor-mode execution
at EL3 into Monitor mode" case for AArch32 EL3
In this commit we fix the first of these two issues, by
making access_check_cp_reg() handle CP_ACCESS_TRAP_EL3
as a Monitor trap. This is a kind of exception that we haven't
yet implemented(!), so we need a new EXCP_MON_TRAP for it.
This diverges from the pseudocode approach, where every access check
function explicitly checks for "if EL3 is AArch32" and takes a
monitor trap; if we wanted to be closer to the pseudocode we could
add a new CP_ACCESS_TRAP_MONITOR and make all the accessfns use it
when appropriate. But because there are no non-standard cases in the
pseudocode (i.e. where either it raises a Monitor trap that doesn't
correspond to an AArch64 SystemAccessTrap or where it raises a
SystemAccessTrap that doesn't correspond to a Monitor trap), handling
this all in one place seems less likely to result in future bugs
where we forgot again about this special case when writing an
accessor.
(The cc of stable here is because "hw/intc/arm_gicv3_cpuif: Don't
downgrade monitor traps for AArch32 EL3" which is also cc:stable
will implicitly use the new EXCP_MON_TRAP code path.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-6-peter.maydell@linaro.org
(cherry picked from commit 4cf4948651)
(Mjt: context fix due to missing
v9.0.0-151-gb36a32ead159 "target/arm: Add support for Non-maskable Interrupt",
v8.0.0-2011-g11b76fda0adc "target/arm: Implement GPC exceptions")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The pseudocode for AT S1E2R and AT S1E2W says that they should be
UNDEFINED if executed at EL3 when EL2 is not enabled. We were
incorrectly using CP_ACCESS_TRAP and reporting the wrong exception
syndrome as a result. Use CP_ACCESS_TRAP_UNCATEGORIZED.
Cc: qemu-stable@nongnu.org
Fixes: 2a47df9532 ("target-arm: Wire up AArch64 EL2 and EL3 address translation ops")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-4-peter.maydell@linaro.org
(cherry picked from commit ccda792945)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The access pseudocode for the CNTPS_TVAL_EL1, CNTPS_CTL_EL1 and
CNTPS_CVAL_EL1 secure timer registers says that they are UNDEFINED
from EL2 or NS EL1. We incorrectly return CP_ACCESS_TRAP from the
access function in these cases, which means that we report the wrong
syndrome value to the target EL.
Use CP_ACCESS_TRAP_UNCATEGORIZED, which reports the correct syndrome
value for an UNDEFINED instruction.
Cc: qemu-stable@nongnu.org
Fixes: b4d3978c2f ("target-arm: Add the AArch64 view of the Secure physical timer")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-2-peter.maydell@linaro.org
(cherry picked from commit b819fd6994)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The gdbstub implementation for the Sparc architecture would
incorrectly calculate the the floating point register offset.
This resulted in, for example, registers f32 and f34 to point to
the same value.
The issue was caused by the confusion between even register numbers
and even register indexes. For example, the register index of f32 is 64
and f34 is 65.
Cc: qemu-stable@nongnu.org
Fixes: 30038fd818 ("target-sparc: Change fpr representation to doubles.")
Signed-off-by: Mikael Szreder <git@miszr.win>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250214070343.11501-1-git@miszr.win>
(cherry picked from commit 7a74e46808)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Windows only:
The libSDL2 Windows message loop needs the libSDL2 Windows low
level keyboard hook procedure to grab the left and right Windows
keys correctly. Reenable the SDL2 Windows keyboard hook procedure.
Since SDL2 2.30.4 the SDL2 keyboard hook procedure also filters
out the special left Control key event for every Alt Gr key event
on keyboards with an international layout. This means the QEMU low
level keyboard hook procedure is no longer needed. Remove the QEMU
Windows keyboard hook procedure.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2139
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2323
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Link: https://lore.kernel.org/r/20241231115950.6732-1-vr_qemu@t-online.de
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 4dafba778a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix in ui/sdl2.c and adaptation in ui/meson.build)
When USBPacket in OUT direction has larger payload
than the ep_out_buffer (of size 512), a buffer overflow
would occur.
It could be fixed by limiting the size of usb_packet_copy
to be at most buffer size. Further optimization gets rid
of the ep_out_buffer and directly uses ep_out as the target
buffer.
This is reported by a security researcher who artificially
constructed an OUT packet of size 2047. The report has gone
through the QEMU security process, and as this device is for
testing purpose and no deployment of it in virtualization
environment is observed, it is triaged not to be a security bug.
Cc: qemu-stable@nongnu.org
Fixes: d7d3491855 ("hw/usb: Add CanoKey Implementation")
Reported-by: Juan Jose Lopez Jaimez <thatjiaozi@gmail.com>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Message-id: Z4TfMOrZz6IQYl_h@Sun
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 664280abdd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The pseudocode ResetSVEState() does:
FPSR = ZeroExtend(0x0800009f<31:0>, 64);
but QEMU's arm_reset_sve_state() called vfp_set_fpcr() by accident.
Before the advent of FEAT_AFP, this was only setting a collection of
RES0 bits, which vfp_set_fpsr() would then ignore, so the only effect
was that we didn't actually set the FPSR the way we are supposed to
do. Once FEAT_AFP is implemented, setting the bottom bits of FPSR
will change the floating point behaviour.
Call vfp_set_fpsr(), as we ought to.
(Note for stable backports: commit 7f2a01e736 moved this function
from sme_helper.c to helper.c, but it had the same bug before the
move too.)
Cc: qemu-stable@nongnu.org
Fixes: f84734b874 ("target/arm: Implement SMSTART, SMSTOP")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250124162836.2332150-4-peter.maydell@linaro.org
(cherry picked from commit 1edc3d43f2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(it is in sme_helper.c in 7.2, not in helper.c)
Current versions of Windows call _DSM(func=7) regardless
of whether it is supported or not. It leads to NICs having bogus
'PCI Label Id = 0', where none should be set at all.
Also presence of 'PCI Label Id' triggers another Windows bug
on localized versions that leads to hangs. The later bug is fixed
in latest updates for 'Windows Server' but not in consumer
versions of Windows (and there is no plans to fix it
as far as I'm aware).
Given it's easy, implement Microsoft suggested workaround
(return invalid Package) so that affected Windows versions
could boot on QEMU.
This would effectvely remove bogus 'PCI Label Id's on NICs,
but MS teem confirmed that flipping 'PCI Label Id' should not
change 'Network Connection' ennumeration, so it should be safe
for QEMU to change _DSM without any compat code.
Smoke tested with WinXP and WS2022
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/774
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20250115125342.3883374-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 0b05339198)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The end vector calculation has a bug that results in polling fewer
than required vectors when reading at a non-zero offset in PBA memory.
Fixes: bbef882cc1 ("msi: add API to get notified about pending bit poll")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20241212120402.1475053-1-npiggin@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 42e2a7a0ab)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
PCI hotplug for downstream endpoints on arm fails because Linux'
PCIe hotplug driver doesn't like the QEMU provided LNKSTA:
pcieport 0000:08:01.0: pciehp: Slot(2): Card present
pcieport 0000:08:01.0: pciehp: Slot(2): Link Up
pcieport 0000:08:01.0: pciehp: Slot(2): Cannot train link: status 0x2000
There's 2 cases where LNKSTA isn't setup properly:
* the downstream device has no express capability
* max link width of the bridge is 0
Move the sanity checks added via 88c869198a
("pci: Sanity test minimum downstream LNKSTA") outside of the
branch to make sure downstream ports always have a valid LNKSTA.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-Id: <20241203121928.14861-1-sebott@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 694632fd44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU would crash with a failed assertion if the XHCI controller
attempted to raise the interrupt on an interrupter corresponding
to a MSI vector with a higher index than the highest configured
for the device by the guest driver.
This behaviour is correct on the MSI/PCI side: per PCI 3.0 spec,
devices must ensure they do not send MSI notifications for
vectors beyond the range of those allocated by the system/driver
software. Unlike MSI-X, there is no generic way for handling
aliasing in the case of fewer allocated vectors than requested,
so the specifics are up to device implementors. (Section
6.8.3.4. "Sending Messages")
It turns out the XHCI spec (Implementation Note in section 4.17,
"Interrupters") requires that the host controller signal the MSI
vector with the number computed by taking the interrupter number
modulo the number of enabled MSI vectors.
This change introduces that modulo calculation, fixing the
failed assertion. This makes the device work correctly in MSI mode
with macOS's XHCI driver, which only allocates a single vector.
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250112210056.16658-2-phil@philjordan.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit bb5b7fced6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
TCG trace-events were deprecated before the v6.2 release,
and removed for v7.0.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit b4859e8f33)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
KVM is not happy when starting a VM with weird RAM sizes:
# qemu-system-s390x --enable-kvm --nographic -m 1234K
qemu-system-s390x: kvm_set_user_memory_region: KVM_SET_USER_MEMORY_REGION
failed, slot=0, start=0x0, size=0x244000: Invalid argument
kvm_set_phys_mem: error registering slot: Invalid argument
Aborted (core dumped)
Let's handle that in a better way by rejecting such weird RAM sizes
right from the start:
# qemu-system-s390x --enable-kvm --nographic -m 1234K
qemu-system-s390x: ram size must be multiples of 1 MiB
Message-ID: <20241219144115.2820241-2-david@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
(cherry picked from commit 14e568ab48)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The macOS builds in our CI (and possibly other very recent distros)
are currently broken since the update to libnfs version 6 there.
That version apparently comes with a big API breakage. v5.0.3 was
the final release of the old API (see the libnfs commit here:
https://github.com/sahlberg/libnfs/commit/4379837 ).
Disallow version 6.x for now to get the broken CI job working
again. Once somebody had enough time to adapt our code in
block/nfs.c, we can revert this change again.
Message-ID: <20241218065157.209020-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e2d98f2571)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup)
In the GICv3 ITS model, we have a common coding pattern which has a
local C struct like "DTEntry dte", which is a C representation of an
in-guest-memory data structure, and we call a function such as
get_dte() to read guest memory and fill in the C struct. These
functions to read in the struct sometimes have cases where they will
leave early and not fill in the whole struct (for instance get_dte()
will set "dte->valid = false" and nothing else for the case where it
is passed an entry_addr implying that there is no L2 table entry for
the DTE). This then causes potential use of uninitialized memory
later, for instance when we call a trace event which prints all the
fields of the struct. Sufficiently advanced compilers may produce
-Wmaybe-uninitialized warnings about this, especially if LTO is
enabled.
Rather than trying to carefully separate out these trace events into
"only the 'valid' field is initialized" and "all fields can be
printed", zero-init all the structs when we define them. None of
these structs are large (the biggest is 24 bytes) and having
consistent behaviour is less likely to be buggy.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2718
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241213182337.3343068-1-peter.maydell@linaro.org
(cherry picked from commit 9678b9c505)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If the binary loaded via -kernel is *not* a linux kernel (in which
case protocol == 0), do not patch the linux kernel header fields.
It's (a) pointless and (b) might break binaries by random patching
and (c) changes the binary hash which in turn breaks secure boot
verification.
Background: OVMF happily loads and runs not only linux kernels but
any efi binary via direct kernel boot.
Note: Breaking the secure boot verification is a problem for linux
kernels too, but fixed that is left for another day ...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-ID: <20240905141211.1253307-3-kraxel@redhat.com>
(cherry picked from commit 57e2cc9abf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: it is in hw/i386/x86.c not hw/i386/x86-common.c in 7.2.x)
We used to only have a single UART on the platform and it was located at
address 0x90000000. When the number of UARTs was increased to 4, the
first UART remained at it's location, but instead of being the first one
to be registered, it became the last.
This caused QEMU to pick 0x90000300 as the default UART, which broke
software that hardcoded the address of 0x90000000 and expected it's
output to be visible when the user configured only a single console.
This caused regressions[1] in the barebox test suite when updating to a
newer QEMU. As there seems to be no good reason to register the UARTs in
inverse order, let's register them by ascending address, so existing
software can remain oblivious to the additional UART ports.
Changing the order of uart registration alone breaks Linux which
was choosing the UART at 0x90000300 as the default for ttyS0. To fix
Linux we fix three things in the device tree:
1. Define stdout-path only one time for the first registered UART
instead of incorrectly defining for each UART.
2. Change the UART alias name from 'uart0' to 'serial0' as almost all
Linux tty drivers look for an alias starting with "serial".
3. Add the UART nodes so they appear in the final DTB in the
order starting with the lowest address and working upwards.
In summary these changes mean that the QEMU default UART (serial_hd(0))
is now setup where:
* serial_hd(0) is the lowest-address UART
* serial_hd(0) is listed first in the DTB
* serial_hd(0) is the /chosen/stdout-path one
* the /aliases/serial0 alias points at serial_hd(0)
[1]: https://lore.barebox.org/barebox/707e7c50-aad1-4459-8796-0cc54bab32e2@pengutronix.de/T/#m5da26e8a799033301489a938b5d5667b81cef6ad
Fixes: 777784bda4 ("hw/openrisc: support 4 serial ports in or1ksim")
Cc: qemu-stable@nongnu.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
[stafford: Change to serial0 alias and update change message, reverse
uart registration order]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 26dcf2be7e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ppc (pnv and spapr) NMI injection code does not go through the
asynchronous interrupt path and set a bit in env->pending_interrupts
and raise an interrupt request that the cpu_exec() loop can see.
Instead it injects the exception directly into registers.
This can lead to cpu_exec() missing that the thread has work to do,
if a NMI is injected while it was idle.
Fix this by clearing halted when injecting the interrupt. Probably
NMI injection should be reworked to use the interrupt request interface,
but this seems to work as a minimal fix.
Fixes: 3431648272 ("spapr: Add support for new NMI interface")
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit fa416ae615)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
With a valid file ID (FID) of an open file, it should be possible to send
a 'Tgettattr' 9p request and successfully receive a 'Rgetattr' response,
even if the file has been removed in the meantime. Currently this would
fail with ENOENT.
I.e. this fixes the following misbehaviour with a 9p Linux client:
open("/home/tst/filename", O_RDWR|O_CREAT|O_EXCL, 0600) = 3
unlink("/home/tst/filename") = 0
fstat(3, 0x23aa1a8) = -1 ENOENT (No such file or directory)
Expected results:
open("/home/tst/filename", O_RDWR|O_CREAT|O_EXCL, 0600) = 3
unlink("/home/tst/filename") = 0
fstat(3, {st_mode=S_IFREG|0600, st_size=0, ...}) = 0
This is because 9p server is always using a path name based lstat() call
which fails as soon as the file got removed. So to fix this, use fstat()
whenever we have an open file descriptor already.
Fixes: 00ede4c252 ("virtio-9p: getattr server implementation...")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/103
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <4c41ad47f449a5cc8bfa9285743e029080d5f324.1732465720.git.qemu_oss@crudebyte.com>
(cherry picked from commit c81e7219e0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After removing a file from the file system, we should still be able to
work with the file if we already had it open before removal.
As a first step we verify that it is possible to write to an unlinked
file, as this is what already works. This test is extended later on
after having fixed other use cases after unlink that are not working
yet.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <3d6449d4df25bcdd3e807eff169f46f1385e5257.1732465720.git.qemu_oss@crudebyte.com>
(cherry picked from commit 462db8fb1d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix, pick it to stable so the next patch in this place applies)
The libssh does not handle non-blocking mode in SFTP correctly. The
driver code already changes the mode to blocking for the SFTP
initialization, but for some reason changes to non-blocking mode.
This used to work accidentally until libssh in 0.11 branch merged
the patch to avoid infinite looping in case of network errors:
https://gitlab.com/libssh/libssh-mirror/-/merge_requests/498
Since then, the ssh driver in qemu fails to read files over SFTP
as the first SFTP messages exchanged after switching the session
to non-blocking mode return SSH_AGAIN, but that message is lost
int the SFTP internals and interpretted as SSH_ERROR, which is
returned to the caller:
https://gitlab.com/libssh/libssh-mirror/-/issues/280
This is indeed an issue in libssh that we should address in the
long term, but it will require more work on the internals. For
now, the SFTP is not supported in non-blocking mode.
Fixes: https://gitlab.com/libssh/libssh-mirror/-/issues/280
Signed-off-by: Jakub Jelen <jjelen@redhat.com>
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-ID: <20241113125526.2495731-1-rjones@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit fbdea3d6c1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
pci_devfn properties accept either a string or an integer as input. To
implement this, set_pci_devfn() first tries to visit the option as a
string, and if that fails, it visits it as an integer instead. While the
QemuOpts visitor happens to accept this, it is invalid according to the
visitor interface. QObject input visitors run into an assertion failure
when this is done.
QObject input visitors are used with the JSON syntax version of -device
on the command line:
$ ./qemu-system-x86_64 -enable-kvm -M q35 -device pcie-pci-bridge,id=pci.1,bus=pcie.0 -blockdev null-co,node-name=disk -device '{ "driver": "virtio-blk-pci", "drive": "disk", "id": "virtio-disk0", "bus": "pci.1", "addr": 1 }'
qemu-system-x86_64: ../qapi/qobject-input-visitor.c:143: QObject *qobject_input_try_get_object(QObjectInputVisitor *, const char *, _Bool): Assertion `removed' failed.
The proper way to accept both strings and integers is using the
alternate mechanism, which tells us the type of the input before it's
visited. With this information, we can directly visit it as the right
type.
This fixes set_pci_devfn() by using the alternate mechanism.
Cc: qemu-stable@nongnu.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20241119120353.57812-1-kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 5102f9df4a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
work_around_broken_dhclient() accesses IP and UDP headers to detect
relevant packets and to calculate checksums, but it didn't check if
the packet has size sufficient to accommodate them, causing out-of-bound
access hazards. Fix this by correcting the size requirement.
Fixes: 1d41b0c1ec ("Work around dhclient brokenness")
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit a8575f7fb2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
- Various developers are reluctant to git Cirrus-CI the permissions
requested to access their GitHub account.
- When we use the cirrus-run script to trigger Cirrus-CI job from
GitLab-CI, the GitLab-CI job is restricted to a 1h timeout
(often not enough).
- Although Cirrus-CI VMs are more powerful than GitLab-CI ones,
its free plan is limited in 2 concurrent jobs.
- The GitLab-CI MSYS2 jobs are a 1:1 mapping with the Cirrus-CI ones
(modulo the environment caching).
Reduce the maintenance burden by removing the Cirrus-CI config file,
keeping the GitLab-CI jobs.
Update Yonggang Luo's maintenance file list to the new file, which
use the same environment shell.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230322135721.61138-3-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit da80f11efe)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: ignore previous changes in .cirrus.yml since it is being removed anyway)
In extioi_setirq() we try to operate on a bit array stored as an
array of uint32_t using the set_bit() and clear_bit() functions
by casting the pointer to 'unsigned long *'.
This has two problems:
* the alignment of 'uint32_t' is less than that of 'unsigned long'
so we pass an insufficiently aligned pointer, which is
undefined behaviour
* on big-endian hosts the 64-bit 'unsigned long' will have
its two halves the wrong way around, and we will produce
incorrect results
The undefined behaviour is shown by the clang undefined-behaviour
sanitizer when running the loongarch64-virt functional test:
/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/qemu/bitops.h:41:5: runtime error: store to misaligned address 0x555559745d9c for type 'unsigned long', which requires 8 byte alignment
0x555559745d9c: note: pointer points here
ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
^
#0 0x555556fb81c4 in set_bit /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/qemu/bitops.h:41:9
#1 0x555556fb81c4 in extioi_setirq /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/clang/../../hw/intc/loongarch_extioi.c:65:9
#2 0x555556fb6e90 in pch_pic_irq_handler /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/clang/../../hw/intc/loongarch_pch_pic.c:75:5
#3 0x555556710265 in serial_ioport_write /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/clang/../../hw/char/serial.c
Fix these problems by using set_bit32() and clear_bit32(),
which work with bit arrays stored as an array of uint32_t.
Cc: qemu-stable@nongnu.org
Fixes: cbff2db1e9 ("hw/intc: Add LoongArch extioi interrupt controller(EIOINTC)")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-id: 20241108135514.4006953-4-peter.maydell@linaro.org
(cherry picked from commit 335be5bc44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: drop hunk in hw/intc/loongarch_extioi.c:extioi_update_sw_coremap()
due to missing v8.2.0-548-g428a6ef4396a "hw/intc/loongarch_extioi: Add vmstate post_load support")
Currently bitops.h defines a set of operations that work on
arbitrary-length bit arrays. However (largely because they
originally came from the Linux kernel) the bit array storage is an
array of 'unsigned long'. This is OK for the kernel and even for
parts of QEMU where we don't really care about the underlying storage
format, but it is not good for devices, where we often want to expose
the storage to the guest and so need a type that is not
variably-sized between host OSes.
We already have a workaround for this in the GICv3 model:
arm_gicv3_common.h defines equivalents of the bit operations that
work on uint32_t. It turns out that we should also be using
something similar in hw/intc/loongarch_extioi.c, which currently
casts a pointer to a uint32_t array to 'unsigned long *' in
extio_setirq(), which is both undefined behaviour and not correct on
a big-endian host.
Define equivalents of the set_bit() function family which work
with a uint32_t array.
(Cc stable because we're about to provide a bugfix to
loongarch_extioi which will depend on this commit.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241108135514.4006953-2-peter.maydell@linaro.org
(cherry picked from commit 3d7680fb18)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The clang sanitizer complains about the code in the EOI handling
of openpic_cpu_write_internal():
UBSAN_OPTIONS=halt_on_error=1:abort_on_error=1 ./build/clang/qemu-system-ppc -M mac99,graphics=off -display none -kernel day15/invaders.elf
../../hw/intc/openpic.c:1034:16: runtime error: index -1 out of bounds for type 'IRQSource[264]' (aka 'struct IRQSource[264]')
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior ../../hw/intc/openpic.c:1034:16 in
This is because we do
src = &opp->src[n_IRQ];
when n_IRQ may be -1. This is in practice harmless because if n_IRQ
is -1 then we don't do anything with the src pointer, but it is
undefined behaviour. (This has been present since this device
was first added to QEMU.)
Rearrange the code so we only do the array index when n_IRQ is not -1.
Cc: qemu-stable@nongnu.org
Fixes: e9df014c0b ("Implement embedded IRQ controller for PowerPC 6xx/740 & 75")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20241105180205.3074071-1-peter.maydell@linaro.org
(cherry picked from commit 3bf7dcd47a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ClearPortFeature control message fails for PORT_POWER because there
is no break; at the end of the case statement, causing it to fall through
to the failure handler. Add the missing break; to solve the problem.
Fixes: 1cc403eb21 ("usb-hub: emulate per port power switching")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241112170152.217664-11-linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit b2cc699979)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When SET_STREAM_FORMAT is called, the st->buft timer is overwritten, thus
causing a memory leak. This was originally fixed in commit 816139ae6a5
("hw/audio/hda: fix memory leak on audio setup", 2024-11-14) but that
caused the audio to break in SPICE.
Fortunately, a simpler fix is possible. The timer only needs to be
reset, because the callback is always the same (st->output is set at
realize time in hda_audio_init); call to timer_new_ns overkill. Replace
it with timer_del and only initialize the timer once; for simplicity,
do it even if use_timer is false.
An even simpler fix would be to free the old time in hda_audio_setup().
However, it seems better to place the initialization of the timer close
to that of st->ouput.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20241114125318.1707590-3-pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 626b39006d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When compiling QEMU with --enable-cfi, the "q800" m68k machine
currently crashes very early, when the q800_machine_init() function
tries to wire the interrupts of the "via1" device.
This happens because TYPE_MOS6522_Q800_VIA1 is supposed to be a
proper SysBus device, but its parent (TYPE_MOS6522) has a mistake
in its class definition where it is only derived from DeviceClass,
and not from SysBusDeviceClass, so we end up in funny memory access
issues here. Using the right class hierarchy for the MOS6522 device
fixes the problem.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2675
Signed-off-by: Thomas Huth <thuth@redhat.com>
Fixes: 51f233ec92 ("misc: introduce new mos6522 VIA device")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20241114104653.963812-1-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit c3d7c18b0d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In simd_desc() we create a SIMD descriptor from various pieces
including an arbitrary data value from the caller. We try to
sanitize these to make sure everything will fit: the 'data' value
needs to fit in the SIMD_DATA_BITS (== 22) sized field. However we
do that sanitizing with:
tcg_debug_assert(data == sextract32(data, 0, SIMD_DATA_BITS));
This works for the case where the data is supposed to be considered
as a signed integer (which can then be returned via simd_data()).
However, some callers want to treat the data value as unsigned.
Specifically, for the Arm SVE operations, make_svemte_desc()
assembles a data value as a collection of fields, and it needs to use
all 22 bits. Currently if MTE is enabled then its MTEDESC SIZEM1
field may have the most significant bit set, and then it will trip
this assertion.
Loosen the assertion so that we only check that the data value will
fit into the field in some way, either as a signed or as an unsigned
value. This means we will fail to detect some kinds of bug in the
callers, but we won't spuriously assert for intentional use of the
data field as unsigned.
Cc: qemu-stable@nongnu.org
Fixes: db432672dc ("tcg: Add generic vector expanders")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2601
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20241115172515.1229393-1-peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 8377e3fb85)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The commit fd6f7798ac ("linux-user: Use direct syscalls for setuid(),
etc") added direct syscall wrappers for setuid(), setgid(), etc since the
system calls have different semantics than the libc functions.
Add and use the corresponding wrappers for setreuid and setregid which
were missed in that commit.
This fixes the build of the debian package of the uid_wrapper library
(https://cwrap.org/uid_wrapper.html) when running linux-user.
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <Zyo2jMKqq8hG8Pkz@p100>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 8491026a08)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit b56617bbcb ("target/i386: Walk NPT in guest real mode") added
logic to run the page table walker even in real mode if we are in NPT
mode. That function then determined whether real mode or paging is
active based on whether the pg_mode variable was 0.
Unfortunately pg_mode is 0 in two situations:
1) Paging is disabled (real mode)
2) Paging is in 2-level paging mode (32bit without PAE)
That means the walker now assumed that 2-level paging mode was real
mode, breaking NetBSD as well as Windows XP.
To fix that, this patch adds a new PG flag to pg_mode which indicates
whether paging is active at all and uses that to determine whether we
are in real mode or not.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2654
Fixes: b56617bbcb ("target/i386: Walk NPT in guest real mode")
Fixes: 253c0a06e0 (commit b56617bbcb in stable-7.2.x series)
Signed-off-by: Alexander Graf <graf@amazon.com>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Link: https://lore.kernel.org/r/20241106154329.67218-1-graf@amazon.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 8fa11a4df3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A bad (broken or malicious) 9p client (guest) could cause QEMU host to
crash by sending a 9p 'Treaddir' request with a numeric file ID (FID) that
was previously opened for a file instead of an expected directory:
#0 0x0000762aff8f4919 in __GI___rewinddir (dirp=0xf) at
../sysdeps/unix/sysv/linux/rewinddir.c:29
#1 0x0000557b7625fb40 in do_readdir_many (pdu=0x557bb67d2eb0,
fidp=0x557bb67955b0, entries=0x762afe9fff58, offset=0, maxsize=131072,
dostat=<optimized out>) at ../hw/9pfs/codir.c:101
#2 v9fs_co_readdir_many (pdu=pdu@entry=0x557bb67d2eb0,
fidp=fidp@entry=0x557bb67955b0, entries=entries@entry=0x762afe9fff58,
offset=0, maxsize=131072, dostat=false) at ../hw/9pfs/codir.c:226
#3 0x0000557b7625c1f9 in v9fs_do_readdir (pdu=0x557bb67d2eb0,
fidp=0x557bb67955b0, offset=<optimized out>,
max_count=<optimized out>) at ../hw/9pfs/9p.c:2488
#4 v9fs_readdir (opaque=0x557bb67d2eb0) at ../hw/9pfs/9p.c:2602
That's because V9fsFidOpenState was declared as union type. So the
same memory region is used for either an open POSIX file handle (int),
or a POSIX DIR* pointer, etc., so 9p server incorrectly used the
previously opened (valid) POSIX file handle (0xf) as DIR* pointer,
eventually causing a crash in glibc's rewinddir() function.
Root cause was therefore a missing check in 9p server's 'Treaddir'
request handler, which must ensure that the client supplied FID was
really opened as directory stream before trying to access the
aforementioned union and its DIR* member.
Cc: qemu-stable@nongnu.org
Fixes: d62dbb51f7 ("virtio-9p: Add fidtype so that we can do type ...")
Reported-by: Akihiro Suda <suda.kyoto@gmail.com>
Tested-by: Akihiro Suda <suda.kyoto@gmail.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <E1t8GnN-002RS8-E2@kylie.crudebyte.com>
(cherry picked from commit 042b4ebfd2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If a host chooses to use the SQHD "hint" in the CQE to know if there is
room in the submission queue for additional commands, it may result in a
situation where there are not enough internal resources (struct
NvmeRequest) available to process the command. For a lack of a better
term, the host may "over-commit" the device (i.e., it may have more
inflight commands than the queue size).
For example, assume a queue with N entries. The host submits N commands
and all are picked up for processing, advancing the head and emptying
the queue. Regardless of which of these N commands complete first, the
SQHD field of that CQE will indicate to the host that the queue is
empty, which allows the host to issue N commands again. However, if the
device has not posted CQEs for all the previous commands yet, the device
will have less than N resources available to process the commands, so
queue processing is suspended.
And here lies an 11 year latent bug. In the absense of any additional
tail updates on the submission queue, we never schedule the processing
bottom-half again unless we observe a head update on an associated full
completion queue. This has been sufficient to handle N-to-1 SQ/CQ setups
(in the absense of over-commit of course). Incidentially, that "kick all
associated SQs" mechanism can now be killed since we now just schedule
queue processing when we return a processing resource to a non-empty
submission queue, which happens to cover both edge cases. However, we
must retain kicking the CQ if it was previously full.
So, apparently, no previous driver tested with hw/nvme has ever used
SQHD (e.g., neither the Linux NVMe driver or SPDK uses it). But then OSv
shows up with the driver that actually does. I salute you.
Fixes: f3c507adcd ("NVMe: Initial commit for new storage interface")
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2388
Reported-by: Waldemar Kozaczuk <jwkozaczuk@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit 9529aa6bb4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Our implementation of the indexed version of SVE SDOT/UDOT/USDOT got
the calculation of the inner loop terminator wrong. Although we
correctly account for the element size when we calculate the
terminator for the first iteration:
intptr_t segend = MIN(16 / sizeof(TYPED), opr_sz_n);
we don't do that when we move it forward after the first inner loop
completes. The intention is that we process the vector in 128-bit
segments, which for a 64-bit element size should mean (1, 2), (3, 4),
(5, 6), etc. This bug meant that we would iterate (1, 2), (3, 4, 5,
6), (7, 8, 9, 10) etc and apply the wrong indexed element to some of
the operations, and also index off the end of the vector.
You don't see this bug if the vector length is small enough that we
don't need to iterate the outer loop, i.e. if it is only 128 bits,
or if it is the 64-bit special case from AA32/AA64 AdvSIMD. If the
vector length is 256 bits then we calculate the right results for the
elements in the vector but do index off the end of the vector. Vector
lengths greater than 256 bits see wrong answers. The instructions
that produce 32-bit results behave correctly.
Fix the recalculation of 'segend' for subsequent iterations, and
restore a version of the comment that was lost in the refactor of
commit 7020ffd656 that explains why we only need to clamp segend to
opr_sz_n for the first iteration, not the later ones.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2595
Fixes: 7020ffd656 ("target/arm: Macroize helper_gvec_{s,u}dot_idx_{b,h}")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241101185544.2130972-1-peter.maydell@linaro.org
(cherry picked from commit e6b2fa1b81)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
divdu (without a dot) sometimes updates cr0, even though it shouldn't.
The reason is that gen_op_arith_divd() checks Rc(ctx->opcode), which is
not initialized. This field is initialized only for instructions that
go through decode_legacy(), and not decodetree.
There already was a similar issue fixed in commit 86e6202a57
("target/ppc: Make divw[u] handler method decodetree compatible.").
It's not immediately clear what else may access the uninitialized
ctx->opcode, so instead of playing whack-a-mole and changing the check
to compute_rc0, simply initialize ctx->opcode.
Cc: qemu-stable@nongnu.org
Fixes: 99082815f1 ("target/ppc: Add infrastructure for prefixed insns")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit c9b8a13a88)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The section 4.5.2 of the RISC-V AIA specification says that any write
to a sourcecfg register of an APLIC might (or might not) cause the
corresponding interrupt-pending bit to be set to one if the rectified
input value is high (= 1) under the new source mode.
If an interrupt is asserted before the driver configs its interrupt
type to APLIC, it's pending bit will not be set except a relevant
write to a setip or setipnum register. When we write the interrupt
type to sourcecfg register, if the APLIC device doesn't check
rectified input value and update the pending bit, this interrupt
might never becomes pending.
For APLIC.m, we can manully set pending by setip or setipnum
registers in driver. But for APLIC.w, the pending status totally
depends on the rectified input value, we can't control the pending
status via mmio registers. In this case, hw should check and update
pending status for us when writing sourcecfg registers.
Update QEMU emulation to handle "pre-existing" interrupts.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241004104649.13129-1-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 2ae6cca1d3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in hw/intc/riscv_aplic.c)
The reads to in_clrip[x] registers return rectified input values of the
interrupt sources.
A rectified input value of an interrupt source is defined by the section
"4.5.2 Source configurations (sourcecfg[1]–sourcecfg[1023])" of the RISC-V
AIA specification as:
"rectified input value = (incoming wire value) XOR (source is inverted)"
Update the riscv_aplic_read_input_word() implementation to match the above.
Fixes: e8f79343cf ("hw/intc: Add RISC-V AIA APLIC device emulation")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240306095722.463296-3-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 0678e9f29c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The RISC-V unprivileged specification "31.3.11. State of Vector
Extension at Reset" has a note that recommends vtype.vill be set on
reset as part of ensuring that the vector extension have a consistent
state at reset.
This change now makes QEMU consistent with Spike which sets vtype.vill
on reset.
Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240930165258.72258-1-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit f8c1f36a2e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The register VXSAT should be RW only to the first bit.
The remaining bits should be 0.
The RISC-V Instruction Set Manual Volume I: Unprivileged Architecture
The vxsat CSR has a single read-write least-significant bit (vxsat[0])
that indicates if a fixed-point instruction has had to saturate an output
value to fit into a destination format. Bits vxsat[XLEN-1:1]
should be written as zeros.
Signed-off-by: Evgenii Prokopiev <evgenii.prokopiev@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241002084436.89347-1-evgenii.prokopiev@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 5a60026cad)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In regime_is_user() we assert if we're passed an ARMMMUIdx_E10_*
mmuidx value. This used to make sense because we only used this
function in ptw.c and would never use it on this kind of stage 1+2
mmuidx, only for an individual stage 1 or stage 2 mmuidx.
However, when we implemented FEAT_E0PD we added a callsite in
aa64_va_parameters(), which means this can now be called for
stage 1+2 mmuidx values if the guest sets the TCG_ELX.{E0PD0,E0PD1}
bits to enable use of the feature. This will then result in
an assertion failure later, for instance on a TLBI operation:
#6 0x00007ffff6d0e70f in g_assertion_message_expr
(domain=0x0, file=0x55555676eeba "../../target/arm/internals.h", line=978, func=0x555556771d48 <__func__.5> "regime_is_user", expr=<optimised out>)
at ../../../glib/gtestutils.c:3279
#7 0x0000555555f286d2 in regime_is_user (env=0x555557f2fe00, mmu_idx=ARMMMUIdx_E10_0) at ../../target/arm/internals.h:978
#8 0x0000555555f3e31c in aa64_va_parameters (env=0x555557f2fe00, va=18446744073709551615, mmu_idx=ARMMMUIdx_E10_0, data=true, el1_is_aa32=false)
at ../../target/arm/helper.c:12048
#9 0x0000555555f3163b in tlbi_aa64_get_range (env=0x555557f2fe00, mmuidx=ARMMMUIdx_E10_0, value=106721347371041) at ../../target/arm/helper.c:5214
#10 0x0000555555f317e8 in do_rvae_write (env=0x555557f2fe00, value=106721347371041, idxmap=21, synced=true) at ../../target/arm/helper.c:5260
#11 0x0000555555f31925 in tlbi_aa64_rvae1is_write (env=0x555557f2fe00, ri=0x555557fbeae0, value=106721347371041) at ../../target/arm/helper.c:5302
#12 0x0000555556036f8f in helper_set_cp_reg64 (env=0x555557f2fe00, rip=0x555557fbeae0, value=106721347371041) at ../../target/arm/tcg/op_helper.c:965
Since we do know whether these mmuidx values are for usermode
or not, we can easily make regime_is_user() handle them:
ARMMMUIdx_E10_0 is user, and the other two are not.
Cc: qemu-stable@nongnu.org
Fixes: e4c93e44ab ("target/arm: Implement FEAT_E0PD")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20241017172331.822587-1-peter.maydell@linaro.org
(cherry picked from commit 1505b651fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The patch fixes the following errors generated by GCC 14.2:
../src/net/tap-win32.c:343:19: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 176 [-Werror=format-truncation=]
343 | "%s\\%s\\Connection",
| ^~
344 | NETWORK_CONNECTIONS_KEY, enum_name);
| ~~~~~~~~~
../src/net/tap-win32.c:341:9: note: 'snprintf' output between 92 and 347 bytes into a destination of size 256
341 | snprintf(connection_string,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
342 | sizeof(connection_string),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
343 | "%s\\%s\\Connection",
| ~~~~~~~~~~~~~~~~~~~~~
344 | NETWORK_CONNECTIONS_KEY, enum_name);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../src/net/tap-win32.c:242:58: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 178 [-Werror=format-truncation=]
242 | snprintf (unit_string, sizeof(unit_string), "%s\\%s",
| ^~
243 | ADAPTER_KEY, enum_name);
| ~~~~~~~~~
../src/net/tap-win32.c:242:9: note: 'snprintf' output between 79 and 334 bytes into a destination of size 256
242 | snprintf (unit_string, sizeof(unit_string), "%s\\%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
243 | ADAPTER_KEY, enum_name);
| ~~~~~~~~~~~~~~~~~~~~~~~
../src/net/tap-win32.c:620:52: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 245 [-Werror=format-truncation=]
620 | snprintf (device_path, sizeof(device_path), "%s%s%s",
| ^~
621 | USERMODEDEVICEDIR,
622 | device_guid,
| ~~~~~~~~~~~
../src/net/tap-win32.c:620:5: note: 'snprintf' output between 16 and 271 bytes into a destination of size 256
620 | snprintf (device_path, sizeof(device_path), "%s%s%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
621 | USERMODEDEVICEDIR,
| ~~~~~~~~~~~~~~~~~~
622 | device_guid,
| ~~~~~~~~~~~~
623 | TAPSUFFIX);
| ~~~~~~~~~~
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2607
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 75fe36b4e8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When translating virtual to physical address with a guest CPU that
supports nested paging (NPT), we need to perform every page table walk
access indirectly through the NPT, which we correctly do.
However, we treat real mode (no page table walk) special: In that case,
we currently just skip any walks and translate VA -> PA. With NPT
enabled, we also need to then perform NPT walk to do GVA -> GPA -> HPA
which we fail to do so far.
The net result of that is that TCG VMs with NPT enabled that execute
real mode code (like SeaBIOS) end up with GPA==HPA mappings which means
the guest accesses host code and data. This typically shows as failure
to boot guests.
This patch changes the page walk logic for NPT enabled guests so that we
always perform a GVA -> GPA translation and then skip any logic that
requires an actual PTE.
That way, all remaining logic to walk the NPT stays and we successfully
walk the NPT in real mode.
Cc: qemu-stable@nongnu.org
Fixes: fe441054bb ("target-i386: Add NPT support")
Signed-off-by: Alexander Graf <graf@amazon.com>
Reported-by: Eduard Vlad <evlad@amazon.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240921085712.28902-1-graf@amazon.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit b56617bbcb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Coverity complains (CID 1507880) that the declaration "int error_code;"
in mmu_translate() is unreachable code. Since this is only a declaration,
this isn't actually a bug, but:
* it's a bear-trap for future changes, because if it was changed to
include an initialization 'int error_code = foo;' then the
initialization wouldn't actually happen (being dead code)
* it's against our coding style, which wants declarations to be
at the start of blocks
* it means that anybody reading the code has to go and look up
exactly what the C rules are for skipping over variable declarations
using a goto
Move the declaration to the top of the function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230406155946.3362077-1-peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 987b63f24a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: cherry-pick this for stable-7.2 so that the next patch applies cleanly)
s->offset and s->size are only set at the end of the function and still
contain the old values when formatting the error message. Print the
parameters with the new values that we actually checked instead.
Fixes: 500e243420 ('raw-format: Split raw_read_options()')
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240829185527.47152-1-kwolf@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 04bbc3ee52)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Rather than waiting for the completion of migration on the source side,
wait for it on the destination QEMU side to avoid accessing the TPM TIS
memory mapped registers before QEMU could restore their state. This
error condition could be triggered on busy systems where the destination
QEMU did not have enough time to restore the TIS state while the test case
was already reading its registers. The test case was for example reading
the STS register and received an unexpected value (0xffffffff), which
lead to a segmentation fault later on due to trying to read 0xffff bytes
from the TIS into a buffer.
Cc: <qemu-stable@nongnu.org>
Reported-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
(cherry picked from commit d9280ea317)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Zhiyi reported an infinite loop issue in VFIO use case. The cause of that
was a separate discussion, however during that I found a regression of
dirty sync slowness when profiling.
Each KVMMemoryListerner maintains an array of kvm memslots. Currently it's
statically allocated to be the max supported by the kernel. However after
Linux commit 4fc096a99e ("KVM: Raise the maximum number of user memslots"),
the max supported memslots reported now grows to some number large enough
so that it may not be wise to always statically allocate with the max
reported.
What's worse, QEMU kvm code still walks all the allocated memslots entries
to do any form of lookups. It can drastically slow down all memslot
operations because each of such loop can run over 32K times on the new
kernels.
Fix this issue by making the memslots to be allocated dynamically.
Here the initial size was set to 16 because it should cover the basic VM
usages, so that the hope is the majority VM use case may not even need to
grow at all (e.g. if one starts a VM with ./qemu-system-x86_64 by default
it'll consume 9 memslots), however not too large to waste memory.
There can also be even better way to address this, but so far this is the
simplest and should be already better even than before we grow the max
supported memslots. For example, in the case of above issue when VFIO was
attached on a 32GB system, there are only ~10 memslots used. So it could
be good enough as of now.
In the above VFIO context, measurement shows that the precopy dirty sync
shrinked from ~86ms to ~3ms after this patch applied. It should also apply
to any KVM enabled VM even without VFIO.
NOTE: we don't have a FIXES tag for this patch because there's no real
commit that regressed this in QEMU. Such behavior existed for a long time,
but only start to be a problem when the kernel reports very large
nr_slots_max value. However that's pretty common now (the kernel change
was merged in 2021) so we attached cc:stable because we'll want this change
to be backported to stable branches.
Cc: qemu-stable <qemu-stable@nongnu.org>
Reported-by: Zhiyi Guo <zhguo@redhat.com>
Tested-by: Zhiyi Guo <zhguo@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20240917163835.194664-2-peterx@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 5504a81261)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in accel/kvm/kvm-all.c and accel/kvm/trace-events;
also remove now-unused local variable `KVMState *s` in kvm-all.c:kvm_log_sync_global() )
The result of 1 << regbit with regbit==31 has a 1 in the 32nd bit.
When cast to uint64_t (for further bitwise OR), the 32 most
significant bits will be filled with 1s. However, the documentation
states that the upper 32 bits of ICH_AP[0/1]R<n>_EL2 are reserved.
Add an explicit cast to match the documentation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: c3f21b065a ("hw/intc/arm_gicv3_cpuif: Support vLPIs")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 3db74afec3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs") split
calls to scsi_req_new() and scsi_req_enqueue() in the virtio-scsi device.
No ill effects were observed until commit 8cc5583abe ("virtio-scsi: Send
"REPORTED LUNS CHANGED" sense data upon disk hotplug events") added a
unit attention that was easy to trigger with device hotplug and
hot-unplug.
Because the two calls were separated, all requests in the batch were
prepared calling scsi_req_new() to report a sense. The first one
submitted would report the right sense and reset it to NO_SENSE, while
the others reported CHECK_CONDITION with no sense data. This caused
SCSI errors in Linux.
To solve this issue, let's fetch the unit attention as early as possible
when we prepare the request, so that only the first request in the batch
will use the unit attention SCSIReqOps and the others will not report
CHECK CONDITION.
Fixes: 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs")
Fixes: 8cc5583abe ("virtio-scsi: Send "REPORTED LUNS CHANGED" sense data upon disk hotplug events")
Reported-by: Thomas Huth <thuth@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2176702
Co-developed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 9472083e64)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Comparing a string of 4 bytes only works in little-endian.
Adjust bulk bswap to only apply to the note payload.
Perform swapping of the note header manually; the magic
is defined so that it does not need a runtime swap.
Fixes: 83f990eb5a ("linux-user/elfload: Parse NT_GNU_PROPERTY_TYPE_0 notes")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2596
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 2884596f5f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we are building for OSS-Fuzz, we want to ensure that the fuzzer
targets are actually created, regardless of leaks. Leaks will be
detected by the subsequent tests of the individual fuzz-targets.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240527150001.325565-1-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 3e964275d6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Allow overlapping request by removing the assert that made it
impossible. There are only two callers:
1. block_copy_task_create()
It already asserts the very same condition before calling
reqlist_init_req().
2. cbw_snapshot_read_lock()
There is no need to have read requests be non-overlapping in
copy-before-write when used for snapshot-access. In fact, there was no
protection against two callers of cbw_snapshot_read_lock() calling
reqlist_init_req() with overlapping ranges and this could lead to an
assertion failure [1].
In particular, with the reproducer script below [0], two
cbw_co_snapshot_block_status() callers could race, with the second
calling reqlist_init_req() before the first one finishes and removes
its conflicting request.
[0]:
> #!/bin/bash -e
> dd if=/dev/urandom of=/tmp/disk.raw bs=1M count=1024
> ./qemu-img create /tmp/fleecing.raw -f raw 1G
> (
> ./qemu-system-x86_64 --qmp stdio \
> --blockdev raw,node-name=node0,file.driver=file,file.filename=/tmp/disk.raw \
> --blockdev raw,node-name=node1,file.driver=file,file.filename=/tmp/fleecing.raw \
> <<EOF
> {"execute": "qmp_capabilities"}
> {"execute": "blockdev-add", "arguments": { "driver": "copy-before-write", "file": "node0", "target": "node1", "node-name": "node3" } }
> {"execute": "blockdev-add", "arguments": { "driver": "snapshot-access", "file": "node3", "node-name": "snap0" } }
> {"execute": "nbd-server-start", "arguments": {"addr": { "type": "unix", "data": { "path": "/tmp/nbd.socket" } } } }
> {"execute": "block-export-add", "arguments": {"id": "exp0", "node-name": "snap0", "type": "nbd", "name": "exp0"}}
> EOF
> ) &
> sleep 5
> while true; do
> ./qemu-nbd -d /dev/nbd0
> ./qemu-nbd -c /dev/nbd0 nbd:unix:/tmp/nbd.socket:exportname=exp0 -f raw -r
> nbdinfo --map 'nbd+unix:///exp0?socket=/tmp/nbd.socket'
> done
[1]:
> #5 0x000071e5f0088eb2 in __GI___assert_fail (...) at ./assert/assert.c:101
> #6 0x0000615285438017 in reqlist_init_req (...) at ../block/reqlist.c:23
> #7 0x00006152853e2d98 in cbw_snapshot_read_lock (...) at ../block/copy-before-write.c:237
> #8 0x00006152853e3068 in cbw_co_snapshot_block_status (...) at ../block/copy-before-write.c:304
> #9 0x00006152853f4d22 in bdrv_co_snapshot_block_status (...) at ../block/io.c:3726
> #10 0x000061528543a63e in snapshot_access_co_block_status (...) at ../block/snapshot-access.c:48
> #11 0x00006152853f1a0a in bdrv_co_do_block_status (...) at ../block/io.c:2474
> #12 0x00006152853f2016 in bdrv_co_common_block_status_above (...) at ../block/io.c:2652
> #13 0x00006152853f22cf in bdrv_co_block_status_above (...) at ../block/io.c:2732
> #14 0x00006152853d9a86 in blk_co_block_status_above (...) at ../block/block-backend.c:1473
> #15 0x000061528538da6c in blockstatus_to_extents (...) at ../nbd/server.c:2374
> #16 0x000061528538deb1 in nbd_co_send_block_status (...) at ../nbd/server.c:2481
> #17 0x000061528538f424 in nbd_handle_request (...) at ../nbd/server.c:2978
> #18 0x000061528538f906 in nbd_trip (...) at ../nbd/server.c:3121
> #19 0x00006152855a7caf in coroutine_trampoline (...) at ../util/coroutine-ucontext.c:175
Cc: qemu-stable@nongnu.org
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240712140716.517911-1-f.ebner@proxmox.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
(cherry picked from commit 6475155d51)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The XT check for the lxvx/stxvx instructions is currently
inverted. This was introduced during the move to decodetree.
>From the ISA:
Chapter 7. Vector-Scalar Extension Facility
Load VSX Vector Indexed X-form
lxvx XT,RA,RB
if TX=0 & MSR.VSX=0 then VSX_Unavailable()
if TX=1 & MSR.VEC=0 then Vector_Unavailable()
...
Let XT be the value 32×TX + T.
The code currently does the opposite:
if (paired || a->rt >= 32) {
REQUIRE_VSX(ctx);
} else {
REQUIRE_VECTOR(ctx);
}
This was already fixed for lxv/stxv at commit "2cc0e449d1 (target/ppc:
Fix lxv/stxv MSR facility check)", but the indexed forms were missed.
Cc: qemu-stable@nongnu.org
Fixes: 70426b5bb7 ("target/ppc: moved stxvx and lxvx from legacy to decodtree")
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-ID: <20240911141651.6914-1-farosas@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 8bded2e73e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The follow-up transactions may use the data in the attribution, so keep
the value of attribution from the function parameter just as
flatview_translate() above.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Cc: qemu-stable@nongnu.org
Fixes: f26404fbee ("Make address_space_map() take a MemTxAttrs argument")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/r/20240912070404.2993976-2-fea.wang@sifive.com
Signed-off-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit d8d5ca4004)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix due to lack of
v9.1.0-134-g637b0aa13956 "softmmu: Support concurrent bounce buffers"
v9.0.0-564-g69e78f1b3484 "system/physmem: Per-AddressSpace bounce buffering")
On GICv2 and later, level triggered interrupts are pending when either
the interrupt line is asserted or the interrupt was made pending by a
GICD_ISPENDRn write. Making a level triggered interrupt pending by
software persists until either the interrupt is acknowledged or cleared
by writing GICD_ICPENDRn. As long as the interrupt line is asserted,
the interrupt is pending in any case.
This logic is transparently implemented in gic_test_pending() for
GICv1 and GICv2. The function combines the "pending" irq_state flag
(used for edge triggered interrupts and software requests) and the
line status (tracked in the "level" field). However, we also
incorrectly set the pending flag on a guest write to GICD_ISENABLERn
if the line of a level triggered interrupt was asserted. This keeps
the interrupt pending even if the line is de-asserted after some
time.
This incorrect logic is a leftover of the initial 11MPCore GIC
implementation. That handles things slightly differently to the
architected GICv1 and GICv2. The 11MPCore TRM does not give a lot of
detail on the corner cases of its GIC's behaviour, and historically
we have not wanted to investigate exactly what it does in reality, so
QEMU's GIC model takes the approach of "retain our existing behaviour
for 11MPCore, and implement the architectural standard for later GIC
revisions".
On that basis, commit 8d999995e4 in 2013 is where we added the
"level-triggered interrupt with the line asserted" handling to
gic_test_pending(), and we deliberately kept the old behaviour of
gic_test_pending() for REV_11MPCORE. That commit should have added
the "only if 11MPCore" condition to the setting of the pending bit on
writes to GICD_ISENABLERn, but forgot it.
Add the missing "if REV_11MPCORE" condition, so that our behaviour
on GICv1 and GICv2 matches the GIC architecture requirements.
Cc: qemu-stable@nongnu.org
Fixes: 8d999995e4 ("arm_gic: Fix GIC pending behavior")
Signed-off-by: Jan Klötzke <jan.kloetzke@kernkonzept.com>
Message-id: 20240911114826.3558302-1-jan.kloetzke@kernkonzept.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: expanded comment a little and converted to coding-style form;
expanded commit message with the historical backstory]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 110684c9a6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
As debian-11 transitions to LTS we are starting to have problems
building the image. While we could update to a later Debian building a
32 bit QEMU without modern floating point is niche host amongst the
few remaining 32 bit hosts we regularly build for. For now we still
have armhf-debian-cross-container which is currently built from the
more recent debian-12.
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240910173900.4154726-2-alex.bennee@linaro.org>
(cherry picked from commit d0068b746a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: force-delete tests/docker/dockerfiles/debian-armel-cross.docker,
fixups in .gitlab-ci.d/crossbuilds.yml,
context fixup in tests/lcitool/refresh)
Both gnutls and gcrypt can be configured to exclude support for certain
algorithms via a runtime check against system crypto policies. Thus it
is not sufficient to have a compile time test for hash support in their
pbkdf implementations.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
(cherry picked from commit e6c09ea4f9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
As reported by Peter, we might be leaking memory when removing the
highest RAMBlock (in the weird ram_addr_t space), and adding a new one.
We will fail to realize that we already allocated bitmaps for more
dirty memory blocks, and effectively discard the pointers to them.
Fix it by getting rid of last_ram_page() and by remembering the number
of dirty memory blocks that have been allocated already.
While at it, let's use "unsigned int" for the number of blocks, which
should be sufficient until we reach ~32 exabytes.
Looks like this leak was introduced as we switched from using a single
bitmap_zero_extend() to allocating multiple bitmaps:
bitmap_zero_extend() relies on g_renew() which should have taken care of
this.
Resolves: https://lkml.kernel.org/r/CAFEAcA-k7a+VObGAfCFNygQNfCKL=AfX6A4kScq=VSSK0peqPg@mail.gmail.com
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 5b82b703b6 ("memory: RCU ram_list.dirty_memory[] for safe RAM hotplug")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20240828090743.128647-1-david@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit b84f06c2be)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix due to lack of
v9.0.0-rc4-49-g15f7a80c49cb "RAMBlock: Add support of KVM private guest memfd")
When the creds->username property is set we allocate memory
for it in qcrypto_tls_creds_psk_prop_set_username(), but
we never free this when the QCryptoTLSCredsPSK is destroyed.
Free the memory in finalize.
This fixes a LeakSanitizer complaint in migration-test:
$ (cd build/asan; ASAN_OPTIONS="fast_unwind_on_malloc=0" QTEST_QEMU_BINARY=./qemu-system-x86_64 ./tests/qtest/migration-test --tap -k -p /x86_64/migration/precopy/unix/tls/psk)
=================================================================
==3867512==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 5 byte(s) in 1 object(s) allocated from:
#0 0x5624e5c99dee in malloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-x86_64+0x218edee) (BuildId: a9e623fa1009a9435c0142c037cd7b8c1ad04ce3)
#1 0x7fb199ae9738 in g_malloc debian/build/deb/../../../glib/gmem.c:128:13
#2 0x7fb199afe583 in g_strdup debian/build/deb/../../../glib/gstrfuncs.c:361:17
#3 0x5624e82ea919 in qcrypto_tls_creds_psk_prop_set_username /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../crypto/tlscredspsk.c:255:23
#4 0x5624e812c6b5 in property_set_str /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/object.c:2277:5
#5 0x5624e8125ce5 in object_property_set /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/object.c:1463:5
#6 0x5624e8136e7c in object_set_properties_from_qdict /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/object_interfaces.c:55:14
#7 0x5624e81372d2 in user_creatable_add_type /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/object_interfaces.c:112:5
#8 0x5624e8137964 in user_creatable_add_qapi /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/object_interfaces.c:157:11
#9 0x5624e891ba3c in qmp_object_add /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qom/qom-qmp-cmds.c:227:5
#10 0x5624e8af9118 in qmp_marshal_object_add /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qapi/qapi-commands-qom.c:337:5
#11 0x5624e8bd1d49 in do_qmp_dispatch_bh /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../qapi/qmp-dispatch.c:128:5
#12 0x5624e8cb2531 in aio_bh_call /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/async.c:171:5
#13 0x5624e8cb340c in aio_bh_poll /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/async.c:218:13
#14 0x5624e8c0be98 in aio_dispatch /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/aio-posix.c:423:5
#15 0x5624e8cba3ce in aio_ctx_dispatch /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/async.c:360:5
#16 0x7fb199ae0d3a in g_main_dispatch debian/build/deb/../../../glib/gmain.c:3419:28
#17 0x7fb199ae0d3a in g_main_context_dispatch debian/build/deb/../../../glib/gmain.c:4137:7
#18 0x5624e8cbe1d9 in glib_pollfds_poll /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/main-loop.c:287:9
#19 0x5624e8cbcb13 in os_host_main_loop_wait /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/main-loop.c:310:5
#20 0x5624e8cbc6dc in main_loop_wait /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../util/main-loop.c:589:11
#21 0x5624e6f3f917 in qemu_main_loop /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../system/runstate.c:801:9
#22 0x5624e893379c in qemu_default_main /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../system/main.c:37:14
#23 0x5624e89337e7 in main /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/../../system/main.c:48:12
#24 0x7fb197972d8f in __libc_start_call_main csu/../sysdeps/nptl/libc_start_call_main.h:58:16
#25 0x7fb197972e3f in __libc_start_main csu/../csu/libc-start.c:392:3
#26 0x5624e5c16fa4 in _start (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-x86_64+0x210bfa4) (BuildId: a9e623fa1009a9435c0142c037cd7b8c1ad04ce3)
SUMMARY: AddressSanitizer: 5 byte(s) leaked in 1 allocation(s).
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240819145021.38524-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 87e012f29f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 3e7ef738 plugged the use-after-free of the global nbd_server
object, but overlooked a use-after-free of nbd_server->listener.
Although this race is harder to hit, notice that our shutdown path
first drops the reference count of nbd_server->listener, then triggers
actions that can result in a pending client reaching the
nbd_blockdev_client_closed() callback, which in turn calls
qio_net_listener_set_client_func on a potentially stale object.
If we know we don't want any more clients to connect, and have already
told the listener socket to shut down, then we should not be trying to
update the listener socket's associated function.
Reproducer:
> #!/usr/bin/python3
>
> import os
> from threading import Thread
>
> def start_stop():
> while 1:
> os.system('virsh qemu-monitor-command VM \'{"execute": "nbd-server-start",
+"arguments":{"addr":{"type":"unix","data":{"path":"/tmp/nbd-sock"}}}}\'')
> os.system('virsh qemu-monitor-command VM \'{"execute": "nbd-server-stop"}\'')
>
> def nbd_list():
> while 1:
> os.system('/path/to/build/qemu-nbd -L -k /tmp/nbd-sock')
>
> def test():
> sst = Thread(target=start_stop)
> sst.start()
> nlt = Thread(target=nbd_list)
> nlt.start()
>
> sst.join()
> nlt.join()
>
> test()
Fixes: CVE-2024-7409
Fixes: 3e7ef738c8 ("nbd/server: CVE-2024-7409: Close stray clients at server-stop")
CC: qemu-stable@nongnu.org
Reported-by: Andrey Drobyshev <andrey.drobyshev@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240822143617.800419-2-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 3874f5f73c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A malicious client can attempt to connect to an NBD server, and then
intentionally delay progress in the handshake, including if it does
not know the TLS secrets. Although the previous two patches reduce
this behavior by capping the default max-connections parameter and
killing slow clients, they did not eliminate the possibility of a
client waiting to close the socket until after the QMP nbd-server-stop
command is executed, at which point qemu would SEGV when trying to
dereference the NULL nbd_server global which is no longer present.
This amounts to a denial of service attack. Worse, if another NBD
server is started before the malicious client disconnects, I cannot
rule out additional adverse effects when the old client interferes
with the connection count of the new server (although the most likely
is a crash due to an assertion failure when checking
nbd_server->connections > 0).
For environments without this patch, the CVE can be mitigated by
ensuring (such as via a firewall) that only trusted clients can
connect to an NBD server. Note that using frameworks like libvirt
that ensure that TLS is used and that nbd-server-stop is not executed
while any trusted clients are still connected will only help if there
is also no possibility for an untrusted client to open a connection
but then stall on the NBD handshake.
Given the previous patches, it would be possible to guarantee that no
clients remain connected by having nbd-server-stop sleep for longer
than the default handshake deadline before finally freeing the global
nbd_server object, but that could make QMP non-responsive for a long
time. So intead, this patch fixes the problem by tracking all client
sockets opened while the server is running, and forcefully closing any
such sockets remaining without a completed handshake at the time of
nbd-server-stop, then waiting until the coroutines servicing those
sockets notice the state change. nbd-server-stop now has a second
AIO_WAIT_WHILE_UNLOCKED (the first is indirectly through the
blk_exp_close_all_type() that disconnects all clients that completed
handshakes), but forced socket shutdown is enough to progress the
coroutines and quickly tear down all clients before the server is
freed, thus finally fixing the CVE.
This patch relies heavily on the fact that nbd/server.c guarantees
that it only calls nbd_blockdev_client_closed() from the main loop
(see the assertion in nbd_client_put() and the hoops used in
nbd_client_put_nonzero() to achieve that); if we did not have that
guarantee, we would also need a mutex protecting our accesses of the
list of connections to survive re-entrancy from independent iothreads.
Although I did not actually try to test old builds, it looks like this
problem has existed since at least commit 862172f45c (v2.12.0, 2017) -
even back when that patch started using a QIONetListener to handle
listening on multiple sockets, nbd_server_free() was already unaware
that the nbd_blockdev_client_closed callback can be reached later by a
client thread that has not completed handshakes (and therefore the
client's socket never got added to the list closed in
nbd_export_close_all), despite that patch intentionally tearing down
the QIONetListener to prevent new clients.
Reported-by: Alexander Ivanov <alexander.ivanov@virtuozzo.com>
Fixes: CVE-2024-7409
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240807174943.771624-14-eblake@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
(cherry picked from commit 3e7ef738c8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A client that opens a socket but does not negotiate is merely hogging
qemu's resources (an open fd and a small amount of memory); and a
malicious client that can access the port where NBD is listening can
attempt a denial of service attack by intentionally opening and
abandoning lots of unfinished connections. The previous patch put a
default bound on the number of such ongoing connections, but once that
limit is hit, no more clients can connect (including legitimate ones).
The solution is to insist that clients complete handshake within a
reasonable time limit, defaulting to 10 seconds. A client that has
not successfully completed NBD_OPT_GO by then (including the case of
where the client didn't know TLS credentials to even reach the point
of NBD_OPT_GO) is wasting our time and does not deserve to stay
connected. Later patches will allow fine-tuning the limit away from
the default value (including disabling it for doing integration
testing of the handshake process itself).
Note that this patch in isolation actually makes it more likely to see
qemu SEGV after nbd-server-stop, as any client socket still connected
when the server shuts down will now be closed after 10 seconds rather
than at the client's whims. That will be addressed in the next patch.
For a demo of this patch in action:
$ qemu-nbd -f raw -r -t -e 10 file &
$ nbdsh --opt-mode -c '
H = list()
for i in range(20):
print(i)
H.insert(i, nbd.NBD())
H[i].set_opt_mode(True)
H[i].connect_uri("nbd://localhost")
'
$ kill $!
where later connections get to start progressing once earlier ones are
forcefully dropped for taking too long, rather than hanging.
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240807174943.771624-13-eblake@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[eblake: rebase to changes earlier in series, reduce scope of timer]
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit b9b72cb3ce)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in nbd/server.c: lack of WITH_QEMU_LOCK_GUARD in 7.2)
Allowing an unlimited number of clients to any web service is a recipe
for a rudimentary denial of service attack: the client merely needs to
open lots of sockets without closing them, until qemu no longer has
any more fds available to allocate.
For qemu-nbd, we default to allowing only 1 connection unless more are
explicitly asked for (-e or --shared); this was historically picked as
a nice default (without an explicit -t, a non-persistent qemu-nbd goes
away after a client disconnects, without needing any additional
follow-up commands), and we are not going to change that interface now
(besides, someday we want to point people towards qemu-storage-daemon
instead of qemu-nbd).
But for qemu proper, and the newer qemu-storage-daemon, the QMP
nbd-server-start command has historically had a default of unlimited
number of connections, in part because unlike qemu-nbd it is
inherently persistent until nbd-server-stop. Allowing multiple client
sockets is particularly useful for clients that can take advantage of
MULTI_CONN (creating parallel sockets to increase throughput),
although known clients that do so (such as libnbd's nbdcopy) typically
use only 8 or 16 connections (the benefits of scaling diminish once
more sockets are competing for kernel attention). Picking a number
large enough for typical use cases, but not unlimited, makes it
slightly harder for a malicious client to perform a denial of service
merely by opening lots of connections withot progressing through the
handshake.
This change does not eliminate CVE-2024-7409 on its own, but reduces
the chance for fd exhaustion or unlimited memory usage as an attack
surface. On the other hand, by itself, it makes it more obvious that
with a finite limit, we have the problem of an unauthenticated client
holding 100 fds opened as a way to block out a legitimate client from
being able to connect; thus, later patches will further add timeouts
to reject clients that are not making progress.
This is an INTENTIONAL change in behavior, and will break any client
of nbd-server-start that was not passing an explicit max-connections
parameter, yet expects more than 100 simultaneous connections. We are
not aware of any such client (as stated above, most clients aware of
MULTI_CONN get by just fine on 8 or 16 connections, and probably cope
with later connections failing by relying on the earlier connections;
libvirt has not yet been passing max-connections, but generally
creates NBD servers with the intent for a single client for the sake
of live storage migration; meanwhile, the KubeSAN project anticipates
a large cluster sharing multiple clients [up to 8 per node, and up to
100 nodes in a cluster], but it currently uses qemu-nbd with an
explicit --shared=0 rather than qemu-storage-daemon with
nbd-server-start).
We considered using a deprecation period (declare that omitting
max-parameters is deprecated, and make it mandatory in 3 releases -
then we don't need to pick an arbitrary default); that has zero risk
of breaking any apps that accidentally depended on more than 100
connections, and where such breakage might not be noticed under unit
testing but only under the larger loads of production usage. But it
does not close the denial-of-service hole until far into the future,
and requires all apps to change to add the parameter even if 100 was
good enough. It also has a drawback that any app (like libvirt) that
is accidentally relying on an unlimited default should seriously
consider their own CVE now, at which point they are going to change to
pass explicit max-connections sooner than waiting for 3 qemu releases.
Finally, if our changed default breaks an app, that app can always
pass in an explicit max-parameters with a larger value.
It is also intentional that the HMP interface to nbd-server-start is
not changed to expose max-connections (any client needing to fine-tune
things should be using QMP).
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240807174943.771624-12-eblake@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[ericb: Expand commit message to summarize Dan's argument for why we
break corner-case back-compat behavior without a deprecation period]
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit c8a76dbd90)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: minor fixups in qapi/block-export.json)
Upcoming patches to fix a CVE need to track an opaque pointer passed
in by the owner of a client object, as well as request for a time
limit on how fast negotiation must complete. Prepare for that by
changing the signature of nbd_client_new() and adding an accessor to
get at the opaque pointer, although for now the two servers
(qemu-nbd.c and blockdev-nbd.c) do not change behavior even though
they pass in a new default timeout value.
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240807174943.771624-11-eblake@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[eblake: s/LIMIT/MAX_SECS/ as suggested by Dan]
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit fb1c2aaa98)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When reading with `read_cluster` we get the `mapping` with
`find_mapping_for_cluster` and then we call `open_file` for this
mapping.
The issue appear when its the same file, but a second cluster that is
not immediately after it, imagine clusters `500 -> 503`, this will give
us 2 mappings one has the range `500..501` and another `503..504`, both
point to the same file, but different offsets.
When we don't open the file since the path is the same, we won't assign
`s->current_mapping` and thus accessing way out of bound of the file.
From our example above, after `open_file` (that didn't open anything) we
will get the offset into the file with
`s->cluster_size*(cluster_num-s->current_mapping->begin)`, which will
give us `0x2000 * (504-500)`, which is out of bound for this mapping and
will produce some issues.
Signed-off-by: Amjad Alsharafi <amjadsharafi10@gmail.com>
Message-ID: <1f3ea115779abab62ba32c788073cdc99f9ad5dd.1721470238.git.amjadsharafi10@gmail.com>
[kwolf: Simplified the patch based on Amjad's analysis and input]
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 5eed3db336)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
How this `abort` was intended to check for was:
- if the `mapping->first_mapping_index` is not the same as
`first_mapping_index`, which **should** happen only in one case,
when we are handling the first mapping, in that case
`mapping->first_mapping_index == -1`, in all other cases, the other
mappings after the first should have the condition `true`.
- From above, we know that this is the first mapping, so if the offset
is not `0`, then abort, since this is an invalid state.
The issue was that `first_mapping_index` is not set if we are
checking from the middle, the variable `first_mapping_index` is
only set if we passed through the check `cluster_was_modified` with the
first mapping, and in the same function call we checked the other
mappings.
One approach is to go into the loop even if `cluster_was_modified`
is not true so that we will be able to set `first_mapping_index` for the
first mapping, but since `first_mapping_index` is only used here,
another approach is to just check manually for the
`mapping->first_mapping_index != -1` since we know that this is the
value for the only entry where `offset == 0` (i.e. first mapping).
Signed-off-by: Amjad Alsharafi <amjadsharafi10@gmail.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <b0fbca3ee208c565885838f6a7deeaeb23f4f9c2.1721470238.git.amjadsharafi10@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit f60a6f7e17)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Before this commit, the behavior when calling `commit_one_file` for
example with `offset=0x2000` (second cluster), what will happen is that
we won't fetch the next cluster from the fat, and instead use the first
cluster for the read operation.
This is due to off-by-one error here, where `i=0x2000 !< offset=0x2000`,
thus not fetching the next cluster.
Signed-off-by: Amjad Alsharafi <amjadsharafi10@gmail.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <b97c1e1f1bc2f776061ae914f95d799d124fcd73.1721470238.git.amjadsharafi10@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit b881cf00c9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Patch 06b1297017 ("virtio-net: fix network stall under load")
added double-check to test whether the available buffer size
can satisfy the request or not, in case the guest has added
some buffers to the avail ring simultaneously after the first
check. It will be lucky if the available buffer size becomes
okay after the double-check, then the host can send the packet
to the guest. If the buffer size still can't satisfy the request,
even if the guest has added some buffers, viritio-net would
stall at the host side forever.
The patch enables notification and checks whether the guest has
added some buffers since last check of available buffers when
the available buffers are insufficient. If no buffer is added,
return false, else recheck the available buffers in the loop.
If the available buffers are sufficient, disable notification
and return true.
Changes:
1. Change the return type of virtqueue_get_avail_bytes() from void
to int, it returns an opaque that represents the shadow_avail_idx
of the virtqueue on success, else -1 on error.
2. Add a new API: virtio_queue_enable_notification_and_check(),
it takes an opaque as input arg which is returned from
virtqueue_get_avail_bytes(). It enables notification firstly,
then checks whether the guest has added some buffers since
last check of available buffers or not by virtio_queue_poll(),
return ture if yes.
The patch also reverts patch "06b12970174".
The case below can reproduce the stall.
Guest 0
+--------+
| iperf |
---------------> | server |
Host | +--------+
+--------+ | ...
| iperf |----
| client |---- Guest n
+--------+ | +--------+
| | iperf |
---------------> | server |
+--------+
Boot many guests from qemu with virtio network:
qemu ... -netdev tap,id=net_x \
-device virtio-net-pci-non-transitional,\
iommu_platform=on,mac=xx:xx:xx:xx:xx:xx,netdev=net_x
Each guest acts as iperf server with commands below:
iperf3 -s -D -i 10 -p 8001
iperf3 -s -D -i 10 -p 8002
The host as iperf client:
iperf3 -c guest_IP -p 8001 -i 30 -w 256k -P 20 -t 40000
iperf3 -c guest_IP -p 8002 -i 30 -w 256k -P 20 -t 40000
After some time, the host loses connection to the guest,
the guest can send packet to the host, but can't receive
packet from the host.
It's more likely to happen if SWIOTLB is enabled in the guest,
allocating and freeing bounce buffer takes some CPU ticks,
copying from/to bounce buffer takes more CPU ticks, compared
with that there is no bounce buffer in the guest.
Once the rate of producing packets from the host approximates
the rate of receiveing packets in the guest, the guest would
loop in NAPI.
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
| need kick the host?
| NAPI continues
v
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
v
... ...
On the other hand, the host fetches free buf from avail
ring, if the buf in the avail ring is not enough, the
host notifies the guest the event by writing the avail
idx read from avail ring to the event idx of used ring,
then the host goes to sleep, waiting for the kick signal
from the guest.
Once the guest finds the host is waiting for kick singal
(in virtqueue_kick_prepare_split()), it kicks the host.
The host may stall forever at the sequences below:
Host Guest
------------ -----------
fetch buf, send packet receive packet ---
... ... |
fetch buf, send packet add buf |
... add buf virtnet_poll
buf not enough avail idx-> add buf |
read avail idx add buf |
add buf ---
receive packet ---
write event idx ... |
wait for kick add buf virtnet_poll
... |
---
no more packet, exit NAPI
In the first loop of NAPI above, indicated in the range of
virtnet_poll above, the host is sending packets while the
guest is receiving packets and adding buffers.
step 1: The buf is not enough, for example, a big packet
needs 5 buf, but the available buf count is 3.
The host read current avail idx.
step 2: The guest adds some buf, then checks whether the
host is waiting for kick signal, not at this time.
The used ring is not empty, the guest continues
the second loop of NAPI.
step 3: The host writes the avail idx read from avail
ring to used ring as event idx via
virtio_queue_set_notification(q->rx_vq, 1).
step 4: At the end of the second loop of NAPI, recheck
whether kick is needed, as the event idx in the
used ring written by the host is beyound the
range of kick condition, the guest will not
send kick signal to the host.
Fixes: 06b1297017 ("virtio-net: fix network stall under load")
Cc: qemu-stable@nongnu.org
Signed-off-by: Wencheng Yang <east.moutain.yang@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit f937309fbd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in include/hw/virtio/virtio.h)
Ensure the queue index points to a valid queue when software RSS
enabled. The new calculation matches with the behavior of Linux's TAP
device with the RSS eBPF program.
Fixes: 4474e37a5b ("virtio-net: implement RX RSS processing")
Reported-by: Zhibin Hu <huzhibin5@huawei.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit f1595ceb9a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixes: CVE-2024-6505
The FMOPA (widening) SME instruction takes pairs of half-precision
floating point values, widens them to single-precision, does a
two-way dot product and accumulates the results into a
single-precision destination. We don't quite correctly handle the
FPCR bits FZ and FZ16 which control flushing of denormal inputs and
outputs. This is because at the moment we pass a single float_status
value to the helper function, which then uses that configuration for
all the fp operations it does. However, because the inputs to this
operation are float16 and the outputs are float32 we need to use the
fp_status_f16 for the float16 input widening but the normal fp_status
for everything else. Otherwise we will apply the flushing control
FPCR.FZ16 to the 32-bit output rather than the FPCR.FZ control, and
incorrectly flush a denormal output to zero when we should not (or
vice-versa).
(In commit 207d30b5fd we tried to fix the FZ handling but
didn't get it right, switching from "use FPCR.FZ for everything" to
"use FPCR.FZ16 for everything".)
(Mjt: it is commit d5373d7bdb in stable-7.2)
Pass the CPU env to the sme_fmopa_h helper instead of an fp_status
pointer, and have the helper pass an extra fp_status into the
f16_dotadd() function so that we can use the right status for the
right parts of this operation.
Cc: qemu-stable@nongnu.org
Fixes: 207d30b5fd ("target/arm: Use FPST_F16 for SME FMOPA (widening)")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2373
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 55f9f4ee01)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: s/tcg_env/cpu_env/ due to missingv
8.1.0-1189-gad75a51e84af "tcg: Rename cpu_env to tcg_env")
In newer versions of Sphinx the env.doc2path() API is going to change
to return a Path object rather than a str. This was originally visible
in Sphinx 8.0.0rc1, but has been rolled back for the final 8.0.0
release. However it will probably emit a deprecation warning and is
likely to change for good in 9.0:
https://github.com/sphinx-doc/sphinx/issues/12686
Our use in depfile.py assumes a str, and if it is passed a Path
it will fall over:
Handler <function write_depfile at 0x77a1775ff560> for event 'build-finished' threw an exception (exception: unsupported operand type(s) for +: 'PosixPath' and 'str')
Wrapping the env.doc2path() call in str() will coerce a Path object
to the str we expect, and have no effect in older Sphinx versions
that do return a str.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2458
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240729120533.2486427-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 48e5b5f994)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When determining the current vector length, the SMCR_EL2.LEN and
SVCR_EL2.LEN settings should only be considered if EL2 is enabled
(compare the pseudocode CurrentSVL and CurrentNSVL which call
EL2Enabled()).
We were checking against ARM_FEATURE_EL2 rather than calling
arm_is_el2_enabled(), which meant that we would look at
SMCR_EL2/SVCR_EL2 when in Secure EL1 or Secure EL0 even if Secure EL2
was not enabled.
Use the correct check in sve_vqm1_for_el_sm().
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240722172957.1041231-5-peter.maydell@linaro.org
(cherry picked from commit f573ac059e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The function tszimm_esz() returns a shift amount, or possibly -1 in
certain cases that correspond to unallocated encodings in the
instruction set. We catch these later in the trans_ functions
(generally with an "a-esz < 0" check), but before we do the
decodetree-generated code will also call tszimm_shr() or tszimm_sl(),
which will use the tszimm_esz() return value as a shift count without
checking that it is not negative, which is undefined behaviour.
Avoid the UB by checking the return value in tszimm_shr() and
tszimm_shl().
Cc: qemu-stable@nongnu.org
Resolves: Coverity CID 1547617, 1547694
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240722172957.1041231-4-peter.maydell@linaro.org
(cherry picked from commit 76916dfa89)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The UMOPA/UMOPS instructions are supposed to multiply unsigned 8 or
16 bit elements and accumulate the products into a 64-bit element.
In the Arm ARM pseudocode, this is done with the usual
infinite-precision signed arithmetic. However our implementation
doesn't quite get it right, because in the DEF_IMOP_64() macro we do:
sum += (NTYPE)(n >> 0) * (MTYPE)(m >> 0);
where NTYPE and MTYPE are uint16_t or int16_t. In the uint16_t case,
the C usual arithmetic conversions mean the values are converted to
"int" type and the multiply is done as a 32-bit multiply. This means
that if the inputs are, for example, 0xffff and 0xffff then the
result is 0xFFFE0001 as an int, which is then promoted to uint64_t
for the accumulation into sum; this promotion incorrectly sign
extends the multiply.
Avoid the incorrect sign extension by casting to int64_t before
the multiply, so we do the multiply as 64-bit signed arithmetic,
which is a type large enough that the multiply can never
overflow into the sign bit.
(The equivalent 8-bit operations in DEF_IMOP_32() are fine, because
the 8-bit multiplies can never overflow into the sign bit of a
32-bit integer.)
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2372
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240722172957.1041231-3-peter.maydell@linaro.org
(cherry picked from commit ea3f5a90f0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For an instruction which accesses a 128-bit element tile when
the SVL is also 128 (for example MOV z0.Q, p0/M, ZA0H.Q[w0,0]),
we will assert in get_tile_rowcol():
qemu-system-aarch64: ../../tcg/tcg-op.c:926: tcg_gen_deposit_z_i32: Assertion `len > 0' failed.
This happens because we calculate
len = ctz32(streaming_vec_reg_size(s)) - esz;$
but if the SVL and the element size are the same len is 0, and
the deposit operation asserts.
In this case the ZA storage contains exactly one 128 bit
element ZA tile, and the horizontal or vertical slice is just
that tile. This means that regardless of the index value in
the Ws register, we always access that tile. (In pseudocode terms,
we calculate (index + offset) MOD 1, which is 0.)
Special case the len == 0 case to avoid hitting the assertion
in tcg_gen_deposit_z_i32().
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240722172957.1041231-2-peter.maydell@linaro.org
(cherry picked from commit 56f1c0db92)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The documentation of the "Set palette" mailbox property at
https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface#set-palette
says it has the form:
Length: 24..1032
Value:
u32: offset: first palette index to set (0-255)
u32: length: number of palette entries to set (1-256)
u32...: RGBA palette values (offset to offset+length-1)
We get this wrong in a couple of ways:
* we aren't checking the offset and length are in range, so the guest
can make us spin for a long time by providing a large length
* the bounds check on our loop is wrong: we should iterate through
'length' palette entries, not 'length - offset' entries
Fix the loop to implement the bounds checks and get the loop
condition right. In the process, make the variables local to
this switch case, rather than function-global, so it's clearer
what type they are when reading the code.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723131029.1159908-2-peter.maydell@linaro.org
(cherry picked from commit 0892fffc2a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix due to lack of
v9.0.0-1812-g5d5f1b60916a "hw/misc: Implement mailbox properties for customer OTP and device specific private keys"
v8.0.0-1924-g251918266666 "hw/misc/bcm2835_property: Use 'raspberrypi-fw-defs.h' definitions"
also remove now-unused local `n' variable which gets removed in the next change in this file,
v9.0.0-2720-g32f1c201eedf "hw/misc/bcm2835_property: Avoid overflow in OTP access properties")
When a bare-metal application on the raspi3 board reads the
AUX_MU_STAT_REG MMIO register while the device's buffer is
at full receive FIFO capacity
(i.e. `s->read_count == BCM2835_AUX_RX_FIFO_LEN`) the
assertion `assert(s->read_count < BCM2835_AUX_RX_FIFO_LEN)`
fails.
Reported-by: Cryptjar <cryptjar@junk.studio>
Suggested-by: Cryptjar <cryptjar@junk.studio>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/459
Signed-off-by: Frederik van Hövell <frederik@fvhovell.nl>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMM: commit message tweaks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 546d574b11)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The unrealize functions of the various vhost-user devices are
calling the corresponding vhost_*_set_status() functions with a
status of 0 to shut down the device correctly.
Now these vhost_*_set_status() functions all follow this scheme:
bool should_start = virtio_device_should_start(vdev, status);
if (vhost_dev_is_started(&vvc->vhost_dev) == should_start) {
return;
}
if (should_start) {
/* ... do the initialization stuff ... */
} else {
/* ... do the cleanup stuff ... */
}
The problem here is virtio_device_should_start(vdev, 0) currently
always returns "true" since it internally only looks at vdev->started
instead of looking at the "status" parameter. Thus once the device
got started once, virtio_device_should_start() always returns true
and thus the vhost_*_set_status() functions return early, without
ever doing any clean-up when being called with status == 0. This
causes e.g. problems when trying to hot-plug and hot-unplug a vhost
user devices multiple times since the de-initialization step is
completely skipped during the unplug operation.
This bug has been introduced in commit 9f6bcfd99f ("hw/virtio: move
vm_running check to virtio_device_started") which replaced
should_start = status & VIRTIO_CONFIG_S_DRIVER_OK;
with
should_start = virtio_device_started(vdev, status);
which later got replaced by virtio_device_should_start(). This blocked
the possibility to set should_start to false in case the status flag
VIRTIO_CONFIG_S_DRIVER_OK was not set.
Fix it by adjusting the virtio_device_should_start() function to
only consider the status flag instead of vdev->started. Since this
function is only used in the various vhost_*_set_status() functions
for exactly the same purpose, it should be fine to fix it in this
central place there without any risk to change the behavior of other
code.
Fixes: 9f6bcfd99f ("hw/virtio: move vm_running check to virtio_device_started")
Buglink: https://issues.redhat.com/browse/RHEL-40708
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240618121958.88673-1-thuth@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit d72479b117)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
aio_context_set_thread_pool_params() takes two int64_t arguments to
set the minimum and maximum number of threads in the pool. We do
some bounds checking on these, but we don't catch the case where the
inputs are negative. This means that later in the function when we
assign these inputs to the AioContext::thread_pool_min and
::thread_pool_max fields, which are of type int, the values might
overflow the smaller type.
A negative number of threads is meaningless, so make
aio_context_set_thread_pool_params() return an error if either min or
max are negative.
Resolves: Coverity CID 1547605
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723150927.1396456-1-peter.maydell@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 851495571d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Loongson IPI is only available in little-endian,
so use that to access the guest memory (in case
we run on a big-endian host).
Cc: qemu-stable@nongnu.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Fixes: f6783e3438 ("hw/loongarch: Add LoongArch ipi interrupt support")
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240718133312.10324-3-philmd@linaro.org>
(cherry picked from commit 2465c89fb9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixups for 7.2, for lack of:
v9.0.0-583-g91d0b151de4c "hw/intc/loongson_ipi: Implement IOCSR address space for MIPS"
v9.0.0-582-gb4a12dfc2132 "hw/intc/loongarch_ipi: Rename as loongson_ipi"
v8.2.0-545-gfdd6ee0b7653 "hw/intc/loongarch_ipi: Use MemTxAttrs interface for ipi ops")
If I use `-serial stdio` on Windows, after QEMU exits, the terminal
could not handle arrow keys and tab any more. Because stdio backend
on Windows sets console mode to virtual terminal input when starts,
but does not restore the old mode when finalize.
This small patch saves the old console mode and set it back.
Signed-off-by: Ziming Song <s.ziming@hotmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <ME3P282MB25488BE7C39BF0C35CD0DA5D8CA82@ME3P282MB2548.AUSP282.PROD.OUTLOOK.COM>
(cherry picked from commit 903cc9e117)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
sgx_epc_get_section assumes a PC platform is in use:
bool sgx_epc_get_section(int section_nr, uint64_t *addr, uint64_t *size)
{
PCMachineState *pcms = PC_MACHINE(qdev_get_machine());
However, sgx_epc_get_section is called by CPUID regardless of whether
SGX state has been initialized or which platform is in use. Check
whether the machine has the right QOM class and if not behave as if
there are no EPC sections.
Fixes: 1dec2e1f19 ("i386: Update SGX CPUID info according to hardware/KVM/user input", 2021-09-30)
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2142
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 13be929aff)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The allocated memory to hold LBA ranges leaks in the nvme_dsm function. This
happens because the allocated memory for iocb->range is not freed in all
error handling paths.
Fix this by adding a free to ensure that the allocated memory is properly freed.
ASAN log:
==3075137==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 480 byte(s) in 6 object(s) allocated from:
#0 0x55f1f8a0eddd in malloc llvm/compiler-rt/lib/asan/asan_malloc_linux.cpp:129:3
#1 0x7f531e0f6738 in g_malloc (/lib/x86_64-linux-gnu/libglib-2.0.so.0+0x5e738)
#2 0x55f1faf1f091 in blk_aio_get block/block-backend.c:2583:12
#3 0x55f1f945c74b in nvme_dsm hw/nvme/ctrl.c:2609:30
#4 0x55f1f945831b in nvme_io_cmd hw/nvme/ctrl.c:4470:16
#5 0x55f1f94561b7 in nvme_process_sq hw/nvme/ctrl.c:7039:29
Cc: qemu-stable@nongnu.org
Fixes: d7d1474fd8 ("hw/nvme: reimplement dsm to allow cancellation")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit c510fe78f1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When handling image filenames from legacy options such as -drive or from
tools, these filenames are parsed for protocol prefixes, including for
the json:{} pseudo-protocol.
This behaviour is intended for filenames that come directly from the
command line and for backing files, which may come from the image file
itself. Higher level management tools generally take care to verify that
untrusted images don't contain a bad (or any) backing file reference;
'qemu-img info' is a suitable tool for this.
However, for other files that can be referenced in images, such as
qcow2 data files or VMDK extents, the string from the image file is
usually not verified by management tools - and 'qemu-img info' wouldn't
be suitable because in contrast to backing files, it already opens these
other referenced files. So here the string should be interpreted as a
literal local filename. More complex configurations need to be specified
explicitly on the command line or in QMP.
This patch changes bdrv_open_inherit() so that it only parses filenames
if a new parameter parse_filename is true. It is set for the top level
in bdrv_open(), for the file child and for the backing file child. All
other callers pass false and disable filename parsing this way.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
(cherry picked from commit 7ead946998)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: backport patch to 7.2, without:
v8.0.0-2069-g8394c35ee148 "block: Fix AioContext locking in bdrv_open_child()"
v8.1.0-801-gafdaeb9ea06e "block: Mark bdrv_attach_child() GRAPH_WRLOCK"
v8.2.0-rc0-59-g6bc0bcc89f84 "block: Fix deadlocks in bdrv_graph_wrunlock()"
v8.2.0-132-g6bc30f194985 "graph-lock: remove AioContext locking"
v8.2.0-133-gb49f4755c7fa "block: remove AioContext locking")
We want to disable filename parsing for data files because it's too easy
to abuse in malicious image files. Make the test ready for the change by
passing the data file explicitly in command line options.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
(cherry picked from commit 7e1110664e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We want to disable filename parsing for data files because it's too easy
to abuse in malicious image files. Make the test ready for the change by
passing the data file explicitly in command line options.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
(cherry picked from commit 2eb42a728d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
One use case for 'qemu-img info' is verifying that untrusted images
don't reference an unwanted external file, be it as a backing file or an
external data file. To make sure that calling 'qemu-img info' can't
already have undesired side effects with a malicious image, just don't
open the data file at all with BDRV_O_NO_IO. If nothing ever tries to do
I/O, we don't need to have it open.
This changes the output of iotests case 061, which used 'qemu-img info'
to show that opening an image with an invalid data file fails. After
this patch, it succeeds. Replace this part of the test with a qemu-io
call, but keep the final 'qemu-img info' to show that the invalid data
file is correctly displayed in the output.
Fixes: CVE-2024-4467
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
(cherry picked from commit bd385a5298)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When QEMU is started with:
-cpu host,host-cache-info=on,l3-cache=off \
-smp 2,sockets=1,dies=1,cores=1,threads=2
Guest can't acquire maximum number of addressable IDs for processor cores in
the physical package from CPUID[04H].
When creating a CPU topology of 1 core per package, host-cache-info only
uses the Host's addressable core IDs field (CPUID.04H.EAX[bits 31-26]),
resulting in a conflict (on the multicore Host) between the Guest core
topology information in this field and the Guest's actual cores number.
Fix it by removing the unnecessary condition to cover 1 core per package
case. This is safe because cores_per_pkg will not be 0 and will be at
least 1.
Fixes: d7caf13b5f ("x86: cpu: fixup number of addressable IDs for logical processors sharing cache")
Signed-off-by: Guixiong Wei <weiguixiong@bytedance.com>
Signed-off-by: Yipeng Yin <yinyipeng@bytedance.com>
Signed-off-by: Chuang Xu <xuchuangxclwt@bytedance.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240611032314.64076-1-xuchuangxclwt@bytedance.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 903916f0a0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup for 7.2 due to other changes in this area past 8.2)
RHEL 9 (and thus also the derivatives) have been available since two
years now, so according to QEMU's support policy, we can drop the active
support for the previous major version 8 now.
Another reason for doing this is that Centos Stream 8 will go EOL soon:
https://blog.centos.org/2023/04/end-dates-are-coming-for-centos-stream-8-and-centos-linux-7/
"After May 31, 2024, CentOS Stream 8 will be archived
and no further updates will be provided."
Thus upgrade our CentOS Stream container to major version 9 now.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240418101056.302103-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 641b1efe01)
(Mjt: numerous merge conflicts due to many changes in testing framework)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Python 3.6 is at end-of-life. Update the libvirt-ci module to a
version that supports overrides for targets and package mappings;
this way, QEMU can use the newer versions provided by CentOS 8 (Python
3.8) and OpenSUSE 15.3 (Python 3.9).
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit d639cf79783a1eba349b7705e0fb270fa76118a4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Let's safe some CI minutes by merging these two jobs. We can now
also drop "--disable-capstone" since the capstone submodule has
been removed a while ago. We should rather test --disable-fdt now
to check a compilation without the "dtc" submodule (for this we
have to drop i386-softmmu from the target list unfortunately).
Additionally, the qtests with s390x and sh4 are not read for
"--without-default-devices" yet, so we can only test mips64 and
avr here now.
Message-Id: <20230130104446.1286773-5-thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e030d08c2f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Simplify the logic for two-part, 32-bit pc-relative addresses.
Rather than assume all such fit in int32_t, do some arithmetic
and assert a result, do some arithmetic first and then check
to see if the pieces are in range.
Cc: qemu-stable@nongnu.org
Fixes: dacc51720d ("tcg/loongarch64: Implement tcg_out_mov and tcg_out_movi")
Reviewed-by: Song Gao <gaosong@loongson.cn>
Reported-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 521d7fb3eb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in tcg/loongarch64/tcg-target.c.inc)
Reproducer from https://gitlab.com/qemu-project/qemu/-/issues/1451
creates small packet (1 segment, len = 10 == n->guest_hdr_len),
then destroys queue.
"if (n->host_hdr_len != n->guest_hdr_len)" is triggered, if body creates
zero length/zero segment packet as there is nothing after guest header.
qemu_sendv_packet_async() tries to send it.
slirp discards it because it is smaller than Ethernet header,
but returns 0 because tx hooks are supposed to return total length of data.
0 is propagated upwards and is interpreted as "packet has been sent"
which is terrible because queue is being destroyed, nobody is waiting for TX
to complete and assert it triggered.
Fix is discard such empty packets instead of sending them.
Length 1 packets will go via different codepath:
virtqueue_push(q->tx_vq, elem, 0);
virtio_notify(vdev, q->tx_vq);
g_free(elem);
and aren't problematic.
Signed-off-by: Alexey Dobriyan <adobriyan@yandex-team.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 2c3e4e2de6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The calculation of FrameTemp is done using the size indicated by mo_pushpop()
before being written back to EBP, but the final writeback to EBP is done using
the size indicated by mo_stacksize().
In the case where mo_pushpop() is MO_32 and mo_stacksize() is MO_16 then the
final writeback to EBP is done using MO_16 which can leave junk in the top
16-bits of EBP after executing ENTER.
Change the writeback of EBP to use the same size indicated by mo_pushpop() to
ensure that the full value is written back.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2198
Message-ID: <20240606095319.229650-5-mark.cave-ayland@ilande.co.uk>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 3973615e7f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
By default, SDL disables the screen saver which prevents the host from powering
down the screen even if the screen is locked. This results in draining the
battery needlessly when the host isn't connected to a wall charger. Fix that by
enabling the screen saver.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20240512095945.1879-1-shentey@gmail.com>
(cherry picked from commit 2e701e6785)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
xsave.flat checks that "executing the XSETBV instruction causes a general-
protection fault (#GP) if ECX = 0 and EAX[2:1] has the value 10b". QEMU allows
that option, so the test fails. Add the condition.
Cc: qemu-stable@nongnu.org
Fixes: 892544317f ("target/i386: implement XSAVE and XRSTOR of AVX registers", 2022-10-18)
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 7604bbc2d8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In gic_cpu_read() and gic_cpu_write(), we delegate the handling of
reading and writing the Non-Secure view of the GICC_APR<n> registers
to functions gic_apr_ns_view() and gic_apr_write_ns_view().
Unfortunately we got the order of the arguments wrong, swapping the
CPU number and the register number (which the compiler doesn't catch
because they're both integers).
Most guests probably didn't notice this bug because directly
accessing the APR registers is typically something only done by
firmware when it is doing state save for going into a sleep mode.
Correct the mismatched call arguments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: 51fd06e0ee ("hw/intc/arm_gic: Fix handling of GICC_APR<n>, GICC_NSAPR<n> registers")
Signed-off-by: Andrey Shumilin <shum.sdl@nppct.ru>
[PMM: Rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée<alex.bennee@linaro.org>
(cherry picked from commit daafa78b29)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We wrongly encoded ID_AA64PFR1_EL1 using {3,0,0,4,2} in hvf_sreg_match[] so
we fail to get the expected ARMCPRegInfo from cp_regs hash table with the
wrong key.
Fix it with the correct encoding {3,0,0,4,1}. With that fixed, the Linux
guest can properly detect FEAT_SSBS2 on my M1 HW.
All DBG{B,W}{V,C}R_EL1 registers are also wrongly encoded with op0 == 14.
It happens to work because HVF_SYSREG(CRn, CRm, 14, op1, op2) equals to
HVF_SYSREG(CRn, CRm, 2, op1, op2), by definition. But we shouldn't rely on
it.
Cc: qemu-stable@nongnu.org
Fixes: a1477da3dd ("hvf: Add Apple Silicon support")
Signed-off-by: Zenghui Yu <zenghui.yu@linux.dev>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20240503153453.54389-1-zenghui.yu@linux.dev
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 19ed42e8ad)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Intel SDM 18.3.1.4 "If an occurrence of the MOV or POP instruction
loads the SS register executes with EFLAGS.TF = 1, no single-step debug
exception occurs following the MOV or POP instruction."
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit f0f0136abb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup for v8.1.0-1189-gad75a51e84af "tcg: Rename cpu_env to tcg_env")
This bug fix addresses the incorrect return value of kvm_hv_handle_exit for
KVM_EXIT_HYPERV_SYNIC, which should be EXCP_INTERRUPT.
Handling of KVM_EXIT_HYPERV_SYNIC in QEMU needs to be synchronous.
This means that async_synic_update should run in the current QEMU vCPU
thread before returning to KVM, returning EXCP_INTERRUPT to guarantee this.
Returning 0 can cause async_synic_update to run asynchronously.
One problem (kvm-unit-tests's hyperv_synic test fails with timeout error)
caused by this bug:
When a guest VM writes to the HV_X64_MSR_SCONTROL MSR to enable Hyper-V SynIC,
a VM exit is triggered and processed by the kvm_hv_handle_exit function of the
QEMU vCPU. This function then calls the async_synic_update function to set
synic->sctl_enabled to true. A true value of synic->sctl_enabled is required
before creating SINT routes using the hyperv_sint_route_new() function.
If kvm_hv_handle_exit returns 0 for KVM_EXIT_HYPERV_SYNIC, the current QEMU
vCPU thread may return to KVM and enter the guest VM before running
async_synic_update. In such case, the hyperv_synic test’s subsequent call to
synic_ctl(HV_TEST_DEV_SINT_ROUTE_CREATE, ...) immediately after writing to
HV_X64_MSR_SCONTROL can cause QEMU’s hyperv_sint_route_new() function to return
prematurely (because synic->sctl_enabled is false).
If the SINT route is not created successfully, the SINT interrupt will not be
fired, resulting in a timeout error in the hyperv_synic test.
Fixes: 267e071bd6 (“hyperv: make overlay pages for SynIC”)
Suggested-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Dongsheng Zhang <dongsheng.x.zhang@intel.com>
Message-ID: <20240521200114.11588-1-dongsheng.x.zhang@intel.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 84d4b72854)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Remove gtk_widget_get_scale_factor() usage from the calculation of
the motion events in the GTK backend to make it work correctly on
environments that have `gtk_widget_get_scale_factor() != 1`.
This scale factor usage had been introduced in the commit f14aab420c and
at that time the window size was used for calculating the things and it
was working correctly. However, in the commit 2f31663ed4 the logic
switched to use the widget size instead of window size and because of
the change the usage of scale factor becomes invalid (since widgets use
`vc->gfx.scale_{x, y}` for scaling).
Tested on Crostini on ChromeOS (15823.51.0) with an external display.
Fixes: 2f31663ed4 ("ui/gtk: use widget size for cursor motion event")
Fixes: f14aab420c ("ui: fix incorrect pointer position on highdpi with
gtk")
(f14aab420c is 95c9059e66 in stable-7.2)
Signed-off-by: hikalium <hikalium@hikalium.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20240512111435.30121-3-hikalium@hikalium.com>
(cherry picked from commit 37e9141501)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the manual, 32-bit vs 64-bit is governed by REX.W
and REX ignores the 0x66 prefix. This can be confirmed with this
program:
#include <stdio.h>
int main()
{
int x = 0x12340000;
int y;
asm("popcntl %1, %0" : "=r" (y) : "r" (x)); printf("%x\n", y);
asm("mov $-1, %0; .byte 0x66; popcntl %1, %0" : "+r" (y) : "r" (x)); printf("%x\n", y);
asm("mov $-1, %0; .byte 0x66; popcntq %q1, %q0" : "+r" (y) : "r" (x)); printf("%x\n", y);
}
which prints 5/ffff0000/5 on real hardware and 5/ffff0000/ffff0000
on QEMU.
Cc: qemu-stable@nongnu.org
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 41c685dc59)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: drop removal of mo_64_32() helper function in target/i386/tcg/translate.c
due to missing-in-7.2 v9.0.0-542-gaef4f4affde2
"target/i386: remove now-converted opcodes from old decoder"
which removed other user of it)
When emulated with QEMU, interrupts will never come in the following
loop. However, if the NOP instruction is uncommented, interrupts will
fire as normal.
loop:
cli
call do_sti
jmp loop
do_sti:
sti
# nop
ret
This behavior is different from that of a real processor. For example,
if KVM is enabled, interrupts will always fire regardless of whether the
NOP instruction is commented or not. Also, the Intel Software Developer
Manual states that after the STI instruction is executed, the interrupt
inhibit should end as soon as the next instruction (e.g., the RET
instruction if the NOP instruction is commented) is executed.
This problem is caused because the previous code may choose not to end
the TB even if the HF_INHIBIT_IRQ_MASK has just been reset (e.g., in the
case where the STI instruction is immediately followed by the RET
instruction), so that IRQs may not have a change to trigger. This commit
fixes the problem by always terminating the current TB to give IRQs a
chance to trigger when HF_INHIBIT_IRQ_MASK is reset.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Message-ID: <20240415064518.4951-4-lrh2000@pku.edu.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 6a5a63f74b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup due to missing-in-7.2
v8.1.0-1189-gad75a51e84 "tcg: Rename cpu_env to tcg_env")
The DMA descriptor structures for this device have
a set of "address extension" fields which extend the 32
bit source addresses with an extra 16 bits to give a
48 bit address:
https://docs.amd.com/r/en-US/ug1085-zynq-ultrascale-trm/ADDR_EXT-Field
However, we misimplemented this address extension in several ways:
* we only extracted 12 bits of the extension fields, not 16
* we didn't shift the extension field up far enough
* we accidentally did the shift as 32-bit arithmetic, which
meant that we would have an overflow instead of setting
bits [47:32] of the resulting 64-bit address
Add a type cast and use extract64() instead of extract32()
to avoid integer overflow on addition. Fix bit fields
extraction according to documentation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: d3c6369a96 ("introduce xlnx-dpdma")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Message-id: 20240428181131.23801-1-adiupina@astralinux.ru
[PMM: adjusted commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 4b00855f0e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cirrus-CI introduced limitations to the free CI minutes. To avoid that
we are consuming them too fast, let's drop the usual targets that are
not that important since they are either a subset of another target
(like i386 or ppc being a subset of x86_64 or ppc64 respectively), or
since there is still a similar target with the opposite endianness
(like xtensa/xtensael, microblaze/microblazeel etc.).
Message-ID: <20240429100113.53357-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit a88a04906b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
nbd_negotiate() is already marked coroutine_fn. And given the fix in
the previous patch to have nbd_negotiate_handle_starttls not create
and wait on a g_main_loop (as that would violate coroutine
constraints), it is worth marking the rest of the related static
functions reachable only during option negotiation as also being
coroutine_fn.
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240408160214.1200629-6-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
[eblake: drop one spurious coroutine_fn marking]
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit 4fa333e08d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixups in nbd/server.c for v8.1.0-1366-gfd358d83901d
"nbd/server: Refactor list of negotiated meta contexts")
Coroutines are not supposed to block. Instead, they should yield.
The client performs TLS upgrade outside of an AIOContext, during
synchronous handshake; this still requires g_main_loop. But the
server responds to TLS upgrade inside a coroutine, so a nested
g_main_loop is wrong. Since the two callbacks no longer share more
than the setting of data.complete and data.error, it's just as easy to
use static helpers instead of trying to share a common code path. It
is also possible to add assertions that no other code is interfering
with the eventual path to qio reaching the callback, whether or not it
required a yield or main loop.
Fixes: f95910f ("nbd: implement TLS support in the protocol negotiation")
Signed-off-by: Zhu Yangyang <zhuyangyang14@huawei.com>
[eblake: move callbacks to their use point, add assertions]
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20240408160214.1200629-5-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
(cherry picked from commit ae6d91a7e9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The OpenSBI build has been using docker:19.03.1, which appears to be old
enough that v2 of the manifest is no longer supported. Something has
started serving us those manifests, resulting in errors along the lines
of
$ docker build --cache-from $IMAGE_TAG --tag $CI_REGISTRY_IMAGE:$CI_COMMIT_SHA --tag $IMAGE_TAG .gitlab-ci.d/opensbi
Step 1/7 : FROM ubuntu:18.04
18.04: Pulling from library/ubuntu
mediaType in manifest should be 'application/vnd.docker.distribution.manifest.v2+json' not 'application/vnd.oci.image.manifest.v1+json'
This moves to docker:stable, as was suggested by the template. It also
adds the python3 package via apt, as OpenSBI requires that to build.
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-ID: <20230303202448.11911-2-palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
(cherry picked from commit 7bc1286b81)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we introduced this Gitlab-CI job in commit 71920809ce
("gitlab-ci.yml: Add jobs to build EDK2 firmware binaries"),
the naive plan was to have reproducible binaries by downloading
what this job would build, testing it and eventually committing
it. With retrospective, nothing happened 3 years later and this
job is just bitrotting:
Step 1/3 : FROM ubuntu:18.04
18.04: Pulling from library/ubuntu
mediaType in manifest should be
'application/vnd.docker.distribution.manifest.v2+json' not
'application/vnd.oci.image.manifest.v1+json'
Remove this job to avoid wasting maintenance and CI ressources.
Reported-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230310133247.39268-1-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 690ceb7193)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Initialize the machine specific max_cpus limit as per the maximum range
of CPU IPIs available. Keeping between 4096 to 8192 will throw IRQ not
free error due to XIVE/XICS limitation and keeping beyond 8192 will hit
assert in tcg_region_init or spapr_xive_claim_irq.
Logs:
Without patch fix:
[root@host build]# qemu-system-ppc64 -accel tcg -smp 10,maxcpus=4097
qemu-system-ppc64: IRQ 4096 is not free
[root@host build]#
On LPAR:
[root@host build]# qemu-system-ppc64 -accel tcg -smp 10,maxcpus=8193
**
ERROR:../tcg/region.c:774:tcg_region_init: assertion failed:
(region_size >= 2 * page_size)
Bail out! ERROR:../tcg/region.c:774:tcg_region_init: assertion failed:
(region_size >= 2 * page_size)
Aborted (core dumped)
[root@host build]#
On x86:
[root@host build]# qemu-system-ppc64 -accel tcg -smp 10,maxcpus=8193
qemu-system-ppc64: ../hw/intc/spapr_xive.c:596: spapr_xive_claim_irq:
Assertion `lisn < xive->nr_irqs' failed.
Aborted (core dumped)
[root@host build]#
With patch fix:
[root@host build]# qemu-system-ppc64 -accel tcg -smp 10,maxcpus=4097
qemu-system-ppc64: Invalid SMP CPUs 4097. The max CPUs supported by
machine 'pseries-8.2' is 4096
[root@host build]#
Reported-by: Kowshik Jois <kowsjois@linux.ibm.com>
Tested-by: Kowshik Jois <kowsjois@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit c4f91d7b7b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
spapr_irq_init currently uses existing macro SPAPR_XIRQ_BASE to refer to
the range of CPU IPIs during initialization of nr-irqs property.
It is more appropriate to have its own define which can be further
reused as appropriate for correct interpretation.
Suggested-by: Cedric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Kowshik Jois <kowsjois@linux.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 2df5c1f5b0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CHECK_NOT_DELAY_SLOT is correctly applied to the branch-related
instructions, but not to the PC-relative mov* instructions.
I verified the existence of an illegal slot exception on a SH7091 when
any of these instructions are attempted inside a delay slot.
This also matches the behavior described in the SH-4 ISA manual.
Signed-off-by: Zack Buhman <zack@buhman.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240407150705.5965-1-zack@buhman.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewd-by: Yoshinori Sato <ysato@users.sourceforge.jp>
(cherry picked from commit b754cb2dcd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: trivial context (whitespace before comments) fixup)
Per "SD Host Controller Standard Specification Version 3.00":
* 2.2.5 Transfer Mode Register (Offset 00Ch)
Writes to this register shall be ignored when the Command
Inhibit (DAT) in the Present State register is 1.
Do not update the TRNMOD register when Command Inhibit (DAT)
bit is set to avoid the present-status register going out of
sync, leading to malicious guest using DMA mode and overflowing
the FIFO buffer:
$ cat << EOF | qemu-system-i386 \
-display none -nographic -nodefaults \
-machine accel=qtest -m 512M \
-device sdhci-pci,sd-spec-version=3 \
-device sd-card,drive=mydrive \
-drive if=none,index=0,file=null-co://,format=raw,id=mydrive \
-qtest stdio
outl 0xcf8 0x80001013
outl 0xcfc 0x91
outl 0xcf8 0x80001001
outl 0xcfc 0x06000000
write 0x9100002c 0x1 0x05
write 0x91000058 0x1 0x16
write 0x91000005 0x1 0x04
write 0x91000028 0x1 0x08
write 0x16 0x1 0x21
write 0x19 0x1 0x20
write 0x9100000c 0x1 0x01
write 0x9100000e 0x1 0x20
write 0x9100000f 0x1 0x00
write 0x9100000c 0x1 0x00
write 0x91000020 0x1 0x00
EOF
Stack trace (part):
=================================================================
==89993==ERROR: AddressSanitizer: heap-buffer-overflow on address
0x615000029900 at pc 0x55d5f885700d bp 0x7ffc1e1e9470 sp 0x7ffc1e1e9468
WRITE of size 1 at 0x615000029900 thread T0
#0 0x55d5f885700c in sdhci_write_dataport hw/sd/sdhci.c:564:39
#1 0x55d5f8849150 in sdhci_write hw/sd/sdhci.c:1223:13
#2 0x55d5fa01db63 in memory_region_write_accessor system/memory.c:497:5
#3 0x55d5fa01d245 in access_with_adjusted_size system/memory.c:573:18
#4 0x55d5fa01b1a9 in memory_region_dispatch_write system/memory.c:1521:16
#5 0x55d5fa09f5c9 in flatview_write_continue system/physmem.c:2711:23
#6 0x55d5fa08f78b in flatview_write system/physmem.c:2753:12
#7 0x55d5fa08f258 in address_space_write system/physmem.c:2860:18
...
0x615000029900 is located 0 bytes to the right of 512-byte region
[0x615000029700,0x615000029900) allocated by thread T0 here:
#0 0x55d5f7237b27 in __interceptor_calloc
#1 0x7f9e36dd4c50 in g_malloc0
#2 0x55d5f88672f7 in sdhci_pci_realize hw/sd/sdhci-pci.c:36:5
#3 0x55d5f844b582 in pci_qdev_realize hw/pci/pci.c:2092:9
#4 0x55d5fa2ee74b in device_set_realized hw/core/qdev.c:510:13
#5 0x55d5fa325bfb in property_set_bool qom/object.c:2358:5
#6 0x55d5fa31ea45 in object_property_set qom/object.c:1472:5
#7 0x55d5fa332509 in object_property_set_qobject om/qom-qobject.c:28:10
#8 0x55d5fa31f6ed in object_property_set_bool qom/object.c:1541:15
#9 0x55d5fa2e2948 in qdev_realize hw/core/qdev.c:292:12
#10 0x55d5f8eed3f1 in qdev_device_add_from_qdict system/qdev-monitor.c:719:10
#11 0x55d5f8eef7ff in qdev_device_add system/qdev-monitor.c:738:11
#12 0x55d5f8f211f0 in device_init_func system/vl.c:1200:11
#13 0x55d5fad0877d in qemu_opts_foreach util/qemu-option.c:1135:14
#14 0x55d5f8f0df9c in qemu_create_cli_devices system/vl.c:2638:5
#15 0x55d5f8f0db24 in qmp_x_exit_preconfig system/vl.c:2706:5
#16 0x55d5f8f14dc0 in qemu_init system/vl.c:3737:9
...
SUMMARY: AddressSanitizer: heap-buffer-overflow hw/sd/sdhci.c:564:39
in sdhci_write_dataport
Add assertions to ensure the fifo_buffer[] is not overflowed by
malicious accesses to the Buffer Data Port register.
Fixes: CVE-2024-3447
Cc: qemu-stable@nongnu.org
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Buglink: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=58813
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <CAFEAcA9iLiv1XGTGKeopgMa8Y9+8kvptvsb8z2OBeuy+5=NUfg@mail.gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409145524.27913-1-philmd@linaro.org>
(cherry picked from commit 9e4b27ca6b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The magic 2048 is explained in the LAN9211 datasheet (DS00002414A)
in chapter 1.4, "10/100 Ethernet MAC":
The MAC Interface Layer (MIL), within the MAC, contains a
2K Byte transmit and a 128 Byte receive FIFO which is separate
from the TX and RX FIFOs. [...]
Note, the use of the constant in lan9118_receive() reveals that
our implementation is using the same buffer for both tx and rx.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240409133801.23503-2-philmd@linaro.org>
(cherry picked from commit a45223467e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the MAC Interface Layer (MIL) transmit FIFO is full,
truncate the packet, and raise the Transmitter Error (TXE)
flag.
Broken since model introduction in commit 2a42499017
("LAN9118 emulation").
When using the reproducer from
https://gitlab.com/qemu-project/qemu/-/issues/2267 we get:
hw/net/lan9118.c:798:17: runtime error:
index 2048 out of bounds for type 'uint8_t[2048]' (aka 'unsigned char[2048]')
#0 0x563ec9a057b1 in tx_fifo_push hw/net/lan9118.c:798:43
#1 0x563ec99fbb28 in lan9118_writel hw/net/lan9118.c:1042:9
#2 0x563ec99f2de2 in lan9118_16bit_mode_write hw/net/lan9118.c:1205:9
#3 0x563ecbf78013 in memory_region_write_accessor system/memory.c:497:5
#4 0x563ecbf776f5 in access_with_adjusted_size system/memory.c:573:18
#5 0x563ecbf75643 in memory_region_dispatch_write system/memory.c:1521:16
#6 0x563ecc01bade in flatview_write_continue_step system/physmem.c:2713:18
#7 0x563ecc01b374 in flatview_write_continue system/physmem.c:2743:19
#8 0x563ecbff1c9b in flatview_write system/physmem.c:2774:12
#9 0x563ecbff1768 in address_space_write system/physmem.c:2894:18
...
[*] LAN9118 DS00002266B.pdf, Table 5.3.3 "INTERRUPT STATUS REGISTER"
Cc: qemu-stable@nongnu.org
Reported-by: Will Lester
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2267
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240409133801.23503-3-philmd@linaro.org>
(cherry picked from commit ad766d603f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
nand_command() and nand_getio() don't check @offset points
into the block, nor the available data length (s->iolen) is
not negative.
In order to fix:
- check the offset is in range in nand_blk_load_NAND_PAGE_SIZE(),
- do not set @iolen if blk_load() failed.
Reproducer:
$ cat << EOF | qemu-system-arm -machine tosa \
-monitor none -serial none \
-display none -qtest stdio
write 0x10000111 0x1 0xca
write 0x10000104 0x1 0x47
write 0x1000ca04 0x1 0xd7
write 0x1000ca01 0x1 0xe0
write 0x1000ca04 0x1 0x71
write 0x1000ca00 0x1 0x50
write 0x1000ca04 0x1 0xd7
read 0x1000ca02 0x1
write 0x1000ca01 0x1 0x10
EOF
=================================================================
==15750==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x61f000000de0
at pc 0x560e61557210 bp 0x7ffcfc4a59f0 sp 0x7ffcfc4a59e8
READ of size 1 at 0x61f000000de0 thread T0
#0 0x560e6155720f in mem_and hw/block/nand.c:101:20
#1 0x560e6155ac9c in nand_blk_write_512 hw/block/nand.c:663:9
#2 0x560e61544200 in nand_command hw/block/nand.c:293:13
#3 0x560e6153cc83 in nand_setio hw/block/nand.c:520:13
#4 0x560e61a0a69e in tc6393xb_nand_writeb hw/display/tc6393xb.c:380:13
#5 0x560e619f9bf7 in tc6393xb_writeb hw/display/tc6393xb.c:524:9
#6 0x560e647c7d03 in memory_region_write_accessor softmmu/memory.c:492:5
#7 0x560e647c7641 in access_with_adjusted_size softmmu/memory.c:554:18
#8 0x560e647c5f66 in memory_region_dispatch_write softmmu/memory.c:1514:16
#9 0x560e6485409e in flatview_write_continue softmmu/physmem.c:2825:23
#10 0x560e648421eb in flatview_write softmmu/physmem.c:2867:12
#11 0x560e64841ca8 in address_space_write softmmu/physmem.c:2963:18
#12 0x560e61170162 in qemu_writeb tests/qtest/videzzo/videzzo_qemu.c:1080:5
#13 0x560e6116eef7 in dispatch_mmio_write tests/qtest/videzzo/videzzo_qemu.c:1227:28
0x61f000000de0 is located 0 bytes to the right of 3424-byte region [0x61f000000080,0x61f000000de0)
allocated by thread T0 here:
#0 0x560e611276cf in malloc /root/llvm-project/compiler-rt/lib/asan/asan_malloc_linux.cpp:145:3
#1 0x7f7959a87e98 in g_malloc (/lib/x86_64-linux-gnu/libglib-2.0.so.0+0x57e98)
#2 0x560e64b98871 in object_new qom/object.c:749:12
#3 0x560e64b5d1a1 in qdev_new hw/core/qdev.c:153:19
#4 0x560e61547ea5 in nand_init hw/block/nand.c:639:11
#5 0x560e619f8772 in tc6393xb_init hw/display/tc6393xb.c:558:16
#6 0x560e6390bad2 in tosa_init hw/arm/tosa.c:250:12
SUMMARY: AddressSanitizer: heap-buffer-overflow hw/block/nand.c:101:20 in mem_and
==15750==ABORTING
Broken since introduction in commit 3e3d5815cb ("NAND Flash memory
emulation and ECC calculation helpers for use by NAND controllers").
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1445
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1446
Reported-by: Qiang Liu <cyruscyliu@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409135944.24997-4-philmd@linaro.org>
(cherry picked from commit d39fdfff34)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Introduce virtio_bh_new_guarded(), similar to qemu_bh_new_guarded()
but using the transport memory guard, instead of the device one
(there can only be one virtio device per virtio bus).
Inspired-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240409105537.18308-2-philmd@linaro.org>
(cherry picked from commit ec0504b989)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: trivial #include context fixup in include/hw/virtio/virtio.h)
In the event of writing many chains of descriptors, the device must
write just the id of the last buffer in the descriptor chain, skip
forward the number of descriptors in the chain, and then repeat the
operations for the rest of chains.
Current QEMU code writes all the buffer ids consecutively, and then
skips all the buffers altogether. This is a bug, and can be reproduced
with a VirtIONet device with _F_MRG_RXBUB and without
_F_INDIRECT_DESC:
If a virtio-net device has the VIRTIO_NET_F_MRG_RXBUF feature
but not the VIRTIO_RING_F_INDIRECT_DESC feature,
'VirtIONetQueue->rx_vq' will use the merge feature
to store data in multiple 'elems'.
The 'num_buffers' in the virtio header indicates how many elements are merged.
If the value of 'num_buffers' is greater than 1,
all the merged elements will be filled into the descriptor ring.
The 'idx' of the elements should be the value of 'vq->used_idx' plus 'ndescs'.
Fixes: 86044b24e8 ("virtio: basic packed virtqueue support")
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Wafer <wafer@jaguarmicro.com>
Message-Id: <20240407015451.5228-2-wafer@jaguarmicro.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 2d9a31b3c2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When vhost-user or vhost-kernel is handling virtio net datapath,
QEMU should not touch used ring.
But with vhost-user socket reconnect scenario, in a very rare case
(has pending kick event). VRING_USED_F_NO_NOTIFY is set by QEMU in
following code path:
#0 virtio_queue_split_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:511
#1 0x0000559d6dbf033b in virtio_queue_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:576
#2 0x0000559d6dbbbdbc in virtio_net_handle_tx_bh (vdev=0x559d703a6aa0, vq=0x7ff5f4c920a8) at ../hw/net/virtio-net.c:2801
#3 0x0000559d6dbf4791 in virtio_queue_notify_vq (vq=0x7ff5f4c920a8) at ../hw/virtio/virtio.c:2248
#4 0x0000559d6dbf79da in virtio_queue_host_notifier_read (n=0x7ff5f4c9211c) at ../hw/virtio/virtio.c:3525
#5 0x0000559d6d9a5814 in virtio_bus_cleanup_host_notifier (bus=0x559d703a6a20, n=1) at ../hw/virtio/virtio-bus.c:321
#6 0x0000559d6dbf83c9 in virtio_device_stop_ioeventfd_impl (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3774
#7 0x0000559d6d9a55c8 in virtio_bus_stop_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:259
#8 0x0000559d6d9a53e8 in virtio_bus_grab_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:199
#9 0x0000559d6dbf841c in virtio_device_grab_ioeventfd (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3783
#10 0x0000559d6d9bde18 in vhost_dev_enable_notifiers (hdev=0x559d707edd70, vdev=0x559d703a6aa0) at ../hw/virtio/vhost.c:1592
#11 0x0000559d6d89a0b8 in vhost_net_start_one (net=0x559d707edd70, dev=0x559d703a6aa0) at ../hw/net/vhost_net.c:266
#12 0x0000559d6d89a6df in vhost_net_start (dev=0x559d703a6aa0, ncs=0x559d7048d890, data_queue_pairs=31, cvq=0) at ../hw/net/vhost_net.c:412
#13 0x0000559d6dbb5b89 in virtio_net_vhost_status (n=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:311
#14 0x0000559d6dbb5e34 in virtio_net_set_status (vdev=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:392
#15 0x0000559d6dbb60d8 in virtio_net_set_link_status (nc=0x559d7048d890) at ../hw/net/virtio-net.c:455
#16 0x0000559d6da64863 in qmp_set_link (name=0x559d6f0b83d0 "hostnet1", up=true, errp=0x7ffdd76569f0) at ../net/net.c:1459
#17 0x0000559d6da7226e in net_vhost_user_event (opaque=0x559d6f0b83d0, event=CHR_EVENT_OPENED) at ../net/vhost-user.c:301
#18 0x0000559d6ddc7f63 in chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:62
#19 0x0000559d6ddc7fdc in qemu_chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:82
This issue causes guest kernel stop kicking device and traffic stop.
Add vhost_started check in virtio_net_handle_tx_bh to fix this wrong
VRING_USED_F_NO_NOTIFY set.
Signed-off-by: Yajun Wu <yajunw@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20240402045109.97729-1-yajunw@nvidia.com>
[PMD: Use unlikely()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 4c54f5bc8e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If the group of the highest priority pending interrupt is disabled
via ICC_IGRPEN*, the ICC_HPPIR* registers should return
INTID_SPURIOUS, not the interrupt ID. (See the GIC architecture
specification pseudocode functions ICC_HPPIR1_EL1[] and
HighestPriorityPendingInterrupt().)
Make HPPIR reads honour the group disable, the way we already do
when determining whether to preempt in icc_hppi_can_preempt().
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240328153333.2522667-1-peter.maydell@linaro.org
(cherry picked from commit 44e25fbc19)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The 'sign' computation is attempting to locate the sign bit that has
been repeated, so that we can test if that bit is known zero. That
computation can be zero if there are no known sign repetitions.
Cc: qemu-stable@nongnu.org
Fixes: 93a967fbb5 ("tcg/optimize: Propagate sign info for shifting")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2248
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 2911e9b95f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: trivial context fixup in tests/tcg/aarch64/Makefile.target)
virtio_net_guest_notifier_pending() and virtio_net_guest_notifier_mask()
checked VIRTIO_NET_F_MQ to know there are multiple queues, but
VIRTIO_NET_F_RSS also enables multiple queues. Refer to n->multiqueue,
which is set to true either of VIRTIO_NET_F_MQ or VIRTIO_NET_F_RSS is
enabled.
Fixes: 68b0a6395f ("virtio-net: align ctrl_vq index for non-mq guest for vhost_vdpa")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 1c188fc8cb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In qemu monitor mode, when we use gpa2hva command to print the host
virtual address corresponding to a guest physical address, if the gpa is
not in RAM, the error message is below:
(qemu) gpa2hva 0x750000000
Memory at address 0x750000000is not RAM
A space is missed between '0x750000000' and 'is'.
Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com>
Fixes: e9628441df ("hmp: gpa2hva and gpa2hpa hostaddr command")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dave@treblig.org>
Message-ID: <20240319021610.2423844-1-ruansy.fnst@fujitsu.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit a158c63b3b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: in 7.2. it is in monitor/misc.c, not in monitor/hmp-cmds-target.c)
The io_timeout property, introduced in c9b6609 (part of 6.0) is
silently overwritten by the hardcoded default value of 30 seconds
(DEFAULT_IO_TIMEOUT) in scsi_generic_realize because that function is
being called after the properties have already been applied.
The property definition already has a default value which is applied
correctly when no value is explicitly set, so we can just remove the
code which overrides the io_timeout completely.
This has been tested by stracing SG_IO operations with the io_timeout
property set and unset and now sets the timeout field in the ioctl
request to the proper value.
Fixes: c9b6609b69 ("scsi: make io_timeout configurable")
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Message-ID: <20240315145831.2531695-1-lorenz@brun.one>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 7c7a9f578e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu-system-loongarch64 assert failed with the option '-d int',
the helper_idle() raise an exception EXCP_HLT, but the exception name is undefined.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240321123606.1704900-1-gaosong@loongson.cn>
(cherry picked from commit 1590154ee4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup for lack of 2 commits adding new entries into excp_names[]:
v8.0.0-514-ga3f3db5cda "target/loongarch: Add CHECK_SXE maccro for check LSX enable" and
v8.1.0-801-gb8f1bdf3d1 "target/loongarch: check_vec support check LASX instructions")
monitor_puts() doesn't check the monitor pointer, but do_inject_x86_mce()
may have a parameter with NULL monitor pointer. Revert monitor_puts() in
do_inject_x86_mce() to fix, then the fact that we send the same message to
monitor and log is again more obvious.
Fixes: bf0c50d4aa (monitor: expose monitor_puts to rest of code)
Reviwed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Message-ID: <20240320083640.523287-1-tao1.su@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 7fd226b047)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The low bit of MMU indices for x86 TCG indicates whether the processor is
in 32-bit mode and therefore linear addresses have to be masked to 32 bits.
However, the index was computed incorrectly, leading to possible conflicts
in the TLB for any address above 4G.
Analyzed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: b1661801c1 ("target/i386: Fix physical address truncation", 2024-02-28)
Fixes: 1c15f97b4f ("target/i386: Fix physical address truncation" in stable-7.2)
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2206
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 2cc68629a6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: move changes for x86_cpu_mmu_index() to cpu_mmu_index() due to missing
v8.2.0-1030-gace0c5fe59 "target/i386: Populate CPUClass.mmu_index")
Accesses from a 32-bit environment (32-bit code segment for instruction
accesses, EFER.LMA==0 for processor accesses) have to mask away the
upper 32 bits of the address. While a bit wasteful, the easiest way
to do so is to use separate MMU indexes. These days, QEMU anyway is
compiled with a fixed value for NB_MMU_MODES. Split MMU_USER_IDX,
MMU_KSMAP_IDX and MMU_KNOSMAP_IDX in two.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 90f641531c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: move changes for x86_cpu_mmu_index() to cpu_mmu_index() due to missing
v8.2.0-1030-gace0c5fe5950 "target/i386: Populate CPUClass.mmu_index"
Increase NB_MMU_MODES from 5 to 8 in target/i386/cpu-param.h due to missing
v7.2.0-2640-gffd824f3f32d "include/exec: Set default NB_MMU_MODES to 16"
v7.2.0-2647-g6787318a5d86 "target/i386: Remove NB_MMU_MODES define"
which relaxed upper limit of MMU index for i386, since this commit starts
using MMU_NESTED_IDX=7.
Thanks Zhao Liu and Paolo Bonzini for the analisys and suggestions.
)
Remove knowledge of specific MMU indexes (other than MMU_NESTED_IDX and
MMU_PHYS_IDX) from mmu_translate(). This will make it possible to split
32-bit and 64-bit MMU indexes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 5f97afe254)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in target/i386/cpu.h due to other changes in that area)
We're seeing timeouts for this test on CI runs (specifically for
ubuntu-20.04-s390x-all). It doesn't fail consistently, but even the
successful runs take about 27 or 28 seconds, which is not very far from
the 30 seconds timeout.
Bump the timeout a bit to make failure less likely even on this CI host.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240125165803.48373-1-kwolf@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 63b18312d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When running the tests in slow mode on a very loaded system and with
--enable-debug, the test-crypto-block can take longer than 4 minutes.
Bump the timeout to 5 minutes to make sure that it also passes in
such situations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-15-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
(cherry picked from commit e1b363e328)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When running the tests in slow mode on a very loaded system and with
--enable-debug, the test-aio-multithread can take longer than 1 minute.
Bump the timeout to two minutes to make sure that it also passes in
such situations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-14-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
(cherry picked from commit c45f8f1aef)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The block .save_setup() handler calls a helper routine
init_blk_migration() which builds a list of block devices to take into
account for migration. When one device is found to be empty (sectors
== 0), the loop exits and all the remaining devices are ignored. This
is a regression introduced when bdrv_iterate() was removed.
Change that by skipping only empty devices.
Cc: Markus Armbruster <armbru@redhat.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Fixes: fea68bb6e9 ("block: Eliminate bdrv_iterate(), use bdrv_next()")
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Link: https://lore.kernel.org/r/20240312120431.550054-1-clg@redhat.com
[peterx: fix "Suggested-by:"]
Signed-off-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit 2e128776dc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
With a numa set up such as
-numa nodeid=0,cpus=0 \
-numa nodeid=1,memdev=mem \
-numa nodeid=2,cpus=1
and appropriate hmat_lb entries the initiator list is correctly
computed and writen to HMAT as 0,2 but then the LB data is accessed
using the node id (here 2), landing outside the entry_list array.
Stash the reverse lookup when writing the initiator list and use
it to get the correct array index index.
Fixes: 4586a2cb83 ("hmat acpi: Build System Locality Latency and Bandwidth Information Structure(s)")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240307160326.31570-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 74e2845c5f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
nvme_sriov_pre_write_ctrl() used to directly inspect SR-IOV
configurations to know the number of VFs being disabled due to SR-IOV
configuration writes, but the logic was flawed and resulted in
out-of-bound memory access.
It assumed PCI_SRIOV_NUM_VF always has the number of currently enabled
VFs, but it actually doesn't in the following cases:
- PCI_SRIOV_NUM_VF has been set but PCI_SRIOV_CTRL_VFE has never been.
- PCI_SRIOV_NUM_VF was written after PCI_SRIOV_CTRL_VFE was set.
- VFs were only partially enabled because of realization failure.
It is a responsibility of pcie_sriov to interpret SR-IOV configurations
and pcie_sriov does it correctly, so use pcie_sriov_num_vfs(), which it
provides, to get the number of enabled VFs before and after SR-IOV
configuration writes.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2024-26328
Fixes: 11871f53ef ("hw/nvme: Add support for the Virtualization Management command")
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-1-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 91bb64a8d2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
igb can use this function to change its behavior depending on the
number of virtual functions currently enabled.
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 31180dbdca)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: needed for v8.2.0-2290-g91bb64a8d2
"hw/nvme: Use pcie_sriov_num_vfs()" (CVE-2024-26328))
Commit 1901b4967c ("hw/block/nvme: move msix table and pba to BAR 0")
moved the MSI-X table and PBA to BAR 0 to make room for enabling CMR and
PMR at the same time. As reported by Julien Grall in #2184, this breaks
migration through system hibernation.
Add a machine compatibility parameter and set it on machines pre 6.0 to
enable the old behavior automatically, restoring the hibernation
migration support.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2184
Fixes: 1901b4967c ("hw/block/nvme: move msix table and pba to BAR 0")
Reported-by: Julien Grall julien@xen.org
Tested-by: Julien Grall julien@xen.org
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit fa905f65c5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Generalize the mbar size helper such that it can handle cases where the
MSI-X table and PBA are expected to be in an exclusive bar.
Cc: qemu-stable@nongnu.org
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit ee7bda4d38)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, when a VF is created, it uses the 'params' object of the PF
as it is. In other words, the 'params.serial' string memory area is also
shared. In this situation, if the VF is removed from the system, the
PF's 'params.serial' object is released with object_finalize() followed
by object_property_del_all() which release the memory for 'serial'
property. If that happens, the next VF created will inherit a serial
from a corrupted memory area.
If this happens, an error will occur when comparing subsys->serial and
n->params.serial in the nvme_subsys_register_ctrl() function.
Cc: qemu-stable@nongnu.org
Fixes: 44c2c09488 ("hw/nvme: Add support for SR-IOV")
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit 4f0a4a3d58)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace the local Error variable with errp and ERRP_GUARD() and change
the return value to bool.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit 973f76cf77)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: needed for v8.2.0-2319-gfa905f65c5
"hw/nvme: add machine compatibility parameter to enable msix exclusive bar")
Remove an unnecessary local Error value in nvme_realize(). In the
process, change nvme_check_constraints() to return a bool.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit 784fd35387)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: needed for v8.2.0-2319-gfa905f65c5
"hw/nvme: add machine compatibility parameter to enable msix exclusive bar")
On resume e1000e_vm_state_change() always calls e1000e_autoneg_resume()
that sets link_down to false, and thus activates the link even
if we have disabled it.
The problem can be reproduced starting qemu in paused state (-S) and
then set the link to down. When we resume the machine the link appears
to be up.
Reproducer:
# qemu-system-x86_64 ... -device e1000e,netdev=netdev0,id=net0 -S
{"execute": "qmp_capabilities" }
{"execute": "set_link", "arguments": {"name": "net0", "up": false}}
{"execute": "cont" }
To fix the problem, merge the content of e1000e_vm_state_change()
into e1000e_core_post_load() as e1000 does.
Buglink: https://issues.redhat.com/browse/RHEL-21867
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Suggested-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 4cadf10234)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For a long time, we provide two compression formats in the
download area, .bz2 and .xz. There's absolutely no reason
to provide two in parallel, .xz compresses better, and all
the links we use points to .xz. Downstream distributions
mostly use .xz too.
For the release maintenance providing two formats is definitely
extra burden too.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 9bc9e95119)
HP-UX 10.20 seems to make the lsi53c895a spinning on a memory location
under certain circumstances. As the SCSI controller and CPU are not
running at the same time this loop will never finish. After some
time, the check loop interrupts with a unexpected device disconnect.
This works, but is slow because the kernel resets the scsi controller.
Instead of signaling UDC, start a timer and exit the loop. Until the
timer fires, the CPU can process instructions which might changes the
memory location.
The limit of instructions is also reduced because scripts running on
the SCSI processor are usually very short. This keeps the time until
the loop is exit short.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240229204407.1699260-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 9876359990)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the maximum count of SCRIPTS instructions is reached, the code
stops execution and returns, but fails to decrement the reentrancy
counter. This effectively renders the SCSI controller unusable
because on next entry the reentrancy counter is still above the limit.
This bug was seen on HP-UX 10.20 which seems to trigger SCRIPTS
loops.
Fixes: b987718bbb ("hw/scsi/lsi53c895a: Fix reentrancy issues in the LSI controller (CVE-2023-0330)")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240128202214.2644768-1-svens@stackframe.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 8b09b7fe47)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Netbsd isn't happy with qemu lsi53c895a emulation:
cd0(esiop0:0:2:0): command with tag id 0 reset
esiop0: autoconfiguration error: phase mismatch without command
esiop0: autoconfiguration error: unhandled scsi interrupt, sist=0x80 sstat1=0x0 DSA=0x23a64b1 DSP=0x50
This is because lsi_bad_phase() triggers a phase mismatch, which
stops SCRIPT processing. However, after returning to
lsi_command_complete(), SCRIPT is restarted with lsi_resume_script().
Fix this by adding a return value to lsi_bad_phase(), and only resume
script processing when lsi_bad_phase() didn't trigger a host interrupt.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Helge Deller <deller@gmx.de>
Message-ID: <20240302214453.2071388-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit a9198b3132)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Original goal of addition of drain_call_rcu to qmp_device_add was to cover
the failure case of qdev_device_add. It seems call of drain_call_rcu was
misplaced in 7bed89958b what led to waiting for pending RCU callbacks
under happy path too. What led to overall performance degradation of
qmp_device_add.
In this patch call of drain_call_rcu moved under handling of failure of
qdev_device_add.
Signed-off-by: Dmitrii Gavrilov <ds-gavr@yandex-team.ru>
Message-ID: <20231103105602.90475-1-ds-gavr@yandex-team.ru>
Fixes: 7bed89958b ("device_core: use drain_call_rcu in in qmp_device_add", 2020-10-12)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 012b170173)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Some assemblers will complain about attempts to access
id_aa64zfr0_el1 and id_aa64smfr0_el1 by name if the test
binary isn't built for the right processor type:
/tmp/ccASXpLo.s:782: Error: selected processor does not support system register name 'id_aa64zfr0_el1'
/tmp/ccASXpLo.s:829: Error: selected processor does not support system register name 'id_aa64smfr0_el1'
However, these registers are in the ID space and are guaranteed to
read-as-zero on older CPUs, so the access is both safe and sensible.
Switch to using the S syntax, as we already do for ID_AA64ISAR2_EL1
and ID_AA64MMFR2_EL1. This allows us to drop the HAS_ARMV9_SME check
and the makefile machinery to adjust the CFLAGS for this test, so we
don't rely on having a sufficiently new compiler to be able to check
these registers.
This means we're actually testing the SME ID register: no released
GCC yet recognizes -march=armv9-a+sme, so that was always skipped.
It also avoids a future problem if we try to switch the "do we have
SME support in the toolchain" check from "in the compiler" to "in the
assembler" (at which point we would otherwise run into the above
errors).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 3dc2afeab2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: pick this for v8.0.0-2361-g1f51573f79
"target/arm: Fix SME full tile indexing")
In CPUID registers exposed to userspace, some registers were missing
and some fields were not exposed. This patch aligns exposed ID
registers and their fields with what the upstream kernel currently
exposes.
Specifically, the following new ID registers/fields are exposed to
userspace:
ID_AA64PFR1_EL1.BT: bits 3-0
ID_AA64PFR1_EL1.MTE: bits 11-8
ID_AA64PFR1_EL1.SME: bits 27-24
ID_AA64ZFR0_EL1.SVEver: bits 3-0
ID_AA64ZFR0_EL1.AES: bits 7-4
ID_AA64ZFR0_EL1.BitPerm: bits 19-16
ID_AA64ZFR0_EL1.BF16: bits 23-20
ID_AA64ZFR0_EL1.SHA3: bits 35-32
ID_AA64ZFR0_EL1.SM4: bits 43-40
ID_AA64ZFR0_EL1.I8MM: bits 47-44
ID_AA64ZFR0_EL1.F32MM: bits 55-52
ID_AA64ZFR0_EL1.F64MM: bits 59-56
ID_AA64SMFR0_EL1.F32F32: bit 32
ID_AA64SMFR0_EL1.B16F32: bit 34
ID_AA64SMFR0_EL1.F16F32: bit 35
ID_AA64SMFR0_EL1.I8I32: bits 39-36
ID_AA64SMFR0_EL1.F64F64: bit 48
ID_AA64SMFR0_EL1.I16I64: bits 55-52
ID_AA64SMFR0_EL1.FA64: bit 63
ID_AA64MMFR0_EL1.ECV: bits 63-60
ID_AA64MMFR1_EL1.AFP: bits 47-44
ID_AA64MMFR2_EL1.AT: bits 35-32
ID_AA64ISAR0_EL1.RNDR: bits 63-60
ID_AA64ISAR1_EL1.FRINTTS: bits 35-32
ID_AA64ISAR1_EL1.BF16: bits 47-44
ID_AA64ISAR1_EL1.DGH: bits 51-48
ID_AA64ISAR1_EL1.I8MM: bits 55-52
ID_AA64ISAR2_EL1.WFxT: bits 3-0
ID_AA64ISAR2_EL1.RPRES: bits 7-4
ID_AA64ISAR2_EL1.GPA3: bits 11-8
ID_AA64ISAR2_EL1.APA3: bits 15-12
The code is also refactored to use symbolic names for ID register fields
for better readability and maintainability.
The test case in tests/tcg/aarch64/sysregs.c is also updated to match
the intended behavior.
Signed-off-by: Zhuojia Shen <chaosdefinition@hotmail.com>
Message-id: DS7PR12MB6309FB585E10772928F14271ACE79@DS7PR12MB6309.namprd12.prod.outlook.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: use Sn_n_Cn_Cn_n syntax to work with older assemblers
that don't recognize id_aa64isar2_el1 and id_aa64mmfr2_el1]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit bc6bd20ee3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: pick this for v8.0.0-2361-g1f51573f79
"target/arm: Fix SME full tile indexing")
macOS Sonoma changes the NSView.clipsToBounds to false by default
where it was true in earlier version of macOS. This causes the window
contents to be occluded by the frame at the top of the window. This
fixes the issue by conditionally compiling the clipping on Sonoma to
true. NSView only exposes the clipToBounds in macOS 14 and so has
to be fixed via conditional compilation.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1994
Signed-off-by: David Parsons <dave@daveparsons.net>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-ID: <20240224140620.39200-1-dave@daveparsons.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit f5af80271a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The blockjob/complete_in_standby test is flaky and fails
intermittently in CI:
172/621 qemu:unit / test-blockjob
ERROR 0.26s killed by signal 6 SIGABRT
11:03:46 MALLOC_PERTURB_=176
G_TEST_SRCDIR=/Users/pm215/src/qemu-for-merges/tests/unit
G_TEST_BUILDDIR=/Users/pm215/src/qemu-for-merges/build/all/tests/unit
/Users/pm215/src/qemu-for-merges/build/all/tests/unit/test-blockjob
--tap -k
----------------------------------- output -----------------------------------
stdout:
# random seed: R02S8c79d6e1c01ce0b25475b2210a253242
1..9
# Start of blockjob tests
ok 1 /blockjob/ids
stderr:
Assertion failed: (job->status == JOB_STATUS_STANDBY), function
test_complete_in_standby, file ../../tests/unit/test-blockjob.c, line
499.
Seen on macOS/x86_64, FreeBSD 13/x86_64, msys2-64bit, eg:
https://gitlab.com/qemu-project/qemu/-/jobs/3872508803https://gitlab.com/qemu-project/qemu/-/jobs/3950667240
Disable this subtest until somebody has time to investigate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230317143534.1481947-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit b6903cbe3a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
display-vga-test currently tries to guess the usable VGA devices
according to the target architecture that is used for the test.
This of course does not work if QEMU has been built with the
"--without-default-devices" configure switch. To fix this, use the
qtest_has_device() function for the decision instead. This way
we can also consolidate most of the test functions into one single
function (that takes a parameter with the device name now), except
for the multihead test that tries to instantiate two devices and
thus is a little bit different.
Message-Id: <20230130104446.1286773-4-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit f2e57851b8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to g_tree_foreach() documentation:
"The tree may not be modified while iterating over it (you can't
add/remove items)."
compare_trees()/diff_tree() fail to respect this rule.
Historically GLib2 used a slice allocator for the GTree APIs
which did not immediately release the memory back to the system
allocator. As a result QEMU's use-after-free bug was not visible.
With GLib > 2.75.3 however, GLib2 has switched to using malloc
and now a SIGSEGV can be observed while running test-vmstate.
Get rid of the node removal within the tree traversal. Also
check the trees have the same number of nodes before the actual
diff.
Fixes: 9a85e4b8f6 ("migration: Support gtree migration")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1518
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit abe2c4bdb6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since Windows text files use CRLFs for all \n, the Windows version of QEMU
inserts a CR in the PCAP stream when a LF is encountered when using USB PCAP
files. This is due to the fact that the PCAP file is opened as TEXT instead
of BINARY.
To show an example, when using a very common protocol to USB disks, the BBB
protocol uses a 10-byte command packet. For example, the READ_CAPACITY(10)
command will have a command block length of 10 (0xA). When this 10-byte
command (part of the 31-byte CBW) is placed into the PCAP file, the Windows
file manager inserts a 0xD before the 0xA, turning the 31-byte CBW into a
32-byte CBW.
Actual CBW:
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0a 25 USBC...........%
0050 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...............
PCAP CBW
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0d 0a USBC............
0050 25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 %..............
I believe simply opening the PCAP file as BINARY instead of TEXT will fix
this issue.
Resolves: https://bugs.launchpad.net/qemu/+bug/2054889
Signed-off-by: Benjamin David Lunt <benlunt@fysnet.net>
Message-ID: <000101da6823$ce1bbf80$6a533e80$@fysnet.net>
[thuth: Break long line to avoid checkpatch.pl error]
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 5e02a4fdeb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Python is transitioning to a world where you're not allowed to use 'pip
install' outside of a virutal env by default. The rationale is to stop
use of pip clashing with distro provided python packages, which creates
a major headache on distro upgrades.
All our CI environments, however, are 100% disposable so the upgrade
headaches don't exist. Thus we can undo the python defaults to allow
pip to work.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20240222114038.2348718-1-berrange@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit a8bf9de2f4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The main problem is that "check-venv" is a .PHONY target will always
evaluate and trigger a full re-build of the VM images. While its
tempting to drop it from the dependencies that does introduce a
breakage on freshly configured builds.
Fortunately we do have the otherwise redundant --force flag for the
script which up until now was always on. If we make the usage of
--force conditional on dependencies other than check-venv triggering
the update we can avoid the costly rebuild and still run cleanly on a
fresh checkout.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2118
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-4-alex.bennee@linaro.org>
(cherry picked from commit 151b7dba39)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The A20 mask is only applied to the final memory access. Nested
page tables are always walked with the raw guest-physical address.
Unlike the previous patch, in this one the masking must be kept, but
it was done too early.
Cc: qemu-stable@nongnu.org
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit b5a9de3259)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If ptw_translate() does a MMU_PHYS_IDX access, the A20 mask is already
applied in get_physical_address(), which is called via probe_access_full()
and x86_cpu_tlb_fill().
If ptw_translate() on the other hand does a MMU_NESTED_IDX access,
the A20 mask must not be applied to the address that is looked up in
the nested page tables; it must be applied only to the addresses that
hold the NPT entries (which is achieved via MMU_PHYS_IDX, per the
previous paragraph).
Therefore, we can remove A20 masking from the computation of the page
table entry's address, and let get_physical_address() or mmu_translate()
apply it when they know they are returning a host-physical address.
Cc: qemu-stable@nongnu.org
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit a28fe7dc19)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The address translation logic in get_physical_address() will currently
truncate physical addresses to 32 bits unless long mode is enabled.
This is incorrect when using physical address extensions (PAE) outside
of long mode, with the result that a 32-bit operating system using PAE
to access memory above 4G will experience undefined behaviour.
The truncation code was originally introduced in commit 33dfdb5 ("x86:
only allow real mode to access 32bit without LMA"), where it applied
only to translations performed while paging is disabled (and so cannot
affect guests using PAE).
Commit 9828198 ("target/i386: Add MMU_PHYS_IDX and MMU_NESTED_IDX")
rearranged the code such that the truncation also applied to the use
of MMU_PHYS_IDX and MMU_NESTED_IDX. Commit 4a1e9d4 ("target/i386: Use
atomic operations for pte updates") brought this truncation into scope
for page table entry accesses, and is the first commit for which a
Windows 10 32-bit guest will reliably fail to boot if memory above 4G
is present.
The truncation code however is not completely redundant. Even though the
maximum address size for any executed instruction is 32 bits, helpers for
operations such as BOUND, FSAVE or XSAVE may ask get_physical_address()
to translate an address outside of the 32-bit range, if invoked with an
argument that is close to the 4G boundary. Likewise for processor
accesses, for example TSS or IDT accesses, when EFER.LMA==0.
So, move the address truncation in get_physical_address() so that it
applies to 32-bit MMU indexes, but not to MMU_PHYS_IDX and MMU_NESTED_IDX.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2040
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Cc: qemu-stable@nongnu.org
Co-developed-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit b1661801c1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: drop unrelated change in target/i386/cpu.c)
MSR_VM_HSAVE_PA bits 0-11 are reserved, as are the bits above the
maximum physical address width of the processor. Setting them to
1 causes a #GP (see "15.30.4 VM_HSAVE_PA MSR" in the AMD manual).
The same is true of VMCB addresses passed to VMRUN/VMLOAD/VMSAVE,
even though the manual is not clear on that.
Cc: qemu-stable@nongnu.org
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit d09c79010f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CR3 bits 63:32 are ignored in 32-bit mode (either legacy 2-level
paging or PAE paging). Do this in mmu_translate() to remove
the last where get_physical_address() meaningfully drops the high
bits of the address.
Cc: qemu-stable@nongnu.org
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 68fb78d7d5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The move to decodetree flipped the inequality test for the VEC / VSX
MSR facility check.
This caused application crashes under Linux, where these facility
unavailable interrupts are used for lazy-switching of VEC/VSX register
sets. Getting the incorrect interrupt would result in wrong registers
being loaded, potentially overwriting live values and/or exposing
stale ones.
Cc: qemu-stable@nongnu.org
Reported-by: Joel Stanley <joel@jms.id.au>
Fixes: 70426b5bb7 ("target/ppc: moved stxvx and lxvx from legacy to decodtree")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1769
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Tested-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 2cc0e449d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
MSYS2 is dropping support for 32-bit Windows. This shows up for us
as various packages we were using in our CI job no longer being
available to install, which causes the job to fail. In commit
8e31b744fd we dropped the dependency on libusb and spice, but the
dtc package has also now been removed.
For us as QEMU upstream, "32 bit x86 hosts for system emulation" have
already been deprecated as of QEMU 8.0, so we are ready to drop them
anyway.
Drop the msys2-32bit CI job, as the first step in doing this.
This is cc'd to stable, because this job will also be broken for CI
on the stable branches. We can't drop 32-bit support entirely there,
but we will still be covering at least compilation for 32-bit Windows
via the cross-win32-system job.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240220165602.135695-1-peter.maydell@linaro.org
(cherry picked from commit 5cd3ae4903)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: in 7.2 the piece being removed is different but the job has to go anyway)
Input grab key should be Ctrl-Alt-g, not just Ctrl-Alt.
Fixes: f8d2c9369b ("sdl: use ctrl-alt-g as grab hotkey")
Signed-off-by: Tianlan Zhou <bobby825@126.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 185311130f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Input grab key should be Ctrl-Alt-g, not just Ctrl-Alt.
Fixes: f8d2c9369b ("sdl: use ctrl-alt-g as grab hotkey")
Signed-off-by: Tianlan Zhou <bobby825@126.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 4a20ac400f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It's simply by luck that dbus-display header is built first before the
other units using it.
With sourceset, I can't find an easier way out than declaring an extra
dependency for dbus-display1 generate code.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
(cherry picked from commit 1222070e77)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In `qemu_console_resize()`, the old surface of the console is keeped if the new
console size is the same as the old one. If the old surface is a placeholder,
and the new size of console is the same as the placeholder surface (640*480),
the surface won't be replace.
In this situation, the surface's `QEMU_PLACEHOLDER_FLAG` flag is still set, so
the console won't be displayed in SDL display mode.
This patch fixes this problem by forcing a new surface if the old one is a
placeholder.
Signed-off-by: Tianlan Zhou <bobby825@126.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20240207172024.8-1-bobby825@126.com>
(cherry picked from commit 95b08fee8f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
With VNC, a client can send a non-extended VNC_MSG_CLIENT_CUT_TEXT
message with len=0. In qemu_clipboard_set_data(), the clipboard info
will be updated setting data to NULL (because g_memdup(data, size)
returns NULL when size is 0). If the client does not set the
VNC_ENCODING_CLIPBOARD_EXT feature when setting up the encodings, then
the 'request' callback for the clipboard peer is not initialized.
Later, because data is NULL, qemu_clipboard_request() can be reached
via vdagent_chr_write() and vdagent_clipboard_recv_request() and
there, the clipboard owner's 'request' callback will be attempted to
be called, but that is a NULL pointer.
In particular, this can happen when using the KRDC (22.12.3) VNC
client.
Another scenario leading to the same issue is with two clients (say
noVNC and KRDC):
The noVNC client sets the extension VNC_FEATURE_CLIPBOARD_EXT and
initializes its cbpeer.
The KRDC client does not, but triggers a vnc_client_cut_text() (note
it's not the _ext variant)). There, a new clipboard info with it as
the 'owner' is created and via qemu_clipboard_set_data() is called,
which in turn calls qemu_clipboard_update() with that info.
In qemu_clipboard_update(), the notifier for the noVNC client will be
called, i.e. vnc_clipboard_notify() and also set vs->cbinfo for the
noVNC client. The 'owner' in that clipboard info is the clipboard peer
for the KRDC client, which did not initialize the 'request' function.
That sounds correct to me, it is the owner of that clipboard info.
Then when noVNC sends a VNC_MSG_CLIENT_CUT_TEXT message (it did set
the VNC_FEATURE_CLIPBOARD_EXT feature correctly, so a check for it
passes), that clipboard info is passed to qemu_clipboard_request() and
the original segfault still happens.
Fix the issue by handling updates with size 0 differently. In
particular, mark in the clipboard info that the type is not available.
While at it, switch to g_memdup2(), because g_memdup() is deprecated.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2023-6683
Reported-by: Markus Frank <m.frank@proxmox.com>
Suggested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Markus Frank <m.frank@proxmox.com>
Message-ID: <20240124105749.204610-1-f.ebner@proxmox.com>
(cherry picked from commit 405484b29f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The extended clipboard message protocol requires that the client
activate the extension by requesting a psuedo encoding. If this
is not done, then any extended clipboard messages from the client
should be considered invalid and the client dropped.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20240115095119.654271-1-berrange@redhat.com>
(cherry picked from commit 4cba838896)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CPUID leaf 7 was grouped together with SGX leaf 0x12 by commit
b9edbadefb ("i386: Propagate SGX CPUID sub-leafs to KVM") by mistake.
SGX leaf 0x12 has its specific logic to check if subleaf (starting from 2)
is valid or not by checking the bit 0:3 of corresponding EAX is 1 or
not.
Leaf 7 follows the logic that EAX of subleaf 0 enumerates the maximum
valid subleaf.
Fixes: b9edbadefb ("i386: Propagate SGX CPUID sub-leafs to KVM")
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240125024016.2521244-4-xiaoyao.li@intel.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 0729857c70)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since commit effd60c8 changed how QMP commands are processed, the order
of the block-commit return value and job events in iotests 144 wasn't
fixed and more and caused the test to fail intermittently.
Change the test to cache events first and then print them in a
predefined order.
Waiting three times for JOB_STATUS_CHANGE is a bit uglier than just
waiting for the JOB_STATUS_CHANGE that has "status": "ready", but the
tooling we have doesn't seem to allow the latter easily.
Fixes: effd60c878
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2126
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20240209173103.239994-1-kwolf@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit cc29c12ec6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It doesn't make sense to read the value of MDCR_EL2 on a non-A-profile
CPU, and in fact if you try to do it we will assert:
#6 0x00007ffff4b95e96 in __GI___assert_fail
(assertion=0x5555565a8c70 "!arm_feature(env, ARM_FEATURE_M)", file=0x5555565a6e5c "../../target/arm/helper.c", line=12600, function=0x5555565a9560 <__PRETTY_FUNCTION__.0> "arm_security_space_below_el3") at ./assert/assert.c:101
#7 0x0000555555ebf412 in arm_security_space_below_el3 (env=0x555557bc8190) at ../../target/arm/helper.c:12600
#8 0x0000555555ea6f89 in arm_is_el2_enabled (env=0x555557bc8190) at ../../target/arm/cpu.h:2595
#9 0x0000555555ea942f in arm_mdcr_el2_eff (env=0x555557bc8190) at ../../target/arm/internals.h:1512
We might call pmu_counter_enabled() on an M-profile CPU (for example
from the migration pre/post hooks in machine.c); this should always
return false because these CPUs don't set ARM_FEATURE_PMU.
Avoid the assertion by not calling arm_mdcr_el2_eff() before we
have done the early return for "PMU not present".
This fixes an assertion failure if you try to do a loadvm or
savevm for an M-profile board.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2155
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240208153346.970021-1-peter.maydell@linaro.org
(cherry picked from commit ac1d88e9e7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
_STA will now return 0xB (in common with most other devices)
rather than not setting the bits to indicate this fake device
has not been enabled, and self tests haven't passed.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit b24a981b9f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: rebuild tests/data/acpi/q35/DSDT.cxl for 7.2.x)
Found whilst testing a series for the linux kernel that actually
bothers to check if enabled is set. 0xB is the option used
for vast majority of DSDT entries in QEMU.
It is a little odd for a device that doesn't really exist and
is simply a hook to tell the OS there is a CEDT table but 0xB
seems a reasonable choice and avoids need to special case
this device in the OS.
Means:
* Device present.
* Device enabled and decoding it's resources.
* Not shown in UI
* Functioning properly
* No battery (on this device!)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-12-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit d9ae5802f6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The _STA value returned currently indicates the ACPI0017 device
is not enabled. Whilst this isn't a real device, setting _STA
like this may prevent an OS from enumerating it correctly and
hence from parsing the CEDT table.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-11-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 14ec4ff3e4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
s->iommu_pcibus_by_bus_num is a IOMMUPciBus pointer cache indexed
by bus number, bus number may not always be a fixed value,
i.e., guest reboot to different kernel which set bus number with
different algorithm.
This could lead to endpoint binding to wrong iommu MR in
virtio_iommu_get_endpoint(), then vfio device setup wrong
mapping from other device.
Remove the memset in virtio_iommu_device_realize() to avoid
redundancy with memset in system reset.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240125073706.339369-2-zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 9a457383ce)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu_smbios_type8_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: fd8caa253c ("hw/smbios: support for type 8 (port connector)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 196578c9d0)
qemu_smbios_type11_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: 2d6dcbf93f ("smbios: support setting OEM strings table")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit cd8a35b913)
The latest version of qemu (v8.2.0-869-g7a1dc45af5) crashes when booting
the mcimx7d-sabre emulation with Linux v5.11 and later.
qemu-system-arm: ../system/memory.c:2750: memory_region_set_alias_offset: Assertion `mr->alias' failed.
Problem is that the Designware PCIe emulation accepts the full value range
for the iATU Viewport Register. However, both hardware and emulation only
support four inbound and four outbound viewports.
The Linux kernel determines the number of supported viewports by writing
0xff into the viewport register and reading the value back. The expected
value when reading the register is the highest supported viewport index.
Match that code by masking the supported viewport value range when the
register is written. With this change, the Linux kernel reports
imx6q-pcie 33800000.pcie: iATU: unroll F, 4 ob, 4 ib, align 0K, limit 4G
as expected and supported.
Fixes: d64e5eabc4 ("pci: Add support for Designware IP block")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Nikita Ostrenkov <n.ostrenkov@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240129060055.2616989-1-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 8a73152020)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The -serial option documentation is a bit brief about '-serial none'
and '-serial null'. In particular it's not very clear about the
difference between them, and it doesn't mention that it's up to
the machine model whether '-serial none' means "don't create the
serial port" or "don't wire the serial port up to anything".
Expand on these points.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240122163607.459769-3-peter.maydell@linaro.org
(cherry picked from commit 747bfaf3a9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently if the user passes multiple -serial options on the command
line, we mostly treat those as applying to the different serial
devices in order, so that for example
-serial stdio -serial file:filename
will connect the first serial port to stdio and the second to the
named file.
The exception to this is the '-serial none' serial device type. This
means "don't allocate this serial device", but a bug means that
following -serial options are not correctly handled, so that
-serial none -serial stdio
has the unexpected effect that stdio is connected to the first serial
port, not the second.
This is a very long-standing bug that dates back at least as far as
commit 998bbd74b9 from 2009.
Make the 'none' serial type move forward in the indexing of serial
devices like all the other serial types, so that any subsequent
-serial options are correctly handled.
Note that if your commandline mistakenly had a '-serial none' that
was being overridden by a following '-serial something' option, you
should delete the unnecessary '-serial none'. This will give you the
same behaviour as before, on QEMU versions both with and without this
bug fix.
Cc: qemu-stable@nongnu.org
Reported-by: Bohdan Kostiv <bohdan.kostiv@tii.ae>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240122163607.459769-2-peter.maydell@linaro.org
Fixes: 998bbd74b9 ("default devices: core code & serial lines")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit d2019a9d0c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
With GCC 14 the code failed to compile on i686 (and was wrong for any
version of GCC):
../block/blkio.c: In function ‘blkio_file_open’:
../block/blkio.c:857:28: error: passing argument 3 of ‘blkio_get_uint64’ from incompatible pointer type [-Wincompatible-pointer-types]
857 | &s->mem_region_alignment);
| ^~~~~~~~~~~~~~~~~~~~~~~~
| |
| size_t * {aka unsigned int *}
In file included from ../block/blkio.c:12:
/usr/include/blkio.h:49:67: note: expected ‘uint64_t *’ {aka ‘long long unsigned int *’} but argument is of type ‘size_t *’ {aka ‘unsigned int *’}
49 | int blkio_get_uint64(struct blkio *b, const char *name, uint64_t *value);
| ~~~~~~~~~~^~~~~
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20240130122006.2977938-1-rjones@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 615eaeab3d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The command line options `-ctrl-grab` and `-alt-grab` have been removed
in QEMU 7.1. Instead, use the `-display sdl,grab-mod=<modifiers>` option
to specify the grab modifiers.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2103
Signed-off-by: Yihuan Pan <xun794@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit db101376af)
We're currently allowing the process_incoming_migration_bh bottom-half
to run without holding a reference to the 'current_migration' object,
which leads to a segmentation fault if the BH is still live after
migration_shutdown() has dropped the last reference to
current_migration.
In my system the bug manifests as migrate_multifd() returning true
when it shouldn't and multifd_load_shutdown() calling
multifd_recv_terminate_threads() which crashes due to an uninitialized
multifd_recv_state.
Fix the issue by holding a reference to the object when scheduling the
BH and dropping it before returning from the BH. The same is already
done for the cleanup_bh at migrate_fd_cleanup_schedule().
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1969
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20240119233922.32588-2-farosas@suse.de
Signed-off-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit 27eb8499ed)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
r[id]tlb[01], [iw][id]tlb opcodes use TLB way index passed in a register
by the guest. The host uses 3 bits of the index for ITLB indexing and 4
bits for DTLB, but there's only 7 entries in the ITLB array and 10 in
the DTLB array, so a malicious guest may trigger out-of-bound access to
these arrays.
Change split_tlb_entry_spec return type to bool to indicate whether TLB
way passed to it is valid. Change get_tlb_entry to return NULL in case
invalid TLB way is requested. Add assertion to xtensa_tlb_get_entry that
requested TLB way and entry indices are valid. Add checks to the
[rwi]tlb helpers that requested TLB way is valid and return 0 or do
nothing when it's not.
Cc: qemu-stable@nongnu.org
Fixes: b67ea0cd74 ("target-xtensa: implement memory protection options")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20231215120307.545381-1-jcmvbkbc@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 604927e357)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On a loaded system with --enable-debug, this test can take longer than
5 minutes. Raising the timeout to 6 minutes gives greater headroom for
such situations.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Increase the timeout to 6 minutes for very loaded systems]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-11-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
(cherry picked from commit e8a12fe31f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in tests/qtest/meson.build)
monitor_qmp_dispatcher_co() runs in the iohandler AioContext that is not
polled during nested event loops. The coroutine currently reschedules
itself in the main loop's qemu_aio_context AioContext, which is polled
during nested event loops. One known problem is that QMP device-add
calls drain_call_rcu(), which temporarily drops the BQL, leading to all
sorts of havoc like other vCPU threads re-entering device emulation code
while another vCPU thread is waiting in device emulation code with
aio_poll().
Paolo Bonzini suggested running non-coroutine QMP handlers in the
iohandler AioContext. This avoids trouble with nested event loops. His
original idea was to move coroutine rescheduling to
monitor_qmp_dispatch(), but I resorted to moving it to qmp_dispatch()
because we don't know if the QMP handler needs to run in coroutine
context in monitor_qmp_dispatch(). monitor_qmp_dispatch() would have
been nicer since it's associated with the monitor implementation and not
as general as qmp_dispatch(), which is also used by qemu-ga.
A number of qemu-iotests need updated .out files because the order of
QMP events vs QMP responses has changed.
Solves Issue #1933.
Cc: qemu-stable@nongnu.org
Fixes: 7bed89958b ("device_core: use drain_call_rcu in in qmp_device_add")
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2215192
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2214985
Buglink: https://issues.redhat.com/browse/RHEL-17369
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240118144823.1497953-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit effd60c878)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: omit changes to tests missing in 7.2)
The common.qemu bash functions allow tests to interact with the QMP
monitor of a QEMU process. I spent two days trying to update 141 when
the order of the test output changed, but found it would still fail
occassionally because printf() and QMP events race with synchronous QMP
communication.
I gave up and ported 141 to the existing Python API for QMP tests. The
Python API is less affected by the order in which QEMU prints output
because it does not print all QMP traffic by default.
The next commit changes the order in which QMP messages are received.
Make 141 reliable first.
Cc: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240118144823.1497953-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 9ee2dd4c22)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add a filter function for QMP responses that contain QEMU's
automatically generated node ids. The ids change between runs and must
be masked in the reference output.
The next commit will use this new function.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240118144823.1497953-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit da62b507a2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix in tests/qemu-iotests/iotests.py due to
v7.2.0-939-gbcc6777ad6 "iotests: Filter child node information")
There is a bug in the blklogwrites driver pertaining to logging "write
zeroes" operations, causing log corruption. This can be easily observed
by setting detect-zeroes to something other than "off" for the driver.
The issue is caused by a concurrency bug pertaining to the fact that
"write zeroes" operations have to be logged in two parts: first the log
entry metadata, then the zeroed-out region. While the log entry
metadata is being written by bdrv_co_pwritev(), another operation may
begin in the meanwhile and modify the state of the blklogwrites driver.
This is as intended by the coroutine-driven I/O model in QEMU, of
course.
Unfortunately, this specific scenario is mishandled. A short example:
1. Initially, in the current operation (#1), the current log sector
number in the driver state is only incremented by the number of sectors
taken by the log entry metadata, after which the log entry metadata is
written. The current operation yields.
2. Another operation (#2) may start while the log entry metadata is
being written. It uses the current log position as the start offset for
its log entry. This is in the sector right after the operation #1 log
entry metadata, which is bad!
3. After bdrv_co_pwritev() returns (#1), the current log sector
number is reread from the driver state in order to find out the start
offset for bdrv_co_pwrite_zeroes(). This is an obvious blunder, as the
offset will be the sector right after the (misplaced) operation #2 log
entry, which means that the zeroed-out region begins at the wrong
offset.
4. As a result of the above, the log is corrupt.
Fix this by only reading the driver metadata once, computing the
offsets and sizes in one go (including the optional zeroed-out region)
and setting the log sector number to the appropriate value for the next
operation in line.
Signed-off-by: Ari Sundholm <ari@tuxera.com>
Cc: qemu-stable@nongnu.org
Message-ID: <20240109184646.1128475-1-megari@gmx.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit a9c8ea9547)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When HASH_REPORT is negotiated, the guest_hdr_len might be larger than
the size of the mergeable rx buffer header. Using
virtio_net_hdr_mrg_rxbuf during the header swap might lead a stack
overflow in this case. Fixing this by using virtio_net_hdr_v1_hash
instead.
Reported-by: Xiao Lei <leixiao.nop@zju.edu.cn>
Cc: Yuri Benditovich <yuri.benditovich@daynix.com>
Cc: qemu-stable@nongnu.org
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Fixes: CVE-2023-6693
Fixes: e22f0603fb ("virtio-net: reference implementation of hash report")
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 2220e8189f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Using fleecing backup like in [0] on a qcow2 image (with metadata
preallocation) can lead to the following assertion failure:
> bdrv_co_do_block_status: Assertion `!(ret & BDRV_BLOCK_ZERO)' failed.
In the reproducer [0], it happens because the BDRV_BLOCK_RECURSE flag
will be set by the qcow2 driver, so the caller will recursively check
the file child. Then the BDRV_BLOCK_ZERO set too. Later up the call
chain, in bdrv_co_do_block_status() for the snapshot-access driver,
the assertion failure will happen, because both flags are set.
To fix it, clear the recurse flag after the recursive check was done.
In detail:
> #0 qcow2_co_block_status
Returns 0x45 = BDRV_BLOCK_RECURSE | BDRV_BLOCK_DATA |
BDRV_BLOCK_OFFSET_VALID.
> #1 bdrv_co_do_block_status
Because of the data flag, bdrv_co_do_block_status() will now also set
BDRV_BLOCK_ALLOCATED. Because of the recurse flag,
bdrv_co_do_block_status() for the bdrv_file child will be called,
which returns 0x16 = BDRV_BLOCK_ALLOCATED | BDRV_BLOCK_OFFSET_VALID |
BDRV_BLOCK_ZERO. Now the return value inherits the zero flag.
Returns 0x57 = BDRV_BLOCK_RECURSE | BDRV_BLOCK_DATA |
BDRV_BLOCK_OFFSET_VALID | BDRV_BLOCK_ALLOCATED | BDRV_BLOCK_ZERO.
> #2 bdrv_co_common_block_status_above
> #3 bdrv_co_block_status_above
> #4 bdrv_co_block_status
> #5 cbw_co_snapshot_block_status
> #6 bdrv_co_snapshot_block_status
> #7 snapshot_access_co_block_status
> #8 bdrv_co_do_block_status
Return value is propagated all the way up to here, where the assertion
failure happens, because BDRV_BLOCK_RECURSE and BDRV_BLOCK_ZERO are
both set.
> #9 bdrv_co_common_block_status_above
> #10 bdrv_co_block_status_above
> #11 block_copy_block_status
> #12 block_copy_dirty_clusters
> #13 block_copy_common
> #14 block_copy_async_co_entry
> #15 coroutine_trampoline
[0]:
> #!/bin/bash
> rm /tmp/disk.qcow2
> ./qemu-img create /tmp/disk.qcow2 -o preallocation=metadata -f qcow2 1G
> ./qemu-img create /tmp/fleecing.qcow2 -f qcow2 1G
> ./qemu-img create /tmp/backup.qcow2 -f qcow2 1G
> ./qemu-system-x86_64 --qmp stdio \
> --blockdev qcow2,node-name=node0,file.driver=file,file.filename=/tmp/disk.qcow2 \
> --blockdev qcow2,node-name=node1,file.driver=file,file.filename=/tmp/fleecing.qcow2 \
> --blockdev qcow2,node-name=node2,file.driver=file,file.filename=/tmp/backup.qcow2 \
> <<EOF
> {"execute": "qmp_capabilities"}
> {"execute": "blockdev-add", "arguments": { "driver": "copy-before-write", "file": "node0", "target": "node1", "node-name": "node3" } }
> {"execute": "blockdev-add", "arguments": { "driver": "snapshot-access", "file": "node3", "node-name": "snap0" } }
> {"execute": "blockdev-backup", "arguments": { "device": "snap0", "target": "node1", "sync": "full", "job-id": "backup0" } }
> EOF
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-id: 20240116154839.401030-1-f.ebner@proxmox.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 8a9be79924)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is now expected by rtd so I've expanded using their example as
22.04 is one of our supported platforms. I tried to work out if there
was an easy way to re-generate a requirements.txt from our
pythondeps.toml but in the end went for the easier solution.
Cc: <qemu-stable@nongnu.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231221174200.2693694-1-alex.bennee@linaro.org>
(cherry picked from commit b16a45bc5e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Even though the BLAST command isn't fully implemented in QEMU, the DMA_STAT_BCMBLT
bit should be set after the command has been issued to indicate that the command
has completed.
This fixes an issue with the DC390 DOS driver which issues the BLAST command as
part of its normal error recovery routine at startup, and otherwise sits in a
tight loop waiting for DMA_STAT_BCMBLT to be set before continuing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit c2d7de557d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The setting of DMA_STAT_DONE at the end of a DMA transfer can be configured to
generate an interrupt, however the Linux driver manually checks for DMA_STAT_DONE
being set and if it is, considers that a DMA transfer has completed.
If DMA_STAT_DONE is set but the ESP device isn't indicating an interrupt then
the Linux driver considers this to be a spurious interrupt. However this can
occur in QEMU as there is a delay between the end of DMA transfer where
DMA_STAT_DONE is set, and the ESP device raising its completion interrupt.
This appears to be an incorrect assumption in the Linux driver as the ESP and
PCI DMA interrupt sources are separate (and may not be raised exactly
together), however we can work around this by synchronising the setting of
DMA_STAT_DONE at the end of a DMA transfer with the ESP completion interrupt.
In conjunction with the previous commit Linux is now able to correctly boot
from an am53c974 PCI SCSI device on the hppa C3700 machine without emitting
"iget: checksum invalid" and "Spurious irq, sreg=10" errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 1e8e6644e0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The am53c974/dc390 PCI interrupt has two separate sources: the first is from the
internal ESP device, and the second is from the PCI DMA transfer logic.
Update the ESP interrupt handler so that it sets DMA_STAT_SCSIINT rather than
driving the PCI IRQ directly, and introduce a new esp_pci_update_irq() function
to generate the correct PCI IRQ level. In particular this fixes spurious interrupts
being generated by setting DMA_STAT_DONE at the end of a transfer if DMA_CMD_INTE_D
isn't set in the DMA_CMD register.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 6b41417d93)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup in hw/scsi/esp-pci.c due to v8.0.0-1556-g7d5b0d6864
"bulk: Remove pointless QOM casts")
The current code in esp_pci_dma_memory_rw() sets the DMA address to the value
of the DMA_SPA (Starting Physical Address) register which is incorrect: this
means that for each callback from the SCSI layer the DMA address is set back
to the starting address.
In the case where only a single SCSI callback occurs (currently for transfer
lengths < 128kB) this works fine, however for larger transfers the DMA address
wraps back to the initial starting address, corrupting the buffer holding the
data transferred to the guest.
Fix esp_pci_dma_memory_rw() to use the DMA_WAC (Working Address Counter) for
the DMA address which is correctly incremented across multiple SCSI layer
transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 84a6835e00)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add an update buffer where all block updates are staged.
Flush or discard updates properly, so we should never see
half-completed block writes in pflash storage.
Drop a bunch of FIXME comments ;)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240108160900.104835-4-kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 284a7ee2e2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: drop const in hw/block/pflash_cfi01.c for before
v8.2.0-220-g7d5dc0a367 "hw/block: Constify VMState")
Move the offset calculation, do it once at the start of the function and
let the 'p' variable point directly to the memory location which should
be updated. This makes it simpler to update other buffers than
pfl->storage in an upcoming patch. No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240108160900.104835-2-kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 3b14a555fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For PC-relative translation blocks, env->eip changes during the
execution of a translation block, Therefore, QEMU must be able to
recover an instruction's PC just from the TranslationBlock struct and
the instruction data with. Because a TB will not span two pages, QEMU
stores all the low bits of EIP in the instruction data and replaces them
in x86_restore_state_to_opc. Bits 12 and higher (which may vary between
executions of a PCREL TB, since these only use the physical address in
the hash key) are kept unmodified from env->eip. The assumption is that
these bits of EIP, unlike bits 0-11, will not change as the translation
block executes.
Unfortunately, this is incorrect when the CS base is not aligned to a page.
Then the linear address of the instructions (i.e. the one with the
CS base addred) indeed will never span two pages, but bits 12+ of EIP
can actually change. For example, if CS base is 0x80262200 and EIP =
0x6FF4, the first instruction in the translation block will be at linear
address 0x802691F4. Even a very small TB will cross to EIP = 0x7xxx,
while the linear addresses will remain comfortably within a single page.
The fix is simply to use the low bits of the linear address for data[0],
since those don't change. Then x86_restore_state_to_opc uses tb->cs_base
to compute a temporary linear address (referring to some unknown
instruction in the TB, but with the correct values of bits 12 and higher);
the low bits are replaced with data[0], and EIP is obtained by subtracting
again the CS base.
Huge thanks to Mark Cave-Ayland for the image and initial debugging,
and to Gitlab user @kjliew for help with bisecting another occurrence
of (hopefully!) the same bug.
It should be relatively easy to write a testcase that performs MMIO on
an EIP with different bits 12+ than the first instruction of the translation
block; any help is welcome.
Fixes: e3a79e0e87 ("target/i386: Enable TARGET_TB_PCREL", 2022-10-11)
Cc: qemu-stable@nongnu.org
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Richard Henderson <richard.henderson@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1759
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1964
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2012
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 729ba8e933)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup in target/i386/tcg/tcg-cpu.c target/i386/tcg/translate.c for
v7.2.0-1839-g2e3afe8e19 "target/i386: Replace `TARGET_TB_PCREL` with `CF_PCREL`")
With PCREL, we have a page-relative view of EIP, and an
approximation of PC = EIP+CSBASE that is good enough to
detect page crossings. If we try to recompute PC after
masking EIP, we will mess up that approximation and write
a corrupt value to EIP.
We already handled masking properly for PCREL, so the
fix in b5e0d5d2 was only needed for the !PCREL path.
Cc: qemu-stable@nongnu.org
Fixes: b5e0d5d22f ("target/i386: Fix 32-bit wrapping of pc/eip computation")
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240101230617.129349-1-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit a58506b748)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In 32-bit mode, pc = eip + cs_base is also 32-bit, and must wrap.
Failure to do so results in incorrect memory exceptions to the guest.
Before 732d548732, this was implicitly done via truncation to
target_ulong but only in qemu-system-i386, not qemu-system-x86_64.
To fix this, we must add conditional zero-extensions.
Since we have to test for 32 vs 64-bit anyway, note that cs_base
is always zero in 64-bit mode.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2022
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20231212172510.103305-1-richard.henderson@linaro.org>
(cherry picked from commit b5e0d5d22f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix in target/i386/tcg/tcg-cpu.c for v8.1.0-1190-gb77af26e97
"accel/tcg: Replace CPUState.env_ptr with cpu_env()")
(Mjt: fixup in target/i386/tcg/tcg-cpu.c for v7.2.0-1854-g34a39c2443
"target/i386: Replace `tb_pc()` with `tb->pc`")
j is used while loading an ELF file to byteswap segments'
data. If data is larger than 2GB an overflow may happen.
So j should be elf_word.
This commit fixes a minor bug: it's unlikely anybody is trying to
load ELF files with 2GB+ segments for wrong-endianness targets,
but if they did, it wouldn't work correctly.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: 7ef295ea5b ("loader: Add data swap option to load-elf")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 410c2a4d75)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Sometimes the CI "pages" job fails with a message like this from
htags:
$ htags -anT --tree-view=filetree -m qemu_init -t "Welcome to the QEMU sourcecode"
htags: Negative exec line limit = -371
This is due to a bug in hflags where if the environment is too large it
falls over:
https://lists.gnu.org/archive/html/bug-global/2024-01/msg00000.html
This happens to us because GitLab CI puts the commit message of the
commit under test into the CI_COMMIT_MESSAGE and/or CI_COMMIT_TAG_MESSAGE
environment variables, so the job will fail if the commit happens to
have a verbose commit message.
Work around the htags bug by unsetting these variables while running
htags.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2080
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240111125543.1573473-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 52a21689cd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
LAE should set the access register corresponding to the first operand,
instead, it always modifies access register 1.
Co-developed-by: Ido Plat <Ido.Plat@ibm.com>
Cc: qemu-stable@nongnu.org
Fixes: a1c7610a68 ("target-s390x: implement LAY and LAEY instructions")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240111092328.929421-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e358a25a97)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: target/s390x/tcg/translate.c: fixup for
v8.1.0-1189-gad75a51e84 "tcg: Rename cpu_env to tcg_env" and
v7.2.0-2636-g3ac6f91bca "target/s390x: Drop tcg_temp_free from translate.c")
The hypervisor can deliver (virtual) LPIs to a guest by setting up a
list register to have an intid which is an LPI. The GIC has to treat
these a little differently to standard interrupt IDs, because LPIs
have no Active state, and so the guest will only EOI them, it will
not also deactivate them. So icv_eoir_write() must do two things:
* if the LPI ID is not in any list register, we drop the
priority but do not increment the EOI count
* if the LPI ID is in a list register, we immediately deactivate
it, regardless of the split-drop-and-deactivate control
This can be seen in the VirtualWriteEOIR0() and VirtualWriteEOIR1()
pseudocode in the GICv3 architecture specification.
Without this fix, potentially a hypervisor guest might stall because
LPIs get stuck in a bogus Active+Pending state.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
(cherry picked from commit 82a65e3188)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Current error message:
qemu-system-x86_64: -chardev spice,id=foo: Parameter 'driver' expects an abstract device type
while in fact the meaning is in reverse, -chardev expects
a non-abstract device type.
Fixes: 777357d758 ("chardev: qom-ify" 2016-12-07)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
(cherry picked from commit 4ad87cd4b2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The mcycle/minstret counter's stop flag is mistakenly updated on a copy
on stack. Thus the counter increments even when the CY/IR bit in the
mcountinhibit register is set. This commit corrects its behavior.
Fixes: 3780e33732 (target/riscv: Support mcycle/minstret write operation)
Signed-off-by: Xu Lu <luxu.kernel@bytedance.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 5cb0e7abe1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We have a few test cases that include tests for corner case aspects of
internal snapshots, but nothing that tests that they actually function
as snapshots or that involves deleting a snapshot. Add a test for this
kind of basic internal snapshot functionality.
The error cases include a regression test for the crash we just fixed
with snapshot operations on inactive images.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231201142520.32255-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit bb6e2511eb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, the conflict between -incoming and -loadvm is only detected
when loading the snapshot fails because the image is still inactive for
the incoming migration. This results in a suboptimal error message:
$ ./qemu-system-x86_64 -hda /tmp/test.qcow2 -loadvm foo -incoming defer
qemu-system-x86_64: Device 'ide0-hd0' is writable but does not support snapshots
Catch the situation already in qemu_validate_options() to improve the
message:
$ ./qemu-system-x86_64 -hda /tmp/test.qcow2 -loadvm foo -incoming defer
qemu-system-x86_64: 'incoming' and 'loadvm' options are mutually exclusive
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231201142520.32255-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 5a7f21efaf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
bdrv_is_read_only() only checks if the node is configured to be
read-only eventually, but even if it returns false, writing to the node
may not be permitted at the moment (because it's inactive).
bdrv_is_writable() checks that the node can be written to right now, and
this is what the snapshot operations really need.
Change bdrv_can_snapshot() to use bdrv_is_writable() to fix crashes like
the following:
$ ./qemu-system-x86_64 -hda /tmp/test.qcow2 -loadvm foo -incoming defer
qemu-system-x86_64: ../block/io.c:1990: int bdrv_co_write_req_prepare(BdrvChild *, int64_t, int64_t, BdrvTrackedRequest *, int): Assertion `!(bs->open_flags & BDRV_O_INACTIVE)' failed.
The resulting error message after this patch isn't perfect yet, but at
least it doesn't crash any more:
$ ./qemu-system-x86_64 -hda /tmp/test.qcow2 -loadvm foo -incoming defer
qemu-system-x86_64: Device 'ide0-hd0' is writable but does not support snapshots
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231201142520.32255-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit d3007d348a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
There is no architectural requirement that SME implies SVE, but
our implementation currently assumes it. (FEAT_SME_FA64 does
imply SVE.) So if you try to run a CPU with eg "-cpu max,sve=off"
you quickly run into an assert when the guest tries to write to
SMCR_EL1:
#6 0x00007ffff4b38e96 in __GI___assert_fail
(assertion=0x5555566e69cb "sm", file=0x5555566e5b24 "../../target/arm/helper.c", line=6865, function=0x5555566e82f0 <__PRETTY_FUNCTION__.31> "sve_vqm1_for_el_sm") at ./assert/assert.c:101
#7 0x0000555555ee33aa in sve_vqm1_for_el_sm (env=0x555557d291f0, el=2, sm=false) at ../../target/arm/helper.c:6865
#8 0x0000555555ee3407 in sve_vqm1_for_el (env=0x555557d291f0, el=2) at ../../target/arm/helper.c:6871
#9 0x0000555555ee3724 in smcr_write (env=0x555557d291f0, ri=0x555557da23b0, value=2147483663) at ../../target/arm/helper.c:6995
#10 0x0000555555fd1dba in helper_set_cp_reg64 (env=0x555557d291f0, rip=0x555557da23b0, value=2147483663) at ../../target/arm/tcg/op_helper.c:839
#11 0x00007fff60056781 in code_gen_buffer ()
Avoid this unsupported and slightly odd combination by
disabling SME when SVE is not present.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2005
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231127173318.674758-1-peter.maydell@linaro.org
(cherry picked from commit f7767ca301)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit d921fea338 ("ui/vnc-clipboard: fix infinite loop in
inflate_buffer (CVE-2023-3255)") removed this hunk, but it is still
required, because it can happen that stream.avail_in becomes zero
before coming across a return value of Z_STREAM_END in the loop.
This fixes the host->guest direction of the clipboard with noVNC and
TigerVNC as clients.
Fixes: d921fea338 ("ui/vnc-clipboard: fix infinite loop in inflate_buffer (CVE-2023-3255)")
Reported-by: Friedrich Weber <f.weber@proxmox.com>
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231122125826.228189-1-f.ebner@proxmox.com>
(cherry picked from commit ebfbf39467)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 6f189a08c1 ("ui/gtk-egl: Check EGLSurface before doing
scanout") introduced a regression when QEMU is running with a
virtio-gpu-gl-device on a host under X11. After the guest has
initialized the virtio-gpu-gl-device, the guest screen only
shows "Display output is not active.".
Commit 6f189a08c1 moved all function calls in
gd_egl_scanout_texture() to a code path which is only called
once after gd_egl_init() succeeds in gd_egl_scanout_texture().
Move all function calls in gd_egl_scanout_texture() back to
the regular code path so they get always called if one of the
gd_egl_init() calls was successful.
Fixes: 6f189a08c1 ("ui/gtk-egl: Check EGLSurface before doing scanout")
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231111104020.26183-1-vr_qemu@t-online.de>
(cherry picked from commit 53a939f1bf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The first time gd_egl_scanout_texture() is called, there's a possibility
that the GTK drawing area might not be realized yet, in which case its
associated GdkWindow is NULL. This means gd_egl_init() was also skipped
and the EGLContext and EGLSurface stored in the VirtualGfxConsole are
not valid yet.
Continuing with the scanout in this conditions would result in hitting
an assert in libepoxy: "Couldn't find current GLX or EGL context".
A possible workaround is to just ignore the scanout request, giving the
the GTK drawing area some time to finish its realization. At that point,
the gd_egl_init() will succeed and the EGLContext and EGLSurface stored
in the VirtualGfxConsole will be valid.
Signed-off-by: Antonio Caggiano <quic_acaggian@quicinc.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231016123215.2699269-1-quic_acaggian@quicinc.com>
(cherry picked from commit 6f189a08c1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
erst_realizefn() passes @errp to functions without checking for
failure. If it runs into another failure, it trips error_setv()'s
assertion.
Use the ERRP_GUARD() macro and check *errp, as suggested in commit
ae7c80a7bd ("error: New macro ERRP_GUARD()").
Cc: qemu-stable@nongnu.org
Fixes: f7e26ffa59 ("ACPI ERST: support for ACPI ERST feature")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231120130017.81286-1-philmd@linaro.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 20bc50137f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After a relatively short time, there is an multiplication overflow
when multiplying (now - buft_start) with hda_bytes_per_second().
While the uptime now - buft_start only overflows after 2**63 ns
= 292.27 years, this happens hda_bytes_per_second() times faster
with the multiplication. At 44100 samples/s * 2 channels
* 2 bytes/channel = 176400 bytes/s that is 14.52 hours. After the
multiplication overflow the affected audio stream stalls.
Replace the multiplication and following division with muldiv64()
to prevent a multiplication overflow.
Fixes: 280c1e1cdb ("audio/hda: create millisecond timers that handle IO")
Reported-by: M_O_Bz <m_o_bz@163.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20231105172552.8405-1-vr_qemu@t-online.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 74e8593e7e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Booting a Linux kernel with the malta machine is currently broken
on big endian hosts. The cpu_to_gt32 macro wants to byteswap a value
for little endian targets only, but uses the wrong way to do this:
cpu_to_[lb]e32 works the other way round on big endian hosts! Fix
it by using the same ways on both, big and little endian hosts.
Fixes: 0c8427baf0 ("hw/mips/malta: Use bootloader helper to set BAR registers")
Cc: qemu-stable@nongnu.org
Message-Id: <20230330152613.232082-1-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit dc96009afd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: adjust context for before v7.2.0-677-g0e45355c5c)
If the text description file is larger than DESC_SIZE, we force the last
byte in the buffer to be 0 and write it out.
This results in a corruption.
Try to allocate a big buffer in this case.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1923
Signed-off-by: Fam Zheng <fam@euphon.net>
Message-ID: <20231124115654.3239137-1-fam@euphon.net>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 9fb7b350ba)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixups in block/vmdk.c due to missing-in-7.2 v8.0.0-2084-g28944f99c4
"vmdk: mark more functions as coroutine_fns and GRAPH_RDLOCK")
Commit 0be6bfac62 ("qdev: Implement variable length array properties")
added the DEFINE_PROP_ARRAY() macro with the following comment:
* It is the responsibility of the device deinit code to free the
* @_arrayfield memory.
Commit 9e4aa1fafe added:
DEFINE_PROP_ARRAY("pg0-lock",
XlnxVersalEFuseCtrl, extra_pg0_lock_n16,
extra_pg0_lock_spec, qdev_prop_uint16, uint16_t),
but forgot to free the 'extra_pg0_lock_spec' array. Do it in the
instance_finalize() handler.
Cc: qemu-stable@nongnu.org
Fixes: 9e4aa1fafe ("hw/nvram: Xilinx Versal eFuse device") # v6.2.0+
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231121174051.63038-6-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 4f10c66077)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 0be6bfac62 ("qdev: Implement variable length array properties")
added the DEFINE_PROP_ARRAY() macro with the following comment:
* It is the responsibility of the device deinit code to free the
* @_arrayfield memory.
Commit 68fbcc344e added:
DEFINE_PROP_ARRAY("read-only", XlnxEFuse, ro_bits_cnt, ro_bits,
qdev_prop_uint32, uint32_t),
but forgot to free the 'ro_bits' array. Do it in the instance_finalize
handler.
Cc: qemu-stable@nongnu.org
Fixes: 68fbcc344e ("hw/nvram: Introduce Xilinx eFuse QOM") # v6.2.0+
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231121174051.63038-5-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 49b3e28b7b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 0be6bfac62 ("qdev: Implement variable length array properties")
added the DEFINE_PROP_ARRAY() macro with the following comment:
* It is the responsibility of the device deinit code to free the
* @_arrayfield memory.
Commit 4fb013afcc added:
DEFINE_PROP_ARRAY("oscclk", MPS2SCC, num_oscclk, oscclk_reset,
qdev_prop_uint32, uint32_t),
but forgot to free the 'oscclk_reset' array. Do it in the
instance_finalize() handler.
Cc: qemu-stable@nongnu.org
Fixes: 4fb013afcc ("hw/misc/mps2-scc: Support configurable number of OSCCLK values") # v6.0.0+
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231121174051.63038-4-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 896dd6ff7b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 0be6bfac62 ("qdev: Implement variable length array properties")
added the DEFINE_PROP_ARRAY() macro with the following comment:
* It is the responsibility of the device deinit code to free the
* @_arrayfield memory.
Commit 8077b8e549 added:
DEFINE_PROP_ARRAY("reserved-regions", VirtIOIOMMUPCI,
vdev.nb_reserved_regions, vdev.reserved_regions,
qdev_prop_reserved_region, ReservedRegion),
but forgot to free the 'vdev.reserved_regions' array. Do it in the
instance_finalize() handler.
Cc: qemu-stable@nongnu.org
Fixes: 8077b8e549 ("virtio-iommu-pci: Add array of Interval properties") # v5.1.0+
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20231121174051.63038-3-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit c9a4aa06df)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup hw/virtio/virtio-iommu-pci.c for before v8.1.0-2552-g41cc70cdf5,
"virtio-iommu: Rename reserved_regions into prop_resv_regions" -- so now
patch subject matches actual change again)
The syndrome register value always has an IL field at bit 25, which
is 0 for a trap on a 16 bit instruction, and 1 for a trap on a 32
bit instruction (or for exceptions which aren't traps on a known
instruction, like PC alignment faults). This means that our
syn_*() functions should always either take an is_16bit argument to
determine whether to set the IL bit, or else unconditionally set it.
We missed setting the IL bit for the syndrome for three kinds of trap:
* an SVE access exception
* a pointer authentication check failure
* a BTI (branch target identification) check failure
All of these traps are AArch64 only, and so the instruction causing
the trap is always 64 bit. This means we can unconditionally set
the IL bit in the syn_*() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231120150121.3458408-1-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 11a3c4a286)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
This implementation follows what bottom half does, but it does not add
a tracepoint for the case that the network device backend started
delivering a packet to a device which is already engaging in I/O. This
is because such reentrancy frequently happens for
qemu_flush_queued_packets() and is insignificant.
Fixes: CVE-2023-3019
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 9050f976e4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
In preparation for such a change, add MemReentrancyGuard * as a
parameter of qemu_new_nic().
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 7d0fefdf81)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: fixup in hw/net/xen_nic.c due to lack of v8.1.0-2771-g25967ff69f
"hw/xen: update Xen PV NIC to XenDevice model"
and removed hw/net/igb.c bits)
Legacy software contains a standard mechanism for generating a reset to a
Serial ATA device - setting the SRST (software reset) bit in the Device
Control register.
Serial ATA has a more robust mechanism called COMRESET, also referred to
as port reset. A port reset is the preferred mechanism for error
recovery and should be used in place of software reset.
Commit e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
(mjt: 1e5ad6b06b in stable-7.2 series, v7.2.6)
improved the handling of PxCI, such that PxCI gets cleared after handling
a non-NCQ, or NCQ command (instead of incorrectly clearing PxCI after
receiving anything - even a FIS that failed to parse, which should NOT
clear PxCI, so that you can see which command slot that caused an error).
However, simply clearing PxCI after a non-NCQ, or NCQ command, is not
enough, we also need to clear PxCI when receiving a SRST in the Device
Control register.
A legacy software reset is performed by the host sending two H2D FISes,
the first H2D FIS asserts SRST, and the second H2D FIS deasserts SRST.
The first H2D FIS will not get a D2H reply, and requires the FIS to have
the C bit set to one, such that the HBA itself will clear the bit in PxCI.
The second H2D FIS will get a D2H reply once the diagnostic is completed.
The clearing of the bit in PxCI for this command should ideally be done
in ahci_init_d2h() (if it was a legacy software reset that caused the
reset (a COMRESET does not use a command slot)). However, since the reset
value for PxCI is 0, modify ahci_reset_port() to actually clear PxCI to 0,
that way we can avoid complex logic in ahci_init_d2h().
This fixes an issue for FreeBSD where the device would fail to reset.
The problem was not noticed in Linux, because Linux uses a COMRESET
instead of a legacy software reset by default.
Fixes: e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-ID: <20231108222657.117984-1-nks@flawful.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit eabb921250)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: mention 1e5ad6b06b for stable-7.2)
LAALG uses op_laa() and wout_addu64(). The latter expects cc_src to be
set, but the former does not do it. This can lead to assertion failures
if something sets cc_src to neither 0 nor 1 before.
Fix by introducing op_laa_addu64(), which sets cc_src, and using it for
LAALG.
Fixes: 4dba4d6fef ("target/s390x: Use atomic operations for LOAD AND OP")
Cc: qemu-stable@nongnu.org
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231106093605.1349201-4-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit bea402482a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Before commit "hw/ide: reset: cancel async DMA operation before
resetting state", this test would fail, because a reset with a
pending write operation would lead to an unsolicited write to the
first sector of the disk.
The test writes a pattern to the beginning of the disk and verifies
that it is still intact after a reset with a pending operation. It
also checks that the pending operation actually completes correctly.
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Message-ID: <20230906130922.142845-2-f.ebner@proxmox.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit cc610857bb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If there is a pending DMA operation during ide_bus_reset(), the fact
that the IDEState is already reset before the operation is canceled
can be problematic. In particular, ide_dma_cb() might be called and
then use the reset IDEState which contains the signature after the
reset. When used to construct the IO operation this leads to
ide_get_sector() returning 0 and nsector being 1. This is particularly
bad, because a write command will thus destroy the first sector which
often contains a partition table or similar.
Traces showing the unsolicited write happening with IDEState
0x5595af6949d0 being used after reset:
> ahci_port_write ahci(0x5595af6923f0)[0]: port write [reg:PxSCTL] @ 0x2c: 0x00000300
> ahci_reset_port ahci(0x5595af6923f0)[0]: reset port
> ide_reset IDEstate 0x5595af6949d0
> ide_reset IDEstate 0x5595af694da8
> ide_bus_reset_aio aio_cancel
> dma_aio_cancel dbs=0x7f64600089a0
> dma_blk_cb dbs=0x7f64600089a0 ret=0
> dma_complete dbs=0x7f64600089a0 ret=0 cb=0x5595acd40b30
> ahci_populate_sglist ahci(0x5595af6923f0)[0]
> ahci_dma_prepare_buf ahci(0x5595af6923f0)[0]: prepare buf limit=512 prepared=512
> ide_dma_cb IDEState 0x5595af6949d0; sector_num=0 n=1 cmd=DMA WRITE
> dma_blk_io dbs=0x7f6420802010 bs=0x5595ae2c6c30 offset=0 to_dev=1
> dma_blk_cb dbs=0x7f6420802010 ret=0
> (gdb) p *qiov
> $11 = {iov = 0x7f647c76d840, niov = 1, {{nalloc = 1, local_iov = {iov_base = 0x0,
> iov_len = 512}}, {__pad = "\001\000\000\000\000\000\000\000\000\000\000",
> size = 512}}}
> (gdb) bt
> #0 blk_aio_pwritev (blk=0x5595ae2c6c30, offset=0, qiov=0x7f6420802070, flags=0,
> cb=0x5595ace6f0b0 <dma_blk_cb>, opaque=0x7f6420802010)
> at ../block/block-backend.c:1682
> #1 0x00005595ace6f185 in dma_blk_cb (opaque=0x7f6420802010, ret=<optimized out>)
> at ../softmmu/dma-helpers.c:179
> #2 0x00005595ace6f778 in dma_blk_io (ctx=0x5595ae0609f0,
> sg=sg@entry=0x5595af694d00, offset=offset@entry=0, align=align@entry=512,
> io_func=io_func@entry=0x5595ace6ee30 <dma_blk_write_io_func>,
> io_func_opaque=io_func_opaque@entry=0x5595ae2c6c30,
> cb=0x5595acd40b30 <ide_dma_cb>, opaque=0x5595af6949d0,
> dir=DMA_DIRECTION_TO_DEVICE) at ../softmmu/dma-helpers.c:244
> #3 0x00005595ace6f90a in dma_blk_write (blk=0x5595ae2c6c30,
> sg=sg@entry=0x5595af694d00, offset=offset@entry=0, align=align@entry=512,
> cb=cb@entry=0x5595acd40b30 <ide_dma_cb>, opaque=opaque@entry=0x5595af6949d0)
> at ../softmmu/dma-helpers.c:280
> #4 0x00005595acd40e18 in ide_dma_cb (opaque=0x5595af6949d0, ret=<optimized out>)
> at ../hw/ide/core.c:953
> #5 0x00005595ace6f319 in dma_complete (ret=0, dbs=0x7f64600089a0)
> at ../softmmu/dma-helpers.c:107
> #6 dma_blk_cb (opaque=0x7f64600089a0, ret=0) at ../softmmu/dma-helpers.c:127
> #7 0x00005595ad12227d in blk_aio_complete (acb=0x7f6460005b10)
> at ../block/block-backend.c:1527
> #8 blk_aio_complete (acb=0x7f6460005b10) at ../block/block-backend.c:1524
> #9 blk_aio_write_entry (opaque=0x7f6460005b10) at ../block/block-backend.c:1594
> #10 0x00005595ad258cfb in coroutine_trampoline (i0=<optimized out>,
> i1=<optimized out>) at ../util/coroutine-ucontext.c:177
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: simon.rowe@nutanix.com
Message-ID: <20230906130922.142845-1-f.ebner@proxmox.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 7d7512019f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In a two-stage translation, the result of the BTI guarded bit should
be the guarded bit from the first stage of translation, as there is
no BTI guard information in stage two. Our code tried to do this,
but got it wrong, because we currently have two fields where the GP
bit information might live (ARMCacheAttrs::guarded and
CPUTLBEntryFull::extra::arm::guarded), and we were storing the GP bit
in the latter during the stage 1 walk but trying to copy the former
in combine_cacheattrs().
Remove the duplicated storage, and always use the field in
CPUTLBEntryFull; correctly propagate the stage 1 value to the output
in get_phys_addr_twostage().
Note for stable backports: in v8.0 and earlier the field is named
result->f.guarded, not result->f.extra.arm.guarded.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1950
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231031173723.26582-1-peter.maydell@linaro.org
(cherry picked from commit 4c09abeae8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: replace f.extra.arm.guarded -> f.guarded due to v8.1.0-1179-ga81fef4b64)
We currently don't correctly handle the VSTCR_EL2.SW and VTCR_EL2.NSW
configuration bits. These allow configuration of whether the stage 2
page table walks for Secure IPA and NonSecure IPA should do their
descriptor reads from Secure or NonSecure physical addresses. (This
is separate from how the translation table base address and other
parameters are set: an NS IPA always uses VTTBR_EL2 and VTCR_EL2
for its base address and walk parameters, regardless of the NSW bit,
and similarly for Secure.)
Provide a new function ptw_idx_for_stage_2() which returns the
MMU index to use for descriptor reads, and use it to set up
the .in_ptw_idx wherever we call get_phys_addr_lpae().
For a stage 2 walk, wherever we call get_phys_addr_lpae():
* .in_ptw_idx should be ptw_idx_for_stage_2() of the .in_mmu_idx
* .in_secure should be true if .in_mmu_idx is Stage2_S
This allows us to correct S1_ptw_translate() so that it consistently
always sets its (out_secure, out_phys) to the result it gets from the
S2 walk (either by calling get_phys_addr_lpae() or by TLB lookup).
This makes better conceptual sense because the S2 walk should return
us an (address space, address) tuple, not an address that we then
randomly assign to S or NS.
Our previous handling of SW and NSW was broken, so guest code
trying to use these bits to put the s2 page tables in the "other"
address space wouldn't work correctly.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1600
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230504135425.2748672-3-peter.maydell@linaro.org
(cherry picked from commit fcc0b0418f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Bit 63 in a Table descriptor is only the NSTable bit for stage 1
translations; in stage 2 it is RES0. We were incorrectly looking at
it all the time.
This causes problems if:
* the stage 2 table descriptor was incorrectly setting the RES0 bit
* we are doing a stage 2 translation in Secure address space for
a NonSecure stage 1 regime -- in this case we would incorrectly
do an immediate downgrade to NonSecure
A bug elsewhere in the code currently prevents us from getting
to the second situation, but when we fix that it will be possible.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230504135425.2748672-2-peter.maydell@linaro.org
(cherry picked from commit 21a4ab8318)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When TCG is disabled this part of the code should not be reachable, so
wrap it with an ifdef for now.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 0d3de77a07)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: trivial change which makes two subsequent cherry-picks to apply cleanly)
In case when we're rebasing within one backing chain, and when target image
is larger than old backing file, bdrv_is_allocated_above() ends up setting
*pnum = 0. As a result, target offset isn't getting incremented, and we
get stuck in an infinite for loop. Let's detect this case and proceed
further down the loop body, as the offsets beyond the old backing size need
to be explicitly zeroed.
Signed-off-by: Andrey Drobyshev <andrey.drobyshev@virtuozzo.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20230919165804.439110-2-andrey.drobyshev@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 8b097fd6b0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A build of GCC 13.2 will have stack protector enabled by default if it
was configured with --enable-default-ssp option. For such a compiler,
it is necessary to explicitly disable stack protector when linking
without standard libraries.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230731091042.139159-2-akihiko.odaki@daynix.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 7a06a8fec9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Block Size Register bits [14:12] is SDMA Buffer Boundary, it is missed
in register write, but it is needed in SDMA transfer. e.g. it will be
used in sdhci_sdma_transfer_multi_blocks to calculate boundary_ variables.
Missing this field will cause wrong operation for different SDMA Buffer
Boundary settings.
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Fixes: dfba99f17f ("hw/sdhci: Fix DMA Transfer Block Size field")
Signed-off-by: Lu Gao <lu.gao@verisilicon.com>
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-ID: <20220321055618.4026-1-lu.gao@verisilicon.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit ae5f70baf5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Those PS/2 ports are created with the LASI controller when
a 32-bit PA-RISC machine is created.
Mark them not user-createable to avoid showing them in
the qemu device list.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
(cherry picked from commit a1e6a5c462)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
sh4 uses gUSA (general UserSpace Atomicity) to provide atomicity on CPUs
that don't have atomic instructions. A gUSA region that adds 1 to an
atomic variable stored in @R2 looks like this:
4004b6: 03 c7 mova 4004c4 <gusa+0x10>,r0
4004b8: f3 61 mov r15,r1
4004ba: 09 00 nop
4004bc: fa ef mov #-6,r15
4004be: 22 63 mov.l @r2,r3
4004c0: 01 73 add #1,r3
4004c2: 32 22 mov.l r3,@r2
4004c4: 13 6f mov r1,r15
R0 contains a pointer to the end of the gUSA region
R1 contains the saved stack pointer
R15 contains negative length of the gUSA region
When this region is interrupted by a signal, the kernel detects if
R15 >= -128U. If yes, the kernel rolls back PC to the beginning of the
region and restores SP by copying R1 to R15.
The problem happens if we are interrupted by a signal at address 4004c4.
R15 still holds the value -6, but the atomic value was already written by
an instruction at address 4004c2. In this situation we can't undo the
gUSA. The function unwind_gusa does nothing, the signal handler attempts
to push a signal frame to the address -6 and crashes.
This patch fixes it, so that if we are interrupted at the last instruction
in a gUSA region, we copy R1 to R15 to restore the correct stack pointer
and avoid crashing.
There's another bug: if we are interrupted in a delay slot, we save the
address of the instruction in the delay slot. We must save the address of
the previous instruction.
Cc: qemu-stable@nongnu.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Yoshinori Sato <ysato@users.sourcefoege.jp>
Message-Id: <b16389f7-6c62-70b7-59b3-87533c0bcc@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 3b894b699c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The migration code uses unsigned values for 16, 32 and 64-bit
operations. Fix the script to do the same.
This was causing an issue when parsing the migration stream generated
on the ppc64 target because one of instance_ids was larger than the
32bit signed maximum:
Traceback (most recent call last):
File "/home/fabiano/kvm/qemu/build/scripts/analyze-migration.py", line 658, in <module>
dump.read(dump_memory = args.memory)
File "/home/fabiano/kvm/qemu/build/scripts/analyze-migration.py", line 592, in read
classdesc = self.section_classes[section_key]
KeyError: ('spapr_iommu', -2147483648)
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231009184326.15777-6-farosas@suse.de>
(cherry picked from commit caea03279e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Guest driver allocates and initialize page tables to be used as a ring
of descriptors for CQ and async events.
The page table that represents the ring, along with the number of pages
in the page table is passed to the device.
Currently our device supports only one page table for a ring.
Let's make sure that the number of page table entries the driver
reports, do not exceeds the one page table size.
Reported-by: Soul Chen <soulchen8650@gmail.com>
Signed-off-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Fixes: CVE-2023-1544
Message-ID: <20230301142926.18686-1-yuval.shaia.ml@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 85fc35afa9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reset the current sample counter when writing the Channel Sample
Count Register. The Linux ens1370 driver and the AROS sb128
driver expect the current sample counter counts down from sample
count to 0 after a write to the Channel Sample Count Register.
Currently the current sample counter starts from 0 after a reset
or the last count when the counter was stopped.
The current sample counter is used to raise an interrupt whenever
a complete buffer was transferred. When the counter starts with a
value lower than the reload value, the interrupt triggeres before
the buffer was completly transferred. This may lead to corrupted
audio streams.
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20230917065813.6692-1-vr_qemu@t-online.de>
(cherry picked from commit 00e3b29d06)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU will crash if anyone tries to set tls-authz (which is a type
StrOrNull) with 'null' value. Fix it in the easy way by converting it to
qstring just like the other two tls parameters.
Cc: qemu-stable@nongnu.org # v4.0+
Fixes: d2f1d29b95 ("migration: add support for a "tls-authz" migration parameter")
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20230905162335.235619-2-peterx@redhat.com>
(cherry picked from commit 86dec715a7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: the function is in m/migration.c, not m/option.c; minor context tweak)
An MSI from I/O APIC may not exactly equal to APIC_DEFAULT_ADDRESS. In
fact, Windows 17763.3650 configures I/O APIC to set the dest_mode bit.
Cover the range assigned to APIC.
Fixes: 577c470f43 ("x86_iommu/amd: Prepare for interrupt remap support")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230921114612.40671-1-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 0114c45130)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use abi_ullong not uint64_t so that the alignment of the field
and therefore the layout of the struct is correct.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 33bc4fa78b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When starting a guest via libvirt with "virsh start --console ...",
the first second of the console output is missing. This is especially
annoying on s390x that only has a text console by default and no graphical
output - if the bios fails to boot here, the information about what went
wrong is completely lost.
One part of the problem (there is also some things to be done on the
libvirt side) is that QEMU only checks with a 1 second timer whether
the other side of the pty is already connected, so the first second of
the console output is always lost.
This likely used to work better in the past, since the code once checked
for a re-connection during write, but this has been removed in commit
f8278c7d74 ("char-pty: remove the check for connection on write") to avoid
some locking.
To ease the situation here at least a little bit, let's check with g_poll()
whether we could send out the data anyway, even if the connection has not
been marked as "connected" yet. The file descriptor is marked as non-blocking
anyway since commit fac6688a18 ("Do not hang on full PTY"), so this should
not cause any trouble if the other side is not ready for receiving yet.
With this patch applied, I can now successfully see the bios output of
a s390x guest when running it with "virsh start --console" (with a patched
version of virsh that fixes the remaining issues there, too).
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230816210743.1319018-1-thuth@redhat.com>
(cherry picked from commit 4f7689f081)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: use TFR() instead of RETRY_ON_EINTR() before v7.2.0-538-g8b6aa69365)
The fw_cfg DMA write callback in ramfb prepares a new display surface in
QEMU; this new surface is put to use ("swapped in") upon the next display
update. At that time, the old surface (if any) is released.
If the guest triggers the fw_cfg DMA write callback at least twice between
two adjacent display updates, then the second callback (and further such
callbacks) will leak the previously prepared (but not yet swapped in)
display surface.
The issue can be shown by:
(1) starting QEMU with "-trace displaysurface_free", and
(2) running the following program in the guest UEFI shell:
> #include <Library/ShellCEntryLib.h> // ShellAppMain()
> #include <Library/UefiBootServicesTableLib.h> // gBS
> #include <Protocol/GraphicsOutput.h> // EFI_GRAPHICS_OUTPUT_PROTOCOL
>
> INTN
> EFIAPI
> ShellAppMain (
> IN UINTN Argc,
> IN CHAR16 **Argv
> )
> {
> EFI_STATUS Status;
> VOID *Interface;
> EFI_GRAPHICS_OUTPUT_PROTOCOL *Gop;
> UINT32 Mode;
>
> Status = gBS->LocateProtocol (
> &gEfiGraphicsOutputProtocolGuid,
> NULL,
> &Interface
> );
> if (EFI_ERROR (Status)) {
> return 1;
> }
>
> Gop = Interface;
>
> Mode = 1;
> for ( ; ;) {
> Status = Gop->SetMode (Gop, Mode);
> if (EFI_ERROR (Status)) {
> break;
> }
>
> Mode = 1 - Mode;
> }
>
> return 1;
> }
The symptom is then that:
- only one trace message appears periodically,
- the time between adjacent messages keeps increasing -- implying that
some list structure (containing the leaked resources) keeps growing,
- the "surface" pointer is ever different.
> 18566@1695127471.449586:displaysurface_free surface=0x7f2fcc09a7c0
> 18566@1695127471.529559:displaysurface_free surface=0x7f2fcc9dac10
> 18566@1695127471.659812:displaysurface_free surface=0x7f2fcc441dd0
> 18566@1695127471.839669:displaysurface_free surface=0x7f2fcc0363d0
> 18566@1695127472.069674:displaysurface_free surface=0x7f2fcc413a80
> 18566@1695127472.349580:displaysurface_free surface=0x7f2fcc09cd00
> 18566@1695127472.679783:displaysurface_free surface=0x7f2fcc1395f0
> 18566@1695127473.059848:displaysurface_free surface=0x7f2fcc1cae50
> 18566@1695127473.489724:displaysurface_free surface=0x7f2fcc42fc50
> 18566@1695127473.969791:displaysurface_free surface=0x7f2fcc45dcc0
> 18566@1695127474.499708:displaysurface_free surface=0x7f2fcc70b9d0
> 18566@1695127475.079769:displaysurface_free surface=0x7f2fcc82acc0
> 18566@1695127475.709941:displaysurface_free surface=0x7f2fcc369c00
> 18566@1695127476.389619:displaysurface_free surface=0x7f2fcc32b910
> 18566@1695127477.119772:displaysurface_free surface=0x7f2fcc0d5a20
> 18566@1695127477.899517:displaysurface_free surface=0x7f2fcc086c40
> 18566@1695127478.729962:displaysurface_free surface=0x7f2fccc72020
> 18566@1695127479.609839:displaysurface_free surface=0x7f2fcc185160
> 18566@1695127480.539688:displaysurface_free surface=0x7f2fcc23a7e0
> 18566@1695127481.519759:displaysurface_free surface=0x7f2fcc3ec870
> 18566@1695127482.549930:displaysurface_free surface=0x7f2fcc634960
> 18566@1695127483.629661:displaysurface_free surface=0x7f2fcc26b140
> 18566@1695127484.759987:displaysurface_free surface=0x7f2fcc321700
> 18566@1695127485.940289:displaysurface_free surface=0x7f2fccaad100
We figured this wasn't a CVE-worthy problem, as only small amounts of
memory were leaked (the framebuffer itself is mapped from guest RAM, QEMU
only allocates administrative structures), plus libvirt restricts QEMU
memory footprint anyway, thus the guest can only DoS itself.
Plug the leak, by releasing the last prepared (not yet swapped in) display
surface, if any, in the fw_cfg DMA write callback.
Regarding the "reproducer", with the fix in place, the log is flooded with
trace messages (one per fw_cfg write), *and* the trace message alternates
between just two "surface" pointer values (i.e., nothing is leaked, the
allocator flip-flops between two objects in effect).
This issue appears to date back to the introducion of ramfb (995b30179b,
"hw/display: add ramfb, a simple boot framebuffer living in guest ram",
2018-06-18).
Cc: Gerd Hoffmann <kraxel@redhat.com> (maintainer:ramfb)
Cc: qemu-stable@nongnu.org
Fixes: 995b30179b
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230919131955.27223-1-lersek@redhat.com>
(cherry picked from commit e0288a7784)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CVTPS2PD only loads a half-register for memory, unlike the other
operations under 0x0F 0x5A. "Unpack" the group into separate
emission functions instead of using gen_unary_fp_sse.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit abd41884c5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CVTPS2PD only loads a half-register for memory, like CVTPH2PS. It can
reuse the "ph" packed half-precision size to load a half-register,
but rename it to "xh" because it is now a variation of "x" (it is not
used only for half-precision values).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit a48b26978a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Before this change, MOVNTPS and MOVNTPD were labeled as Exception Class
4 (only requiring alignment for legacy SSE instructions). This changes
them to Exception Class 1 (always requiring memory alignment), as
documented in the Intel manual.
Message-Id: <20230501111428.95998-3-ricky@rzhou.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 8bf171c2d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix the exception classes for some SSE/AVX instructions to match what is
documented in the Intel manual.
These changes are expected to have no functional effect on the behavior
that qemu implements (primarily >= 16-byte memory alignment checks). For
instance, since qemu does not implement the AC flag, there is no
difference in behavior between Exception Classes 4 and 5 for
instructions where the SSE version only takes <16 byte memory operands.
Message-Id: <20230501111428.95998-2-ricky@rzhou.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit cab529b0dc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Adds some comments describing what instructions correspond to decoding
table entries and fixes some existing comments which named the wrong
instruction.
Message-Id: <20230501111428.95998-1-ricky@rzhou.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit afa94dabc5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The instructions also use bits 3 and 7 of their 8-byte immediate.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 9e65829699)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
VRCPSS, VRSQRTSS and VCVTSx2Sx have a 32-bit or 64-bit memory operand,
which is represented in the decoding tables by X86_VEX_REPScalar. Add it
to the tables, and make validate_vex() handle the case of an instruction
that is in exception type 4 without the REP prefix and exception type 5
with it; this is the cas of VRCP and VRSQRT.
Reported-by: yongwoo <https://gitlab.com/yongwoo36>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1377
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 3d304620ec)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Otherwise when a FORMAT UNIT command is issued, the SCSI layer can become
confused because it can find itself in the situation where it thinks there
is still data to be transferred which can cause the next emulated SCSI
command to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 6ab71761 ("scsi-disk: add FORMAT UNIT command")
Tested-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230913204410.65650-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit be2b619a17)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the case where a SCSI layer transfer is incorrectly terminated, it is
possible for a TI command to cause a SCSI buffer overflow due to the
expected transfer data length being less than the available data in the
FIFO. When this occurs the unsigned async_len variable underflows and
becomes a large offset which writes past the end of the allocated SCSI
buffer.
Restrict the non-DMA transfer length to be the smallest of the expected
transfer length and the available FIFO data to ensure that it is no longer
possible for the SCSI buffer overflow to occur.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1810
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230913204410.65650-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 77668e4b9b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The call to esp_dma_enable() was being made with the SYSBUS_ESP type instead of
the ESP type. This meant that when GPIO 1 was being used to trigger a DMA
request from an external DMA controller, the setting of ESPState's dma_enabled
field would clobber unknown memory whilst the dma_cb callback pointer would
typically return NULL so the DMA request would never start.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230913204410.65650-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit b86dc5cb0b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Our linker script for optionroms specifies only the placement of the
.text section, leaving the linker free to place the remaining sections
at arbitrary places in the file.
Since at least binutils 2.39, the .note.gnu.build-id section is now
being placed at the start of the file, which causes label addresses to
be shifted. For linuxboot_dma.bin that means that the PnP header
(among others) will not be found when determining the type of ROM at
optionrom_setup():
(0x1c is the label _pnph, where the magic "PnP" is)
$ xxd /usr/share/qemu/linuxboot_dma.bin | grep "PnP"
00000010: 0000 0000 0000 0000 0000 1c00 2450 6e50 ............$PnP
$ xxd pc-bios/optionrom/linuxboot_dma.bin | grep "PnP"
00000010: 0000 0000 0000 0000 0000 4c00 2450 6e50 ............$PnP
^bad
Using a freshly built linuxboot_dma.bin ROM results in a broken boot:
SeaBIOS (version rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org)
Booting from Hard Disk...
Boot failed: could not read the boot disk
Booting from Floppy...
Boot failed: could not read the boot disk
No bootable device.
We're not using the build-id section, so pass the --build-id=none
option to the linker to remove it entirely.
Note: In theory, this same issue could happen with any other
section. The ideal solution would be to have all unused sections
discarded in the linker script. However that would be a larger change,
specially for the pvh rom which uses the .bss and COMMON sections so
I'm addressing only the immediate issue here.
Reported-by: Vasiliy Ulyanov <vulyanov@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230926192502.15986-1-farosas@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 35ed01ba54)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(mjt: remove unrelated stable@vger)
VNC_FEATURE_XVP was not shifted left before adding it to vs->features,
so it was never enabled; but it was also checked the wrong way with
a logical AND instead of vnc_has_feature. Fix both places.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 477b301000)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The debug message was cut and pasted from the invalid audio format
case, but the audio message is at bytes 2-3.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 0cb9c5880e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We are doing things like
nb_sectors /= (s->qdev.blocksize / BDRV_SECTOR_SIZE);
in the code here (e.g. in scsi_disk_emulate_mode_sense()), so if
the blocksize is smaller than BDRV_SECTOR_SIZE (=512), this crashes
with a division by 0 exception. Thus disallow block sizes of 256
bytes to avoid this situation.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1813
CVE: 2023-42467
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230925091854.49198-1-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 7cfcc79b0a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
mttcg asserts that an execution ending with EXCP_HALTED must have
cpu->halted. However between the event or instruction that sets
cpu->halted and requests exit and the assertion here, an
asynchronous event could clear cpu->halted.
This leads to crashes running AIX on ppc/pseries because it uses
H_CEDE/H_PROD hcalls, where H_CEDE sets self->halted = 1 and
H_PROD sets other cpu->halted = 0 and kicks it.
H_PROD could be turned into an interrupt to wake, but several other
places in ppc, sparc, and semihosting follow what looks like a similar
pattern setting halted = 0 directly. So remove this assertion.
Reported-by: Ivan Warren <ivan@vmfacility.fr>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230829010658.8252-1-npiggin@gmail.com>
[rth: Keep the case label and adjust the comment.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 0e5903436d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The LDRT/STRT "unprivileged load/store" instructions behave like
normal ones if executed at EL0. We handle this correctly for
the load/store semantics, but get the MTE checking wrong.
We always look at s->mte_active[is_unpriv] to see whether we should
be doing MTE checks, but in hflags.c when we set the TB flags that
will be used to fill the mte_active[] array we only set the
MTE0_ACTIVE bit if UNPRIV is true (i.e. we are not at EL0).
This means that a LDRT at EL0 will see s->mte_active[1] as 0,
and will not do MTE checks even when MTE is enabled.
To avoid the translate-time code having to do an explicit check on
s->unpriv to see if it is OK to index into the mte_active[] array,
duplicate MTE_ACTIVE into MTE0_ACTIVE when UNPRIV is false.
(This isn't a very serious bug because generally nobody executes
LDRT/STRT at EL0, because they have no use there.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230912140434.1333369-2-peter.maydell@linaro.org
(cherry picked from commit 903dbefc2b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: before v7.2.0-1636-g671efad16a this code was in target/arm/helper.c)
qemu-hppa may crash when delivering a signal. It can be demonstrated with
this program. Compile the program with "hppa-linux-gnu-gcc -O2 signal.c"
and run it with "qemu-hppa -one-insn-per-tb a.out". It reports that the
address of the flag is 0xb4 and it crashes when attempting to touch it.
#include <stdio.h>
#include <stdlib.h>
#include <sys/time.h>
#include <signal.h>
sig_atomic_t flag;
void sig(int n)
{
printf("&flag: %p\n", &flag);
flag = 1;
}
int main(void)
{
struct sigaction sa;
struct itimerval it;
sa.sa_handler = sig;
sigemptyset(&sa.sa_mask);
sa.sa_flags = SA_RESTART;
if (sigaction(SIGALRM, &sa, NULL)) perror("sigaction"), exit(1);
it.it_interval.tv_sec = 0;
it.it_interval.tv_usec = 100;
it.it_value.tv_sec = it.it_interval.tv_sec;
it.it_value.tv_usec = it.it_interval.tv_usec;
if (setitimer(ITIMER_REAL, &it, NULL)) perror("setitimer"), exit(1);
while (1) {
}
}
The reason for the crash is that the signal handling routine doesn't clear
the 'N' flag in the PSW. If the signal interrupts a thread when the 'N'
flag is set, the flag remains set at the beginning of the signal handler
and the first instruction of the signal handler is skipped.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit 2529497cb6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When writing a value to the decrementer that raises an exception, the
irq is raised, but the value is not stored so the store doesn't appear
to have changed the register when it is read again.
Always store the write value to the register.
Fixes: e81a982aa5 ("PPC: Clean up DECR implementation")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit febb71d543)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The decrementer store function has logic that short-cuts the timer if a
very small value is stored (0, 1, or 2) and raises an interrupt
directly. There are two problem with this on BookE.
First is that BookE says a decrementer interrupt should not be raised
on a store of 0, only of a decrement from 1. Second is that raising
the irq directly will bypass the auto-reload logic in the booke decr
timer function, breaking autoreload when 1 or 2 is stored.
Fix this by removing that small-value special case. It makes this
tricky logic even more difficult to reason about, and it hardly matters
for performance.
Cc: sdicaro@DDCI.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530131214.373524-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 17dd1354c1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When storing a large decrementer value with the most significant
implemented bit set, it is to be treated as a negative and sign
extended.
This isn't hit for book3s DEC because of another bug, fixing it
in the next patch exposes this one and can cause additional
problems, so fix this first. It can be hit with HDECR and other
edge triggered types.
Fixes: a8dafa5251 ("target/ppc: Implement large decrementer support for TCG")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: removed extra cpu and pcc variables shadowing local variables ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit c8fbc6b9f2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The decrementer register contains a relative time in timebase units.
When writing to DECR this is converted and stored as an absolute value
in nanosecond units, reading DECR converts back to relative timebase.
The tb<->ns conversion of the relative part can cause rounding such that
a value writen to the decrementer can read back a different, with time
held constant. This is a particular problem for a deterministic icount
and record-replay trace.
Fix this by storing the absolute value in timebase units rather than
nanoseconds. The math before:
store: decr_next = now_ns + decr * ns_per_sec / tb_per_sec
load: decr = (decr_next - now_ns) * tb_per_sec / ns_per_sec
load(store): decr = decr * ns_per_sec / tb_per_sec * tb_per_sec /
ns_per_sec
After:
store: decr_next = now_ns * tb_per_sec / ns_per_sec + decr
load: decr = decr_next - now_ns * tb_per_sec / ns_per_sec
load(store): decr = decr
Fixes: 9fddaa0c0c ("PowerPC merge: real time TB and decrementer - faster and simpler exception handling (Jocelyn Mayer)")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 8e0a5ac878)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The rule of timers is typically that they should never expire before the
timeout, but some time afterward. Rounding timer intervals up when doing
conversion is the right thing to do.
Under most circumstances it is impossible observe the decrementer
interrupt before the dec register has triggered. However with icount
timing, problems can arise. For example setting DEC to 0 can schedule
the timer for now, causing it to fire before any more instructions
have been executed and DEC is still 0.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit eab0888418)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This will be used for converting time intervals in different base units
to host units, for the purpose of scheduling timers to emulate target
timers. Timers typically must not fire before their requested expiry
time but may fire some time afterward, so rounding up is the right way
to implement these.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[ clg: renamed __muldiv64() to muldiv64_rounding() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 47de6c4c28)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
These calculations are repeated several times, and they will become
a little more complicated with subsequent changes.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 7798f5c576)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555888630 in dpy_ui_info_supported (con=0x0) at ../ui/console.c:812
812 return con->hw_ops->ui_info != NULL;
(gdb) bt
#0 0x0000555555888630 in dpy_ui_info_supported (con=0x0) at ../ui/console.c:812
#1 0x00005555558a44b1 in protocol_client_msg (vs=0x5555578c76c0, data=0x5555581e93f0 <incomplete sequence \373>, len=24) at ../ui/vnc.c:2585
#2 0x00005555558a19ac in vnc_client_read (vs=0x5555578c76c0) at ../ui/vnc.c:1607
#3 0x00005555558a1ac2 in vnc_client_io (ioc=0x5555581eb0e0, condition=G_IO_IN, opaque=0x5555578c76c0) at ../ui/vnc.c:1635
Fixes:
https://issues.redhat.com/browse/RHEL-2600
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Albert Esteve <aesteve@redhat.com>
(cherry picked from commit 48a35e12fa)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ppi command line option for the TIS device on sysbus never worked
and caused an immediate segfault. Remove support for it since it also
needs support in the firmware and needs testing inside the VM.
Reproducer with the ppi=on option passed:
qemu-system-aarch64 \
-machine virt,gic-version=3 \
-m 4G \
-nographic -no-acpi \
-chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0,ppi=on
[...]
Segmentation fault (core dumped)
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230713171955.149236-1-stefanb@linux.ibm.com
(cherry picked from commit 4c46fe2ed4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the rule-lock bypass (RLB) bit is set in the mseccfg CSR, the PMP
configuration lock bits must not apply. While this behavior is
implemented for the pmpcfgX CSRs, this bit is not respected for
changes to the pmpaddrX CSRs. This patch ensures that pmpaddrX CSR
writes work even on locked regions when the global rule-lock bypass is
enabled.
Signed-off-by: Leon Schuermann <leons@opentitan.org>
Reviewed-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230829215046.1430463-1-leon@is.currently.online>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 4e3adce124)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On a dtb dumped from the virt machine, dt-validate complains:
soc: pmu: {'riscv,event-to-mhpmcounters': [[1, 1, 524281], [2, 2, 524284], [65561, 65561, 524280], [65563, 65563, 524280], [65569, 65569, 524280]], 'compatible': ['riscv,pmu']} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
That's pretty cryptic, but running the dtb back through dtc produces
something a lot more reasonable:
Warning (simple_bus_reg): /soc/pmu: missing or empty reg/ranges property
Moving the riscv,pmu node out of the soc bus solves the problem.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230727-groom-decline-2c57ce42841c@spud>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 9ff3140631)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context adjustment due to 568e0614d0 "hw/riscv/virt.c: rename MachineState 'mc' pointers to 'ms'")
The character that should be printed is stored in the 64 bit "payload"
variable. The code currently tries to print it by taking the address
of the variable and passing this pointer to qemu_chr_fe_write(). However,
this only works on little endian hosts where the least significant bits
are stored on the lowest address. To do this in a portable way, we have
to store the value in an uint8_t variable instead.
Fixes: 5033606780 ("RISC-V HTIF Console")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230721094720.902454-2-thuth@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit c255946e3d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: edit to compensate for v7.2.0-805-g753ae97abc and v7.2.0-808-gdadee9e3ce)
virtio_load() as a whole should run in coroutine context because it
reads from the migration stream and we don't want this to block.
However, it calls virtio_set_features_nocheck() and devices don't
expect their .set_features callback to run in a coroutine and therefore
call functions that may not be called in coroutine context. To fix this,
drop out of coroutine context for calling virtio_set_features_nocheck().
Without this fix, the following crash was reported:
#0 __pthread_kill_implementation (threadid=<optimized out>, signo=signo@entry=6, no_tid=no_tid@entry=0) at pthread_kill.c:44
#1 0x00007efc738c05d3 in __pthread_kill_internal (signo=6, threadid=<optimized out>) at pthread_kill.c:78
#2 0x00007efc73873d26 in __GI_raise (sig=sig@entry=6) at ../sysdeps/posix/raise.c:26
#3 0x00007efc738477f3 in __GI_abort () at abort.c:79
#4 0x00007efc7384771b in __assert_fail_base (fmt=0x7efc739dbcb8 "", assertion=assertion@entry=0x560aebfbf5cf "!qemu_in_coroutine()",
file=file@entry=0x560aebfcd2d4 "../block/graph-lock.c", line=line@entry=275, function=function@entry=0x560aebfcd34d "void bdrv_graph_rdlock_main_loop(void)") at assert.c:92
#5 0x00007efc7386ccc6 in __assert_fail (assertion=0x560aebfbf5cf "!qemu_in_coroutine()", file=0x560aebfcd2d4 "../block/graph-lock.c", line=275,
function=0x560aebfcd34d "void bdrv_graph_rdlock_main_loop(void)") at assert.c:101
#6 0x0000560aebcd8dd6 in bdrv_register_buf ()
#7 0x0000560aeb97ed97 in ram_block_added.llvm ()
#8 0x0000560aebb8303f in ram_block_add.llvm ()
#9 0x0000560aebb834fa in qemu_ram_alloc_internal.llvm ()
#10 0x0000560aebb2ac98 in vfio_region_mmap ()
#11 0x0000560aebb3ea0f in vfio_bars_register ()
#12 0x0000560aebb3c628 in vfio_realize ()
#13 0x0000560aeb90f0c2 in pci_qdev_realize ()
#14 0x0000560aebc40305 in device_set_realized ()
#15 0x0000560aebc48e07 in property_set_bool.llvm ()
#16 0x0000560aebc46582 in object_property_set ()
#17 0x0000560aebc4cd58 in object_property_set_qobject ()
#18 0x0000560aebc46ba7 in object_property_set_bool ()
#19 0x0000560aeb98b3ca in qdev_device_add_from_qdict ()
#20 0x0000560aebb1fbaf in virtio_net_set_features ()
#21 0x0000560aebb46b51 in virtio_set_features_nocheck ()
#22 0x0000560aebb47107 in virtio_load ()
#23 0x0000560aeb9ae7ce in vmstate_load_state ()
#24 0x0000560aeb9d2ee9 in qemu_loadvm_state_main ()
#25 0x0000560aeb9d45e1 in qemu_loadvm_state ()
#26 0x0000560aeb9bc32c in process_incoming_migration_co.llvm ()
#27 0x0000560aebeace56 in coroutine_trampoline.llvm ()
Cc: qemu-stable@nongnu.org
Buglink: https://issues.redhat.com/browse/RHEL-832
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20230905145002.46391-3-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 92e2e6a867)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: remove coroutine_mixed_fn markings introduced in v7.2.0-909-g0f3de970fe)
The assert() that checks for valid MTU sizes can be triggered by
the guest (e.g. with the reproducer code from the bug ticket
https://gitlab.com/qemu-project/qemu/-/issues/517 ). Let's avoid
this problem by simply logging the error and refusing to activate
the device instead.
Fixes: d05dcd94ae ("net: vmxnet3: validate configuration values during activate")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
[Mjt: change format specifier from %d to %u for uint32_t argument]
(cherry picked from commit 90a0778421)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
docs/multi-thread-compression.txt uses parameter names with
underscores instead of dashes. Wrong since day one.
docs/rdma.txt, tests/qemu-iotests/181, and tests/qtest/test-hmp.c are
wrong the same way since commit cbde7be900 (v6.0.0). Hard to see,
as test-hmp doesn't check whether the commands work, and iotest 181
appears to be unaffected.
Fixes: 263170e679 (docs: Add a doc about multiple thread compression)
Fixes: cbde7be900 (migrate: remove QMP/HMP commands for speed, downtime and cache size)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit b21a6e31a1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The current description says that these options will create a device
on the IDE bus, which is only true on x86. So rephrase these sentences
a little bit to speak of "default bus" instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit bcd8e24308)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the ast2600 datasheet and the linux aspeed i2c driver,
the TXBUF transmission start position should be TXBUF[0] instead
of TXBUF[1],so the arg pool_start is useless,and the address is not
included in TXBUF.So even if Tx Count equals zero,there is at least
1 byte data needs to be transmitted,and M_TX_CMD should not be cleared
at this condition.The driver url is:
https://github.com/AspeedTech-BMC/linux/blob/aspeed-master-v5.15/drivers/i2c/busses/i2c-ast2600.c
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 6054fc73e8 ("aspeed/i2c: Add support for pool buffer transfers")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 961faf3ddb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 97b8aa5ae9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When encountering an NCQ error, you should not write the NCQ tag to the
SError register. This is completely wrong.
The SError register has a clear definition, where each bit represents a
different error, see PxSERR definition in AHCI 1.3.1.
If we write a random value (like the NCQ tag) in SError, e.g. Linux will
read SError, and will trigger arbitrary error handling depending on the
NCQ tag that happened to be executing.
In case of success, ncq_cb() will call ncq_finish().
In case of error, ncq_cb() will call ncq_err() (which will clear
ncq_tfs->used), and then call ncq_finish(), thus using ncq_tfs->used is
sufficient to tell if finished should get set or not.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-9-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit 9f89423537)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When there is an error, we need to raise a TFES error irq, see AHCI 1.3.1,
5.3.13.1 SDB:Entry.
If ERR_STAT is set, we jump to state ERR:FatalTaskfile, which will raise
a TFES IRQ unconditionally, regardless if the I bit is set in the FIS or
not.
Thus, we should never raise a normal IRQ after having sent an error IRQ.
It is valid to signal successfully completed commands as finished in the
same SDB FIS that generates the error IRQ. The important thing is that
commands that did not complete successfully (e.g. commands that were
aborted, do not get the finished bit set).
Before this commit, there was never a TFES IRQ raised on NCQ error.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-8-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit 7e85cb0db4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
Successfully means ERR_STAT, BUSY and DRQ are all cleared.
A command that has ERR_STAT set, does not get to clear PxCI.
See AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and RegFIS:ClearCI,
and 5.3.16.5 ERR:FatalTaskfile.
In the case of non-NCQ commands, not clearing PxCI is needed in order
for host software to be able to see which command slot that failed.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-7-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit 1a16ce64fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to AHCI 1.3.1 definition of PxSACT:
This field is cleared when PxCMD.ST is written from a '1' to a '0' by
software. This field is not cleared by a COMRESET or a software reset.
According to AHCI 1.3.1 definition of PxCI:
This field is also cleared when PxCMD.ST is written from a '1' to a '0'
by software.
Clearing PxCMD.ST is part of the error recovery procedure, see
AHCI 1.3.1, section "6.2 Error Recovery".
If we don't clear PxCI on error recovery, the previous command will
incorrectly still be marked as pending after error recovery.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-6-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit d73b84d0b6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The AHCI spec states that:
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
(A non-NCQ command that completes with error does not clear PxCI.)
The current QEMU implementation either clears PxCI in check_cmd(),
or in ahci_cmd_done().
check_cmd() will clear PxCI for a command if handle_cmd() returns 0.
handle_cmd() will return -1 if BUSY or DRQ is set.
The QEMU implementation for NCQ commands will currently not set BUSY
or DRQ, so they will always have PxCI cleared by handle_cmd().
ahci_cmd_done() will never even get called for NCQ commands.
Non-NCQ commands are executed by ide_bus_exec_cmd().
Non-NCQ commands in QEMU are implemented either in a sync or in an async
way.
For non-NCQ commands implemented in a sync way, the command handler will
return true, and when ide_bus_exec_cmd() sees that a command handler
returns true, it will call ide_cmd_done() (which will call
ahci_cmd_done()). For a command implemented in a sync way,
ahci_cmd_done() will do nothing (since busy_slot is not set). Instead,
after ide_bus_exec_cmd() has finished, check_cmd() will clear PxCI for
these commands.
For non-NCQ commands implemented in an async way (using either aiocb or
pio_aiocb), the command handler will return false, ide_bus_exec_cmd()
will not call ide_cmd_done(), instead it is expected that the async
callback function will call ide_cmd_done() once the async command is
done. handle_cmd() will set busy_slot, if and only if BUSY or DRQ is
set, and this is checked _after_ ide_bus_exec_cmd() has returned.
handle_cmd() will return -1, so check_cmd() will not clear PxCI.
When the async callback calls ide_cmd_done() (which will call
ahci_cmd_done()), it will see that busy_slot is set, and
ahci_cmd_done() will clear PxCI.
This seems racy, since busy_slot is set _after_ ide_bus_exec_cmd() has
returned. The callback might come before busy_slot gets set. And it is
quite confusing that ahci_cmd_done() will be called for all non-NCQ
commands when the command is done, but will only clear PxCI in certain
cases, even though it will always write a D2H FIS and raise an IRQ.
Even worse, in the case where ahci_cmd_done() does not clear PxCI, it
still raises an IRQ. Host software might thus read an old PxCI value,
since PxCI is cleared (by check_cmd()) after the IRQ has been raised.
Try to simplify this by always setting busy_slot for non-NCQ commands,
such that ahci_cmd_done() will always be responsible for clearing PxCI
for non-NCQ commands.
For NCQ commands, clear PxCI when we receive the D2H FIS, but before
raising the IRQ, see AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and
RegFIS:ClearCI.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-5-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit e2a5d9b3d9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The way that BUSY + PxCI is cleared for NCQ (FPDMA QUEUED) commands is
described in SATA 3.5a Gold:
11.15 FPDMA QUEUED command protocol
DFPDMAQ2: ClearInterfaceBsy
"Transmit Register Device to Host FIS with the BSY bit cleared to zero
and the DRQ bit cleared to zero and Interrupt bit cleared to zero to
mark interface ready for the next command."
PxCI is currently cleared by handle_cmd(), but we don't write the D2H
FIS to the FIS Receive Area that actually caused PxCI to be cleared.
Similar to how ahci_pio_transfer() calls ahci_write_fis_pio() with an
additional parameter to write a PIO Setup FIS without raising an IRQ,
add a parameter to ahci_write_fis_d2h() so that ahci_write_fis_d2h()
also can write the FIS to the FIS Receive Area without raising an IRQ.
Change process_ncq_command() to call ahci_write_fis_d2h() without
raising an IRQ (similar to ahci_pio_transfer()), such that the FIS
Receive Area is in sync with the PxTFD shadow register.
E.g. Linux reads status and error fields from the FIS Receive Area
directly, so it is wise to keep the FIS Receive Area and the PxTFD
shadow register in sync.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-4-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit 2967dc8209)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, the first time sending an unsupported command
(e.g. READ LOG DMA EXT) will not have ERR_STAT set in the completion.
Sending the unsupported command again, will correctly have ERR_STAT set.
When ide_cmd_permitted() returns false, it calls ide_abort_command().
ide_abort_command() first calls ide_transfer_stop(), which will call
ide_transfer_halt() and ide_cmd_done(), after that ide_abort_command()
sets ERR_STAT in status.
ide_cmd_done() for AHCI will call ahci_write_fis_d2h() which writes the
current status in the FIS, and raises an IRQ. (The status here will not
have ERR_STAT set!).
Thus, we cannot call ide_transfer_stop() before setting ERR_STAT, as
ide_transfer_stop() will result in the FIS being written and an IRQ
being raised.
The reason why it works the second time, is that ERR_STAT will still
be set from the previous command, so when writing the FIS, the
completion will correctly have ERR_STAT set.
Set ERR_STAT before writing the FIS (calling cmd_done), so that we will
raise an error IRQ correctly when receiving an unsupported command.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-3-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit c3461c6264)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Failing to reset the of_instance_last makes ihandle allocation continue
to increase, which causes record-replay replay fail to match the
recorded trace.
Not resetting claimed_base makes VOF eventually run out of memory after
some resets.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Fixes: fc8c745d50 ("spapr: Implement Open Firmware client interface")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 7b8589d7ce)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ppce500_reset_device_tree is registered for system reset, but after
c4b075318e this function rerandomizes rng-seed via
qemu_guest_getrandom_nofail. And when loading a snapshot, it tries to read
EVENT_RANDOM that doesn't exist, so we have an error:
qemu-system-ppc: Missing random event in the replay log
To fix this, use qemu_register_reset_nosnapshotload instead of
qemu_register_reset.
Reported-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Fixes: c4b075318e ("hw/ppc: pass random seed to fdt ")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1634
Signed-off-by: Maksim Kostin <maksim.kostin@ispras.ru>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 6ec65b69ba)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We can fail the blk_insert_bs() at init_blk_migration(), leaving the
BlkMigDevState without a dirty_bitmap and BlockDriverState. Account
for the possibly missing elements when doing cleanup.
Fix the following crashes:
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555ec83ef in bdrv_release_dirty_bitmap (bitmap=0x0) at ../block/dirty-bitmap.c:359
359 BlockDriverState *bs = bitmap->bs;
#0 0x0000555555ec83ef in bdrv_release_dirty_bitmap (bitmap=0x0) at ../block/dirty-bitmap.c:359
#1 0x0000555555bba331 in unset_dirty_tracking () at ../migration/block.c:371
#2 0x0000555555bbad98 in block_migration_cleanup_bmds () at ../migration/block.c:681
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555e971ff in bdrv_op_unblock (bs=0x0, op=BLOCK_OP_TYPE_BACKUP_SOURCE, reason=0x0) at ../block.c:7073
7073 QLIST_FOREACH_SAFE(blocker, &bs->op_blockers[op], list, next) {
#0 0x0000555555e971ff in bdrv_op_unblock (bs=0x0, op=BLOCK_OP_TYPE_BACKUP_SOURCE, reason=0x0) at ../block.c:7073
#1 0x0000555555e9734a in bdrv_op_unblock_all (bs=0x0, reason=0x0) at ../block.c:7095
#2 0x0000555555bbae13 in block_migration_cleanup_bmds () at ../migration/block.c:690
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Message-id: 20230731203338.27581-1-farosas@suse.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit f187609f27)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Before this change, the default KVM type, which is used for non-virt
machine models, was 0.
The kernel documentation says:
> On arm64, the physical address size for a VM (IPA Size limit) is
> limited to 40bits by default. The limit can be configured if the host
> supports the extension KVM_CAP_ARM_VM_IPA_SIZE. When supported, use
> KVM_VM_TYPE_ARM_IPA_SIZE(IPA_Bits) to set the size in the machine type
> identifier, where IPA_Bits is the maximum width of any physical
> address used by the VM. The IPA_Bits is encoded in bits[7-0] of the
> machine type identifier.
>
> e.g, to configure a guest to use 48bit physical address size::
>
> vm_fd = ioctl(dev_fd, KVM_CREATE_VM, KVM_VM_TYPE_ARM_IPA_SIZE(48));
>
> The requested size (IPA_Bits) must be:
>
> == =========================================================
> 0 Implies default size, 40bits (for backward compatibility)
> N Implies N bits, where N is a positive integer such that,
> 32 <= N <= Host_IPA_Limit
> == =========================================================
> Host_IPA_Limit is the maximum possible value for IPA_Bits on the host
> and is dependent on the CPU capability and the kernel configuration.
> The limit can be retrieved using KVM_CAP_ARM_VM_IPA_SIZE of the
> KVM_CHECK_EXTENSION ioctl() at run-time.
>
> Creation of the VM will fail if the requested IPA size (whether it is
> implicit or explicit) is unsupported on the host.
https://docs.kernel.org/virt/kvm/api.html#kvm-create-vm
So if Host_IPA_Limit < 40, specifying 0 as the type will fail. This
actually confused libvirt, which uses "none" machine model to probe the
KVM availability, on M2 MacBook Air.
Fix this by using Host_IPA_Limit as the default type when
KVM_CAP_ARM_VM_IPA_SIZE is available.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-3-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 1ab445af8c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
kvm_arch_get_default_type() returns the default KVM type. This hook is
particularly useful to derive a KVM type that is valid for "none"
machine model, which is used by libvirt to probe the availability of
KVM.
For MIPS, the existing mips_kvm_type() is reused. This function ensures
the availability of VZ which is mandatory to use KVM on the current
QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-2-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added doc comment for new function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 5e0d65909c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Using "-device virtio-gpu,blob=true" currently does not work on big
endian hosts (like s390x). The guest kernel prints an error message
like:
[drm:virtio_gpu_dequeue_ctrl_func [virtio_gpu]] *ERROR* response 0x1200 (command 0x10c)
and the display stays black. When running QEMU with "-d guest_errors",
it shows an error message like this:
virtio_gpu_create_mapping_iov: nr_entries is too big (83886080 > 16384)
which indicates that this value has not been properly byte-swapped.
And indeed, the virtio_gpu_create_blob_bswap() function (that should
swap the fields in the related structure) fails to swap some of the
entries. After correctly swapping all missing values here, too, the
virtio-gpu device is now also working with blob=true on s390x hosts.
Fixes: e0933d91b1 ("virtio-gpu: Add virtio_gpu_resource_create_blob")
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2230469
Message-Id: <20230815122007.928049-1-thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit d194362910)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unlike most other instructions that contain an immediate element index,
VREP's one is 16-bit, and not 4-bit. The code uses only 8 bits, so
using, e.g., 0x101 does not lead to a specification exception.
Fix by checking all 16 bits.
Cc: qemu-stable@nongnu.org
Fixes: 28d08731b1 ("s390x/tcg: Implement VECTOR REPLICATE")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230807163459.849766-1-iii@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 23e87d419f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
OpenRISC (or1k) has long long alignment to 4 bytes, but currently not
defined in abitypes.h. This lead to incorrect packing of /epoll_event/
structure and eventually infinite loop while waiting for file
descriptor[s] event[s].
Fixed also CRIS alignments (1 byte for all types).
Signed-off-by: Luca Bonissi <qemu@bonslack.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1770
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 6ee960823d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Based on gcc's nios2.h setting BIGGEST_ALIGNMENT to 32 bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit ea9812d93f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Based on gcc's microblaze.h setting BIGGEST_ALIGNMENT to 32 bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit e73f27003e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The kdump-zlib data pages are not dumped from aarch64 host when the
'pvtime' is involved, that is, when the block->target_end is not aligned to
page_size. In the below example, it is expected to dump two blocks.
(qemu) info mtree -f
... ...
00000000090a0000-00000000090a0fff (prio 0, ram): pvtime KVM
... ...
0000000040000000-00000001bfffffff (prio 0, ram): mach-virt.ram KVM
... ...
However, there is an issue with get_next_page() so that the pages for
"mach-virt.ram" will not be dumped.
At line 1296, although we have reached at the end of the 'pvtime' block,
since it is not aligned to the page_size (e.g., 0x10000), it will not break
at line 1298.
1255 static bool get_next_page(GuestPhysBlock **blockptr, uint64_t *pfnptr,
1256 uint8_t **bufptr, DumpState *s)
... ...
1294 memcpy(buf + addr % page_size, hbuf, n);
1295 addr += n;
1296 if (addr % page_size == 0) {
1297 /* we filled up the page */
1298 break;
1299 }
As a result, get_next_page() will continue to the next
block ("mach-virt.ram"). Finally, when get_next_page() returns to the
caller:
- 'pfnptr' is referring to the 'pvtime'
- but 'blockptr' is referring to the "mach-virt.ram"
When get_next_page() is called the next time, "*pfnptr += 1" still refers
to the prior 'pvtime'. It will exit immediately because it is out of the
range of the current "mach-virt.ram".
The fix is to break when it is time to come to the next block, so that both
'pfnptr' and 'blockptr' refer to the same block.
Fixes: 94d788408d ("dump: fix kdump to work over non-aligned blocks")
Cc: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230713055819.30497-1-dongli.zhang@oracle.com>
(cherry picked from commit 8a64609eea)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
>From SMBIOS 3.0 specification, core count field means:
Core Count is the number of cores detected by the BIOS for this
processor socket. [1]
Before 003f230e37 ("machine: Tweak the order of topology members in
struct CpuTopology"), MachineState.smp.cores means "the number of cores
in one package", and it's correct to use smp.cores for core count.
But 003f230e37 changes the smp.cores' meaning to "the number of cores
in one die" and doesn't change the original smp.cores' use in smbios as
well, which makes core count in type4 go wrong.
Fix this issue with the correct "cores per socket" caculation.
[1] SMBIOS 3.0.0, section 7.5.6, Processor Information - Core Count
Fixes: 003f230e37 ("machine: Tweak the order of topology members in struct CpuTopology")
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20230628135437.1145805-5-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 196ea60a73)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
>From SMBIOS 3.0 specification, thread count field means:
Thread Count is the total number of threads detected by the BIOS for
this processor socket. It is a processor-wide count, not a
thread-per-core count. [1]
So here we should use threads per socket other than threads per core.
[1] SMBIOS 3.0.0, section 7.5.8, Processor Information - Thread Count
Fixes: c97294ec1b ("SMBIOS: Build aggregate smbios tables and entry point")
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20230628135437.1145805-4-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 7298fd7de5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
smp.sockets is the number of sockets which is configured by "-smp" (
otherwise, the default is 1). Trying to recalculate it here with another
rules leads to errors, such as:
1. 003f230e37 ("machine: Tweak the order of topology members in struct
CpuTopology") changes the meaning of smp.cores but doesn't fix
original smp.cores uses.
With the introduction of cluster, now smp.cores means the number of
cores in one cluster. So smp.cores * smp.threads just means the
threads in a cluster not in a socket.
2. On the other hand, we shouldn't use smp.cpus here because it
indicates the initial number of online CPUs at the boot time, and is
not mathematically related to smp.sockets.
So stop reinventing the another wheel and use the topo values that
has been calculated.
Fixes: 003f230e37 ("machine: Tweak the order of topology members in struct CpuTopology")
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20230628135437.1145805-3-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit d79a284a44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The number of cores/threads per socket are needed for smbios, and are
also useful for other modules.
Provide the helpers to wrap the calculation of cores/threads per socket
so that we can avoid calculation errors caused by other modules miss
topology changes.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20230628135437.1145805-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit a1d027be95)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
While trying to use a SCSI disk on the LSI controller with an
older version of Fedora (25), I'm getting:
qemu: warning: Blocked re-entrant IO on MemoryRegion: lsi-mmio at addr: 0x34
and the SCSI controller is not usable. Seems like we have to
disable the reentrancy checker for the MMIO region, too, to
get this working again.
The problem could be reproduced it like this:
./qemu-system-x86_64 -accel kvm -m 2G -machine q35 \
-device lsi53c810,id=lsi1 -device scsi-hd,drive=d0 \
-drive if=none,id=d0,file=.../somedisk.qcow2 \
-cdrom Fedora-Everything-netinst-i386-25-1.3.iso
Where somedisk.qcow2 is an image that contains already some partitions
and file systems.
In the boot menu of Fedora, go to
"Troubleshooting" -> "Rescue a Fedora system" -> "3) Skip to shell"
Then check "dmesg | grep -i 53c" for failure messages, and try to mount
a partition from somedisk.qcow2.
Message-Id: <20230516090556.553813-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit d139fe9ad8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
As the code is designed to use the memory APIs to access the script ram,
disable reentrancy checks for the pseudo-RAM ram_io MemoryRegion.
In the future, ram_io may be converted from an IO to a proper RAM MemoryRegion.
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20230427211013.2994127-6-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit bfd6e7ae6a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Devices can pass their MemoryReentrancyGuard (from their DeviceState),
when creating new BHes. Then, the async API will toggle the guard
before/after calling the BH call-back. This prevents bh->mmio reentrancy
issues.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20230427211013.2994127-3-alxndr@bu.edu>
[thuth: Fix "line over 90 characters" checkpatch.pl error]
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 9c86c97f12)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
[mjt: minor context adjustment in include/block/aio.h and include/qemu/main-loop.h for 7.2]
The pipenv tool was nice in theory, but in practice it's just too hard
to update selectively, and it makes using it a pain. The qemu.qmp repo
dropped pipenv support a while back and it's been functioning just fine,
so I'm backporting that change here to qemu.git.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20230210003147.1309376-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
(cherry picked from commit 6832189fd7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: the reason for this is to stop CI failing in pipenv for 7.2)
There's one commit, tagged v7.2.2, without Signed-off-by line.
Due to this, check-dco test always fail on 7.2. Since this is
a stable branch with almost all commits coming from master
already with S-o-b (except of the version bumps and very rare
stable-specific commits), and v7.2.2 is already cast in stone,
let's base the check on stable-7.2 branch (with its last version)
instead of master branch. This way, staging-7.2 will be checked
against stable-7.2, but stable-7.2 itself will not be checked
anymore, - so we can catch errors during stable preparations.
Note: this is a change specific to stable-7.2 branch/series, it
is not supposed to be in master.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When CR0.TS=1, execution of x87 FPU, MMX, and some SSE instructions will
cause a Device Not Available (DNA) exception (#NM). System software uses
this exception event to lazily context switch FPU state.
Before this patch, enter_mmx helpers may be generated just before #NM
generation, prematurely resetting FPU state before the guest has a
chance to save it.
Signed-off-by: Matt Borgerson <contact@mborgerson.com>
Message-ID: <CADc=-s5F10muEhLs4f3mxqsEPAHWj0XFfOC2sfFMVHrk9fcpMg@mail.gmail.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit b2ea6450d8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Until v2.07s, the VRMA page size (L||LP) was encoded in LPCR[VRMASD].
In v3.0 that moved to the partition table PS field.
The powernv machine can now run KVM HPT guests on POWER9/10 CPUs with
this fix and the patch to add ASDR.
Fixes: 3367c62f52 ("target/ppc: Support for POWER9 native hash")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230730111842.39292-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 0e2a3ec368)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
HDEC is defined to not wake from PM state. There is a check in the HDEC
timer to avoid setting the interrupt if we are in a PM state, but no
check on PM entry to lower HDEC if it already fired. This can cause a
HDECR wake up and QEMU abort with unsupported exception in Power Save
mode.
Fixes: 4b236b621b ("ppc: Initial HDEC support")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230726182230.433945-4-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 9915dac484)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ASDR register was introduced in ISA v3.0. It has not been
implemented for HPT. With HPT, ASDR is the format of the slbmte RS
operand (containing VSID), which matches the ppc_slb_t field.
Fixes: 3367c62f52 ("target/ppc: Support for POWER9 native hash")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230726182230.433945-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 9201af0969)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to VirtIO standard, "The class, command and
command-specific-data are set by the driver,
and the device sets the ack byte.
There is little it can do except issue a diagnostic
if ack is not VIRTIO_NET_OK."
Therefore, QEMU should stop sending the queued SVQ commands and
cancel the device startup if the device's ack is not VIRTIO_NET_OK.
Yet the problem is that, vhost_vdpa_net_load_mq() returns 1 based on
`*s->status != VIRTIO_NET_OK` when the device's ack is VIRTIO_NET_ERR.
As a result, net->nc->info->load() also returns 1, this makes
vhost_net_start_one() incorrectly assume the device state is
successfully loaded by vhost_vdpa_net_load() and return 0, instead of
goto `fail` label to cancel the device startup, as vhost_net_start_one()
only cancels the device startup when net->nc->info->load() returns a
negative value.
This patch fixes this problem by returning -EIO when the device's
ack is not VIRTIO_NET_OK.
Fixes: f64c7cda69 ("vdpa: Add vhost_vdpa_net_load_mq")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <ec515ebb0b4f56368751b9e318e245a5d994fa72.1688438055.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit f45fd95ec9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to VirtIO standard, "The class, command and
command-specific-data are set by the driver,
and the device sets the ack byte.
There is little it can do except issue a diagnostic
if ack is not VIRTIO_NET_OK."
Therefore, QEMU should stop sending the queued SVQ commands and
cancel the device startup if the device's ack is not VIRTIO_NET_OK.
Yet the problem is that, vhost_vdpa_net_load_mac() returns 1 based on
`*s->status != VIRTIO_NET_OK` when the device's ack is VIRTIO_NET_ERR.
As a result, net->nc->info->load() also returns 1, this makes
vhost_net_start_one() incorrectly assume the device state is
successfully loaded by vhost_vdpa_net_load() and return 0, instead of
goto `fail` label to cancel the device startup, as vhost_net_start_one()
only cancels the device startup when net->nc->info->load() returns a
negative value.
This patch fixes this problem by returning -EIO when the device's
ack is not VIRTIO_NET_OK.
Fixes: f73c0c43ac ("vdpa: extract vhost_vdpa_net_load_mac from vhost_vdpa_net_load")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <a21731518644abbd0c495c5b7960527c5911f80d.1688438055.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit b479bc3c9d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU uses vhost_handle_guest_kick() to forward guest's available
buffers to the vdpa device in SVQ avail ring.
In vhost_handle_guest_kick(), a `g_autofree` `elem` is used to
iterate through the available VirtQueueElements. This `elem` is
then passed to `svq->ops->avail_handler`, specifically to the
vhost_vdpa_net_handle_ctrl_avail(). If this handler fails to
process the CVQ command, vhost_handle_guest_kick() regains
ownership of the `elem`, and either frees it or requeues it.
Yet the problem is that, vhost_vdpa_net_handle_ctrl_avail()
mistakenly frees the `elem`, even if it fails to forward the
CVQ command to vdpa device. This can result in a use-after-free
for the `elem` in vhost_handle_guest_kick().
This patch solves this problem by refactoring
vhost_vdpa_net_handle_ctrl_avail() to only freeing the `elem` if
it owns it.
Fixes: bd907ae4b0 ("vdpa: manual forward CVQ buffers")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <e3f2d7db477734afe5c6a5ab3fa8b8317514ea34.1688746840.git.yin31149@gmail.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 031b1abacb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When vfio realize fails, INTx isn't disabled if it has been enabled.
This may confuse host side with unhandled interrupt report.
Fixes: c5478fea27 ("vfio/pci: Respond to KVM irqchip change notifier")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit adee0da036)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The first bitfield here is supposed to be used as a 64-bit equivalent
to the "uint64_t msi_addr" in the union. To make this work correctly
on big endian hosts, too, the __addr_hi field has to be part of the
bitfield, and the the bitfield members must be declared with "uint64_t"
instead of "uint32_t" - otherwise the values are placed in the wrong
bytes on big endian hosts.
Same applies to the 32-bit "msi_data" field: __resved1 must be part
of the bitfield, and the members must be declared with "uint32_t"
instead of "uint16_t".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-7-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit e1e56c07d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On big endian hosts, we need to reverse the bitfield order in the
struct VTDInvDescIEC, just like it is already done for the other
bitfields in the various structs of the intel-iommu device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-4-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit 4572b22cf9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The code already tries to do some endianness handling here, but
currently fails badly:
- While it already swaps the data when logging errors / tracing, it fails
to byteswap the value before e.g. accessing entry->irte.present
- entry->irte.source_id is swapped with le32_to_cpu(), though this is
a 16-bit value
- The whole union is apparently supposed to be swapped via the 64-bit
data[2] array, but the struct is a mixture between 32 bit values
(the first 8 bytes) and 64 bit values (the second 8 bytes), so this
cannot work as expected.
Fix it by converting the struct to two proper 64-bit bitfields, and
by swapping the values only once for everybody right after reading
the data from memory.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-3-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit 642ba89672)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On hppa the Instruction Address Offset Queue (IAOQ) registers specifies
the next to-be-executed instructions addresses. Each generated TB writes those
registers at least once, so those registers are used heavily in generated
code.
Looking at the generated assembly, for a x86-64 host this code
to write the address $0x7ffe826f into iaoq_f is generated:
0x7f73e8000184: c7 85 d4 01 00 00 6f 82 movl $0x7ffe826f, 0x1d4(%rbp)
0x7f73e800018c: fe 7f
0x7f73e800018e: c7 85 d8 01 00 00 73 82 movl $0x7ffe8273, 0x1d8(%rbp)
0x7f73e8000196: fe 7f
With the trivial change, by moving the variables iaoq_f and iaoq_b to
the top of struct CPUArchState, the offset to %rbp is reduced (from
0x1d4 to 0), which allows the x86-64 tcg to generate 3 bytes less of
generated code per move instruction:
0x7fc1e800018c: c7 45 00 6f 82 fe 7f movl $0x7ffe826f, (%rbp)
0x7fc1e8000193: c7 45 04 73 82 fe 7f movl $0x7ffe8273, 4(%rbp)
Overall this is a reduction of generated code (not a reduction of
number of instructions).
A test run with checks the generated code size by running "/bin/ls"
with qemu-user shows that the code size shrinks from 1616767 to 1569273
bytes, which is ~97% of the former size.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
(cherry picked from commit f8c0fd9804)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For symmetric algorithms, the length of ciphertext must be as same
as the plaintext.
The missing verification of the src_len and the dst_len in
virtio_crypto_sym_op_helper() may lead buffer overflow/divulged.
This patch is originally written by Yiming Tao for QEMU-SECURITY,
resend it(a few changes of error message) in qemu-devel.
Fixes: CVE-2023-3180
Fixes: 04b9b37edda("virtio-crypto: add data queue processing handler")
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Cc: Yiming Tao <taoym@zju.edu.cn>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20230803024314.29962-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 9d38a84347)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the virtio_iommu_handle_command() when a PROBE request is handled,
output_size takes a value greater than the tail size and on a subsequent
iteration we can get a stack out-of-band access. Initialize the
output_size on each iteration.
The issue was found with ASAN. Credits to:
Yiming Tao(Zhejiang University)
Gaoning Pan(Zhejiang University)
Fixes: 1733eebb9e ("virtio-iommu: Implement RESV_MEM probe request")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Mauro Matteo Cascella <mcascell@redhat.com>
Cc: qemu-stable@nongnu.org
Message-Id: <20230717162126.11693-1-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit cf2f89edf3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The arguments for deposit64 are (value, start, length, fieldval); this
appears to have thought they were (value, fieldval, start,
length). Reorder the parameters to match the actual function.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Fixes: d1e23cbaa4 ("target/nios2: Use semihosting/syscalls.h")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230731235245.295513-1-keithp@keithp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 71e2dd6aa1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The TLS handshake make take some time to complete, during which time an
I/O watch might be registered with the main loop. If the owner of the
I/O channel invokes qio_channel_close() while the handshake is waiting
to continue the I/O watch must be removed. Failing to remove it will
later trigger the completion callback which the owner is not expecting
to receive. In the case of the VNC server, this results in a SEGV as
vnc_disconnect_start() tries to shutdown a client connection that is
already gone / NULL.
CVE-2023-3354
Reported-by: jiangyegen <jiangyegen@huawei.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
(cherry picked from commit 10be627d2b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 1898293990 ("xen-block: Use specific blockdev driver")
introduced a new error path, without taking care of allocated
resources.
So only allocate the qdicts after the error check, and free both
`filename` and `driver` when we are about to return and thus taking
care of both success and error path.
Coverity only spotted the leak of qdicts (*_layer variables).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: Coverity CID 1508722, 1398649
Fixes: 1898293990 ("xen-block: Use specific blockdev driver")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230704171819.42564-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
(cherry picked from commit aa36243514)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
thread_pool_free() might have been called on the `pool`, which would
be a reason for worker_thread() to quit. In this case,
`pool->request_cond` is been destroyed.
If worker_thread() didn't managed to signal `request_cond` before it
been destroyed by thread_pool_free(), we got:
util/qemu-thread-posix.c:198: qemu_cond_signal: Assertion `cond->initialized' failed.
One backtrace:
__GI___assert_fail (assertion=0x55555614abcb "cond->initialized", file=0x55555614ab88 "util/qemu-thread-posix.c", line=198,
function=0x55555614ad80 <__PRETTY_FUNCTION__.17104> "qemu_cond_signal") at assert.c:101
qemu_cond_signal (cond=0x7fffb800db30) at util/qemu-thread-posix.c:198
worker_thread (opaque=0x7fffb800dab0) at util/thread-pool.c:129
qemu_thread_start (args=0x7fffb8000b20) at util/qemu-thread-posix.c:505
start_thread (arg=<optimized out>) at pthread_create.c:486
Reported here:
https://lore.kernel.org/all/ZJwoK50FcnTSfFZ8@MacBook-Air-de-Roger.local/T/#u
To avoid issue, keep lock while sending a signal to `request_cond`.
Fixes: 900fa208f5 ("thread-pool: replace semaphore with condition variable")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230714152720.5077-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
(cherry picked from commit f4f71363fc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The custom action uses cmd.exe to run VSS Service installation
and removal which causes an interactive command shell to spawn.
This shell can be used to execute any commands as a SYSTEM user.
Even if call qemu-ga.exe directly the interactive command shell
will be spawned as qemu-ga.exe is a console application and used
by users from the console as well as a service.
As VSS Service runs from DLL which contains the installer and
uninstaller code, it can be run directly by rundll32.exe without
any interactive command shell.
Add specific entry points for rundll which is just a wrapper
for COMRegister/COMUnregister functions with proper arguments.
resolves: https://bugzilla.redhat.com/show_bug.cgi?id=2167423
fixes: CVE-2023-0664 (part 2 of 2)
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Yan Vugenfirer <yvugenfi@redhat.com>
Reported-by: Brian Wiltse <brian.wiltse@live.com>
(cherry picked from commit 07ce178a2b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 7f4f0d9ea8 ("linux-user/arm: Implement __kernel_cmpxchg with host
atomics") switched to use qatomic_cmpxchg() to swap a word with the memory
content, but missed to endianess-swap the oldval and newval values when
emulating an armeb CPU, which expects words to be stored in big endian in
the guest memory.
The bug can be verified with qemu >= v7.0 on any little-endian host, when
starting the armeb binary of the upx program, which just hangs without
this patch.
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: "Markus F.X.J. Oberhumer" <markus@oberhumer.com>
Reported-by: John Reiser <jreiser@BitWagon.com>
Closes: https://github.com/upx/upx/issues/687
Message-Id: <ZMQVnqY+F+5sTNFd@p100>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 38dd78c41e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The change to use translator_use_goto_tb went too far, as the
CF_SINGLE_STEP flag managed by the translator only handles
gdb single stepping and not the architectural single stepping
modeled in DisasContext.singlestep_enabled.
Fixes: 6e9cc373ec ("target/ppc: Use translator_use_goto_tb")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1795
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 2e718e6657)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In commit 0b188ea05a we changed the implementation of
trans_CSEL() to use tcg_constant_i32(). However, this change
was incorrect, because the implementation of the function
sets up the TCGv_i32 rn and rm to be either zero or else
a TCG temp created in load_reg(), and these TCG temps are
then in both cases written to by the emitted TCG ops.
The result is that we hit a TCG assertion:
qemu-system-arm: ../../tcg/tcg.c:4455: tcg_reg_alloc_mov: Assertion `!temp_readonly(ots)' failed.
(or on a non-debug build, just produce a garbage result)
Adjust the code so that rn and rm are always writeable
temporaries whether the instruction is using the special
case "0" or a normal register as input.
Cc: qemu-stable@nongnu.org
Fixes: 0b188ea05a ("target/arm: Use tcg_constant in trans_CSEL")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230727103906.2641264-1-peter.maydell@linaro.org
(cherry picked from commit 2b0d656ab6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in target/arm/tcg/translate.c)
The implementation of the SMMUv3 has multiple places where it reads a
data structure from the guest and directly operates on it without
doing a guest-to-host endianness conversion. Since all SMMU data
structures are little-endian, this means that the SMMU doesn't work
on a big-endian host. In particular, this causes the Avocado test
machine_aarch64_virt.py:Aarch64VirtMachine.test_alpine_virt_tcg_gic_max
to fail on an s390x host.
Add appropriate byte-swapping on reads and writes of guest in-memory
data structures so that the device works correctly on big-endian
hosts.
As part of this we constrain queue_read() to operate only on Cmd
structs and queue_write() on Evt structs, because in practice these
are the only data structures the two functions are used with, and we
need to know what the data structure is to be able to byte-swap its
parts correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230717132641.764660-1-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
(cherry picked from commit c6445544d4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to PCIe Address Translation Services specification 5.1.3.,
ATS Control Register has Enable bit to enable/disable ATS. Guest may
enable/disable PCI ATS and, accordingly, Device-TLB for the VirtIO PCI
device. So, raise/lower a flag and call a trigger function to pass this
event to a device implementation.
Signed-off-by: Viktor Prutyanov <viktor@daynix.com>
Message-Id: <20230512135122.70403-2-viktor@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 206e91d143)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: include/hw/virtio/virtio.h: skip extra struct field added in 8.0)
The test in tests/avocado/machine_loongarch.py is currently failing
on big endian hosts like s390x. By comparing the traces between running
the QEMU_EFI.fd bios on a s390x and on a x86 host, it's quickly obvious
that the CSRRD instruction for the CPUID is behaving differently. And
indeed: The code currently does a long read (i.e. 64 bit) from the
address that points to the CPUState->cpu_index field (with tcg_gen_ld_tl()
in the trans_csrrd() function). But this cpu_index field is only an "int"
(i.e. 32 bit). While this dirty pointer magic works on little endian hosts,
it of course fails on big endian hosts. Fix it by using a proper helper
function instead.
Message-Id: <20230720175307.854460-1-thuth@redhat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit c34ad45992)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unfortunately
commit 03b6762144
(7.2: 6e216d21b5)
Author: Denis V. Lunev <den@openvz.org>
Date: Mon Jul 17 16:55:40 2023 +0200
qemu-nbd: pass structure into nbd_client_thread instead of plain char*
has introduced a regression. struct NbdClientOpts resides on stack inside
'if' block. This specifically means that this stack space could be reused
once the execution will leave that block of the code.
This means that parameters passed into nbd_client_thread could be
overwritten at any moment.
The patch moves the data to the namespace of main() function effectively
preserving it for the whole process lifetime.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Eric Blake <eblake@redhat.com>
CC: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
CC: <qemu-stable@nongnu.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20230727105828.324314-1-den@openvz.org>
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit e5b815b0de)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: add reference to 6e216d21b5 for 7.2 branch)
Commit e6df58a557
Author: Hanna Reitz <hreitz@redhat.com>
Date: Wed May 8 23:18:18 2019 +0200
qemu-nbd: Do not close stderr
has introduced an interesting regression. Original behavior of
ssh somehost qemu-nbd /home/den/tmp/file -f raw --fork
was the following:
* qemu-nbd was started as a daemon
* the command execution is done and ssh exited with success
The patch has changed this behavior and 'ssh' command now hangs forever.
According to the normal specification of the daemon() call, we should
endup with STDERR pointing to /dev/null. That should be done at the
very end of the successful startup sequence when the pipe to the
bootstrap process (used for diagnostics) is no longer needed.
This could be achived in the same way as done for 'qemu-nbd -c' case.
That was commit 0eaf453e, also fixing up e6df58a5. STDOUT copying to
STDERR does the trick.
This also leads to proper 'ssh' connection closing which fixes my
original problem.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Eric Blake <eblake@redhat.com>
CC: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
CC: Hanna Reitz <hreitz@redhat.com>
CC: <qemu-stable@nongnu.org>
Message-ID: <20230717145544.194786-3-den@openvz.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
(cherry picked from commit 5c56dd27a2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A wrong exit condition may lead to an infinite loop when inflating a
valid zlib buffer containing some extra bytes in the `inflate_buffer`
function. The bug only occurs post-authentication. Return the buffer
immediately if the end of the compressed data has been reached
(Z_STREAM_END).
Fixes: CVE-2023-3255
Fixes: 0bf41cab ("ui/vnc: clipboard support")
Reported-by: Kevin Denis <kevin.denis@synacktiv.com>
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230704084210.101822-1-mcascell@redhat.com>
(cherry picked from commit d921fea338)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the 82371FB documentation (82371FB.pdf, 2.3.9. BMIBA-BUS
MASTER INTERFACE BASE ADDRESS REGISTER, April 1997), the register is
32bit wide. To properly reset it to default values, all 32bit need to be
cleared. Bit #0 "Resource Type Indicator (RTE)" needs to be enabled.
The initial change wrote just the lower 8 bit, leaving parts of the "Bus
Master Interface Base Address" address at bit 15:4 unchanged.
Fixes: e6a71ae327 ("Add support for 82371FB (Step A1) and Improved support for 82371SB (Function 1)")
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230712074721.14728-1-olaf@aepfle.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 230dfd9257)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When vfio_enable_vectors() returns with less than requested nr_vectors
we retry with what kernel reported back. But the retry path doesn't
call vfio_prepare_kvm_msi_virq_batch() and this results in,
qemu-system-aarch64: vfio: Error: Failed to enable 4 MSI vectors, retry with 1
qemu-system-aarch64: ../hw/vfio/pci.c:602: vfio_commit_kvm_msi_virq_batch: Assertion `vdev->defer_kvm_irq_routing' failed
Fixes: dc580d51f7 ("vfio: defer to commit kvm irq routing when enable msi/msix")
Reviewed-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit c174088923)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The kvm irqchip notifier is only registered if the device supports
INTx, however it's unconditionally removed in vfio realize error
path. If the assigned device does not support INTx, this will cause
QEMU to crash when vfio realize fails. Change it to conditionally
remove the notifier only if the notify hook is setup.
Before fix:
(qemu) device_add vfio-pci,host=81:11.1,id=vfio1,bus=root1,xres=1
Connection closed by foreign host.
After fix:
(qemu) device_add vfio-pci,host=81:11.1,id=vfio1,bus=root1,xres=1
Error: vfio 0000:81:11.1: xres and yres properties require display=on
(qemu)
Fixes: c5478fea27 ("vfio/pci: Respond to KVM irqchip change notifier")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit 357bd7932a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It is possible to store a very large value to the decrementer that it
does not raise the decrementer exception so the timer is scheduled, but
the next time value wraps and is treated as in the past.
This can occur if (u64)-1 is stored on a zero-triggered exception, or
(u64)-1 is stored twice on an underflow-triggered exception, for
example.
If such a value is set in DECAR, it gets stored to the decrementer by
the timer function, which then immediately causes another timer, which
hangs QEMU.
Clamp the decrementer to the implemented width, and use that as the
value for the timer calculation, effectively preventing this overflow.
Reported-by: sdicaro@DDCI.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530131214.373524-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 09d2db9f46)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The icount-based QEMU_CLOCK_VIRTUAL runs ahead of the RT clock at times.
When warping, it is possible it is still ahead at the end of the warp,
which causes icount adaptive mode to adjust it backward. This can result
in the machine observing time going backwards.
Prevent this by clamping adaptive adjustment to 0 at minimum.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20230627061406.241847-1-npiggin@gmail.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 67f85346ca)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When a peer nic is still attached to the vdpa backend, it is too early to free
up the vhost-net and vdpa structures. If these structures are freed here, then
QEMU crashes when the guest is being shut down. The following call chain
would result in an assertion failure since the pointer returned from
vhost_vdpa_get_vhost_net() would be NULL:
do_vm_stop() -> vm_state_notify() -> virtio_set_status() ->
virtio_net_vhost_status() -> get_vhost_net().
Therefore, we defer freeing up the structures until at guest shutdown
time when qemu_cleanup() calls net_cleanup() which then calls
qemu_del_net_client() which would eventually call vhost_vdpa_cleanup()
again to free up the structures. This time, the loop in net_cleanup()
ensures that vhost_vdpa_cleanup() will be called one last time when
all the peer nics are detached and freed.
All unit tests pass with this change.
CC: imammedo@redhat.com
CC: jusual@redhat.com
CC: mst@redhat.com
Fixes: CVE-2023-3301
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=2128929
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230619065209.442185-1-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit a0d7215e33)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context change for stable-7.2)
vhost_dev_start function does not release memory_listener object
in case of an error. This may crash the guest when vhost is unable
to set memory table:
stack trace of thread 125653:
Program terminated with signal SIGSEGV, Segmentation fault
#0 memory_listener_register (qemu-kvm + 0x6cda0f)
#1 vhost_dev_start (qemu-kvm + 0x699301)
#2 vhost_net_start (qemu-kvm + 0x45b03f)
#3 virtio_net_set_status (qemu-kvm + 0x665672)
#4 qmp_set_link (qemu-kvm + 0x548fd5)
#5 net_vhost_user_event (qemu-kvm + 0x552c45)
#6 tcp_chr_connect (qemu-kvm + 0x88d473)
#7 tcp_chr_new_client (qemu-kvm + 0x88cf83)
#8 tcp_chr_accept (qemu-kvm + 0x88b429)
#9 qio_net_listener_channel_func (qemu-kvm + 0x7ac07c)
#10 g_main_context_dispatch (libglib-2.0.so.0 + 0x54e2f)
Release memory_listener objects in the error path.
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Message-Id: <20230529114333.31686-2-ppandit@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Fixes: c471ad0e9b ("vhost_net: device IOTLB support")
Cc: qemu-stable@nongnu.org
Acked-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 1e3ffb34f7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update SeaBIOS-hppa to version 8.
Fixes:
- boot of HP-UX with SMP, and
- reboot of Linux and HP-UX with SMP
Enhancements:
- show qemu version in boot menu
- adds exit menu entry in boot menu to quit emulation
- allow to trace PCD_CHASSIS codes & machine run status
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit 34ec3aea54)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update SeaBIOS-hppa to version 7 which fixes a boot problem
with Debian-12 install CD images.
The problem with Debian-12 is, that the ramdisc got bigger
than what the firmware could load in one call to the LSI
scsi driver.
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit bb9c998ca9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: pick this one before picking next 34ec3aea54 "SeaBIOS-hppa version 8")
Give current QEMU version string to SeaBIOS-hppa via fw_cfg interface so
that the firmware can show the QEMU version in the boot menu info.
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit 069d296669)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the OS triggers a reboot, the reset helper function sends a
qemu_system_reset_request(SHUTDOWN_CAUSE_GUEST_RESET) together with an
EXCP_HLT exception to halt the CPUs.
So, at reboot when initializing the CPUs again, make sure to set all
instruction pointers to the firmware entry point, disable any interrupts,
disable data and instruction translations, enable PSW_Q bit and tell qemu
to unhalt (halted=0) the CPUs again.
This fixes the various reboot issues which were seen when rebooting a
Linux VM, including the case where even the monarch CPU has been virtually
halted from the OS (e.g. via "chcpu -d 0" inside the Linux VM).
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit 50ba97e928)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The xkb official name for the Arabic keyboard layout is 'ara'.
However xkb has for at least the past 15 years also permitted it to
be named via the legacy synonym 'ar'. In xkeyboard-config 2.39 this
synoynm was removed, which breaks compilation of QEMU:
FAILED: pc-bios/keymaps/ar
/home/fred/qemu-git/src/qemu/build-full/qemu-keymap -f pc-bios/keymaps/ar -l ar
xkbcommon: ERROR: Couldn't find file "symbols/ar" in include paths
xkbcommon: ERROR: 1 include paths searched:
xkbcommon: ERROR: /usr/share/X11/xkb
xkbcommon: ERROR: 3 include paths could not be added:
xkbcommon: ERROR: /home/fred/.config/xkb
xkbcommon: ERROR: /home/fred/.xkb
xkbcommon: ERROR: /etc/xkb
xkbcommon: ERROR: Abandoning symbols file "(unnamed)"
xkbcommon: ERROR: Failed to compile xkb_symbols
xkbcommon: ERROR: Failed to compile keymap
The upstream xkeyboard-config change removing the compat
mapping is:
470ad2cd8f
Make QEMU always ask for the 'ara' xkb layout, which should work on
both older and newer xkeyboard-config. We leave the QEMU name for
this keyboard layout as 'ar'; it is not the only one where our name
for it deviates from the xkb standard name.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20230620162024.1132013-1-peter.maydell@linaro.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1709
(cherry picked from commit 497fad3897)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We use __builtin_subcll() to do a 64-bit subtract with borrow-in and
borrow-out when the host compiler supports it. Unfortunately some
versions of Apple Clang have a bug in their implementation of this
intrinsic which means it returns the wrong value. The effect is that
a QEMU built with the affected compiler will hang when emulating x86
or m68k float80 division.
The upstream LLVM issue is:
https://github.com/llvm/llvm-project/issues/55253
The commit that introduced the bug apparently never made it into an
upstream LLVM release without the subsequent fix
fffb6e6afd
but unfortunately it did make it into Apple Clang 14.0, as shipped
in Xcode 14.3 (14.2 is reported to be OK). The Apple bug number is
FB12210478.
Add ifdefs to avoid use of __builtin_subcll() on Apple Clang version
14 or greater. There is not currently a version of Apple Clang which
has the bug fix -- when one appears we should be able to add an upper
bound to the ifdef condition so we can start using the builtin again.
We make the lower bound a conservative "any Apple clang with major
version 14 or greater" because the consequences of incorrectly
disabling the builtin when it would work are pretty small and the
consequences of not disabling it when we should are pretty bad.
Many thanks to those users who both reported this bug and also
did a lot of work in identifying the root cause; in particular
to Daniel Bertalan and osy.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1631
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1659
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Tested-by: Daniel Bertalan <dani@danielbertalan.dev>
Tested-by: Tested-By: Solra Bizna <solra@bizna.name>
Message-id: 20230622130823.1631719-1-peter.maydell@linaro.org
(cherry picked from commit b0438861ef)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The nrf51_timer has a free-running counter which we implement using
the pattern of using two fields (update_counter_ns, counter) to track
the last point at which we calculated the counter value, and the
counter value at that time. Then we can find the current counter
value by converting the difference in wall-clock time between then
and now to a tick count that we need to add to the counter value.
Unfortunately the nrf51_timer's implementation of this has a bug
which means it loses time every time update_counter() is called.
After updating s->counter it always sets s->update_counter_ns to
'now', even though the actual point when s->counter hit the new value
will be some point in the past (half a tick, say). In the worst case
(guest code in a tight loop reading the counter, icount mode) the
counter is continually queried less than a tick after it was last
read, so s->counter never advances but s->update_counter_ns does, and
the guest never makes forward progress.
The fix for this is to only advance update_counter_ns to the
timestamp of the last tick, not all the way to 'now'. (This is the
pattern used in hw/misc/mps2-fpgaio.c's counter.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20230606134917.3782215-1-peter.maydell@linaro.org
(cherry picked from commit d2f9a79a8c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In commit 2c5fa0778c we fixed an endianness bug in the Allwinner
A10 PIC model; however in the process we introduced a regression.
This is because the old code was robust against the incoming 'level'
argument being something other than 0 or 1, whereas the new code was
not.
In particular, the allwinner-sdhost code treats its IRQ line
as 0-vs-non-0 rather than 0-vs-1, so when the SD controller
set its IRQ line for any reason other than transmit the
interrupt controller would ignore it. The observed effect
was a guest timeout when rebooting the guest kernel.
Handle level values other than 0 or 1, to restore the old
behaviour.
Fixes: 2c5fa0778c ("hw/intc/allwinner-a10-pic: Don't use set_bit()/clear_bit()")
(Mjt: 5eb742fce5 in stable-7.2)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230606104609.3692557-2-peter.maydell@linaro.org
(cherry picked from commit f837b468cd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The LDG instruction loads the tag from a memory address (identified
by [Xn + offset]), and then merges that tag into the destination
register Xt. We implemented this correctly for the case when
allocation tags are enabled, but didn't get it right when ATA=0:
instead of merging the tag bits into Xt, we merged them into the
memory address [Xn + offset] and then set Xt to that.
Merge the tag bits into the old Xt value, as they should be.
Cc: qemu-stable@nongnu.org
Fixes: c15294c1e3 ("target/arm: Implement LDG, STG, ST2G instructions")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 7e2788471f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The atomic memory operations are supposed to return the old memory
data value in the destination register. This value is not
sign-extended, even if the operation is the signed minimum or
maximum. (In the pseudocode for the instructions the returned data
value is passed to ZeroExtend() to create the value in the register.)
We got this wrong because we were doing a 32-to-64 zero extend on the
result for 8 and 16 bit data values, rather than the correct amount
of zero extension.
Fix the bug by using ext8u and ext16u for the MO_8 and MO_16 data
sizes rather than ext32u.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230602155223.2040685-2-peter.maydell@linaro.org
(cherry picked from commit 243705aa6e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Command "qemu-system-riscv64 -machine virt
-m 2G -smp 1 -numa node,mem=1G -numa node,mem=1G"
would trigger this problem.Backtrace with:
#0 0x0000555555b5b1a4 in riscv_numa_get_default_cpu_node_id at ../hw/riscv/numa.c:211
#1 0x00005555558ce510 in machine_numa_finish_cpu_init at ../hw/core/machine.c:1230
#2 0x00005555558ce9d3 in machine_run_board_init at ../hw/core/machine.c:1346
#3 0x0000555555aaedc3 in qemu_init_board at ../softmmu/vl.c:2513
#4 0x0000555555aaf064 in qmp_x_exit_preconfig at ../softmmu/vl.c:2609
#5 0x0000555555ab1916 in qemu_init at ../softmmu/vl.c:3617
#6 0x000055555585463b in main at ../softmmu/main.c:47
This commit fixes the issue by adding parameter checks.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Yin Wang <yin.wang@intel.com>
Message-Id: <20230519023758.1759434-1-yin.wang@intel.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit b9cedbf19c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Some of the PMU hflags bits can go out of synch, for example a store to
MMCR0 with PMCjCE=1 fails to update hflags correctly and results in
hflags mismatch:
qemu: fatal: TCG hflags mismatch (current:0x2408003d rebuilt:0x240a003d)
This can be reproduced by running perf on a recent machine.
Some of the fragility here is the duplication of PMU hflags calculations.
This change consolidates that in a single place to update pmu-related
hflags, to be called after a well defined state changes.
The post-load PMU update is pulled out of the MSR update because it does
not depend on the MSR value.
Fixes: 8b3d1c49a9 ("target/ppc: Add new PMC HFLAGS")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530130447.372617-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 6494d2c1fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ppc hypervisors turn HEAI interrupts into program interrupts injected
into the guest that executed the illegal instruction, if the hypervisor
doesn't handle it some other way.
The nested-hv implementation failed to account for this HEAI->program
conversion. The virtual hypervisor wants to see the HEAI when running
a nested guest, so that interrupt type can be returned to its KVM
caller.
Fixes: 7cebc5db2e ("target/ppc: Introduce a vhyp framework for nested HV support")
Cc: balaton@eik.bme.hu
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230530132127.385001-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 6c242e79b8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
job may be NULL if queue->exit is true. Check
it before dereference job.
Fixes: f31f9c1080 ("vnc: add magic cookie to VncState")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit bdfca8a22f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The printed offset value is prefixed with 0x, but was actually printed
in decimal. To spare others the confusion, adjust the format specifier
to hexadecimal.
Signed-off-by: Mattias Nissler <mnissler@rivosinc.com>
Reviewed-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 5fb9e82955)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The 9p protocol does not specifically define how server shall behave when
client tries to open a special file, however from security POV it does
make sense for 9p server to prohibit opening any special file on host side
in general. A sane Linux 9p client for instance would never attempt to
open a special file on host side, it would always handle those exclusively
on its guest side. A malicious client however could potentially escape
from the exported 9p tree by creating and opening a device file on host
side.
With QEMU this could only be exploited in the following unsafe setups:
- Running QEMU binary as root AND 9p 'local' fs driver AND 'passthrough'
security model.
or
- Using 9p 'proxy' fs driver (which is running its helper daemon as
root).
These setups were already discouraged for safety reasons before,
however for obvious reasons we are now tightening behaviour on this.
Fixes: CVE-2023-2861
Reported-by: Yanwu Shen <ywsPlz@gmail.com>
Reported-by: Jietao Xiao <shawtao1125@gmail.com>
Reported-by: Jinku Li <jkli@xidian.edu.cn>
Reported-by: Wenbo Shen <shenwenbo@zju.edu.cn>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <E1q6w7r-0000Q0-NM@lizzy.crudebyte.com>
(cherry picked from commit f6b0de53fb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: drop adding qemu_fstat wrapper for 7.2 where wrappers aren't used)
Allow the Linux guest agent to attempt each of the suspend methods
(systemctl, pm-* and writing to /sys) in turn.
Prior to this guests without systemd failed to suspend due to
`guest_suspend` returning early regardless of the return value of
`systemd_supports_mode`.
Signed-off-by: Mark Somerville <mark@qpok.net>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
(cherry picked from commit 86dcb6ab9b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In qemu-user-s390x, /proc/cpuinfo contains:
processor 0: version = 00, identification = 000000, machine = 8561
processor 1: version = 00, identification = 400000, machine = 8561
The highest nibble is supposed to contain the CPU address, but it's off
by 2 bits. Fix the shift value and provide a symbolic constant for it.
With the fix we get:
processor 0: version = 00, identification = 000000, machine = 8561
processor 1: version = 00, identification = 100000, machine = 8561
Fixes: 076d4d39b6 ("s390x/cpumodel: wire up cpu type + id for TCG")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230605113950.1169228-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 71b11cbe1c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently single-stepping SVC executes two instructions. The reason is
that EXCP_DEBUG for the SVC instruction itself is masked by EXCP_SVC.
Fix by re-raising EXCP_DEBUG.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230510230213.330134-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 01b9990a3f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For M-profile, there is no guest-facing A-profile format FSR, but we
still use the env->exception.fsr field to pass fault information from
the point where a fault is raised to the code in
arm_v7m_cpu_do_interrupt() which interprets it and sets the M-profile
specific fault status registers. So it doesn't matter whether we
fill in env->exception.fsr in the short format or the LPAE format, as
long as both sides agree. As it happens arm_v7m_cpu_do_interrupt()
assumes short-form.
In compute_fsr_fsc() we weren't explicitly choosing short-form for
M-profile, but instead relied on it falling out in the wash because
arm_s1_regime_using_lpae_format() would be false. This was broken in
commit 452c67a4 when we added v8R support, because we said "PMSAv8 is
always LPAE format" (as it is for v8R), forgetting that we were
implicitly using this code path on M-profile. At that point we would
hit a g_assert_not_reached():
ERROR:../../target/arm/internals.h:549:arm_fi_to_lfsc: code should not be reached
#7 0x0000555555e055f7 in arm_fi_to_lfsc (fi=0x7fffecff9a90) at ../../target/arm/internals.h:549
#8 0x0000555555e05a27 in compute_fsr_fsc (env=0x555557356670, fi=0x7fffecff9a90, target_el=1, mmu_idx=1, ret_fsc=0x7fffecff9a1c)
at ../../target/arm/tlb_helper.c:95
#9 0x0000555555e05b62 in arm_deliver_fault (cpu=0x555557354800, addr=268961344, access_type=MMU_INST_FETCH, mmu_idx=1, fi=0x7fffecff9a90)
at ../../target/arm/tlb_helper.c:132
#10 0x0000555555e06095 in arm_cpu_tlb_fill (cs=0x555557354800, address=268961344, size=1, access_type=MMU_INST_FETCH, mmu_idx=1, probe=false, retaddr=0)
at ../../target/arm/tlb_helper.c:260
The specific assertion changed when commit fcc7404eff added
"assert not M-profile" to arm_is_secure_below_el3(), because the
conditions being checked in compute_fsr_fsc() include
arm_el_is_aa64(), which will end up calling arm_is_secure_below_el3()
and asserting before we try to call arm_fi_to_lfsc():
#7 0x0000555555efaf43 in arm_is_secure_below_el3 (env=0x5555574665a0) at ../../target/arm/cpu.h:2396
#8 0x0000555555efb103 in arm_is_el2_enabled (env=0x5555574665a0) at ../../target/arm/cpu.h:2448
#9 0x0000555555efb204 in arm_el_is_aa64 (env=0x5555574665a0, el=1) at ../../target/arm/cpu.h:2509
#10 0x0000555555efbdfd in compute_fsr_fsc (env=0x5555574665a0, fi=0x7fffecff99e0, target_el=1, mmu_idx=1, ret_fsc=0x7fffecff996c)
Avoid the assertion and the incorrect FSR format selection by
explicitly making M-profile use the short-format in this function.
Fixes: 452c67a427 ("target/arm: Enable TTBCR_EAE for ARMv8-R AArch32")a
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1658
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230523131726.866635-1-peter.maydell@linaro.org
(cherry picked from commit d7fe699be5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When passing --smp with a number lower than XLNX_ZYNQMP_NUM_APU_CPUS,
the expression (ms->smp.cpus - XLNX_ZYNQMP_NUM_APU_CPUS) will result
in a positive number as ms->smp.cpus is a unsigned int.
This will raise the following error afterwards, as Qemu will try to
instantiate some additional RPUs.
| $ qemu-system-aarch64 --smp 1 -M xlnx-zcu102
| **
| ERROR:../src/tcg/tcg.c:777:tcg_register_thread:
| assertion failed: (n < tcg_max_ctxs)
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20230524143714.565792-1-chigot@adacore.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit c9ba1c9f02)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we receive a packet from the xilinx_axienet and then try to s2mem
through the xilinx_axidma, if the descriptor ring buffer is full in the
xilinx axidma driver, we’ll assert the DMASR.HALTED in the
function : stream_process_s2mem and return 0. In the end, we’ll be stuck in
an infinite loop in axienet_eth_rx_notify.
This patch checks the DMASR.HALTED state when we try to push data
from xilinx axi-enet to xilinx axi-dma. When the DMASR.HALTED is asserted,
we will not keep pushing the data and then prevent the infinte loop.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20230519062137.1251741-1-tommy.wu@sifive.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 31afe04586)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Windows sends an extra left control key up/down input event for
every right alt key up/down input event for keyboards with
international layout. Since commit 830473455f ("ui/sdl2: fix
handling of AltGr key on Windows") QEMU uses a Windows low level
keyboard hook procedure to reliably filter out the special left
control key and to grab the keyboard on Windows.
The SDL2 version 2.0.16 introduced its own Windows low level
keyboard hook procedure to grab the keyboard. Windows calls this
callback before the QEMU keyboard hook procedure. This disables
the special left control key filter when the keyboard is grabbed.
To fix the problem, disable the SDL2 Windows low level keyboard
hook procedure.
Reported-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230418062823.5683-1-vr_qemu@t-online.de>
(cherry picked from commit 1dfea3f212)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
SDL doesn't grab Alt+F4 under Windows by default. Pressing Alt+F4 thus closes
the VM immediately without confirmation, possibly leading to data loss. Fix
this by always grabbing Alt+F4 on Windows hosts, too.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230417192139.43263-3-shentey@gmail.com>
(cherry picked from commit 083db9db44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
By default, SDL grabs Alt+Tab only in non-fullscreen mode. This causes Alt+Tab
to switch tasks on the host rather than in the VM in fullscreen mode while it
switches tasks in non-fullscreen mode in the VM. Fix this confusing behavior
by grabbing Alt+Tab in fullscreen mode, always causing tasks to be switched in
the VM.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230417192139.43263-2-shentey@gmail.com>
(cherry picked from commit efc00a3709)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
vc->gfx.w and vc->gfx.h are not updated appropriately in this code path,
which leads to a different scaling factor for rendering the cursor on
some edge cases (e.g. the focus has left and re-entered the gtk window).
This can be reproduced using vhost-user-gpu with the gtk ui on the x11
backend.
Use the surface dimensions which are already updated accordingly.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230320160856.364319-2-ernunes@redhat.com>
(cherry picked from commit f8a951bb95)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The gd_motion_event size has some calculations for the cursor position,
which also take into account things like different size of the
framebuffer compared to the window size.
The use of window size makes things more difficult though, as at least
in the case of Wayland includes the size of ui elements like a menu bar
at the top of the window. This leads to a wrong position calculation by
a few pixels.
Fix it by using the size of the widget, which already returns the size
of the actual space to render the framebuffer.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20230320160856.364319-1-ernunes@redhat.com>
(cherry picked from commit 2f31663ed4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The dmabuf->y0_top flag is passed to .dpy_gl_scanout_dmabuf(), however
in the gtk ui both implementations dropped it when doing the next
scanout_texture call.
Fixes flipped linux console using vhost-user-gpu with the gtk ui
display.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230220175605.43759-1-ernunes@redhat.com>
(cherry picked from commit 94400fa53f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
passes s->cpu_intr to i8259_init() in i82378_realize() directly. However, s-
>cpu_intr isn't initialized yet since that happens after the south bridge's
pci_realize_and_unref() in board code. Fix this by initializing s->cpu_intr
before realizing the south bridge.
Fixes: cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230304114043.121024-4-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 2237af5e60)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After "make check-venv" had been added to these jobs, they started
to re-run "configure" each time since our logic in the makefile
thinks that some files are out of date here. Avoid it with the same
trick that we are using in buildtest-template.yml already by disabling
the up-to-date check via NINJA=":".
Fixes: 1d8cf47e5b ("tests: run 'device-crash-test' from tests/venv")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230414145845.456145-2-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230424092249.58552-5-alex.bennee@linaro.org>
(cherry picked from commit 4d3bd91b26)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU aborts when default RAM backend should be used (i.e. no
explicit '-machine memory-backend=' specified) but user
has created an object which 'id' equals to default RAM backend
name used by board.
$QEMU -machine pc \
-object memory-backend-ram,id=pc.ram,size=4294967296
Actual results:
QEMU 7.2.0 monitor - type 'help' for more information
(qemu) Unexpected error in object_property_try_add() at ../qom/object.c:1239:
qemu-kvm: attempt to add duplicate property 'pc.ram' to object (type 'container')
Aborted (core dumped)
Instead of abort, check for the conflicting 'id' and exit with
an error, suggesting how to remedy the issue.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2207886
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230522131717.3780533-1-imammedo@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit a37531f238)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We cannot use the generic reentrancy guard in the LSI code, so
we have to manually prevent endless reentrancy here. The problematic
lsi_execute_script() function has already a way to detect whether
too many instructions have been executed - we just have to slightly
change the logic here that it also takes into account if the function
has been called too often in a reentrant way.
The code in fuzz-lsi53c895a-test.c has been taken from an earlier
patch by Mauro Matteo Cascella.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1563
Message-Id: <20230522091011.1082574-1-thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit b987718bbb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the OHCI controller's framenumber is incremented, HccaPad1 register
should be set to zero (Ref OHCI Spec 4.4)
ReactOS uses hccaPad1 to determine if the OHCI hardware is running,
consequently it fails this check in current qemu master.
Signed-off-by: Ryan Wendland <wendland@live.com.au>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1048
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 6301460ce9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When _FORTIFY_SOURCE=2, glibc version is 2.35, and GCC version is
12.1.0, the compiler complains as follows:
In file included from /usr/include/features.h:490,
from /usr/include/bits/libc-header-start.h:33,
from /usr/include/stdint.h:26,
from /usr/lib/gcc/aarch64-unknown-linux-gnu/12.1.0/include/stdint.h:9,
from /home/alarm/q/var/qemu/include/qemu/osdep.h:94,
from ../util/vfio-helpers.c:13:
In function 'readlink',
inlined from 'sysfs_find_group_file' at ../util/vfio-helpers.c:116:9,
inlined from 'qemu_vfio_init_pci' at ../util/vfio-helpers.c:326:18,
inlined from 'qemu_vfio_open_pci' at ../util/vfio-helpers.c:517:9:
/usr/include/bits/unistd.h:119:10: error: argument 2 is null but the corresponding size argument 3 value is 4095 [-Werror=nonnull]
119 | return __glibc_fortify (readlink, __len, sizeof (char),
| ^~~~~~~~~~~~~~~
This error implies the allocated buffer can be NULL. Use
g_file_read_link(), which allocates buffer automatically to avoid the
error.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit dbdea0dbfe)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bytes and packets counter registers are cleared on read.
Copying the "total counter" registers to the "good counter" registers has
side effects.
If the "total" register is never read by the OS, it only gets incremented.
This leads to exponential growth of the "good" register.
This commit increments the counters individually to avoid this.
Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 8d689f6aae)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: removed hw/net/igb_core.c part: igb introduced in 8.0)
The Software Developer's Manual 13.7.4.5 "Packets Transmitted (64 Bytes)
Count" says:
> This register counts the number of packets transmitted that are
> exactly 64 bytes (from <Destination Address> through <CRC>,
> inclusively) in length.
It also says similar for the other Tx statistics registers. Add the
number of bytes for CRC to those registers.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit c50b152485)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: pick this for 7.2 too: a fix by its own and makes next patch to apply cleanly)
The commit 93a97dc520 ("virtio-net: enable vq reset feature") enables
unconditionally vq reset feature as long as the device is emulated.
This makes impossible to actually disable the feature, and it causes
migration problems from qemu version previous than 7.2.
The entire final commit is unneeded as device system already enable or
disable the feature properly.
This reverts commit 93a97dc520.
Fixes: 93a97dc520 ("virtio-net: enable vq reset feature")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230504101447.389398-1-eperezma@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 1fac00f70b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU invokes vhost_svq_add() when adding a guest's element
into SVQ. In vhost_svq_add(), it uses vhost_svq_available_slots()
to check whether QEMU can add the element into SVQ. If there is
enough space, then QEMU combines some out descriptors and some
in descriptors into one descriptor chain, and adds it into
`svq->vring.desc` by vhost_svq_vring_write_descs().
Yet the problem is that, `svq->shadow_avail_idx - svq->shadow_used_idx`
in vhost_svq_available_slots() returns the number of occupied elements,
or the number of descriptor chains, instead of the number of occupied
descriptors, which may cause wrapping in SVQ descriptor ring.
Here is an example. In vhost_handle_guest_kick(), QEMU forwards
as many available buffers to device by virtqueue_pop() and
vhost_svq_add_element(). virtqueue_pop() returns a guest's element,
and then this element is added into SVQ by vhost_svq_add_element(),
a wrapper to vhost_svq_add(). If QEMU invokes virtqueue_pop() and
vhost_svq_add_element() `svq->vring.num` times,
vhost_svq_available_slots() thinks QEMU just ran out of slots and
everything should work fine. But in fact, virtqueue_pop() returns
`svq->vring.num` elements or descriptor chains, more than
`svq->vring.num` descriptors due to guest memory fragmentation,
and this causes wrapping in SVQ descriptor ring.
This bug is valid even before marking the descriptors used.
If the guest memory is fragmented, SVQ must add chains
so it can try to add more descriptors than possible.
This patch solves it by adding `num_free` field in
VhostShadowVirtqueue structure and updating this field
in vhost_svq_add() and vhost_svq_get_buf(), to record
the number of free descriptors.
Fixes: 100890f7ca ("vhost: Shadow virtqueue buffers forwarding")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230509084817.3973-1-yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
(cherry picked from commit 5d410557de)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Compared to other SSE instructions, VUCOMISx and VCOMISx are different:
the single and double precision versions are distinguished through a
prefix, however they use no-prefix and 0x66 for SS and SD respectively.
Scalar values usually are associated with 0xF2 and 0xF3.
Because of these, they incorrectly perform a 128-bit memory load instead
of a 32- or 64-bit load. Fix this by writing a custom decoding function.
I tested that the reproducer is fixed and the test-avx output does not
change.
Reported-by: Gabriele Svelto <gsvelto@mozilla.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1637
Fixes: f8d19eec0d ("target/i386: reimplement 0x0f 0x28-0x2f, add AVX", 2022-10-18)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 2b55e479e6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Using linux 6.x guest, at boot time, an inquiry on a scsi-generic
device makes qemu crash. This is caused by a buffer overflow when
scsi-generic patches the block limits VPD page.
Do the operations on a temporary on-stack buffer that is guaranteed
to be large enough.
Reported-by: Théo Maillart <tmaillart@freebox.fr>
Analyzed-by: Théo Maillart <tmaillart@freebox.fr>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 9bd634b2f5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit fe904ea824 added a fail_inactivate label, which tries to
reactivate disks on the source after a failure while s->state ==
MIGRATION_STATUS_ACTIVE, but didn't actually use the label if
qemu_savevm_state_complete_precopy() failed. This failure to
reactivate is also present in commit 6039dd5b1c (also covering the new
s->state == MIGRATION_STATUS_DEVICE state) and 403d18ae (ensuring
s->block_inactive is set more reliably).
Consolidate the two labels back into one - no matter HOW migration is
failed, if there is any chance we can reach vm_start() after having
attempted inactivation, it is essential that we have tried to restart
disks before then. This also makes the cleanup more like
migrate_fd_cancel().
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230502205212.134680-1-eblake@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 6dab4c93ec)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: minor context tweak near added comment in migration/migration.c)
No need to declare a temporary variable.
Suggested-by: Juan Quintela <quintela@redhat.com>
Fixes: 1df36e8c6289 ("migration: Handle block device inactivation failures better")
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 5d39f44d7a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Consider what happens when performing a migration between two host
machines connected to an NFS server serving multiple block devices to
the guest, when the NFS server becomes unavailable. The migration
attempts to inactivate all block devices on the source (a necessary
step before the destination can take over); but if the NFS server is
non-responsive, the attempt to inactivate can itself fail. When that
happens, the destination fails to get the migrated guest (good,
because the source wasn't able to flush everything properly):
(qemu) qemu-kvm: load of migration failed: Input/output error
at which point, our only hope for the guest is for the source to take
back control. With the current code base, the host outputs a message, but then appears to resume:
(qemu) qemu-kvm: qemu_savevm_state_complete_precopy_non_iterable: bdrv_inactivate_all() failed (-1)
(src qemu)info status
VM status: running
but a second migration attempt now asserts:
(src qemu) qemu-kvm: ../block.c:6738: int bdrv_inactivate_recurse(BlockDriverState *): Assertion `!(bs->open_flags & BDRV_O_INACTIVE)' failed.
Whether the guest is recoverable on the source after the first failure
is debatable, but what we do not want is to have qemu itself fail due
to an assertion. It looks like the problem is as follows:
In migration.c:migration_completion(), the source sets 'inactivate' to
true (since COLO is not enabled), then tries
savevm.c:qemu_savevm_state_complete_precopy() with a request to
inactivate block devices. In turn, this calls
block.c:bdrv_inactivate_all(), which fails when flushing runs up
against the non-responsive NFS server. With savevm failing, we are
now left in a state where some, but not all, of the block devices have
been inactivated; but migration_completion() then jumps to 'fail'
rather than 'fail_invalidate' and skips an attempt to reclaim those
those disks by calling bdrv_activate_all(). Even if we do attempt to
reclaim disks, we aren't taking note of failure there, either.
Thus, we have reached a state where the migration engine has forgotten
all state about whether a block device is inactive, because we did not
set s->block_inactive in enough places; so migration allows the source
to reach vm_start() and resume execution, violating the block layer
invariant that the guest CPUs should not be restarted while a device
is inactive. Note that the code in migration.c:migrate_fd_cancel()
will also try to reactivate all block devices if s->block_inactive was
set, but because we failed to set that flag after the first failure,
the source assumes it has reclaimed all devices, even though it still
has remaining inactivated devices and does not try again. Normally,
qmp_cont() will also try to reactivate all disks (or correctly fail if
the disks are not reclaimable because NFS is not yet back up), but the
auto-resumption of the source after a migration failure does not go
through qmp_cont(). And because we have left the block layer in an
inconsistent state with devices still inactivated, the later migration
attempt is hitting the assertion failure.
Since it is important to not resume the source with inactive disks,
this patch marks s->block_inactive before attempting inactivation,
rather than after succeeding, in order to prevent any vm_start() until
it has successfully reactivated all devices.
See also https://bugzilla.redhat.com/show_bug.cgi?id=2058982
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 403d18ae38)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
linux-user getgroups(), setgroups(), getgroups32() and setgroups32()
used alloca() to allocate grouplist arrays, with unchecked gidsetsize
coming from the "guest". With NGROUPS_MAX being 65536 (linux, and it
is common for an application to allocate NGROUPS_MAX for getgroups()),
this means a typical allocation is half the megabyte on the stack.
Which just overflows stack, which leads to immediate SIGSEGV in actual
system getgroups() implementation.
An example of such issue is aptitude, eg
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=811087#72
Cap gidsetsize to NGROUPS_MAX (return EINVAL if it is larger than that),
and use heap allocation for grouplist instead of alloca(). While at it,
fix coding style and make all 4 implementations identical.
Try to not impose random limits - for example, allow gidsetsize to be
negative for getgroups() - just do not allocate negative-sized grouplist
in this case but still do actual getgroups() call. But do not allow
negative gidsetsize for setgroups() since its argument is unsigned.
Capping by NGROUPS_MAX seems a bit arbitrary, - we can do more, it is
not an error if set size will be NGROUPS_MAX+1. But we should not allow
integer overflow for the array being allocated. Maybe it is enough to
just call g_try_new() and return ENOMEM if it fails.
Maybe there's also no need to convert setgroups() since this one is
usually smaller and known beforehand (KERN_NGROUPS_MAX is actually 63, -
this is apparently a kernel-imposed limit for runtime group set).
The patch fixes aptitude segfault mentioned above.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <20230409105327.1273372-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
(cherry picked from commit 1e35d32789)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reverts commit a7f523c7d1.
The nested event loop is broken by design. It's only user was removed.
Drop the code as well so that nobody ever tries to use it again.
I had to fix a couple of trivial conflicts around return values because
of 025faa872b ("vhost-user: stick to -errno error return convention").
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-3-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
(cherry picked from commit 4382138f64)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reverts commit db8a3772e3.
Motivation : this is breaking vhost-user with DPDK as reported in [0].
Received unexpected msg type. Expected 22 received 40
Fail to update device iotlb
Received unexpected msg type. Expected 40 received 22
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 1 ring restore failed: -71: Protocol error (71)
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 0 ring restore failed: -71: Protocol error (71)
unable to start vhost net: 71: falling back on userspace virtio
The failing sequence that leads to the first error is :
- QEMU sends a VHOST_USER_GET_STATUS (40) request to DPDK on the master
socket
- QEMU starts a nested event loop in order to wait for the
VHOST_USER_GET_STATUS response and to be able to process messages from
the slave channel
- DPDK sends a couple of legitimate IOTLB miss messages on the slave
channel
- QEMU processes each IOTLB request and sends VHOST_USER_IOTLB_MSG (22)
updates on the master socket
- QEMU assumes to receive a response for the latest VHOST_USER_IOTLB_MSG
but it gets the response for the VHOST_USER_GET_STATUS instead
The subsequent errors have the same root cause : the nested event loop
breaks the order by design. It lures QEMU to expect responses to the
latest message sent on the master socket to arrive first.
Since this was only needed for DAX enablement which is still not merged
upstream, just drop the code for now. A working solution will have to
be merged later on. Likely protect the master socket with a mutex
and service the slave channel with a separate thread, as discussed with
Maxime in the mail thread below.
[0] https://lore.kernel.org/qemu-devel/43145ede-89dc-280e-b953-6a2b436de395@redhat.com/
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2155173
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-2-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
(cherry picked from commit f340a59d5a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Intel specifies that the Intel IGD must occupy slot 2 on the PCI bus,
as noted in docs/igd-assign.txt in the Qemu source code.
Currently, when the xl toolstack is used to configure a Xen HVM guest with
Intel IGD passthrough to the guest with the Qemu upstream device model,
a Qemu emulated PCI device will occupy slot 2 and the Intel IGD will occupy
a different slot. This problem often prevents the guest from booting.
The only available workarounds are not good: Configure Xen HVM guests to
use the old and no longer maintained Qemu traditional device model
available from xenbits.xen.org which does reserve slot 2 for the Intel
IGD or use the "pc" machine type instead of the "xenfv" machine type and
add the xen platform device at slot 3 using a command line option
instead of patching qemu to fix the "xenfv" machine type directly. The
second workaround causes some degredation in startup performance such as
a longer boot time and reduced resolution of the grub menu that is
displayed on the monitor. This patch avoids that reduced startup
performance when using the Qemu upstream device model for Xen HVM guests
configured with the igd-passthru=on option.
To implement this feature in the Qemu upstream device model for Xen HVM
guests, introduce the following new functions, types, and macros:
* XEN_PT_DEVICE_CLASS declaration, based on the existing TYPE_XEN_PT_DEVICE
* XEN_PT_DEVICE_GET_CLASS macro helper function for XEN_PT_DEVICE_CLASS
* typedef XenPTQdevRealize function pointer
* XEN_PCI_IGD_SLOT_MASK, the value of slot_reserved_mask to reserve slot 2
* xen_igd_reserve_slot and xen_igd_clear_slot functions
Michael Tsirkin:
* Introduce XEN_PCI_IGD_DOMAIN, XEN_PCI_IGD_BUS, XEN_PCI_IGD_DEV, and
XEN_PCI_IGD_FN - use them to compute the value of XEN_PCI_IGD_SLOT_MASK
The new xen_igd_reserve_slot function uses the existing slot_reserved_mask
member of PCIBus to reserve PCI slot 2 for Xen HVM guests configured using
the xl toolstack with the gfx_passthru option enabled, which sets the
igd-passthru=on option to Qemu for the Xen HVM machine type.
The new xen_igd_reserve_slot function also needs to be implemented in
hw/xen/xen_pt_stub.c to prevent FTBFS during the link stage for the case
when Qemu is configured with --enable-xen and --disable-xen-pci-passthrough,
in which case it does nothing.
The new xen_igd_clear_slot function overrides qdev->realize of the parent
PCI device class to enable the Intel IGD to occupy slot 2 on the PCI bus
since slot 2 was reserved by xen_igd_reserve_slot when the PCI bus was
created in hw/i386/pc_piix.c for the case when igd-passthru=on.
Move the call to xen_host_pci_device_get, and the associated error
handling, from xen_pt_realize to the new xen_igd_clear_slot function to
initialize the device class and vendor values which enables the checks for
the Intel IGD to succeed. The verification that the host device is an
Intel IGD to be passed through is done by checking the domain, bus, slot,
and function values as well as by checking that gfx_passthru is enabled,
the device class is VGA, and the device vendor in Intel.
Signed-off-by: Chuck Zmudzinski <brchuckz@aol.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <b1b4a21fe9a600b1322742dda55a40e9961daa57.1674346505.git.brchuckz@aol.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
(cherry picked from commit 4f67543bb8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
xen_9pfs_free can't use gnttabdev since it is already closed and NULL-ed
out when free is called. Do the teardown in _disconnect(). This
matches the setup done in _connect().
trace-events are also added for the XenDevOps functions.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <20230502143722.15613-1-jandryuk@gmail.com>
[C.S.: - Remove redundant return in xen_9pfs_free().
- Add comment to trace-events. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
(cherry picked from commit 92e667f6fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: minor context conflict in hw/9pfs/xen-9p-backend.c)
In virtqueue_{split,packed}_get_avail_bytes() descriptors are read
in a loop via MemoryRegionCache regions and calls to
vring_{split,packed}_desc_read() - these take a region cache and the
index of the descriptor to be read.
For direct descriptors we use a cache provided by the caller, whose
size matches that of the virtqueue vring. We limit the number of
descriptors we can read by the size of that vring:
max = vq->vring.num;
...
MemoryRegionCache *desc_cache = &caches->desc;
For indirect descriptors, we initialize a new cache and limit the
number of descriptors by the size of the intermediate descriptor:
len = address_space_cache_init(&indirect_desc_cache,
vdev->dma_as,
desc.addr, desc.len, false);
desc_cache = &indirect_desc_cache;
...
max = desc.len / sizeof(VRingDesc);
However, the first initialization of `max` is done outside the loop
where we process guest descriptors, while the second one is done
inside. This means that a sequence of an indirect descriptor followed
by a direct one will leave a stale value in `max`. If the second
descriptor's `next` field is smaller than the stale value, but
greater than the size of the virtqueue ring (and thus the cached
region), a failed assertion will be triggered in
address_space_read_cached() down the call chain.
Fix this by initializing `max` inside the loop in both functions.
Fixes: 9796d0ac8f ("virtio: use address_space_map/unmap to access descriptors")
Signed-off-by: Carlos López <clopez@suse.de>
Message-Id: <20230302100358.3613-1-clopez@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit bbc1c327d7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During protocol negotiation, when we the QEMU
stub does not support a backend with F_CONFIG,
it throws a warning and supresses the
VHOST_USER_PROTOCOL_F_CONFIG bit.
However, the warning uses warn_reportf_err macro
and passes an unitialized errp pointer. However,
the macro tries to edit the 'msg' member of the
unitialized Error and segfaults.
Instead, just use warn_report, which prints a
warning message directly to the output.
Fixes: 5653493 ("hw/virtio/vhost-user: don't suppress F_CONFIG when supported")
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20230302121719.9390-1-aesteve@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 90e31232cf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
GCC13 reports an error :
../util/async.c: In function ‘aio_bh_poll’:
include/qemu/queue.h:303:22: error: storing the address of local variable ‘slice’ in ‘*ctx.bh_slice_list.sqh_last’ [-Werror=dangling-pointer=]
303 | (head)->sqh_last = &(elm)->field.sqe_next; \
| ~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
../util/async.c:169:5: note: in expansion of macro ‘QSIMPLEQ_INSERT_TAIL’
169 | QSIMPLEQ_INSERT_TAIL(&ctx->bh_slice_list, &slice, next);
| ^~~~~~~~~~~~~~~~~~~~
../util/async.c:161:17: note: ‘slice’ declared here
161 | BHListSlice slice;
| ^~~~~
../util/async.c:161:17: note: ‘ctx’ declared here
But the local variable 'slice' is removed from the global context list
in following loop of the same routine. Add a pragma to silent GCC.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230420202939.1982044-1-clg@kaod.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit d66ba6dc1c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: cherry-picked to stable-7.2 to eliminate CI failures on win*)
When we take a PNG screenshot the ordering of the colour channels in
the data is not correct, resulting in the image having weird
colouring compared to the actual display. (Specifically, on a
little-endian host the blue and red channels are swapped; on
big-endian everything is wrong.)
This happens because the pixman idea of the pixel data and the libpng
idea differ. PIXMAN_a8r8g8b8 defines that pixels are 32-bit values,
with A in bits 24-31, R in bits 16-23, G in bits 8-15 and B in bits
0-7. This means that on little-endian systems the bytes in memory
are
B G R A
and on big-endian systems they are
A R G B
libpng, on the other hand, thinks of pixels as being a series of
values for each channel, so its format PNG_COLOR_TYPE_RGB_ALPHA
always wants bytes in the order
R G B A
This isn't the same as the pixman order for either big or little
endian hosts.
The alpha channel is also unnecessary bulk in the output PNG file,
because there is no alpha information in a screenshot.
To handle the endianness issue, we already define in ui/qemu-pixman.h
various PIXMAN_BE_* and PIXMAN_LE_* values that give consistent
byte-order pixel channel formats. So we can use PIXMAN_BE_r8g8b8 and
PNG_COLOR_TYPE_RGB, which both have an in-memory byte order of
R G B
and 3 bytes per pixel.
(PPM format screenshots get this right; they already use the
PIXMAN_BE_r8g8b8 format.)
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1622
Fixes: 9a0a119a38 ("Added parameter to take screenshot with screendump as PNG")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20230502135548.2451309-1-peter.maydell@linaro.org
(cherry picked from commit cd22a0f520)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
job_cancel_locked() drops the job list lock temporarily and it may call
aio_poll(). We must assume that the list has changed after this call.
Also, with unlucky timing, it can end up freeing the job during
job_completed_txn_abort_locked(), making the job pointer invalid, too.
For both reasons, we can't just continue at block_job_next_locked(job).
Instead, start at the head of the list again after job_cancel_locked()
and skip those jobs that we already cancelled (or that are completing
anyway).
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230503140142.474404-1-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit e2626874a3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
meson.build files choose whether to build modules based on foo.found()
expressions. If a feature is enabled (e.g. --enable-gtk), these expressions
are true even if the code is not used by any emulator, and this results
in an unexpected difference between modular and non-modular builds.
For non-modular builds, the files are not included in any binary, and
therefore the source files are never processed. For modular builds,
however, all .so files are unconditionally built by default, and therefore
a normal "make" tries to build them. However, the corresponding trace-*.h
files are absent due to this conditional:
if have_system
trace_events_subdirs += [
...
'ui',
...
]
endif
which was added to avoid wasting time running tracetool on unused trace-events
files. This causes a compilation failure; fix it by skipping module builds
entirely if (depending on the module directory) have_block or have_system
are false.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit ef709860ea)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The float32_exp2 function is computing wrong exponent of 2.
For example, with the following set of values {0.1, 2.0, 2.0, -1.0},
the expected output would be {1.071773, 4.000000, 4.000000, 0.500000}.
Instead, the function is computing {1.119102, 3.382044, 3.382044, -0.191022}
Looking at the code, the float32_exp2() attempts to do this
2 3 4 5 n
x x x x x x x
e = 1 + --- + --- + --- + --- + --- + ... + --- + ...
1! 2! 3! 4! 5! n!
But because of the typo it ends up doing
x x x x x x x
e = 1 + --- + --- + --- + --- + --- + ... + --- + ...
1! 2! 3! 4! 5! n!
This is because instead of the xnp which holds the numerator, parts_muladd
is using the xp which is just 'x'. Commit '572c4d862ff2' refactored this
function, and mistakenly used xp instead of xnp.
Cc: qemu-stable@nongnu.org
Fixes: 572c4d862f "softfloat: Convert float32_exp2 to FloatParts"
Partially-Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1623
Reported-By: Luca Barbato (https://gitlab.com/lu-zero)
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Message-Id: <168304110865.537992.13059030916325018670.stgit@localhost.localdomain>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 1098cc3fcf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In allwinner-sun8i-emac we just read directly from guest memory into
a host FrameDescriptor struct and back. This only works on
little-endian hosts. Reading and writing of descriptors is already
abstracted into functions; make those functions also handle the
byte-swapping so that TransferDescriptor structs as seen by the rest
of the code are always in host-order, and fix two places that were
doing ad-hoc descriptor reading without using the functions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424165053.1428857-3-peter.maydell@linaro.org
(cherry picked from commit a4ae17e5ec)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In allwinner_sdhost_process_desc() we just read directly from
guest memory into a host TransferDescriptor struct and back.
This only works on little-endian hosts. Abstract the reading
and writing of descriptors into functions that handle the
byte-swapping so that TransferDescriptor structs as seen by
the rest of the code are always in host-order.
This fixes a failure of one of the avocado tests on s390.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424165053.1428857-2-peter.maydell@linaro.org
(cherry picked from commit 3e20d90824)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In several places in the 32-bit Arm translate.c, we try to use
load_cpu_field() to load from a CPUARMState field into a TCGv_i32
where the field is actually 64-bit. This works on little-endian
hosts, but gives the wrong half of the register on big-endian.
Add a new load_cpu_field_low32() which loads the low 32 bits
of a 64-bit field into a TCGv_i32. The new macro includes a
compile-time check against accidentally using it on a field
of the wrong size. Use it to fix the two places in the code
where we were using load_cpu_field() on a 64-bit field.
This fixes a bug where on big-endian hosts the guest would
crash after executing an ERET instruction, and a more corner
case one where some UNDEFs for attempted accesses to MSR
banked registers from Secure EL1 might go to the wrong EL.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230424153909.1419369-2-peter.maydell@linaro.org
(cherry picked from commit 7f3a3d3dc4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The Allwinner PIC model uses set_bit() and clear_bit() to update the
values in its irq_pending[] array when an interrupt arrives. However
it is using these functions wrongly: they work on an array of type
'long', and it is passing an array of type 'uint32_t'. Because the
code manually figures out the right array element, this works on
little-endian hosts and on 32-bit big-endian hosts, where bits 0..31
in a 'long' are in the same place as they are in a 'uint32_t'.
However it breaks on 64-bit big-endian hosts.
Remove the use of set_bit() and clear_bit() in favour of using
deposit32() on the array element. This fixes a bug where on
big-endian 64-bit hosts the guest kernel would hang early on in
bootup.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424152833.1334136-1-peter.maydell@linaro.org
(cherry picked from commit 2c5fa0778c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When writing the secondary-CPU stub boot loader code to the guest,
use arm_write_bootloader() instead of directly calling
rom_add_blob_fixed(). This fixes a bug on big-endian hosts, because
arm_write_bootloader() will correctly byte-swap the host-byte-order
array values into the guest-byte-order to write into the guest
memory.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424152717.1333930-4-peter.maydell@linaro.org
(cherry picked from commit 0acbdb4c4a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When writing the secondary-CPU stub boot loader code to the guest,
use arm_write_bootloader() instead of directly calling
rom_add_blob_fixed(). This fixes a bug on big-endian hosts, because
arm_write_bootloader() will correctly byte-swap the host-byte-order
array values into the guest-byte-order to write into the guest
memory.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230424152717.1333930-3-peter.maydell@linaro.org
[PMM: Moved the "make arm_write_bootloader() function public" part
to its own patch; updated commit message to note that this fixes
an actual bug; adjust to the API changes noted in previous commit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 902bba549f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The arm boot.c code includes a utility function write_bootloader()
which assists in writing a boot-code fragment into guest memory,
including handling endianness and fixing it up with entry point
addresses and similar things. This is useful not just for the boot.c
code but also in board model code, so rename it to
arm_write_bootloader() and make it globally visible.
Since we are making it public, make its API a little neater: move the
AddressSpace* argument to be next to the hwaddr argument, and allow
the fixupcontext array to be const, since we never modify it in this
function.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230424152717.1333930-2-peter.maydell@linaro.org
[PMM: Split out from another patch by Cédric, added doc comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 0fe43f0abf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The msf2-emac ethernet controller has functions emac_load_desc() and
emac_store_desc() which read and write the in-memory descriptor
blocks and handle conversion between guest and host endianness.
As currently written, emac_store_desc() does the endianness
conversion in-place; this means that it effectively consumes the
input EmacDesc struct, because on a big-endian host the fields will
be overwritten with the little-endian versions of their values.
Unfortunately, in all the callsites the code continues to access
fields in the EmacDesc struct after it has called emac_store_desc()
-- specifically, it looks at the d.next field.
The effect of this is that on a big-endian host networking doesn't
work because the address of the next descriptor is corrupted.
We could fix this by making the callsite avoid using the struct; but
it's more robust to have emac_store_desc() leave its input alone.
(emac_load_desc() also does an in-place conversion, but here this is
fine, because the function is supposed to be initializing the
struct.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20230424151919.1333299-1-peter.maydell@linaro.org
(cherry picked from commit d565f58b38)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
kvm_arm_init_debug() used to be called several times on a SMP system as
kvm_arch_init_vcpu() calls it. Move the call to kvm_arch_init() to make
sure it will be called only once; otherwise it will overwrite pointers
to memory allocated with the previous call and leak it.
Fixes: e4482ab7e3 ("target-arm: kvm - add support for HW assisted debug")
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230405153644.25300-1-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit ad5c6ddea3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In commit 5242876f37 we deprecated the dtb-kaslr-seed property of
the virt board, but forgot the "since n.n" tag in the documentation
of this in deprecated.rst.
This deprecation note first appeared in the 7.1 release, so
retrospectively add the correct "since 7.1" annotation to it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230420122256.1023709-1-peter.maydell@linaro.org
(cherry picked from commit ac64ebbecf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We are a bit premature in recommending -blockdev/-device as the best
way to configure block devices. It seems there are times the more
human friendly -drive still makes sense especially when -snapshot is
involved.
Improve the language to hopefully make things clearer.
Suggested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230424092249.58552-7-alex.bennee@linaro.org>
(cherry picked from commit c1654c3e37)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
with Q35 using ACPI PCI hotplug by default, user's request to unplug
device is ignored when it's issued before guest OS has been booted.
And any additional attempt to request device hot-unplug afterwards
results in following error:
"Device XYZ is already in the process of unplug"
arguably it can be considered as a regression introduced by [2],
before which it was possible to issue unplug request multiple
times.
Accept new uplug requests after timeout (1ms). This brings ACPI PCI
hotplug on par with native PCIe unplug behavior [1] and allows user
to repeat unplug requests at propper times.
Set expire timeout to arbitrary 1msec so user won't be able to
flood guest with SCI interrupts by calling device_del in tight loop.
PS:
ACPI spec doesn't mandate what OSPM can do with GPEx.status
bits set before it's booted => it's impl. depended.
Status bits may be retained (I tested with one Windows version)
or cleared (Linux since 2.6 kernel times) during guest's ACPI
subsystem initialization.
Clearing status bits (though not wrong per se) hides the unplug
event from guest, and it's upto user to repeat device_del later
when guest is able to handle unplug requests.
1) 18416c62e3 ("pcie: expire pending delete")
2)
Fixes: cce8944cc9 ("qdev-monitor: Forbid repeated device_del")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
CC: mst@redhat.com
CC: anisinha@redhat.com
CC: jusual@redhat.com
CC: kraxel@redhat.com
Message-Id: <20230418090449.2155757-1-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
(cherry picked from commit 0f689cf5ad)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If hostlen is zero, there is a possibility that addrstr[hostlen - 1]
underflows and, if a closing bracked is there, hostlen - 2 is passed
to g_strndup() on the next line. If websocket==false then
addrstr[0] would be a colon, but if websocket==true this could in
principle happen.
Fix it by checking hostlen.
Reported by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 3f9c41c5df)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The corruption occurs when a BAT entry aligned to 4096 bytes is changed.
Specifically, the corruption occurs during the creation of the LOG Data
Descriptor. The incorrect behavior involves copying 4088 bytes from the
original 4096 bytes aligned offset to `tmp[8..4096]` and then copying
the new value for the first BAT entry to the beginning `tmp[0..8]`.
This results in all existing BAT entries inside the 4K region being
incorrectly moved by 8 bytes and the last entry being lost.
This bug did not cause noticeable corruption when only sequentially
writing once to an empty dynamic VHDX (e.g.
using `qemu-img convert -O vhdx -o subformat=dynamic ...`), but it
still resulted in invalid values for the (unused) Sector Bitmap BAT
entries.
Importantly, this corruption would only become noticeable after the
corrupted BAT is re-read from the file.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/727
Cc: qemu-stable@nongnu.org
Signed-off-by: Lukas Tschoke <lukts330@gmail.com>
Message-Id: <6cfb6d6b-adc5-7772-c8a5-6bae9a0ad668@gmail.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 8af037fe4c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The iocb (and the allocated memory to hold LBA ranges) leaks if reading
the LBA ranges fails.
Fix this by adding a free and an unref of the iocb.
Reported-by: Coverity (CID 1508281)
Fixes: d7d1474fd8 ("hw/nvme: reimplement dsm to allow cancellation")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit 4b32319cda)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
TLS iochannel will inherit io_shutdown() from the master ioc, however we
missed to do that on the server side.
This will e.g. allow qemu_file_shutdown() to work on dest QEMU too for
migration.
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 86d063fa83)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
target_rlimit64 contains uint64_t fields, so it's 8-byte aligned on
some hosts, while some guests may align their respective type on a
4-byte boundary. This may lead to an unaligned access, which is an UB.
Fix by defining the fields as abi_ullong. This makes the host alignment
match that of the guest, and lets the compiler know that it should emit
code that can deal with the guest alignment.
While at it, also use __get_user() and __put_user() instead of
tswap64().
Fixes: 163a05a839 ("linux-user: Implement prlimit64 syscall")
Reported-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230224003907.263914-2-iii@linux.ibm.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
(cherry picked from commit 9c1da8b5ee)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixes the Windows build under msys2 using GCC 12 which fails with the following
error:
[184/579] Compiling C++ object qga/vss-win32/qga-vss.dll.p/install.cpp.obj
FAILED: qga/vss-win32/qga-vss.dll.p/install.cpp.obj
"c++" "-m64" "-mcx16" "-Iqga/vss-win32/qga-vss.dll.p" "-Iqga/vss-win32" "-I../src/qga/vss-win32" "-I." "-Iqapi" "-Itrace" "-Iui" "-Iui/shader" "-IC:/msys64/mingw64/include/glib-2.0" "-IC:/msys64/mingw64/lib/glib-2.0/include" "-fdiagnostics-color=auto" "-Wall" "-Winvalid-pch" "-Wnon-virtual-dtor" "-Werror" "-std=gnu++11" "-g" "-iquote" "." "-iquote" "C:/msys64/home/shentey/Projects/qemu/src" "-iquote" "C:/msys64/home/shentey/Projects/qemu/src/include" "-iquote" "C:/msys64/home/shentey/Projects/qemu/src/tcg/i386" "-D__STDC_LIMIT_MACROS" "-D__STDC_CONSTANT_MACROS" "-D__STDC_FORMAT_MACROS" "-fno-pie" "-no-pie" "-D_GNU_SOURCE" "-D_FILE_OFFSET_BITS=64" "-D_LARGEFILE_SOURCE" "-fno-strict-aliasing" "-fno-common" "-fwrapv" "-Wundef" "-Wwrite-strings" "-Wtype-limits" "-Wformat-security" "-Wformat-y2k" "-Winit-self" "-Wignored-qualifiers" "-Wempty-body" "-Wendif-labels" "-Wexpansion-to-defined" "-Wimplicit-fallthrough=2" "-Wmissing-format-attribute" "-Wno-missing-include-dirs" "-Wno-shift-negative-value" "-Wno-psabi" "-fstack-protector-strong" "-Wno-unknown-pragmas" "-Wno-delete-non-virtual-dtor" "-Wno-non-virtual-dtor" -MD -MQ qga/vss-win32/qga-vss.dll.p/install.cpp.obj -MF "qga/vss-win32/qga-vss.dll.p/install.cpp.obj.d" -o qga/vss-win32/qga-vss.dll.p/install.cpp.obj "-c" ../src/qga/vss-win32/install.cpp
In file included from C:/msys64/mingw64/lib/glib-2.0/include/glibconfig.h:9,
from C:/msys64/mingw64/include/glib-2.0/glib/gtypes.h:34,
from C:/msys64/mingw64/include/glib-2.0/glib/galloca.h:34,
from C:/msys64/mingw64/include/glib-2.0/glib.h:32,
from C:/msys64/home/shentey/Projects/qemu/src/include/glib-compat.h:32,
from C:/msys64/home/shentey/Projects/qemu/src/include/qemu/osdep.h:144,
from ../src/qga/vss-win32/install.cpp:13:
C:/msys64/mingw64/include/glib-2.0/glib/gmacros.h:1075:21: error: standard attributes in middle of decl-specifiers
1075 | # define G_NORETURN [[noreturn]]
| ^
C:/msys64/home/shentey/Projects/qemu/src/include/qemu/osdep.h:240:8: note: in expansion of macro 'G_NORETURN'
240 | extern G_NORETURN
| ^~~~~~~~~~
C:/msys64/mingw64/include/glib-2.0/glib/gmacros.h:1075:21: note: standard attributes must precede the decl-specifiers to apply to the declaration, or follow them to apply to the type
1075 | # define G_NORETURN [[noreturn]]
| ^
C:/msys64/home/shentey/Projects/qemu/src/include/qemu/osdep.h:240:8: note: in expansion of macro 'G_NORETURN'
240 | extern G_NORETURN
| ^~~~~~~~~~
C:/msys64/mingw64/include/glib-2.0/glib/gmacros.h:1075:21: error: attribute ignored [-Werror=attributes]
1075 | # define G_NORETURN [[noreturn]]
| ^
C:/msys64/home/shentey/Projects/qemu/src/include/qemu/osdep.h:240:8: note: in expansion of macro 'G_NORETURN'
240 | extern G_NORETURN
| ^~~~~~~~~~
C:/msys64/mingw64/include/glib-2.0/glib/gmacros.h:1075:21: note: an attribute that appertains to a type-specifier is ignored
1075 | # define G_NORETURN [[noreturn]]
| ^
C:/msys64/home/shentey/Projects/qemu/src/include/qemu/osdep.h:240:8: note: in expansion of macro 'G_NORETURN'
240 | extern G_NORETURN
| ^~~~~~~~~~
cc1plus.exe: all warnings being treated as errors
Apparently it also fixes the compilation with Clang 15 (see
https://gitlab.com/qemu-project/qemu/-/issues/1541 ).
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1541
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230318185931.181659-1-shentey@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 5cb993ff13)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
GCC13 reports an error :
../target/s390x/tcg/fpu_helper.c:123:5: error: conflicting types for ‘float_comp_to_cc’ due to enum/integer mismatch; have ‘int(CPUS390XState *, FloatRelation)’ {aka ‘int(struct CPUArchState *, FloatRelation)’} [-Werror=enum-int-mismatch]
123 | int float_comp_to_cc(CPUS390XState *env, FloatRelation float_compare)
| ^~~~~~~~~~~~~~~~
In file included from ../target/s390x/tcg/fpu_helper.c:23:
../target/s390x/s390x-internal.h:302:5: note: previous declaration of ‘float_comp_to_cc’ with type ‘int(CPUS390XState *, int)’ {aka ‘int(struct CPUArchState *, int)’}
302 | int float_comp_to_cc(CPUS390XState *env, int float_compare);
| ^~~~~~~~~~~~~~~~
Fixes: 71bfd65c5f ("softfloat: Name compare relation enum")
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230321161609.716474-3-clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit f79283fdb8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If another thread calls aio_set_fd_handler() while the IOThread event
loop is upgrading from ppoll(2) to epoll(7) then we might miss new
AioHandlers. The epollfd will not monitor the new AioHandler's fd,
resulting in hangs.
Take the AioHandler list lock while upgrading to epoll. This prevents
AioHandlers from changing while epoll is being set up. If we cannot lock
because we're in a nested event loop, then don't upgrade to epoll (it
will happen next time we're not in a nested call).
The downside to taking the lock is that the aio_set_fd_handler() thread
has to wait until the epoll upgrade is finished, which involves many
epoll_ctl(2) system calls. However, this scenario is rare and I couldn't
think of another solution that is still simple.
Reported-by: Qing Wang <qinwang@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2090998
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Fam Zheng <fam@euphon.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230323144859.1338495-1-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit e62da98527)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
At this moment, arm_load_dtb() can free machine->fdt when
binfo->dtb_filename is NULL. If there's no 'dtb_filename', 'fdt' will be
retrieved by binfo->get_dtb(). If get_dtb() returns machine->fdt, as is
the case of machvirt_dtb() from hw/arm/virt.c, fdt now has a pointer to
machine->fdt. And, in that case, the existing g_free(fdt) at the end of
arm_load_dtb() will make machine->fdt point to an invalid memory region.
Since monitor command 'dumpdtb' was introduced a couple of releases
ago, running it with any ARM machine that uses arm_load_dtb() will
crash QEMU.
Let's enable all arm_load_dtb() callers to use dumpdtb properly. Instead
of freeing 'fdt', assign it back to ms->fdt.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Fixes: bf353ad555 ("qmp/hmp, device_tree.c: introduce dumpdtb")
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-id: 20230328165935.1512846-1-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 12148d442e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The code uses the wrong base for relative addressing: it should use the
target instruction address and not the EXECUTE's address.
Fix by storing the target instruction address in the new CPUS390XState
member and loading it from the code generated by gen_ri2().
Reported-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230316210751.302423-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 703d03a4aa)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use tcg_constant_i64. Adjust in2_mri2_* to allocate a new
temporary for the output, using gen_ri2 for the address.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit bdbc87e323)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
"note_size" can be smaller than sizeof(note), so unconditionally calling
memset(notep, 0, sizeof(note)) could cause a memory corruption here in
case notep has been allocated dynamically, thus let's use note_size as
length argument for memset() instead.
Reported-by: Sebastian Mitterle <smitterl@redhat.com>
Fixes: 113d8f4e95 ("s390x: pv: Add dump support")
Message-Id: <20230214141056.680969-1-thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit eb60026120)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Guest driver might execute HW commands when shared buffers are not yet
allocated.
This could happen on purpose (malicious guest) or because of some other
guest/host address mapping error.
We need to protect againts such case.
Fixes: CVE-2022-1050
Reported-by: Raven <wxhusst@gmail.com>
Signed-off-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Message-Id: <20220403095234.2210-1-yuval.shaia.ml@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
(cherry picked from commit 31c4b6fb02)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, VMXNET3_MAX_MTU itself (being 9000) is not considered a
valid value for the MTU, but a guest running ESXi 7.0 might try to
set it and fail the assert [0].
In the Linux kernel, dev->max_mtu itself is a valid value for the MTU
and for the vmxnet3 driver it's 9000, so a guest running Linux will
also fail the assert when trying to set an MTU of 9000.
VMXNET3_MAX_MTU and s->mtu don't seem to be used in relation to buffer
allocations/accesses, so allowing the upper limit itself as a value
should be fine.
[0]: https://forum.proxmox.com/threads/114011/
Fixes: d05dcd94ae ("net: vmxnet3: validate configuration values during activate (CVE-2021-20203)")
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 099a638281)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Remove the 'change' button from "Programs and Features" because it does
not checks if a user is an admin or not. The installer has no components
to choose from and always installs everything. So the 'change' button is
not obviously needed but can create a security issue.
resolves: https://bugzilla.redhat.com/show_bug.cgi?id=2167423
fixes: CVE-2023-0664 (part 1 of 2)
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Yan Vugenfirer <yvugenfi@redhat.com>
Reported-by: Brian Wiltse <brian.wiltse@live.com>
(cherry picked from commit 88288c2a51)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
slog()'s function comment advises to use QERR_QGA_LOGGING_DISABLED.
This macro never existed. The reference got added in commit
e3d4d25206 "guest agent: add guest agent RPCs/commands" along with
QERR_QGA_LOGGING_FAILED, so maybe that one was meant. However,
QERR_QGA_LOGGING_FAILED was never actually used, and was removed in
commit d73f0beadb "qerror.h: Remove unused error classes".
Drop the dangling reference.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230207075115.1525-9-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
(cherry picked from commit c40233593e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After live migration with virtio block device, qemu crash at:
#0 0x000055914f46f795 in object_dynamic_cast_assert (obj=0x559151b7b090, typename=0x55914f80fbc4 "qio-channel", file=0x55914f80fb90 "/images/testvfe/sw/qemu.gerrit/include/io/channel.h", line=30, func=0x55914f80fcb8 <__func__.17257> "QIO_CHANNEL") at ../qom/object.c:872
#1 0x000055914f480d68 in QIO_CHANNEL (obj=0x559151b7b090) at /images/testvfe/sw/qemu.gerrit/include/io/channel.h:29
#2 0x000055914f4812f8 in qio_net_listener_set_client_func_full (listener=0x559151b7a720, func=0x55914f580b97 <tcp_chr_accept>, data=0x5591519f4ea0, notify=0x0, context=0x0) at ../io/net-listener.c:166
#3 0x000055914f580059 in tcp_chr_update_read_handler (chr=0x5591519f4ea0) at ../chardev/char-socket.c:637
#4 0x000055914f583dca in qemu_chr_be_update_read_handlers (s=0x5591519f4ea0, context=0x0) at ../chardev/char.c:226
#5 0x000055914f57b7c9 in qemu_chr_fe_set_handlers_full (b=0x559152bf23a0, fd_can_read=0x0, fd_read=0x0, fd_event=0x0, be_change=0x0, opaque=0x0, context=0x0, set_open=false, sync_state=true) at ../chardev/char-fe.c:279
#6 0x000055914f57b86d in qemu_chr_fe_set_handlers (b=0x559152bf23a0, fd_can_read=0x0, fd_read=0x0, fd_event=0x0, be_change=0x0, opaque=0x0, context=0x0, set_open=false) at ../chardev/char-fe.c:304
#7 0x000055914f378caf in vhost_user_async_close (d=0x559152bf21a0, chardev=0x559152bf23a0, vhost=0x559152bf2420, cb=0x55914f2fb8c1 <vhost_user_blk_disconnect>) at ../hw/virtio/vhost-user.c:2725
#8 0x000055914f2fba40 in vhost_user_blk_event (opaque=0x559152bf21a0, event=CHR_EVENT_CLOSED) at ../hw/block/vhost-user-blk.c:395
#9 0x000055914f58388c in chr_be_event (s=0x5591519f4ea0, event=CHR_EVENT_CLOSED) at ../chardev/char.c:61
#10 0x000055914f583905 in qemu_chr_be_event (s=0x5591519f4ea0, event=CHR_EVENT_CLOSED) at ../chardev/char.c:81
#11 0x000055914f581275 in char_socket_finalize (obj=0x5591519f4ea0) at ../chardev/char-socket.c:1083
#12 0x000055914f46f073 in object_deinit (obj=0x5591519f4ea0, type=0x5591519055c0) at ../qom/object.c:680
#13 0x000055914f46f0e5 in object_finalize (data=0x5591519f4ea0) at ../qom/object.c:694
#14 0x000055914f46ff06 in object_unref (objptr=0x5591519f4ea0) at ../qom/object.c:1202
#15 0x000055914f4715a4 in object_finalize_child_property (obj=0x559151b76c50, name=0x559151b7b250 "char3", opaque=0x5591519f4ea0) at ../qom/object.c:1747
#16 0x000055914f46ee86 in object_property_del_all (obj=0x559151b76c50) at ../qom/object.c:632
#17 0x000055914f46f0d2 in object_finalize (data=0x559151b76c50) at ../qom/object.c:693
#18 0x000055914f46ff06 in object_unref (objptr=0x559151b76c50) at ../qom/object.c:1202
#19 0x000055914f4715a4 in object_finalize_child_property (obj=0x559151b6b560, name=0x559151b76630 "chardevs", opaque=0x559151b76c50) at ../qom/object.c:1747
#20 0x000055914f46ef67 in object_property_del_child (obj=0x559151b6b560, child=0x559151b76c50) at ../qom/object.c:654
#21 0x000055914f46f042 in object_unparent (obj=0x559151b76c50) at ../qom/object.c:673
#22 0x000055914f58632a in qemu_chr_cleanup () at ../chardev/char.c:1189
#23 0x000055914f16c66c in qemu_cleanup () at ../softmmu/runstate.c:830
#24 0x000055914eee7b9e in qemu_default_main () at ../softmmu/main.c:38
#25 0x000055914eee7bcc in main (argc=86, argv=0x7ffc97cb8d88) at ../softmmu/main.c:48
In char_socket_finalize after s->listener freed, event callback function
vhost_user_blk_event will be called to handle CHR_EVENT_CLOSED.
vhost_user_blk_event is calling qio_net_listener_set_client_func_full which
is still using s->listener.
Setting s->listener = NULL after object_unref(OBJECT(s->listener)) can
solve this issue.
Signed-off-by: Yajun Wu <yajunw@nvidia.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Message-Id: <20230214021430.3638579-1-yajunw@nvidia.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit b8a7f51f59)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In vhost_svq_poll(), if vhost_svq_get_buf() fails due to a device
providing invalid descriptors, len is left uninitialized and returned
to the caller, potentally leaking stack data or causing undefined
behavior.
Fix this by initializing len to 0.
Found with GCC 13 and -fanalyzer (abridged):
../hw/virtio/vhost-shadow-virtqueue.c: In function ‘vhost_svq_poll’:
../hw/virtio/vhost-shadow-virtqueue.c:538:12: warning: use of uninitialized value ‘len’ [CWE-457] [-Wanalyzer-use-of-uninitialized-value]
538 | return len;
| ^~~
‘vhost_svq_poll’: events 1-4
|
| 522 | size_t vhost_svq_poll(VhostShadowVirtqueue *svq)
| | ^~~~~~~~~~~~~~
| | |
| | (1) entry to ‘vhost_svq_poll’
|......
| 525 | uint32_t len;
| | ~~~
| | |
| | (2) region created on stack here
| | (3) capacity: 4 bytes
|......
| 528 | if (vhost_svq_more_used(svq)) {
| | ~
| | |
| | (4) inlined call to ‘vhost_svq_more_used’ from ‘vhost_svq_poll’
(...)
| 528 | if (vhost_svq_more_used(svq)) {
| | ^~~~~~~~~~~~~~~~~~~~~~~~~
| | ||
| | |(8) ...to here
| | (7) following ‘true’ branch...
|......
| 537 | vhost_svq_get_buf(svq, &len);
| | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| | |
| | (9) calling ‘vhost_svq_get_buf’ from ‘vhost_svq_poll’
|
+--> ‘vhost_svq_get_buf’: events 10-11
|
| 416 | static VirtQueueElement *vhost_svq_get_buf(VhostShadowVirtqueue *svq,
| | ^~~~~~~~~~~~~~~~~
| | |
| | (10) entry to ‘vhost_svq_get_buf’
|......
| 423 | if (!vhost_svq_more_used(svq)) {
| | ~
| | |
| | (11) inlined call to ‘vhost_svq_more_used’ from ‘vhost_svq_get_buf’
|
(...)
|
‘vhost_svq_get_buf’: event 14
|
| 423 | if (!vhost_svq_more_used(svq)) {
| | ^
| | |
| | (14) following ‘false’ branch...
|
‘vhost_svq_get_buf’: event 15
|
|cc1:
| (15): ...to here
|
<------+
|
‘vhost_svq_poll’: events 16-17
|
| 537 | vhost_svq_get_buf(svq, &len);
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
| | |
| | (16) returning to ‘vhost_svq_poll’ from ‘vhost_svq_get_buf’
| 538 | return len;
| | ~~~
| | |
| | (17) use of uninitialized value ‘len’ here
Note by Laurent Vivier <lvivier@redhat.com>:
The return value is only used to detect an error:
vhost_svq_poll
vhost_vdpa_net_cvq_add
vhost_vdpa_net_load_cmd
vhost_vdpa_net_load_mac
-> a negative return is only used to detect error
vhost_vdpa_net_load_mq
-> a negative return is only used to detect error
vhost_vdpa_net_handle_ctrl_avail
-> a negative return is only used to detect error
Fixes: d368c0b052 ("vhost: Do not depend on !NULL VirtQueueElement on vhost_svq_flush")
Signed-off-by: Carlos López <clopez@suse.de>
Message-Id: <20230213085747.19956-1-clopez@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit e4dd39c699)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Not stopping them leave the device in a bad state when virtio-net
fronted device is unplugged with device_del monitor command.
This is not triggable in regular poweroff or qemu forces shutdown
because cleanup is called right after vhost_vdpa_dev_start(false). But
devices hot unplug does not call vdpa device cleanups. This lead to all
the vhost_vdpa devices without stop the SVQ but the last.
Fix it and clean the code, making it symmetric with
vhost_vdpa_svqs_start.
Fixes: dff4426fa6 ("vhost: Add Shadow VirtQueue kick forwarding capabilities")
Reported-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230209170004.899472-1-eperezma@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 2e1a9de96b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Mjt: this required manual edit for stable-7.2
The expiration time provided for timer_mod() can overflow if a
ridiculously large value is set to the comparator register. The
resulting value can represent a past time after rounded, forcing the
timer to fire immediately. If the timer is configured as periodic, it
will rearm the timer again, and form an endless loop.
Check if the expiration value will overflow, and if it will, stop the
timer instead of rearming the timer with the overflowed time.
This bug was found by Alexander Bulekov when fuzzing igb, a new
network device emulation:
https://patchew.org/QEMU/20230129053316.1071513-1-alxndr@bu.edu/
The fixed test case is:
fuzz/crash_2d7036941dcda1ad4380bb8a9174ed0c949bcefd
Fixes: 16b29ae180 ("Add HPET emulation to qemu (Beth Kon)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230131030037.18856-1-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 37d2bcbc2a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixup the migration compatibility for existing machine types
so that they do not enable msi-x.
Symptom:
(qemu) qemu: get_pci_config_device: Bad config data: i=0x34 read: 84 device: 98 cmask: ff wmask: 0 w1cmask:0
qemu: Failed to load PCIDevice:config
qemu: Failed to load virtio-rng:virtio
qemu: error while loading state for instance 0x0 of device '0000:00:03.0/virtio-rng'
qemu: load of migration failed: Invalid argument
Note: This fix will break migration from 7.2->7.2-fixed with this patch
bz: https://bugzilla.redhat.com/show_bug.cgi?id=2155749
Fixes: 9ea02e8f1 ("virtio-rng-pci: Allow setting nvectors, so we can use MSI-X")
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20230109105809.163975-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Daney <david.daney@fungible.com>
Fixes: 9ea02e8f1 ("virtio-rng-pci: Allow setting nvectors, so we can use MSI-X")<br>
Signed-off-by: Dr. David Alan Gilbert <<a href="mailto:dgilbert@redhat.com" target="_blank">dgilbert@redhat.com</a>><br>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit bad9c5a516)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
vhost_dev_cleanup(), called from vu_gpio_disconnect(), clears vhost_dev
so vhost-user-gpio must set the members of vhost_dev each time
connecting.
do_vhost_user_cleanup() should also acquire the pointer to vqs directly
from VHostUserGPIO instead of referring to vhost_dev as it can be called
after vhost_dev_cleanup().
Fixes: 27ba7b027f ("hw/virtio: add boilerplate for vhost-user-gpio device")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230130140320.77999-1-akihiko.odaki@daynix.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit daae36c13a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reverts commit 67f7e426e5.
Additionally to the automatic revert, I went over the code
and dropped all mentions of legacy_no_rng_seed manually,
effectively reverting a combination of 2 additional commits:
commit ffe2d2382e
Author: Jason A. Donenfeld <Jason@zx2c4.com>
Date: Wed Sep 21 11:31:34 2022 +0200
x86: re-enable rng seeding via SetupData
commit 3824e25db1
Author: Gerd Hoffmann <kraxel@redhat.com>
Date: Wed Aug 17 10:39:40 2022 +0200
x86: disable rng seeding via setup_data
Fixes: 67f7e426e5 ("hw/i386: pass RNG seed via setup_data entry")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
(cherry picked from commit 167f487358)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Mjt: this required manual edit for stable-7.2
Commit 8c460269aa ("iscsi: base all handling of check condition on
scsi_sense_to_errno", 2019-07-15) removed a "goto out" so that the
same coroutine is re-entered twice; once from iscsi_co_generic_cb,
once from the timer callback iscsi_retry_timer_expired. This can
cause a crash.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1378
Reported-by: Grzegorz Zdanowski <https://gitlab.com/kiler129>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 5080152e2e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When ADCX is followed by ADOX or vice versa, the second instruction's
carry comes from EFLAGS and the condition codes use the CC_OP_ADCOX
operation. Retrieving the carry from EFLAGS is handled by this bit
of gen_ADCOX:
tcg_gen_extract_tl(carry_in, cpu_cc_src,
ctz32(cc_op == CC_OP_ADCX ? CC_C : CC_O), 1);
Unfortunately, in this case cc_op has been overwritten by the previous
"if" statement to CC_OP_ADCOX. This works by chance when the first
instruction is ADCX; however, if the first instruction is ADOX,
ADCX will incorrectly take its carry from OF instead of CF.
Fix by moving the computation of the new cc_op at the end of the function.
The included exhaustive test case fails without this patch and passes
afterwards.
Because ADCX/ADOX need not be invoked through the VEX prefix, this
regression bisects to commit 16fc5726a6 ("target/i386: reimplement
0x0f 0x38, add AVX", 2022-10-18). However, the mistake happened a
little earlier, when BMI instructions were rewritten using the new
decoder framework.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1471
Reported-by: Paul Jolly <https://gitlab.com/myitcv>
Fixes: 1d0b926150 ("target/i386: move scalar 0F 38 and 0F 3A instruction to new decoder", 2022-10-18)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 60c7dd22e1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When a write request is converted into a write zeroes request by the
detect-zeroes= feature, it is no longer associated with an I/O buffer.
The BDRV_REQ_REGISTERED_BUF flag doesn't make sense without an I/O
buffer and must be cleared because bdrv_co_do_pwrite_zeroes() fails with
-EINVAL when it's set.
Fiona Ebner <f.ebner@proxmox.com> bisected and diagnosed this QEMU 7.2
regression where writes containing zeroes to a blockdev with
discard=unmap,detect-zeroes=unmap fail.
Buglink: https://gitlab.com/qemu-project/qemu/-/issues/1404
Fixes: e8b6535533 ("block: add BDRV_REQ_REGISTERED_BUF request flag")
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230207203719.242926-2-stefanha@redhat.com>
(cherry picked from commit 3c5867156e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In order to write the bitmap table to the image file, it is converted to
big endian. If the write fails, it is passed to clear_bitmap_table() to
free all of the clusters it had allocated before. However, if we don't
convert it back to native endianness first, we'll free things at a wrong
offset.
In practical terms, the offsets will be so high that we won't actually
free any allocated clusters, but just run into an error, but in theory
this can cause image corruption.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230112191454.169353-2-kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit b03dd9613b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unfortunately, commit f7b9dcfbcf broke populate_read_range(): the loop
end condition is very wrong, resulting in that function not populating the
full range. Lets' fix that.
Fixes: f7b9dcfbcf ("migration/ram: Factor out populating pages readable in ram_block_populate_pages()")
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 5f19a44919)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If something goes wrong during uffd_change_protection(), we would miss
to unregister uffd-wp and not release our reference. Fix it by
performing the uffd_change_protection(true) last.
Note that a uffd_change_protection(false) on the recovery path without a
prior uffd_change_protection(false) is fine.
Fixes: 278e2f551a ("migration: support UFFD write fault processing in ram_save_iterate()")
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 72ef3a3708)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ARM trusted firmware, when built with FEAT_HCX support, sets SCR_EL3.HXEn bit
to allow EL2 to modify HCRX_EL2 register without trapping it in EL3. Qemu
uses a valid mask to clear unsupported SCR_EL3 bits when emulating SCR_EL3
write, and that mask doesn't include SCR_EL3.HXEn bit even if FEAT_HCX is
enabled and exposed to the guest. As a result EL3 writes of that bit are
ignored.
Cc: qemu-stable@nongnu.org
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Message-id: 20230105221251.17896-4-eiakovlev@linux.microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 08899b5c68)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Prior to reading the shadow doorbell cq head, we have to update the
eventidx. Otherwise, we risk that the driver will skip an mmio doorbell
write. This happens on riscv64, as reported by Guenter.
Adding the missing update to the cq eventidx fixes the issue.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Cc: qemu-riscv@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
(cherry picked from commit fa5db2aa16)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The modern ACPI CPU hotplug interface was introduced in the following
series (aa1dd39ca307..679dd1a957df), released in v2.7.0:
1 abd49bc2ed docs: update ACPI CPU hotplug spec with new protocol
2 16bcab97eb pc: piix4/ich9: add 'cpu-hotplug-legacy' property
3 5e1b5d9388 acpi: cpuhp: add CPU devices AML with _STA method
4 ac35f13ba8 pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
5 d2238cb678 acpi: cpuhp: implement hot-add parts of CPU hotplug
interface
6 8872c25a26 acpi: cpuhp: implement hot-remove parts of CPU hotplug
interface
7 76623d00ae acpi: cpuhp: add cpu._OST handling
8 679dd1a957 pc: use new CPU hotplug interface since 2.7 machine type
Before patch#1, "docs/specs/acpi_cpu_hotplug.txt" only specified 1-byte
accesses for the hotplug register block. Patch#1 preserved the same
restriction for the legacy register block, but:
- it specified DWORD accesses for some of the modern registers,
- in particular, the switch from the legacy block to the modern block
would require a DWORD write to the *legacy* block.
The latter functionality was then implemented in cpu_status_write()
[hw/acpi/cpu_hotplug.c], in patch#8.
Unfortunately, all DWORD accesses depended on a dormant bug: the one
introduced in earlier commit a014ed07bd ("memory: accept mismatching
sizes in memory_region_access_valid", 2013-05-29); first released in
v1.6.0. Due to commit a014ed07bd, the DWORD accesses to the *legacy*
CPU hotplug register block would work in spite of the above series *not*
relaxing "valid.max_access_size = 1" in "hw/acpi/cpu_hotplug.c":
> static const MemoryRegionOps AcpiCpuHotplug_ops = {
> .read = cpu_status_read,
> .write = cpu_status_write,
> .endianness = DEVICE_LITTLE_ENDIAN,
> .valid = {
> .min_access_size = 1,
> .max_access_size = 1,
> },
> };
Later, in commits e6d0c3ce68 ("acpi: cpuhp: introduce 'Command data 2'
field", 2020-01-22) and ae340aa3d2 ("acpi: cpuhp: spec: add typical
usecases", 2020-01-22), first released in v5.0.0, the modern CPU hotplug
interface (including the documentation) was extended with another DWORD
*read* access, namely to the "Command data 2" register, which would be
important for the guest to confirm whether it managed to switch the
register block from legacy to modern.
This functionality too silently depended on the bug from commit
a014ed07bd.
In commit 5d971f9e67 ('memory: Revert "memory: accept mismatching sizes
in memory_region_access_valid"', 2020-06-26), first released in v5.1.0,
the bug from commit a014ed07bd was fixed (the commit was reverted).
That swiftly exposed the bug in "AcpiCpuHotplug_ops", still present from
the v2.7.0 series quoted at the top -- namely the fact that
"valid.max_access_size = 1" didn't match what the guest was supposed to
do, according to the spec ("docs/specs/acpi_cpu_hotplug.txt").
The symptom is that the "modern interface negotiation protocol"
described in commit ae340aa3d2:
> + Use following steps to detect and enable modern CPU hotplug interface:
> + 1. Store 0x0 to the 'CPU selector' register,
> + attempting to switch to modern mode
> + 2. Store 0x0 to the 'CPU selector' register,
> + to ensure valid selector value
> + 3. Store 0x0 to the 'Command field' register,
> + 4. Read the 'Command data 2' register.
> + If read value is 0x0, the modern interface is enabled.
> + Otherwise legacy or no CPU hotplug interface available
falls apart for the guest: steps 1 and 2 are lost, because they are DWORD
writes; so no switching happens. Step 3 (a single-byte write) is not
lost, but it has no effect; see the condition in cpu_status_write() in
patch#8. And step 4 *misleads* the guest into thinking that the switch
worked: the DWORD read is lost again -- it returns zero to the guest
without ever reaching the device model, so the guest never learns the
switch didn't work.
This means that guest behavior centered on the "Command data 2" register
worked *only* in the v5.0.0 release; it got effectively regressed in
v5.1.0.
To make things *even more* complicated, the breakage was (and remains, as
of today) visible with TCG acceleration only. Commit 5d971f9e67 makes
no difference with KVM acceleration -- the DWORD accesses still work,
despite "valid.max_access_size = 1".
As commit 5d971f9e67 suggests, fix the problem by raising
"valid.max_access_size" to 4 -- the spec now clearly instructs the guest
to perform DWORD accesses to the legacy register block too, for enabling
(and verifying!) the modern block. In order to keep compatibility for the
device model implementation though, set "impl.max_access_size = 1", so
that wide accesses be split before they reach the legacy read/write
handlers, like they always have been on KVM, and like they were on TCG
before 5d971f9e67 (v5.1.0).
Tested with:
- OVMF IA32 + qemu-system-i386, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32X64 + qemu-system-x86_64, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32 + qemu-system-i386, SMM enabled, using TCG accel; verified the
register block switch and the present/possible CPU counting through the
modern hotplug interface, during OVMF boot (bugfix test);
- I do not have any testcase (guest payload) for regression-testing CPU
hotplug through the *legacy* CPU hotplug register block.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
Ref: "IO port write width clamping differs between TCG and KVM"
Link: http://mid.mail-archive.com/aaedee84-d3ed-a4f9-21e7-d221a28d1683@redhat.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2023-01/msg00199.html
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230105161804.82486-1-lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit dab30fbef3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When installing shared libraries, as is the case for libvfio-user.so,
Meson will include relative symbolic links in the output of
"meson introspect --installed":
{
"libvfio-user.so": "/usr/local/lib64/libvfio-user.so",
...
}
In the case of scripts/symlink-install-tree.py, this will
be a symbolic link to a symbolic link but, in any case, there is
no issue in creating it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit f32eb0021a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The check semihosting_enabled() wants to know if the guest is
currently in user mode. Unlike the other cases the test was inverted
causing us to block semihosting calls in non-EL0 modes.
Cc: qemu-stable@nongnu.org
Fixes: 19b26317e9 (target/arm: Honour -semihosting-config userspace=on)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 9788d4c007)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When vIOMMU is enabled, the vq->used_phys is actually the IOVA not
GPA. So we need to translate it to GPA before the syncing otherwise we
may hit the following crash since IOVA could be out of the scope of
the GPA log size. This could be noted when using virtio-IOMMU with
vhost using 1G memory.
Fixes: c471ad0e9b ("vhost_net: device IOTLB support")
Cc: qemu-stable@nongnu.org
Tested-by: Lei Yang <leiyang@redhat.com>
Reported-by: Yalan Zhang <yalzhang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221216033552.77087-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 345cc1cbcb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
- if test -n "@PYPI_PKGS@" ; then @PIP3@ install @PYPI_PKGS@ ; fi
- if test -n "@PYPI_PKGS@" ; then PYLIB=$(@PYTHON@ -c 'import sysconfig; print(sysconfig.get_path("stdlib"))'); rm -f $PYLIB/EXTERNALLY-MANAGED; @PIP3@ install @PYPI_PKGS@ ; fi
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
